The example of shafts; a) Rotating Machinery; Propeller shaft, Drive shaft b) Structural Systems; Landing gear strut, Flap drive mechanism

Size: px
Start display at page:

Download "The example of shafts; a) Rotating Machinery; Propeller shaft, Drive shaft b) Structural Systems; Landing gear strut, Flap drive mechanism"

Transcription

1 TORSION OBJECTIVES: This chapter starts with torsion theory in the circular cross section followed by the behaviour of torsion member. The calculation of the stress stress and the angle of twist will be also showed here. Lastly, the topics that include the members having noncircular cross sections will be discussed. The examples and exercises will be included to better understanding. 5.1 Introduction Torsion refers to the twisting of a structural member that is loaded by couples or torque. It will produce rotation about the member s longitudinal axis. Couples that produce twisting of a bar are called torques, twisting couples or twisting moments and may be represented in several ways. The example of shafts; a) Rotating Machinery; Propeller shaft, Drive shaft b) Structural Systems; Landing gear strut, Flap drive mechanism Figure.1: Example of driving shaft Mechanics of Materials 177

2 5. Torsion theory of circular cross section Figure. : The circular cross section Shaft connecting gears and pulleys are a common application involving torsion members. To examine the stress and deformation of a torsion member, a prismatic bar with a circular cross section that is twisted by torques, T acting at the ends will be considered as shown in Figure.. (a) Before deformation (b) After deformation Figure.3: Deformation of bar To better understand the behaviour of a torsion member, superimpose a grid on the surface of shaft and observe the deformation of the shaft as a result of the applied torque, T. Hold the left end of the bar fixed in position. When a bar or shaft of circular section is twisted by moment, its Mechanics of Materials 178

3 called pure tension and the deformed element shown in Figure.3 are said to be in a state of pure shear. Figure. Referring to Figure.3 and., several characteristics of torsional loading on the circular prismatic bar is observed; 1. The longitudinal axis of the shaft remains straight.. The shaft does not increase or decrease in length. 3. Radial lines remain straight and radial as the cross section rotates.. Cross sections rotate about the axis of the member. The warping does not occur in circular section. The theory of torsion with the circular section is relatively simple Shear stress in circular section, τ (tau) Tr J Where; τ : Shear stress in the shaft if τ max =maximum shear stress occurs at the outer tegasan ricih. (N/m ) J : Polar moment of inertia of the cross sectional moment sifatekun kutub (m ) T : Applied torque acting at the cross section (Nm) r : Radius of the shaft (m) Mechanics of Materials 179

4 5.. Types of circular section 5..3 Angles of twist, ( sudut piuhan Where; TL JG Ө = angle of twist (radians) T = applied torque L = length of member G = shear modulus of material/ modulus of rigidity@modulus ketegaran (N/m ) J = polar moment of inertia 5.. Power transmission Circular bars or shafts are commonly used for transmission of power. From design stand point, it is necessary for the shaft to be strong enough to transmit power safely without exceeding the shaft material's elastic limit. Power is defined as the work performed per unit of time. The work transmitted by a rotating shaft equals to the torque applied times the angle of rotation. Work = Torque x Angular Displacement Mechanics of Materials 180

5 Power = d/dt (Work) If torque is not a function of time, then the equation for power simply becomes: P = T ω Where; ω is the angular velocity of the shaft (rad/s) T : Applied torque acting at the cross section (Nm) P : Power (W)(1W = 1 Nm/s) For machinery, the frequency of a shaft s rotation, f is often reported. This is a measure of the revolutions number@cycles of the shaft. P = π f T Where; f : frequency hertz) (1 Hz = 1 cycle/s) ω: π f It is important that we use consistent units for P, T, and ω. Power is commonly specified in horsepower, HP. Angular velocity is usually given in revolutions per minute or RPM. It should then be converted to rad/sec. To do this multiply the value in RPM by π and divide by 0. EXAMPLE.1 Determine the maximum torque of a hollow circular shaft with inside diameter of 0mm and an outside diameter of 100mm without exceeding the maximum shearing stress of 70MPa. Solution; Given; d i = 0mm, τ max = 70MPa d o = 100mm J ( ) 8.55x10 mm Mechanics of Materials 181

6 Tmax r max J max J Tmax r (70x10 )(8.55x ) 11.97kNm Remember: τ max =maximum shear stress occurs at the outer surface/radius. EXAMPLE. A hollow steel shaft has an outside diameter of 150mm and an inside diameter 100mm. The shaft is subjected to a torque of 35kNm. The modulus of rigidity for the steel is 80GPa. Determine; a) the shearing stress at the outside surface of the shaft. b) the shearing stress at the inside surface of the shaft. c) the magnitude of the angle of twist in a.5m length. Solution; J ( ) 39.89x10 mm a) the shearing stress at the outside surface of the shaft. Tr out J 3 35x10 (0.075) 5.81MPa 39.89x10 b) the shearing stress at the inside surface of the shaft Tr in J 3 35x10 (0.05) 3.9MPa 39.89x10 c) the magnitude of the angle of twist in a.5m length. TL JG 3 35x10 (.5) 9 80x10 (39.89x rad ) Mechanics of Materials 18

7 EXAMPLE.3 A 3m long hollow steel shaft has an outside diameter of 100mm and an inside diameter of 0mm. The shear modulus of steel is 80GPa. The maximum shearing stress in the shaft is 80MPa and the angular velocity is 00rpm. Determine; a) the power being transmitted by the shaft. b) the magnitude of the angle of twist in the shaft. Solution; J ( ) 8.55x10 mm Tmax r max J max J Tmax r (80x10 )(8.55x ) 13.8kNm a) the power being transmitted by the shaft. From the previous notes stated that angular velocity is usually given in revolutions per minute or RPM. It should then be converted to rad/sec. To do this multiply the value in RPM by π and divide by 0. 3 T (00)(13.8x10 ) P Hp( horse power ) 8. 55kW 0 0 b) the magnitude of the angle of twist in the shaft. TL JG x10 (3) 0.0rad 9 80x10 (8.55x10 ) Mechanics of Materials 183

8 EXAMPLE. A solid circular steel shaft 1.5m long transmits 00kW at a speed of 00rpm. If the allowable shearing stress is 70MPa and the allowable angle of twist is 0.05 rad. The shear modulus of steel is 80GPa. a) the minimum permissible diameter for the shaft. b) the speed at the same power that can be delivered if the stress is not exceed 50MPa in a diameter of 75mm. Solution; Given L =1.5m P = 00kW ω = 00 rpm τ allow = 70MPa allow =.º or 0.05 rad G = 80GPa a) P T T 0 (00) 00x10 0 T. 77kNm 3 T i) Tr allow J.77x10 allow d 3 385d 70x d 3 d ii) allow TL JG.77 d 3 3 x10 (1.5) (80x10 ) x10 = d d 0.07mm@7. 1mm 70x 10 d Pick d = 70.7mm b) Given d = 75mm d 0.07m@70. 7mm J d (75) 3 3 Tr J 3.11x10 mm Mechanics of Materials 18

9 T(0.0375) 3.11x10 50x 10 T =.15kNm P T T (.15x10 ) 00x10 0 = 1rpm EXERCISE.1 A hollow circular shaft has an outside diameter D of 100mm and an inside diameter D 1 of 0mm. Given the maximum allowable shearing stress is 55 N/mm. a) Show that its polar moment of inertia, J is 8.55x10 mm. b) Calculate the maximum torque, T that can applied to the shaft c) Determine the shear stress at the inner surface of the hollow shaft EXERCISE. A tubular shaft having an inner diameter of 30mm and outer diameter of mm is to be used to transmit 90kW of power. Determine the frequency of rotation of the shaft so that the shear stress will not exceed 50MPa. [Ans: f =.Hz] Mechanics of Materials 185

10 5.3 Composite Bars A B C Shaft 1 Shaft To solve the problem of combined/composite shaft; a) T = T shaft 1 + T shaft +..T shaft n n = number of shaft b) 1 c) TL JG EXAMPLE.5 The composite bars with the different material is subjected to the torque is shown in figure. Determine the maximum shear stress and the position. Determine the angle of twist at C. 10kNm A B C knm m 0.3m BAR r (mm) G(Pa) AB 50 3x10 10 BC 5 8x10 10 Solution; J AB d 3 (100 ) 3 9.8x10 mm J BC d 3 (50 ) 3 0.x10 mm 10kNm A B C knm T = outward ( ) T = inward ( ) m 0.3m Or applied Right Hand Rule Mechanics of Materials 18

11 knm 10kNm A B C knm T A m 0.3m knm T AB = knm (T) knm 10kNm T BC = knm(c) Maximum shear stress; TABrAB x10 (50) AB 30.55N / mm J 9.8x10 AB BC TBC r J BC BC x10 (5) 0.x N / mm The maximum shear stress occurs in the bar of BC. Angle of twist at the end of C; TL TL TL JG JG JG AB BC (x10 )(000) ( x10 )(300) 9.8x10 (3x10 ) 0.x10 (8x10 ) rad Mechanics of Materials 187

12 EXERCISE.3 The horizontal shaft AD is attached to a fixed support at D and is subjected to point torques as shown in figure. A 0mm diameter hole has been drilled into the portion CD of the shaft. By assuming that the entire shaft is made of steel and G =70GN/m, determine the angle of twist at end A. 5. Torsion of non-cylindrical member Generally, we deal with axisymmetric bodies and the shear strain is linear through the entire body. However, non-circular cross-sections are not axisymmetric causing complex behaviors, which may cause bulging or warping when the shaft is twisted. Figure.5: Condition of bulging of non-circular shaft Mechanics of Materials 188

13 The mathematics is beyond the scope of the course, however there are empirical formulas for various shapes. Table.1: Formula for various shapes EXAMPLE. The aluminum shaft shown in figure has a cross sectional area in the shape of an equilateral triangle. Determine the largest torque, T that can be applied to the end of the shaft if the allowable shear stress, allow is = 5MPa and the angle of twist at its end is restricted to allow= 0.0 rad. Given G al = GPa. Mechanics of Materials 189

14 Solution; By inspection, the type of shaft is equilateral triangle. Refer to Table.1, i) 0T allow 3 a 0T 5N / mm 3 0 T 179. knmm TL ii) allow a Gal T (100mm) T (1.m) 0.0rad or 0.0rad 3 N (0 mm)(x10 ) (0.0 m)(x10 mm T. 1kNmm T. 1Nm 9 N m ) By comparison, the torque is limited due to the angle of twist. T. 1kNmm 5.5 Thin-walled Having Closed Cross Sections Thin walled of noncircular shape are often used to construct lightweight frameworks which is used in aircraft. In this section, we will analyze the effects of applying a torque to a thin walled having a closed cross section. The section does not have any breaks or slits along its length Shear flow, q. Due the applied torque, T, shear stress is developed on the front face of the element. Shear flow in a solid body is the gradient of a shear stress through the body. Shear flow is the product of the tube s thickness and the average shear stress. This value is constant at all points along the tube s cross section. As a result, the largest average shear stress on the cross section occurs where the tube s thickness is small. q t avg Mechanics of Materials 190

15 5.5. Average shear stress, ave In non-circular thin walled shafts for closed segments. We assume that the stress is uniformly distributed across the thickness and that we can assume an average shear stress. The average shear stress in the body is; ave T ta m where, ave - average shear stress t - the thickness of the shaft at the point of interest A m - mean area enclosed within the boundary of the centerline of the shaft thickness. T - the applied torque A m is shown in shaded area. The relationship between shear stress, τ and torque, T; df ds τ ave t h τ ave T dt h(df) Mechanics of Materials 191

16 h( ave ave t ave ave t t ds) t h ds d A m A m ave T ta m Since q avg section using the equation; t, we can determine the shear flow throughout the cross q T A m Angle of twist, This angle can be determined by using the energy method. The angle given in radians, can be expressed as; TL A m G ds t Here the integration must be performed around the entire boundary of the tube s cross sectional area. where, t - thickness of the interior segment L - length of the section G - modulus of rigidity of the section/shear modulus Mechanics of Materials 19

17 EXAMPLE.7 The tube is made of bronze and has a rectangular section as shown in figure. If it is subjected to the two torques; a) determine the average shear stress in the tube at points A and B. b) determine the angle of twist at end C. Given G = 38GPa. Solution; a) 0Nm 5Nm C D E 0Nm 0Nm T CD = 0Nm (T) 0Nm 5Nm 35Nm T DE = 35Nm (T) OR The tube is subjected to the two torques at C and D. The free body diagram is shown in figure. The internal torque is 35 Nm. T = T 0 = > to balance (0-5)=35Nm Mechanics of Materials 193

18 The area, A m ; A m ( 0.035)(0.057) 0.00m 57mm The shaded area = A m 35mm The average shear stress at point A with t A = 5mm; T ave tam 35 A 1. 75MPa (0.005)(0.00) The average shear stress at point B with t B = 3mm; 35 B. 9MPa (0.003)(0.00) b) The internal torques in regions DE and CD are 35Nm and 0Nm, respectively. TL ds TL ds A t t m G A CD m G DE 0(0.5) 57mm 35mm 9 (0.00 )(38x10 ) 5mm 3mm Mechanics of Materials 19

19 35(1.5) 57mm 35mm 9 (0.00 )(38x10 ) 5mm 3mm x10.x x10 rad EXAMPLE.8 A square aluminum tube has the dimensions as shown in figure. a) determine the average shear stress in the tube at point A if it is subjected to a torque of 85Nm. b) compute the angle of twist due to this loading. Given G al = GPa. 1.5m Solution; a) The area, A m ; A m ( 50)(50) 500mm 50mm The shaded area = A m avg T ta m 50mm 3 85x10 (10)(500) 1.7N / mm Mechanics of Materials 195

20 Since t is a constant because of the square tube, the average shear stress is the same at all points on the cross section. b) Angle of twist; TL A m G ds t 3 (85x10 )(1500) 50mm 3 (500) (x10 ) 10mm 1.9x10 (0) 3.9x10 3 rad Here, the integral represents the length around the centerline boundary of the tube. EXERCISE. If a =5mm and b = 15mm, determine the maximum shear stress in the circular and elliptical shafts when applied torque is T=80Nm. By what percentage is the shaft of circular section more efficient at withstanding the torque than the shaft of elliptical cross section? [Ans: b) τ (max)c = 3.MPa, τ (max)e = 9.05MPa, 178%] Mechanics of Materials 19

21 EXERCISE.5 The square shaft is used at the end of a drive cable in order to registrar the rotation of the cable on a gauge. If it has the dimensions shown and is subjected to a torque of 8Nm, determine the shear stress in the shaft at point A. Mechanics of Materials 197

22 TUTORIAL 5 1. a) If the shearing stress is not exceed 70 N/mm, determine the maximum torque that may be transmitted by a solid circular shaft of diameter 98.5mm and length of 1.m. Take shear modulus of steel is 80kN/mm. b) The square thin walled tube is subjected to a torque of 150Nm. Determine the average shear stress in the tube if the mean dimension a = 00mm. Each side has a thickness of t = 3mm. [Ans: a) τ ave = 1.5MPa] a. a) A hollow circular shaft has an outside diameter D of 100mm and an inside diameter D 1 of 75mm. Show that its polar moment of inertia, J is.71x10 mm. Given the maximum allowable shearing stress is 5 N/mm. Calculate; i) the maximum torque, T that can applied to the shaft. ii) the shear stress at the inner surface of the hollow shaft. b) A continuous circular shaft is made of two segments AB and BC with diameters 05mm and 105mm respectively. The shaft is fixed at the end A and subjected to anticlockwise torques of 0kNm at B and 30kNm at C as shown in figure. Take G = 80kN/mm. Find the total angle of twist at the end C. Mechanics of Materials 198

23 3. a) The figure shows the cross sectional of a hollow shaft. Prove the torsion equation for concentrically hollow circular shafts is given by expression; T J R max where; T = applied torque R = outer radius of the shaft R 1 = inner radius of the shaft τ max = shear stress at outer radius R J = polar moment of inertia dr = an elementary ring of a thickness at r, radius. b) A hollow steel shaft is subjected to receive a torque of 30kNm. The shaft has an outside diameter of 150mm and inside diameter of 100mm. The Modulus of Rigidity for the steel is 80GPa. Determine; i) the shear stress on the outside surface of the shaft. ii) the shear stress on the inside surface of the shaft. iii) the maximum shear stress of the shaft. iv) the twist angle for a 3.5m length of the shaft.. a) Discuss THREE (3) assumptions to be made in the derivation of torsion equation for a circular shaft. b) A steel circular bar in torsion consists of two parts, as shown in Figure Q(a). Part AB has diameter 0 mm and length 1 m, and part BC has diameter 30 mm and length 1. m. What is the allowable torque T if the angle of twist between the ends of the bar is not to exceed radians and the shear stress is not to exceed 30 MPa? Assume Modulus of Rigidity, G steel = 80 GPa. c) A torque of 5 knm is applied to the rectangular section shown in Figure Q(b). Determine the wall thickness t so as not to exceed a shear stress of 80 MPa. Mechanics of Materials 199

24 0 mm 30 mm T A B C T 1 m 1. m Figure Q(a) t 50 mm 100 mm Figure Q(c) (FINAL EXAM SEM II 007/008 UTHM) 5. A hollow section as shown in Figure Q5 is subjected to a torque of 100Nm at point A. a) Sketch a thin wall tube to show elements subjected to torsion. b) Derive the equation of average shear stress, τ ave in terms of internal torque, T, the thickness of hollow section, t and the mean area enclosed within the boundary of the centre line of the thickness of the hollow section. c) Determine the average shear stress in the hollow section at point A. Mechanics of Materials 00

25 d) Calculate the angle of twist assuming G = 00GPa. 0 A 00 L = 3m Figure Q5 All units in mm (FINAL EXAM SEM I 007/008 UTHM). a) Determine the torque T that can be applied to the rectangular tube if the average shear stress is no exceed 85MPa. The mean dimensions of the tube are shown and the tube has thickness of 3mm. 50mm 100mm [Ans: a) T =.55kNm] b) The solid compound rod made of three different materials carried the two torques as shown in Figure Q3. Given G aluminum = 8GPa, G bronze = 35GPa dan G steel = 83GPa. (Answer in unit N/mm ). i) Calculate the maximum shear stress in each material. ii) Find the angle of rotation of the free end of the rod. Mechanics of Materials 01

26 5 kn.m Aluminum Steel Bronze kn.m 100 mm 75 mm 3 m m 1.5 m Mechanics of Materials 0

The problem of transmitting a torque or rotary motion from one plane to another is frequently encountered in machine design.

The problem of transmitting a torque or rotary motion from one plane to another is frequently encountered in machine design. CHAPER ORSION ORSION orsion refers to the twisting of a structural member when it is loaded by moments/torques that produce rotation about the longitudinal axis of the member he problem of transmitting

More information

(48) CHAPTER 3: TORSION

(48) CHAPTER 3: TORSION (48) CHAPTER 3: TORSION Introduction: In this chapter structural members and machine parts that are in torsion will be considered. More specifically, you will analyze the stresses and strains in members

More information

Stress Analysis Lecture 3 ME 276 Spring Dr./ Ahmed Mohamed Nagib Elmekawy

Stress Analysis Lecture 3 ME 276 Spring Dr./ Ahmed Mohamed Nagib Elmekawy Stress Analysis Lecture 3 ME 276 Spring 2017-2018 Dr./ Ahmed Mohamed Nagib Elmekawy Axial Stress 2 Beam under the action of two tensile forces 3 Beam under the action of two tensile forces 4 Shear Stress

More information

Chapter 5 Torsion STRUCTURAL MECHANICS: CE203. Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson

Chapter 5 Torsion STRUCTURAL MECHANICS: CE203. Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson STRUCTURAL MECHANICS: CE203 Chapter 5 Torsion Notes are based on Mechanics of Materials: by R. C. Hibbeler, 7th Edition, Pearson Dr B. Achour & Dr Eng. K. El-kashif Civil Engineering Department, University

More information

CIVL222 STRENGTH OF MATERIALS. Chapter 6. Torsion

CIVL222 STRENGTH OF MATERIALS. Chapter 6. Torsion CIVL222 STRENGTH OF MATERIALS Chapter 6 Torsion Definition Torque is a moment that tends to twist a member about its longitudinal axis. Slender members subjected to a twisting load are said to be in torsion.

More information

MECE 3321: MECHANICS OF SOLIDS CHAPTER 5

MECE 3321: MECHANICS OF SOLIDS CHAPTER 5 MECE 3321: MECHANICS OF SOLIDS CHAPTER 5 SAMANTHA RAMIREZ TORSION Torque A moment that tends to twist a member about its longitudinal axis 1 TORSIONAL DEFORMATION OF A CIRCULAR SHAFT Assumption If the

More information

[7] Torsion. [7.1] Torsion. [7.2] Statically Indeterminate Torsion. [7] Torsion Page 1 of 21

[7] Torsion. [7.1] Torsion. [7.2] Statically Indeterminate Torsion. [7] Torsion Page 1 of 21 [7] Torsion Page 1 of 21 [7] Torsion [7.1] Torsion [7.2] Statically Indeterminate Torsion [7] Torsion Page 2 of 21 [7.1] Torsion SHEAR STRAIN DUE TO TORSION 1) A shaft with a circular cross section is

More information

Chapter 5: Torsion. 1. Torsional Deformation of a Circular Shaft 2. The Torsion Formula 3. Power Transmission 4. Angle of Twist CHAPTER OBJECTIVES

Chapter 5: Torsion. 1. Torsional Deformation of a Circular Shaft 2. The Torsion Formula 3. Power Transmission 4. Angle of Twist CHAPTER OBJECTIVES CHAPTER OBJECTIVES Chapter 5: Torsion Discuss effects of applying torsional loading to a long straight member (shaft or tube) Determine stress distribution within the member under torsional load Determine

More information

Torsion Stresses in Tubes and Rods

Torsion Stresses in Tubes and Rods Torsion Stresses in Tubes and Rods This initial analysis is valid only for a restricted range of problem for which the assumptions are: Rod is initially straight. Rod twists without bending. Material is

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS 2009 The McGraw-Hill Companies, Inc. All rights reserved. Fifth SI Edition CHAPTER 3 MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David F. Mazurek Torsion Lecture Notes:

More information

Structural Analysis I Chapter 4 - Torsion TORSION

Structural Analysis I Chapter 4 - Torsion TORSION ORSION orsional stress results from the action of torsional or twisting moments acting about the longitudinal axis of a shaft. he effect of the application of a torsional moment, combined with appropriate

More information

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,

More information

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion Introduction Stress and strain in components subjected to torque T Circular Cross-section shape Material Shaft design Non-circular

More information

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics Page1 PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [2910601] Introduction, Fundamentals of Statics 1. Differentiate between Scalar and Vector quantity. Write S.I.

More information

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A DEPARTMENT: CIVIL SUBJECT CODE: CE2201 QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State

More information

3.5 STRESS AND STRAIN IN PURE SHEAR. The next element is in a state of pure shear.

3.5 STRESS AND STRAIN IN PURE SHEAR. The next element is in a state of pure shear. 3.5 STRESS AND STRAIN IN PURE SHEAR The next element is in a state of pure shear. Fig. 3-20 Stresses acting on a stress element cut from a bar in torsion (pure shear) Stresses on inclined planes Fig. 3-21

More information

Mechanical Design in Optical Engineering

Mechanical Design in Optical Engineering Torsion Torsion: Torsion refers to the twisting of a structural member that is loaded by couples (torque) that produce rotation about the member s longitudinal axis. In other words, the member is loaded

More information

Sub. Code:

Sub. Code: Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. ) The model answer and the answer written by candidate may

More information

MECHANICS OF SOLIDS TORSION - TUTORIAL 1. You should judge your progress by completing the self assessment exercises.

MECHANICS OF SOLIDS TORSION - TUTORIAL 1. You should judge your progress by completing the self assessment exercises. MECHANICS OF SOIS TORSION - TUTORIA 1 You should judge your progress by completing the self assessment exercises. On completion of this tutorial you should be able to do the following. erive the torsion

More information

Tuesday, February 11, Chapter 3. Load and Stress Analysis. Dr. Mohammad Suliman Abuhaiba, PE

Tuesday, February 11, Chapter 3. Load and Stress Analysis. Dr. Mohammad Suliman Abuhaiba, PE 1 Chapter 3 Load and Stress Analysis 2 Chapter Outline Equilibrium & Free-Body Diagrams Shear Force and Bending Moments in Beams Singularity Functions Stress Cartesian Stress Components Mohr s Circle for

More information

Chapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd

Chapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd Chapter Objectives To determine the torsional deformation of a perfectly elastic circular shaft. To determine the support reactions when these reactions cannot be determined solely from the moment equilibrium

More information

2. Polar moment of inertia As stated above, the polar second moment of area, J is defined as. Sample copy

2. Polar moment of inertia As stated above, the polar second moment of area, J is defined as. Sample copy GATE PATHSHALA - 91. Polar moment of inertia As stated above, the polar second moment of area, is defined as z π r dr 0 R r π R π D For a solid shaft π (6) QP 0 π d Solid shaft π d Hollow shaft, " ( do

More information

Torsion of Shafts Learning objectives

Torsion of Shafts Learning objectives Torsion of Shafts Shafts are structural members with length significantly greater than the largest cross-sectional dimension used in transmitting torque from one plane to another. Learning objectives Understand

More information

WORCESTER POLYTECHNIC INSTITUTE

WORCESTER POLYTECHNIC INSTITUTE WORCESTER POLYTECHNIC INSTITUTE MECHANICAL ENGINEERING DEPARTMENT STRESS ANALYSIS ES-2502, C 2012 Lecture 17: 10 February 2012 General information Instructor: Cosme Furlong HL-151 (508) 831-5126 cfurlong@wpi.edu

More information

SRI CHANDRASEKHARENDRA SARASWATHI VISWA MAHAVIDHYALAYA

SRI CHANDRASEKHARENDRA SARASWATHI VISWA MAHAVIDHYALAYA SRI CHANDRASEKHARENDRA SARASWATHI VISWA MAHAVIDHYALAYA (Declared as Deemed-to-be University under Section 3 of the UGC Act, 1956, Vide notification No.F.9.9/92-U-3 dated 26 th May 1993 of the Govt. of

More information

Downloaded from Downloaded from / 1

Downloaded from   Downloaded from   / 1 PURWANCHAL UNIVERSITY III SEMESTER FINAL EXAMINATION-2002 LEVEL : B. E. (Civil) SUBJECT: BEG256CI, Strength of Material Full Marks: 80 TIME: 03:00 hrs Pass marks: 32 Candidates are required to give their

More information

3 Hours/100 Marks Seat No.

3 Hours/100 Marks Seat No. *17304* 17304 14115 3 Hours/100 Marks Seat No. Instructions : (1) All questions are compulsory. (2) Illustrate your answers with neat sketches wherever necessary. (3) Figures to the right indicate full

More information

Torsion of shafts with circular symmetry

Torsion of shafts with circular symmetry orsion of shafts with circular symmetry Introduction Consider a uniform bar which is subject to a torque, eg through the action of two forces F separated by distance d, hence Fd orsion is the resultant

More information

UNIT-I STRESS, STRAIN. 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2

UNIT-I STRESS, STRAIN. 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2 UNIT-I STRESS, STRAIN 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2 Young s modulus E= 2 x10 5 N/mm 2 Area1=900mm 2 Area2=400mm 2 Area3=625mm

More information

M. Vable Mechanics of Materials: Chapter 5. Torsion of Shafts

M. Vable Mechanics of Materials: Chapter 5. Torsion of Shafts Torsion of Shafts Shafts are structural members with length significantly greater than the largest cross-sectional dimension used in transmitting torque from one plane to another. Learning objectives Understand

More information

MARKS DISTRIBUTION AS PER CHAPTER (QUESTION ASKED IN GTU EXAM) Name Of Chapter. Applications of. Friction. Centroid & Moment.

MARKS DISTRIBUTION AS PER CHAPTER (QUESTION ASKED IN GTU EXAM) Name Of Chapter. Applications of. Friction. Centroid & Moment. Introduction Fundamentals of statics Applications of fundamentals of statics Friction Centroid & Moment of inertia Simple Stresses & Strain Stresses in Beam Torsion Principle Stresses DEPARTMENT OF CIVIL

More information

Solution: The strain in the bar is: ANS: E =6.37 GPa Poison s ration for the material is:

Solution: The strain in the bar is: ANS: E =6.37 GPa Poison s ration for the material is: Problem 10.4 A prismatic bar with length L 6m and a circular cross section with diameter D 0.0 m is subjected to 0-kN compressive forces at its ends. The length and diameter of the deformed bar are measured

More information

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric

More information

R13. II B. Tech I Semester Regular Examinations, Jan MECHANICS OF SOLIDS (Com. to ME, AME, AE, MTE) PART-A

R13. II B. Tech I Semester Regular Examinations, Jan MECHANICS OF SOLIDS (Com. to ME, AME, AE, MTE) PART-A SET - 1 II B. Tech I Semester Regular Examinations, Jan - 2015 MECHANICS OF SOLIDS (Com. to ME, AME, AE, MTE) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts (Part-A and Part-B)

More information

PES Institute of Technology

PES Institute of Technology PES Institute of Technology Bangalore south campus, Bangalore-5460100 Department of Mechanical Engineering Faculty name : Madhu M Date: 29/06/2012 SEM : 3 rd A SEC Subject : MECHANICS OF MATERIALS Subject

More information

Strength of Materials Prof S. K. Bhattacharya Department of Civil Engineering Indian Institute of Technology, Kharagpur Lecture - 18 Torsion - I

Strength of Materials Prof S. K. Bhattacharya Department of Civil Engineering Indian Institute of Technology, Kharagpur Lecture - 18 Torsion - I Strength of Materials Prof S. K. Bhattacharya Department of Civil Engineering Indian Institute of Technology, Kharagpur Lecture - 18 Torsion - I Welcome to the first lesson of Module 4 which is on Torsion

More information

SN QUESTION YEAR MARK 1. State and prove the relationship between shearing stress and rate of change of bending moment at a section in a loaded beam.

SN QUESTION YEAR MARK 1. State and prove the relationship between shearing stress and rate of change of bending moment at a section in a loaded beam. ALPHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING MECHANICS OF SOLIDS (21000) ASSIGNMENT 1 SIMPLE STRESSES AND STRAINS SN QUESTION YEAR MARK 1 State and prove the relationship

More information

ROTATING RING. Volume of small element = Rdθbt if weight density of ring = ρ weight of small element = ρrbtdθ. Figure 1 Rotating ring

ROTATING RING. Volume of small element = Rdθbt if weight density of ring = ρ weight of small element = ρrbtdθ. Figure 1 Rotating ring ROTATIONAL STRESSES INTRODUCTION High centrifugal forces are developed in machine components rotating at a high angular speed of the order of 100 to 500 revolutions per second (rps). High centrifugal force

More information

SECTION A. 8 kn/m. C 3 m 3m

SECTION A. 8 kn/m. C 3 m 3m SECTION Question 1 150 m 40 kn 5 kn 8 kn/m C 3 m 3m D 50 ll dimensions in mm 15 15 Figure Q1(a) Figure Q1(b) The horizontal beam CD shown in Figure Q1(a) has a uniform cross-section as shown in Figure

More information

Members Subjected to Torsional Loads

Members Subjected to Torsional Loads Members Subjected to Torsional Loads Torsion of circular shafts Definition of Torsion: Consider a shaft rigidly clamped at one end and twisted at the other end by a torque T = F.d applied in a plane perpendicular

More information

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV UNIT I STRESS, STRAIN DEFORMATION OF SOLIDS PART A (2 MARKS)

More information

Sample Question Paper

Sample Question Paper Scheme I Sample Question Paper Program Name : Mechanical Engineering Program Group Program Code : AE/ME/PG/PT/FG Semester : Third Course Title : Strength of Materials Marks : 70 Time: 3 Hrs. Instructions:

More information

BE Semester- I ( ) Question Bank (MECHANICS OF SOLIDS)

BE Semester- I ( ) Question Bank (MECHANICS OF SOLIDS) BE Semester- I ( ) Question Bank (MECHANICS OF SOLIDS) All questions carry equal marks(10 marks) Q.1 (a) Write the SI units of following quantities and also mention whether it is scalar or vector: (i)

More information

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture twenty one concrete construction: Copyright Kirk Martini shear & deflection Concrete Shear 1 Shear in Concrete

More information

2. Determine the deflection at C of the beam given in fig below. Use principal of virtual work. W L/2 B A L C

2. Determine the deflection at C of the beam given in fig below. Use principal of virtual work. W L/2 B A L C CE-1259, Strength of Materials UNIT I STRESS, STRAIN DEFORMATION OF SOLIDS Part -A 1. Define strain energy density. 2. State Maxwell s reciprocal theorem. 3. Define proof resilience. 4. State Castigliano

More information

18.Define the term modulus of resilience. May/June Define Principal Stress. 20. Define Hydrostatic Pressure.

18.Define the term modulus of resilience. May/June Define Principal Stress. 20. Define Hydrostatic Pressure. CE6306 STREGNTH OF MATERIALS Question Bank Unit-I STRESS, STRAIN, DEFORMATION OF SOLIDS PART-A 1. Define Poison s Ratio May/June 2009 2. What is thermal stress? May/June 2009 3. Estimate the load carried

More information

2014 MECHANICS OF MATERIALS

2014 MECHANICS OF MATERIALS R10 SET - 1 II. Tech I Semester Regular Examinations, March 2014 MEHNIS OF MTERILS (ivil Engineering) Time: 3 hours Max. Marks: 75 nswer any FIVE Questions ll Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~~

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad -00 04 CIVIL ENGINEERING QUESTION BANK Course Name : STRENGTH OF MATERIALS II Course Code : A404 Class : II B. Tech II Semester Section

More information

Chapter 3. Load and Stress Analysis. Lecture Slides

Chapter 3. Load and Stress Analysis. Lecture Slides Lecture Slides Chapter 3 Load and Stress Analysis 2015 by McGraw Hill Education. This is proprietary material solely for authorized instructor use. Not authorized for sale or distribution in any manner.

More information

Only for Reference Page 1 of 18

Only for Reference  Page 1 of 18 Only for Reference www.civilpddc2013.weebly.com Page 1 of 18 Seat No.: Enrolment No. GUJARAT TECHNOLOGICAL UNIVERSITY PDDC - SEMESTER II EXAMINATION WINTER 2013 Subject Code: X20603 Date: 26-12-2013 Subject

More information

NAME: Given Formulae: Law of Cosines: Law of Sines:

NAME: Given Formulae: Law of Cosines: Law of Sines: NME: Given Formulae: Law of Cosines: EXM 3 PST PROBLEMS (LESSONS 21 TO 28) 100 points Thursday, November 16, 2017, 7pm to 9:30, Room 200 You are allowed to use a calculator and drawing equipment, only.

More information

4. SHAFTS. A shaft is an element used to transmit power and torque, and it can support

4. SHAFTS. A shaft is an element used to transmit power and torque, and it can support 4. SHAFTS A shaft is an element used to transmit power and torque, and it can support reverse bending (fatigue). Most shafts have circular cross sections, either solid or tubular. The difference between

More information

Mechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002

Mechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002 student personal identification (ID) number on each sheet. Do not write your name on any sheet. #1. A homogeneous, isotropic, linear elastic bar has rectangular cross sectional area A, modulus of elasticity

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS GE SI CHAPTER 3 MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David F. Mazurek Torsion Lecture Notes: J. Walt Oler Texas Tech University Torsional Loads on Circular Shafts

More information

Direct and Shear Stress

Direct and Shear Stress Direct and Shear Stress 1 Direct & Shear Stress When a body is pulled by a tensile force or crushed by a compressive force, the loading is said to be direct. Direct stresses are also found to arise when

More information

SSC-JE MAINS ONLINE TEST SERIES / CIVIL ENGINEERING SOM + TOS

SSC-JE MAINS ONLINE TEST SERIES / CIVIL ENGINEERING SOM + TOS SSC-JE MAINS ONLINE TEST SERIES / CIVIL ENGINEERING SOM + TOS Time Allowed:2 Hours Maximum Marks: 300 Attention: 1. Paper consists of Part A (Civil & Structural) Part B (Electrical) and Part C (Mechanical)

More information

Mechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection

Mechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection Mechanics of Materials II Chapter III A review of the fundamental formulation of stress, strain, and deflection Outline Introduction Assumtions and limitations Axial loading Torsion of circular shafts

More information

2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at A and supported at B by rod (1). What is the axial force in rod (1)?

2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at A and supported at B by rod (1). What is the axial force in rod (1)? IDE 110 S08 Test 1 Name: 1. Determine the internal axial forces in segments (1), (2) and (3). (a) N 1 = kn (b) N 2 = kn (c) N 3 = kn 2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at

More information

PERIYAR CENTENARY POLYTECHNIC COLLEGE PERIYAR NAGAR - VALLAM THANJAVUR. DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK

PERIYAR CENTENARY POLYTECHNIC COLLEGE PERIYAR NAGAR - VALLAM THANJAVUR. DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK PERIYAR CENTENARY POLYTECHNIC COLLEGE PERIYAR NAGAR - VALLAM - 613 403 - THANJAVUR. DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Sub : Strength of Materials Year / Sem: II / III Sub Code : MEB 310

More information

and F NAME: ME rd Sample Final Exam PROBLEM 1 (25 points) Prob. 1 questions are all or nothing. PROBLEM 1A. (5 points)

and F NAME: ME rd Sample Final Exam PROBLEM 1 (25 points) Prob. 1 questions are all or nothing. PROBLEM 1A. (5 points) ME 270 3 rd Sample inal Exam PROBLEM 1 (25 points) Prob. 1 questions are all or nothing. PROBLEM 1A. (5 points) IND: In your own words, please state Newton s Laws: 1 st Law = 2 nd Law = 3 rd Law = PROBLEM

More information

Lab Exercise #3: Torsion

Lab Exercise #3: Torsion Lab Exercise #3: Pre-lab assignment: Yes No Goals: 1. To evaluate the equations of angular displacement, shear stress, and shear strain for a shaft undergoing torsional stress. Principles: testing of round

More information

N = Shear stress / Shear strain

N = Shear stress / Shear strain UNIT - I 1. What is meant by factor of safety? [A/M-15] It is the ratio between ultimate stress to the working stress. Factor of safety = Ultimate stress Permissible stress 2. Define Resilience. [A/M-15]

More information

This chapter is devoted to the study of torsion and of the stresses and deformations it causes. In the jet engine shown here, the central shaft links

This chapter is devoted to the study of torsion and of the stresses and deformations it causes. In the jet engine shown here, the central shaft links his chapter is devoted to the study of torsion and of the stresses and deformations it causes. In the jet engine shown here, the central shaft links the components of the engine to develop the thrust that

More information

UNIT 1 STRESS STRAIN AND DEFORMATION OF SOLIDS, STATES OF STRESS 1. Define stress. When an external force acts on a body, it undergoes deformation.

UNIT 1 STRESS STRAIN AND DEFORMATION OF SOLIDS, STATES OF STRESS 1. Define stress. When an external force acts on a body, it undergoes deformation. UNIT 1 STRESS STRAIN AND DEFORMATION OF SOLIDS, STATES OF STRESS 1. Define stress. When an external force acts on a body, it undergoes deformation. At the same time the body resists deformation. The magnitude

More information

OUTCOME 1 - TUTORIAL 3 BENDING MOMENTS. You should judge your progress by completing the self assessment exercises. CONTENTS

OUTCOME 1 - TUTORIAL 3 BENDING MOMENTS. You should judge your progress by completing the self assessment exercises. CONTENTS Unit 2: Unit code: QCF Level: 4 Credit value: 15 Engineering Science L/601/1404 OUTCOME 1 - TUTORIAL 3 BENDING MOMENTS 1. Be able to determine the behavioural characteristics of elements of static engineering

More information

Further Linear Elasticity

Further Linear Elasticity Torsion of cylindrical bodies Further Linear Elasticity Problem Sheet # 1. Consider a cylindrical body of length L, the ends of which are subjected to distributions of tractions that are statically equivalent

More information

ME Final Exam. PROBLEM NO. 4 Part A (2 points max.) M (x) y. z (neutral axis) beam cross-sec+on. 20 kip ft. 0.2 ft. 10 ft. 0.1 ft.

ME Final Exam. PROBLEM NO. 4 Part A (2 points max.) M (x) y. z (neutral axis) beam cross-sec+on. 20 kip ft. 0.2 ft. 10 ft. 0.1 ft. ME 323 - Final Exam Name December 15, 2015 Instructor (circle) PROEM NO. 4 Part A (2 points max.) Krousgrill 11:30AM-12:20PM Ghosh 2:30-3:20PM Gonzalez 12:30-1:20PM Zhao 4:30-5:20PM M (x) y 20 kip ft 0.2

More information

PROBLEM 3.3 ( )(45 10 ) T 5.17 kn m. A c c. 2 J c, (2)( ) 2 ( ) mm ( )

PROBLEM 3.3 ( )(45 10 ) T 5.17 kn m. A c c. 2 J c, (2)( ) 2 ( ) mm ( ) 0 mm PROEM..4 m 45 mm (a) Determine the torque that causes a maximum shearing stress of 45 MPa in the hollow cylindrical steel shaft shown. Determine the maximum shearing stress caused by the same torque

More information

[5] Stress and Strain

[5] Stress and Strain [5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law

More information

Engineering Science OUTCOME 1 - TUTORIAL 4 COLUMNS

Engineering Science OUTCOME 1 - TUTORIAL 4 COLUMNS Unit 2: Unit code: QCF Level: Credit value: 15 Engineering Science L/601/10 OUTCOME 1 - TUTORIAL COLUMNS 1. Be able to determine the behavioural characteristics of elements of static engineering systems

More information

2012 MECHANICS OF SOLIDS

2012 MECHANICS OF SOLIDS R10 SET - 1 II B.Tech II Semester, Regular Examinations, April 2012 MECHANICS OF SOLIDS (Com. to ME, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~

More information

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work.

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work. It is most beneficial to you to write this mock final exam UNDER EXAM CONDITIONS. This means: Complete the exam in 3 hours. Work on your own. Keep your textbook closed. Attempt every question. After the

More information

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN EDEXCEL NATIONAL CERTIFICATE/DIPLOMA SCIENCE FOR TECHNICIANS OUTCOME 1 - STATIC AND DYNAMIC FORCES TUTORIAL 3 STRESS AND STRAIN 1 Static and dynamic forces Forces: definitions of: matter, mass, weight,

More information

Determine the resultant internal loadings acting on the cross section at C of the beam shown in Fig. 1 4a.

Determine the resultant internal loadings acting on the cross section at C of the beam shown in Fig. 1 4a. E X M P L E 1.1 Determine the resultant internal loadings acting on the cross section at of the beam shown in Fig. 1 a. 70 N/m m 6 m Fig. 1 Support Reactions. This problem can be solved in the most direct

More information

Advanced Structural Analysis EGF Section Properties and Bending

Advanced Structural Analysis EGF Section Properties and Bending Advanced Structural Analysis EGF316 3. Section Properties and Bending 3.1 Loads in beams When we analyse beams, we need to consider various types of loads acting on them, for example, axial forces, shear

More information

STRESS, STRAIN AND DEFORMATION OF SOLIDS

STRESS, STRAIN AND DEFORMATION OF SOLIDS VELAMMAL COLLEGE OF ENGINEERING AND TECHNOLOGY, MADURAI 625009 DEPARTMENT OF CIVIL ENGINEERING CE8301 STRENGTH OF MATERIALS I -------------------------------------------------------------------------------------------------------------------------------

More information

STRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains

STRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains STRENGTH OF MATERIALS-I Unit-1 Simple stresses and strains 1. What is the Principle of surveying 2. Define Magnetic, True & Arbitrary Meridians. 3. Mention different types of chains 4. Differentiate between

More information

CIVIL DEPARTMENT MECHANICS OF STRUCTURES- ASSIGNMENT NO 1. Brach: CE YEAR:

CIVIL DEPARTMENT MECHANICS OF STRUCTURES- ASSIGNMENT NO 1. Brach: CE YEAR: MECHANICS OF STRUCTURES- ASSIGNMENT NO 1 SEMESTER: V 1) Find the least moment of Inertia about the centroidal axes X-X and Y-Y of an unequal angle section 125 mm 75 mm 10 mm as shown in figure 2) Determine

More information

This equation of motion may be solved either by differential equation method or by graphical method as discussed below:

This equation of motion may be solved either by differential equation method or by graphical method as discussed below: 2.15. Frequency of Under Damped Forced Vibrations Consider a system consisting of spring, mass and damper as shown in Fig. 22. Let the system is acted upon by an external periodic (i.e. simple harmonic)

More information

BME 207 Introduction to Biomechanics Spring 2017

BME 207 Introduction to Biomechanics Spring 2017 April 7, 2017 UNIVERSITY OF RHODE ISAND Department of Electrical, Computer and Biomedical Engineering BE 207 Introduction to Biomechanics Spring 2017 Homework 7 Problem 14.3 in the textbook. In addition

More information

CHAPTER 3 THE EFFECTS OF FORCES ON MATERIALS

CHAPTER 3 THE EFFECTS OF FORCES ON MATERIALS CHAPTER THE EFFECTS OF FORCES ON MATERIALS EXERCISE 1, Page 50 1. A rectangular bar having a cross-sectional area of 80 mm has a tensile force of 0 kn applied to it. Determine the stress in the bar. Stress

More information

UNIT-I Introduction & Plane Stress and Plane Strain Analysis

UNIT-I Introduction & Plane Stress and Plane Strain Analysis SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY:: PUTTUR (AUTONOMOUS) Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : Advanced Solid Mechanics (18CE1002) Year

More information

ME325 EXAM I (Sample)

ME325 EXAM I (Sample) ME35 EXAM I (Sample) NAME: NOTE: COSED BOOK, COSED NOTES. ONY A SINGE 8.5x" ORMUA SHEET IS AOWED. ADDITIONA INORMATION IS AVAIABE ON THE AST PAGE O THIS EXAM. DO YOUR WORK ON THE EXAM ONY (NO SCRATCH PAPER

More information

D : SOLID MECHANICS. Q. 1 Q. 9 carry one mark each.

D : SOLID MECHANICS. Q. 1 Q. 9 carry one mark each. GTE 2016 Q. 1 Q. 9 carry one mark each. D : SOLID MECHNICS Q.1 single degree of freedom vibrating system has mass of 5 kg, stiffness of 500 N/m and damping coefficient of 100 N-s/m. To make the system

More information

8. Combined Loadings

8. Combined Loadings CHAPTER OBJECTIVES qanalyze the stress developed in thin-walled pressure vessels qreview the stress analysis developed in previous chapters regarding axial load, torsion, bending and shear qdiscuss the

More information

CHAPTER 6 TORSION. its inner diameter d d / 2. = mm = = mm. π (122.16) = mm 2

CHAPTER 6 TORSION. its inner diameter d d / 2. = mm = = mm. π (122.16) = mm 2 CHAPTER 6 TORSION Prolem. A olid circular haft i to tranmit 00 kw at 00 r.p.m. If the hear tre i not to exceed 80 N/mm, find the diameter of the haft. What percentage in aving would e otained if thi haft

More information

CE6306 STRENGTH OF MATERIALS TWO MARK QUESTIONS WITH ANSWERS ACADEMIC YEAR

CE6306 STRENGTH OF MATERIALS TWO MARK QUESTIONS WITH ANSWERS ACADEMIC YEAR CE6306 STRENGTH OF MATERIALS TWO MARK QUESTIONS WITH ANSWERS ACADEMIC YEAR 2014-2015 UNIT - 1 STRESS, STRAIN AND DEFORMATION OF SOLIDS PART- A 1. Define tensile stress and tensile strain. The stress induced

More information

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering Mechanics Of Solids Suraj kr. Ray (surajjj2445@gmail.com) Department of Civil Engineering 1 Mechanics of Solids is a branch of applied mechanics that deals with the behaviour of solid bodies subjected

More information

IDE 110 Mechanics of Materials Spring 2006 Final Examination FOR GRADING ONLY

IDE 110 Mechanics of Materials Spring 2006 Final Examination FOR GRADING ONLY Spring 2006 Final Examination STUDENT S NAME (please print) STUDENT S SIGNATURE STUDENT NUMBER IDE 110 CLASS SECTION INSTRUCTOR S NAME Do not turn this page until instructed to start. Write your name on

More information

The University of Melbourne Engineering Mechanics

The University of Melbourne Engineering Mechanics The University of Melbourne 436-291 Engineering Mechanics Tutorial Four Poisson s Ratio and Axial Loading Part A (Introductory) 1. (Problem 9-22 from Hibbeler - Statics and Mechanics of Materials) A short

More information

Semester: BE 3 rd Subject :Mechanics of Solids ( ) Year: Faculty: Mr. Rohan S. Kariya. Tutorial 1

Semester: BE 3 rd Subject :Mechanics of Solids ( ) Year: Faculty: Mr. Rohan S. Kariya. Tutorial 1 Semester: BE 3 rd Subject :Mechanics of Solids (2130003) Year: 2018-19 Faculty: Mr. Rohan S. Kariya Class: MA Tutorial 1 1 Define force and explain different type of force system with figures. 2 Explain

More information

COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 3013 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6

COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 3013 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6 COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 0 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6 TIME SCHEDULE Module Topics Period Moment of forces Support reactions Centre

More information

Aluminum shell. Brass core. 40 in

Aluminum shell. Brass core. 40 in PROBLEM #1 (22 points) A solid brass core is connected to a hollow rod made of aluminum. Both are attached at each end to a rigid plate as shown in Fig. 1. The moduli of aluminum and brass are EA=11,000

More information

FIXED BEAMS IN BENDING

FIXED BEAMS IN BENDING FIXED BEAMS IN BENDING INTRODUCTION Fixed or built-in beams are commonly used in building construction because they possess high rigidity in comparison to simply supported beams. When a simply supported

More information

Russell C. Hibbeler. Chapter 1: Stress

Russell C. Hibbeler. Chapter 1: Stress Russell C. Hibbeler Chapter 1: Stress Introduction Mechanics of materials is a study of the relationship between the external loads on a body and the intensity of the internal loads within the body. This

More information

Shafts: Torsion of Circular Shafts Reading: Crandall, Dahl and Lardner 6.2, 6.3

Shafts: Torsion of Circular Shafts Reading: Crandall, Dahl and Lardner 6.2, 6.3 M9 Shafts: Torsion of Circular Shafts Reading: Crandall, Dahl and Lardner 6., 6.3 A shaft is a structural member which is long and slender and subject to a torque (moment) acting about its long axis. We

More information

TOPIC D: ROTATION EXAMPLES SPRING 2018

TOPIC D: ROTATION EXAMPLES SPRING 2018 TOPIC D: ROTATION EXAMPLES SPRING 018 Q1. A car accelerates uniformly from rest to 80 km hr 1 in 6 s. The wheels have a radius of 30 cm. What is the angular acceleration of the wheels? Q. The University

More information

Samantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2

Samantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2 Samantha Ramirez, MSE Stress The intensity of the internal force acting on a specific plane (area) passing through a point. Δ ΔA Δ z Δ 1 2 ΔA Δ x Δ y ΔA is an infinitesimal size area with a uniform force

More information

LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR.

LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR. LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR. IBIKUNLE ROTIMI ADEDAYO SIMPLE HARMONIC MOTION. Introduction Consider

More information

Mechanics of Structure

Mechanics of Structure S.Y. Diploma : Sem. III [CE/CS/CR/CV] Mechanics of Structure Time: Hrs.] Prelim Question Paper Solution [Marks : 70 Q.1(a) Attempt any SIX of the following. [1] Q.1(a) Define moment of Inertia. State MI

More information