U LED modules, converters and systems GENERAL ILLUMINATION. Umodule SPOT P330-3 EM umodule SPOT PHASED OUT NTC NTC LED + LED + LED EM LED EM

Transcription

1 Product description Spotlights Downlights High-flux LED module Narrow colour temperature tolerance band Lifetime up to 5, hours Compact design Excellent thermal management NTC for temperature control High-power LED in chip-on-board technololgy Beam characteristic: 4 Uniform distribution of light Fixing holes for M3 screws Connection: Cable 3 mm Built-in LED module Cooling required Technical data Beam characteristic 4 Ambient temperature ta C Typ. tc point 65 C Weight.5 kg Risk group (EN 6247:28) È Standards, page 2 Colour temperatures and tolerances, page 6 Umodule SPOT P33-3 EM umodule SPOT NTC NTC LED + LED + LED EM LED EM Minimal reflector diameter 2 Maximum reflector diameter.65 Ø d Ø typ. Ordering data Colour temperature Article number 3, K LED P33-3 EM 3K 47x , K LED P33-3 EM 4K 47x Packaging: 2 pieces/packaging, 36 pieces/carton Specific technical data Photometric Typ. luminous flux Typ. luminous flux Typ. luminous flux Typ. forward voltage 23 Power consumption Typ. efficacy Colour rendering index code at 35 ma 234 at,5 ma 234 at,4 ma 234 module CRI Normal operation LED P33-3 EM 3K 47x44 83/4x9 2, lm 2,5 lm 28.8 V 3.2 W 69 lm/w > 8 LED P33-3 EM 4K 47x44 84/4x9 2,22 lm 2,76 lm 28.8 V 3.2 W 76 lm/w > 8 Emergency operation 35 ma LED P33-3 EM 3K 47x44 83/4x9 5 lm 6,2 V 2.2 W 69 lm/w > 8 LED P33-3 EM 4K 47x44 84/4x9 6 lm 6,2 V 2.2 W 76 lm/w > 8 All values for ta = 25 C, tc = 65 C. If the maximum temperature limits are exceeded, the life of the module will be greatly reduced or the module may be damaged. The temperature of the umodule SPOT at the tc point in the thermally stable state by mean of a temperature sensor or temperature-sensitive sticker as per EN For the precise position of the tc point see the drawing above. 2 At tc = 65 C 3 Tolerance range for optical and electrical data: ±5 %. 4 Max. permissible surge current: 3 A, duration max. µs.

2 Converter matrix Umodule SPOT P33-3 EM in emergency operation 2 W BASIC screw-fix 2 W BASIC clip-fix Converter for emergency operation 2 W ST screw-fix 2 W ST clip-fix 2 W PRO EZ-3 screw-fix 2 W PRO EZ-3 clip-fix Article number Assignable converter Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Umodule SPOT P33-3 EM Wiring diagram converter + Emergency device Uconverter Product description Housing for LED modul Diameter: 5 mm Converter matrix Umodule SPOT 33-3 EM REMOTE LCI NTC LCI 5/5 T LCI 55/4 T2 ACCES- SORIES LCAI 5/5 T2 LCAI 55/4 T2 TALEXXaccessory Cover Spot LCI 5/5 R LCI 55/4 R IN-BUILT LCI LCAI 5/5 R LCAI 55/4 R Art. No Assignable converter Assignable converter Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. LED P33-3 EM 3K 47x LED P33-3 EM 4K 47x Wiring Cable: AWG24; length 3 mm pin function + (LED) - (LED) + (EM) - (EM) NTC (LED) NTC (LED) colour red black red black grey grey Ordering data Article number P 33-3 EM LED cover white D5 LES 23 mm Packaging: 2 pieces/packaging, 4 pieces/carton 2

3 Standards EN 623 EN 6247 Photometric code Key for photometric code, e. g. 83 / 559 st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit Lumen maintanance after 25% Code CRI McAdams after of the lifetime (max.6h) Colour temperature in McAdams 25% of the Code Remaining lumen Kelvin x initial lifetime 7 7 % (max.6h) 8 8 % % Thermal design and heat sink The rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule SPOT will be greatly reduced or the umodule SPOT may be destroyed. Therefore the umodule SPOT P33-3 EM needs to be mounted onto a heat sink. Tridonic s excellent thermal design for the umodule SPOT products provides the lowest thermal resistance and therefore allowing new compact designs without sacrificing quality, safety and life time. tc point, ambient temperature and lifetime The temperature at tc reference point is crucial for the light output and life time of a u product. For umodule SPOT P33-3 EM a tc temperature of 65 C has to be complied in order to achieve an optimum between heat sink requirements, light output and life time. Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application. Mounting instruction umodule SPOT from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws with plastic washer. The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease. None of the components of the umodule SPOT (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses. EOS/ESD safety guidelines The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: Temperature control An NTC resistor is on the board of the umodule SPOT P33-3 EM to control the tc temperature during the operation. Exact position see drawing on page. The details of the 22 kω NTC (order number B5743V2223J62) you can find in the data sheet of the manufacturer AVX (Nr. NB2QØØ224). T Typical heat sink surface Umodule SPOT P33-3 EM,,5 ma ta tc Rth, hs-a 25 C 65 C.34 K/W 3 C 65 C.5 K/W 4 C 65 C.77 K/W 5 C 65 C.4 K/W Umodule SPOT P33-3 EM,,4 ma ta tc Rth, hs-a 25 C 65 C.96 K/W 3 C 65 C.82 K/W 4 C 65 C.54 K/W 5 C 65 C.25 K/W R 25 = 22 kω, B 25 / = 4,5 K R T / R 25 α 25 C. 4.8 % / K 3 C % / K 35 C % / K 4 C % / K 45 C % / K 5 C % / K 55 C % / K 6 C % / K 65 C % / K 7 C % / K 75 C % / K 8 C % / K 85 C % / K Notes The actual cooling surface can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule SPOT and heat sink with heat-conducting paste or heat conducting adhesive film is absolutely necessary. 3

4 Thermal behaviour storage temperature C operating temperature C tc max. (at typ. current) 85 C Normal operation Pin &2 Emergency operation Pin 3&4 If [ma] Matrix temperature f(soldering time) for the modules Temperature Max. time Max. time without heat sink with optimized heat sink 33 C 5 s 34 C 2 s 35 C s 36 C 5 s 5 s 37 C 3 s 2 s 38 C 2 s s 39 C s 5 s The values apply for soldering without heat sink. To reduce the duration of soldering it is recommended to pre-heat the module at ta max., e.g. on a plate. Electrical supply/choice of converter umodule SPOT from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a converter which complies with the relevant standards. The use of u converters from Tridonic in combination with umodule SPOT guarantees the necessary protection for safe and reliable operation. If a converter other than Tridonic uconverter is used, it must provide the following protection: Short-circuit protection Overload protection Overtemperature protection umodule SPOT P33-3 EM must be supplied by a constant current converter. Operation with a constant voltage converter will lead to an irreversible damage of the module. Wrong polarity can damage the umodule SPOT P33-3 EM. If [ma] Lifetime tc temperature in C luminous flux in % lifetime in h 8 6, , 5 32, 8 44, , 5, 8 32, , 5 9, 8 25, , 5 8, 4

5 Relative forward voltage and relative luminous flux in emergency operation,5,5 rel. voltage [a. u.] rel. luminous flux [a.u.],,5,,95, Relative forward voltage at tc = 65 C,8,6,4,2,,8,6,4, Relative luminous flux at tc = 65 C The diagrams based on statistic values. The real values can be different. rel. voltage [a.u.] rel. luminous flux [a.u.],4,3,2,,99,98, ,4,2,,8,6,4,2,98,96, ,

6 Relative forward voltage and relative luminous flux in normal operation rel. voltage [a. u.] rel. luminous flux [a. u.] Optical characteristics Umodule SPOT P33-2 The optical design of the umodule SPOT product line ensures optimum homogenity for the light distribution. Umodule SPOT P33-3 EM 4 : Light distribution relative intensity Iv/Iv,max,,5,,95,9,85, Relative forward voltage at tc = 65 C,4,2,,8,6,4, Relative luminous flux at tc = 65 C rel. voltage [a.u.] rel. luminous flux [a.u.],5,4,3,2,,99,98, ,4,2,,8,6,4,2,98,96, ,

7 Coordinates and tolerances according to CIE 964 The specified colour coordinates are measured by a current impulse of,5 ma and a duration of ms. The ambient temperature of the measurement is ta = 25 C. The measurement tolerance of the colour coordinates are ±.. 3, K x y Centre,446,399,42,45,4,45,4,395,39,385,38,425,43,435,44,445 MacAdam ellipse: 4SDCM 4, K x y Centre,386, MacAdam ellipse: 4SDCM,45.39, ,46.4, norm. intensity [%] norm. intensity [%] wave length [nm] wave length [nm] 7