Connections Standard. Description

Size: px
Start display at page:

Download "Connections Standard. Description"

Transcription

1 Section Convectors Description Connections Standard without built-in valve or version with built-in valve Air vent, Drain Fixing Pressure versions, Fittings, Surface finishes, Special versions Heat output Technical data Lengths: mm Heights: 0 0 mm Depths: mm Convector WVO With shield for radiated heat on rear Lengths: mm Heights: 0 0 mm Depths: mm Universal convector LCR Ideal for stocking Lengths: mm Heights: 0 0 mm Depths: mm Subject to technical change without notice. Technical Documentation 0-N -

2 Description Model C C....../ Standard without built-in valve Explanation model code C : convector C : convector... : height in cm... : height in cm... : number of tubes carrying water... : number of tubes carrying water / : with fins at rear Example C/ C : convector : height cm : tubes carrying water / : with fins at rear Model C......V C....../V Version with built-in valve V: with built-in valve 0 General Form and function combine in modern architecture in a harmonious manner. Arbonia convectors support the architect and client in this harmony: the clear emphasis of the horizontal line, clean side connections and the fine structure of the cover permit open installation. High heat output from small dimensions and the diverse range round off the attractive image of this room heater. Convectors C without fins at the rear are GUV-compliant in the special version with top grill. Range available depths: - Without fins at rear:,, and mm - With fins at rear:,, and mm heights: 0, 0, 0 and 0 mm Length: mm: steps: 00 mm mm: steps: 0 mm (manufacturing tolerance: ± mm, measured at C) - Maximum length mm, as a function of weight empty -tube connections Rear lugs for depth mm ) Not in all colours Special versions -tube connections Version with built-in valve Built-in air vent with rotating outlet High-pressure version 0 bar (000 kpa) Top grill (GUV-compliant) Screwed feet Angled or curved version Rear lugs for depth mm Fixing as bench: - For convectors with depth mm - Order brackets as accessories Surface finishes AllFinish in pure white (AF) RAL 00 standard version AllFinish in traffic white (AF) RAL 0 Primed in cream-white (ET) Primed in cream-white and packed in plastic sheet (EF) ColorFinish in standard colour (CF) SuperFinish in colour of choice (SF) ) Textured paint after priming - In white (SL) - In colour of choice (KL) ) Clear lacquer (TF) Hot-dip galvanised outside, for wet rooms (swimming pools, cellar rooms for washing etc.), does not apply for damp rooms (bathroom and WC) - Without paint finish (ZN) - With textured paint in white (ZL) - With textured paint in colour of choice (ZK) ) Anti-microbial coating (AM) All finishes are baked at 0 C. For detailed information see "Colour Fashion of the Arbonia Radiators". - Technical Documentation 0-N Subject to technical change without notice.

3 Description Operating conditions For closed water heating systems in accordance with DIN 0 and water quality in accordance with VDI Can be used in conventional and low temperature areas Can be used for district heating and high-rise buildings (high permissible operating pressure) Not suitable for steam-based heating systems Length expansion: 0, mm/m at a temperature difference of K Properties of relevance to operation Minimum water flow rate The minimum water flow rate must not be less than 0 % of the standard water flow rate in accordance with EN to avoid a reduction in the heat output. This applies both to connection on same end and on opposite ends. Pressure drop Δp Δp = ζ x ρ/ x w Standardversion High-pressure version Operating pressure [bar (kpa)],0 (00) 0,0 (000) Test pressure [bar (kpa)], (0),0 (00) Max. temperature [ C] Δp: Pressure drop [Pa] ζ: Resistance coefficient Zeta [] ρ: Density of the water [kg/m ] w: Water velocity [m/s] The ζ values are given in the connection table and apply for a water velocity of up to m/s. Heat outputs The heat outputs given are determined and registered in accordance with the guidelines in EN : DIN CERTCO registered. RAL tested and registered. Tender text Room heaters with up to five 0 x x, mm steel tubes arranged one behind the other and up to four 0 x x, mm steel tubes arranged one above the other with convector fins and collectors on the ends connected by hidden welds and rounded edges all round with R min = mm. Ready to install with to connection threads on the ends in the collectors for flow and return as well as air vent and drain. Version with permanently fitted top grill (at extra charge) complies with the basic principles for the testing of the health and safety of room heaters (statutory accident insurance). Winner of award from the Institut für Umwelt- und Krankenhaushygiene at Philipps-Universität Marburg for compliance with high hygiene requirements. Priming in accordance with DIN 00 part and powder coating in accordance with DIN 00 part. Pressure and leak tested. Heat output tested and measured in accordance with EN. CE marked. Suitable for closed water heating systems in accordance with DIN 0 and water quality in accordance with VDI. Maximum permissible operating temperature C Max. operating pressure: bar / 00 kpa 0 bar / 000 kpa Suitably packed for transport. 0 Subject to technical change without notice. Technical Documentation 0-N -

4 Connections standard without built-in valve Connection options flow / return Connection system Ord. code ζ value Arrangement Ordering code Connec. size Ordering code Flow Return Dimension drawings -tube, side,0,0 G / G / G / See page Connection dimensions -tube, side -tube, side and bottom,0,0 G / G / G / See page Connection dimensions -tube, side and "Connections dimensions -tube, bottom" -tube, bottom,0,0 -tube, bottom,one behind the other,0,0 G / G / G / G / G / G / -tube, bottom, middle-middle,,0,0 G / vertical underside ) -tube, for valve with dip tube, side, with dip tube Ø mm 0,0,0 G / See page Connection dimensions -tube, bottom See page Connection dimensions -tube, bottom, one behind the other Only possible from C.. See page Connection dimensions -tube, middle See page Connection dimensions -tube -tube, for valve with dip tube, bottom, with dip tube Ø mm 0,0,0 G / See page Connection dimensions -tube -tube, for TKM valve, bottom, with dip tube,0,0 G / See page Connection dimensions -tube 0 ) Maximum length: 00 mm L: recommended position for air vent tapping: Standard baffle; baffle with Ø mm hole; valve with dip tube; TKM valve On models C0, C0/ the connections in arrangement and are only possible in G /. - Technical Documentation 0-N Subject to technical change without notice.

5 Connections standard without built-in valve Connection dimensions -tube, side Height 0 mm ) C C....../ C0/ ) Connection details 0 0 C0 ) C0/ ) 0 0 C0 C0/ 0 0 /" - /" C0 C0/ 0 0 C0 0 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions ) Only G / (for arrangement feature : or ) Subject to technical change without notice. Technical Documentation 0-N -

6 Connections standard without built-in valve Connection dimensions -tube, side Height 0 mm ) C C....../ C/ Connection details 0 0 C C/ 0 0 C C/ 0 0 /" - /" C C/ C 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions - Technical Documentation 0-N Subject to technical change without notice.

7 Connections standard without built-in valve Connection dimensions -tube, side Height 0 mm ) C C....../ C/ Connection details 0 0 C C/ 0 0 C C/ 0 0 /" - /" C C/ 0 0 C 0 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions Subject to technical change without notice. Technical Documentation 0-N -

8 Connections standard without built-in valve Connection dimensions -tube, side Height 0 mm ) C C....../ C/ Connection details 0 0 C C/ 0 0 C C/ 0 0 /" - /" C C/ C 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions - Technical Documentation 0-N Subject to technical change without notice.

9 Connections standard without built-in valve Connections dimensions -tube, bottom Height 0 mm ) C C....../ C0/ Connection details 0 C0 C0/ 0 0 C0 C0/ /" - /" 0 0 C0 C0/ /" 0 0 C0 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions 0 Subject to technical change without notice. Technical Documentation 0-N -

10 Connections standard without built-in valve Connections dimensions -tube, bottom Height 0 mm ) C C....../ C/ Connection details 0 C C/ 0 0 C C/ /" - /" 0 0 C C/ /" C 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions -0 Technical Documentation 0-N Subject to technical change without notice.

11 Connections standard without built-in valve Connections dimensions -tube, bottom Height 0 mm ) C C....../ C/ Connection details 0 C C/ 0 0 C C/ /" - /" 0 0 C C/ /" 0 0 C 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions 0 Subject to technical change without notice. Technical Documentation 0-N -

12 Connections standard without built-in valve Connections dimensions -tube, bottom Height 0 mm ) C C....../ C/ Connection details 0 C C/ 0 0 C C/ /" - /" 0 0 C C/ /" C 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions - Technical Documentation 0-N Subject to technical change without notice.

13 Connections standard without built-in valve Connections dimensions -tube, bottom, one behind the other Model C... Version Standard Dimensioned drawing - side view Dimensioned drawing - front view Ordering code / ) : recommended wall spacing Only possible from C.. Connection dimensions -tube, middle Model C... Version Standard Dimensioned drawing - side view Dimensioned drawing - front view Ordering code C.../ Fins at the rear ) : recommended wall spacing Connection only G / Note fixing consultation ) : recommended wall spacing Connection dimensions -tube Version Connection details Plan view For valve with dip tube, side T Distance T C... C.../ : mm : mm For valve with dip tube, bottom 0 for TKM valve, bottom Distance T C... C.../ : mm : mm T Subject to technical change without notice. Technical Documentation 0-N -

14 Connections standard without built-in valve Coupled convectors Convectors are supplied separately. Connections are to be installed on site Recommended connection size between the room heaters: G / (or one size larger than feed / return) ζ value=,0 applies for inlet and outlet with connection sizes from G / to G / and up to a water velocity of m/s ζ overall value = ζ value x number of inlets and outlets For height 0 mm connection size and coupling size G / From size C0 all coupled convectors can be connected at the bottom using a valve with dip tube or a TKM valve on the right of left Connection system Connection on same end Connection opposite ends, side Description Maximum length: L max = m Please provide a drawing with the order Maximum length: L max = m Please provide a drawing with the order /" /" First room heater Order of coupled room heaters (enter in "Special features" column) Middle room heater L max. = m /" /" L max. = m /" /" Last room heater /" Ordering code L max. = m Connection opposite ends, bottom Maximum length: L max = m Please provide a drawing with the order /" /" /" /" For connection dimensions, see "Connection dimensions" table Special connections Ordering code Description Version as per drawing 0 - Technical Documentation 0-N Subject to technical change without notice.

15 Connections version with built-in valve Version with built-in valve To ease fitting, Arbonia has developed a built-in valve system for convectors. Along with its practical advantages, this system provides a number of aesthetic features. Range available Built-in valve with adjustable k VS value (valve characteristic) integrated in header piece: - Arranged side top, left or right - As standard arranged at rear (also arranged at front as special design) - Thermostatic head ZV00000 (Z) not included, must be ordered as an accessory Connections: - -tube connection, bottom, integrated into the room heater - Connections adjacent (on valve side or middle), connection centre line mm - Flow always outside (on valve side) - Connection size: G / internal thread - Possibility of connection to a -tube system using on site H-threaded fitting ZV00000 (Z) or ZV00000 (Z) as an accessory - For convectors with a height of 0 mm on request. Maximum operating temperature: C Special versions Convectors with top grill: - Height 0 0: ordering code = AB - Height 0: on request Connection options Description Feature Ordering code Connection system Valve position side top Standard valve with thread M 0 x, Standard valve with clamp thread Valve with fine adjustment and thread M 0 x, Valve with fine adjustment and clamp thread Arrangement Connections bottom, adjacent Valve left, flow left, return left Valve right, flow right, return right Valve right, flow middle right, return middle left (max. length: 00 mm) Valve left, flow middle left, return middle right (max. length: 00 mm) Tapping size G / internal thread feed G / internal thread return VL RL Dimension drawings Model Dimension drawing Side view C../V, C...V C.../V 0 Connections: x G/" internal 0 Valve left Valve right Attention: flow always outside Subject to technical change without notice. Technical Documentation 0-N -

16 Air vent, Drain Air vent Description Feature Ordering code Version Air vent tapping standard version Built-in air vent with rotating outlet No air vent, only if imperative Arrangement Position recommended by the factory standard version ) Position on request ) Tapping size G / G / G / ) For position see illustration of the arrangement of the connections in the "Connection options flow / return" table ) If the tapping cannot be arranged in the required position for technical reasons, the tapping will instead be arranged in the position recommended by the factory Drain Description Feature Ordering code Version No drain, only if imperative standard version ) Drain tapping Blanking plugs fitted Arrangement Position recommended by the factory standard version ) Position on request ) Tapping size G / G / ) If a drain tapping is necessary for technical reasons, this will be fitted as standard in the factory ) For position see illustration of the arrangement of the connections in the "Connection options flow / return" table ) If the tapping cannot be arranged in the required position for technical reasons, the tapping will instead be arranged in the position recommended by the factory 0 - Technical Documentation 0-N Subject to technical change without notice.

17 Fixing Fixing Fixing dimensions 0 H C.../ L C.../ C.../ C.../ C.../ C... C... C... C... 0 Fixing with rear lugs Name Dimension drawing Ordering code Without rear lugs standard version With rear lugs C/, C /, C/ B C, C, C, C, C, C T C/, C/, C/ 0 0 L 0 0 T Subject to technical change without notice. Technical Documentation 0-N -

18 Fixing Number of fixing points Number fixing points Dimension drawing L = 0, -,00 m fixing points L =,0 -,00 m fixing points / / L =,0 -,00 m / / / Attention: all models not listed above cannot be fitted with rear lugs. 0 - Technical Documentation 0-N Subject to technical change without notice.

19 Fixing Fixing with brackets Fixing type Version Model On wall with wall brackets (examples): Length L [mm] Number of brackets 0 00 Suitable brackets ZB000 (W) ZB000 (W) ZB000 (W) Wall brackets: ZB000 (W) Wall brackets: ZB00 (W) Wall brackets: ZB000 (W) ZB000 (W with rearlugs ) C C/ C C C C ZB00 (W) ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) Wall brackets: ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) Wall brackets: ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) ZB000 (W0) On wall with wall brackets and floor brackets: C0 C C0 C C0 C without rear lugs C0 C Wall brackets ZB00 (W0) Wall brackets ZB00 (W0) On floor with wall brackets and floor brackets: without rear lugs C0 C C0 C C0 C C0 C Floor brackets ZB00 (W0) Floor brackets ZB00 (W0) ) Rear lugs are only welded to convectors on request (ordering code : B) Attention: characteristics of the wall must be checked. Maximum loading capacity not referred to bracket/wall joint. Subject to technical change without notice. Technical Documentation 0-N -

20 Fixing Selection of further brackets Model C../ C.. C../ C.. C../ C.. C../ C.. Depth [mm] ZB000 (B0) ZB000 (B0) ZB000 (B0) ZB000 (B0) ZB000 (B0) ZB000 (B0) ZB000 (B0) ZB000 (B0) Floor fixing ZB000 (B) ZB000 (B) ZB000 (B) ZB000 (B) ZB000 (B) ZB000 (B) ZB000 (B) ZB000 (B) Wall fixing ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) ZB00 (B0) ZB00 (W) Name Description Floor brackets ZB000 (B0 B) Stepless adjustable in height: - ZB000 (B0 B0): H = mm - ZB000 (B B): H = 0 mm Surface: - Galvanised - Finished AF, CF, SF Universal bracket ZB00 (B0 B0) Stepless adjustable in height and depth Height adjustment range: H = 0 mm Can be cut on site Surface: - Galvanised - Finished AF, CF, SF 0 Wall bracket ZB00 (W W) Stepless adjustable in depth Maximum loading capacity: - ZB00 (W): 0 kg - ZB00 (W): 0 kg - ZB00 (W): 0 kg - ZB00 (W): 0 kg Surface: - Galvanised - Finished IAFI, ICFI, ISFI Please check the characteristics of the wall and choose the fixing variant and the plugs and screws to suit. - Technical Documentation 0-N Subject to technical change without notice.

21 Fixing Fixing with screwed feet Description Dimension drawing For models C...- C...- with a depth of mm without rear fins L Only available for convectors with connection type -tube, bottom, opposite ends (ordering code : or ) Height foot: mm -part feet cover the fixings and the fittings Screw-on brackets open to the outside are mounted on site and closed using cover plates supplied A screw-on bracket with break-out Dimensions in mm mm to the inside for thermostatic Cover: head (thermostatic head available as accessory, mounted on site) Screw-on brackets, cover plates and screws included H T Length L [mm] Number of feet Ordering code FUS Cover plate Screw-on bracket Fixing with soil stand bracket Description Dimension drawing Bench holder set For models C...- and C...- Can be added later, also for universal convectors Shelf not in product range For use in conjunction with bracket ZB00 (W0) Do not use shelf as bench! (see fixing as bench) L BH max. 0 Length L [mm] Number of feet Suitable brackets ZM000 (B) Bench holder set For models C...- and C...- Can be added later, also for universal convectors Seat not in product range For use in conjunction with bracket ZB00 (W0) L BH max ZM000 (B) 0 Subject to technical change without notice. Technical Documentation 0-N -

22 Fixing 0 Fixing as bench Description Dimensioned drawing Drawing For convectors C with a depth of mm T ZB00 Convector can be used as H seat, window sill or shelf Brackets and fixing must be ZB00000 ordered separately as accessories Bench or shelf not in product range and must be provided ZB00 on site H A Brackets are finished (AF, CF or SF) B ZB00000 Dimensions in mm A: mounting on finished floor, B: mounting on unfinished floor with adjusting screw Brackets with different dimensions are available on request as special version. Selection of the brackets and fixings C0 C0/ C0 C0/ C0 C0/ C C/ C C/ C C/ C C/ C C/ C C/ C C/ C C/ C C/ Depth [mm] Height [mm] Brackets under room heater For finished floor For unfinished floor Brackets above Brackets Adjusting screws room heater Ordering Ordering Ordering Ordering Length[mm] Number code Number code Number code Number code Number 0 00 ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00(B ZB00000 ZB (B) ) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00(B ZB00000 ZB (B) ) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) Suitable brackets ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) Fixing room heater Ordering code ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) - Technical Documentation 0-N Subject to technical change without notice.

23 Fixing Mounting in floor channel Wall spacing and floor spacing must match depth as a minimum Open cross-section of the grill cover must be at least 0 % Reduction of the heat output by to % (as a function of the grill cover) Panel must reach the cover grill Bottom edge of the panel must be flush with the bottom edge of the convector Types of mounting Installation situation Heat output = cold air dropping from the window above Dimension drawing W T 0-0- BA Heat output > cold air dropping from the window above Dimensions in mm BA: floor spacing W: Wall spacing W T W 0-0- BA Dimensions in mm W: outside wall spacing W: inside wall spacing BA: floor spacing 0 Subject to technical change without notice. Technical Documentation 0-N -

24 Pressure versions, Fittings, Surface finishes, Special versions Pressure versions, fittings and attachments Ordering code Description Standard version bar (00 kpa) High-pressure version 0 bar (000 kpa) 0 Version Description Dimension drawing With top grill Reduction in heat output: % Top grills for screwless mounting. For, convectors with fins on rear, special fixings are included Bracket ZB00 (W0) cannot be used with welded top grill and galvanised convector Dimensions in mm Ordering code AB Surface finishes 0 Description Finish Ordering code Colour Ordering code /0 AllFinish in white Pure white RAL 00 standard version AF RAL 00 Traffic white RAL 0 AF RAL 0 Primed in cream-white ET Primed in cream-white and packed in plastic sheet EF ColorFinish, finished in standard colour ) RAL colour SuperFinish in colour of choice ) ) SF ) For information on ordering, see ordering process section : General information and colour chart ) Not in all colours CF CF SF Sanitary colour ) Manufacturer's colour Arbonia special colour ) Colour number Ordering code Colour number from colour card Colour number manufacturer's colour SuperFinish in gloss silver SF GLS Clear lacquer TF Textured paint after priming Pure white RAL 00 standard version Traffic white RAL 0 SL SL RAL RAL 00 0 In colour of choice (manufacturer's colour) ) ) ) ) In colour of choice (Arbonia special colour) KL KL Manufacturer's colour Colour number manufacturer's colour Arbonia special colour ) Hot-dip galvanised, outside, for wet rooms Without paint finish With textured paint in pure white RAL 00 standard version With textured paint in traffic white RAL 0 ) ) With structured paint in colour of choice (manufacturer's colour) With textured paint in colour of choice (sanitary colour) ) ) With textured paint in colour of choice (Arbonia special colour) ) ) Anti-microbial coating Pure white RAL 00 standard version Traffic white RAL 0 ZN ZL ZL ZK ZK ZK AM AM RAL RAL Manufacturer's colour Sanitary colour ) Arbonia special colour ) RAL RAL 00 0 Colour number manufacturer's colour Technical Documentation 0-N Subject to technical change without notice.

25 T W Convectors Pressure versions, Fittings, Surface finishes, Special versions Special versions Ordering code Description Version as per drawing Angled version Angle α can be between 0 and 0 Number of angles limited Only available for versions with top grill (ordering code : AB) Not available in all dimensions in hot-dip galvanised version. On request Convector must be suitable for transport Please provide a drawing with dimensions or template with the order Description / dimension drawings Ordering code L L W T L L, L: Length of the limb, measured on the wall α: Angle W: Wall spacing L 0 Subject to technical change without notice. Technical Documentation 0-N -

26 Pressure versions, Fittings, Surface finishes, Special versions Curved version Minimum bending radius R min : 00 mm Only for convectors in high-pressure version (ordering code : 0) Not in all dimensions in hot-dip galvanised version. On request Convector must be suitable for transport Please provide a drawing with dimensions or template with the order Special top grill on request Description / dimension drawings L W Ordering code R Inside radius W T L R Outside radius T 0 W: Wall spacing R: Bending radius (inside radius / outside radius) 0 - Technical Documentation 0-N Subject to technical change without notice.

27 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth Model C0/ C0 C0/ C0 Height H [mm] Depth T [mm] Weight per metre M [kg/m],0,,,0 Surface per metre A [m²/m] 0,,,,0 Volume per metre V [dm³/m] 0,,,, Standard water flow rate per metre q ms [kg/h m],,,0, Radiated portion s [%] 0 Radiator classification n [Exp],,,, Φ L ΔT K [Watt/m] 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Subject to technical change without notice. Technical Documentation 0-N -

28 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth 0 Model C0/ C0 C0/ C0 Height H [mm] Depth T [mm] Weight per metre M [kg/m],,0,, Surface per metre A [m²/m],,,, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m],,,, Radiated portion s [%] Radiator classification n [Exp],,,, Φ L ΔT K [Watt/m] 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Technical Documentation 0-N Subject to technical change without notice.

29 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m],,,, Surface per metre A [m²/m],,,, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m],,,0, Radiated portion s [%] 0 Radiator classification n [Exp],,0,, Φ L ΔT K [Watt/m] Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Subject to technical change without notice. Technical Documentation 0-N -

30 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth 0 Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m],,,, Surface per metre A [m²/m],,,, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m], 0,,, Radiated portion s [%] Radiator classification n [Exp],,,, Φ L ΔT K [Watt/m] 0 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Technical Documentation 0-N Subject to technical change without notice.

31 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m],,,, Surface per metre A [m²/m],0,,, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m],,,, Radiated portion s [%] 0 Radiator classification n [Exp],,,, Φ L ΔT K [Watt/m] Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Subject to technical change without notice. Technical Documentation 0-N -

32 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth 0 Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m] 0,,,0, Surface per metre A [m²/m],,,, Volume per metre V [dm³/m],,, 0, Standard water flow rate per metre q ms [kg/h m],, 0,0,0 Radiated portion s [%] Radiator classification n [Exp],,,, Φ L ΔT K [Watt/m] 0 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Technical Documentation 0-N Subject to technical change without notice.

33 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m],, 0,,0 Surface per metre A [m²/m],0,,0, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m],, 0,,0 Radiated portion s [%] 0 Radiator classification n [Exp],0,,, Φ L ΔT K [Watt/m] 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Subject to technical change without notice. Technical Documentation 0-N -

34 Heat output per room heater Height 0 mm with heat outputs as a function of length and depth 0 Model C/ C C/ C Height H [mm] Depth T [mm] Weight per metre M [kg/m],,0,, Surface per metre A [m²/m],0,,0, Volume per metre V [dm³/m],,,, Standard water flow rate per metre q ms [kg/h m],,,, Radiated portion s [%] Radiator classification n [Exp],,0,, Φ L ΔT K [Watt/m] 0 Length L [mm] Φ S ΔT K // C Φ S ΔT K: standard heat output at // C (ΔT K) (EN ) ΔT K: standard temperature rise Weight per radiator > kg (dry) Φ S ΔT K // C Φ S ΔT K // C Φ S ΔT K // C Max. length L [mm] Technical Documentation 0-N Subject to technical change without notice.

35 Technical data per metre Height H [mm] Depth T [mm] Model ΦΔT 0K 0/0/ C [Watt/m] Heat output EN Φ L ΔT K // C [Watt/m] ΦΔT K 0// C [Watt/m] ΦΔT 0K // C [Watt/m] Individual calculation of heat outputs see section : General information Radiator classification n [Exp] Weight per metre M [kg/m] Surface per metre A [m²/m] Volume per metre V [dm³/m] Standard water flow rate per metre q ms [kg/h m] Radiated portion s [%] C0/,,0 0, 0,, C0,,,,, C0/ 0,,,,,0 C0,,0,0,, 0 C0/,,,,, 0 C0 00,,0,,, 0 C0/ 0,,,,, 0 C0 0,,,,, 0 C/,,,,, C,0,,,, C/ 0,,,,,0 C 0,,,,, 0 C/ 0,,,,, 0 C 0,,,, 0, 0 C/ 0,,,,, 0 C,,,,, 0 C/,,,0,, C,,,,, C/,,,,, C,,,,, 0 C/, 0,,,, 0 C 0 0,,,,, 0 C/ ,,0,, 0,0 0 C 0,,, 0,,0 0 C/,0,,0,, C 0 0 0,,,,, C/, 0,,0, 0, C 0,,0,,,0 0 C/ 0,,,0,, 0 C,0,0,,, 0 C/ 0,,,0,, 0 C 0,,,,, 0 0 Subject to technical change without notice. Technical Documentation 0-N -

36 Convector WVO Description Model Standard without built-in valve C....../W Explanation C : convector model code... : height in cm... : number of tubes carrying water / : with fins at rear W : with shield for radiated heat Example C/W C : convector : height cm : tubes carrying water / : with fins at rear W : with shield for radiated heat Model C....../WV Version with built-in V: with built-in valve valve 0 General Form and function combine in modern architecture in a harmonious manner. Arbonia convectors support the architect and client in this harmony: the clear emphasis of the horizontal line, clean side connections and the fine structure of the cover permit open installation. High heat output from small dimensions and the diverse range round off the attractive image of this room heater. Convectors WVO are GUV-compliant in the special version with top grill. On convectors in WVO-version, the continuous, insulated shield reduces the heat radiated in this direction. Arbonia recommends the use of convectors WVO for window areas. Rear view: Layout of the shield for radiated heat: Aluminiumlining Range available depths:,, and mm - All models with fins at rear and shield for radiated heat on the rear heights: 0, 0, 0 and 0 mm Length: mm: steps: 00 mm mm: steps: 0 mm (manufacturing tolerance: ± mm, measured at C) - Maximum length mm Shield for radiated heat: - Continuous, sheet metal shielding for the rear fins, cannot be removed - With polystyrene insulation and aluminium lining as reflective shield - k value < 0, Watt/m K -tube connections Polystyrene 0 mm Steel sheet mm - Technical Documentation 0-N Subject to technical change without notice.

37 Convector WVO Description Special versions -tube connections Version with built-in valve Built-in air vent with rotating outlet High-pressure version 0 bar (000 kpa) Top grill (GUV-compliant) Screwed feet Angled or curved version Fixing as bench: - For convectors with depth mm - Order brackets as accessories Surface finishes AllFinish in traffic white (AF) RAL 0 AllFinish in pure white (AF) RAL 00 Primed in cream-white (ET) Primed in cream-white and packed in plastic sheet (EF) ColorFinish in standard colour (CF) SuperFinish, finished in colour of choice (SF) ) Anti-microbial coating (AM) Warning on painting of convectors WVO on site The polystyrene insulation for the shield for radiated heat must not come into contact with solvents or paint thinners. The paint finish is not allowed to be baked. Forced drying at C is allowed. All finishes are baked at 0 C. For detailed information see "Colour Fashion of the Arbonia Radiators". Operating conditions For closed water heating systems in accordance with DIN 0 and water quality in accordance with VDI Can be used in conventional and low temperature areas Can be used for district heating and high-rise buildings (high permissible operating pressure) Not suitable for steam-based heating systems Length expansion: 0, mm/m at a temperature difference of K Properties of relevance to operation Standardversion High-pressure version Operating pressure [bar (kpa)],0 (00) 0,0 (000) Test pressure [bar (kpa)], (0),0 (00) Max. temperature [ C] Minimum water flow rate The minimum water flow rate must not be less than 0 % of the standard water flow rate in accordance with EN to avoid a reduction in the heat output. This applies both to connection on same end and on opposite ends. Pressure drop Δp Δp = ζ x ρ/ x w Δp: Pressure drop [Pa] ζ: Resistance coefficient Zeta [] ρ: Density of the water [kg/m ] w: Water velocity [m/s] The ζ values are given in the connection table and apply for a water velocity of up to m/s. Heat outputs The heat outputs given are determined and registered in accordance with the guidelines in EN : DIN CERTCO registered. RAL tested and registered. Tender text Room heaters with up to five 0 x x, mm steel tubes arranged one behind the other and up to four 0 x x, mm steel tubes arranged one above the other with convector fins and collectors on the ends connected by hidden welds and rounded edges all round with R min = mm. Ready to install with to connection threads on the ends in the collectors for flow and return as well as air vent and drain. Shield for radiated heat with polystyrene insulation and aluminium laminate, cannot be removed, with a k-value < 0, Watt/m K. Version with permanently fitted top grill (at extra charge) complies with the basic principles for the testing of the health and safety of room heaters (statutory accident insurance). Priming in accordance with DIN 00 part and powder coating in accordance with DIN 00 part. Pressure and leak tested. Heat output tested and measured in accordance with EN. CE marked. Suitable for closed water heating systems in accordance with DIN 0 and water quality in accordance with VDI. Maximum permissible operating temperature C Max. operating pressure: bar / 00 kpa 0 bar / 000 kpa Suitably packed for transport. 0 ) Not in all colours Subject to technical change without notice. Technical Documentation 0-N -

38 Convector WVO Connections standard without built-in valve Connection options flow / return Connection system Ord. code ζ value Arrangement Ordering code Connec. size Ordering code Flow Return Dimension drawings -tube, side,0,0 G / G / G / See page Connection dimensions -tube, side -tube, side and bottom,0,0 G / G / G / See page Connection dimensions -tube, side and "Connections dimensions -tube, bottom" -tube, bottom,0,0 -tube, bottom, one behind the other,0,0 G / G / G / G / G / G / See page Connection dimensions -tube, bottom See page Connection dimensions -tube, bottom, one behind the other Only possible from C../W -tube, bottom, middle-middle,,0,0 G / vertical underside ) -tube, for valve with dip tube, side,with dip tube Ø mm -tube, for valve with dip tube, bottom,with dip tube Ø mm 0,0,0 G / 0,0,0 G / See page Connection dimensions -tube, middle See page Connection dimensions -tube See page Connection dimensions -tube -tube, for TKM valve, bottom, with dip tube,0,0 G / See page Connection dimensions -tube 0 ) Maximum length: 00 mm L: recommended position for air vent tapping: Standard baffle; baffle with Ø mm hole; valve with dip tube; TKM valve On models C0/W the connections in arrangement and are only possible in G /. - Technical Documentation 0-N Subject to technical change without notice.

39 Convector WVO Connections standard without built-in valve Connection dimensions -tube, side C0/W ) C....../W C....../W Connection details Height 0 mm ) Height 0 mm ) C/W 0 0 C0/W C/W 0 0 C0/W C/W /" - /" 0 0 C0/W C/W Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions ) Only G / (for arrangement feature : or ) Subject to technical change without notice. Technical Documentation 0-N -

40 Convector WVO Connections standard without built-in valve Connection dimensions -tube, side C/W C....../W C....../W Connection details Height 0 mm ) Height 0 mm ) C/W 0 0 C/W C/W 0 0 C/W C/W 0 0 /" - /" C/W C/W Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions -0 Technical Documentation 0-N Subject to technical change without notice.

41 Convector WVO Connections standard without built-in valve Connections dimensions -tube, bottom C0/W C....../W C....../W Connection details Height 0 mm ) Height 0 mm ) C/W 0 0 C0/W C/W /" - /" C0/W C/W /" C0/W C/W 0 0 Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions 0 Subject to technical change without notice. Technical Documentation 0-N -

42 Convector WVO Connections standard without built-in valve Connections dimensions -tube, bottom C/W C....../W C....../W Connection details Height 0 mm ) Height 0 mm ) C/W 0 0 C/W C/W /" - /" C/W C/W /" C/W C/W Dimensions in mm ) Wall and floor spacings are recommended minimum dimensions - Technical Documentation 0-N Subject to technical change without notice.

43 Convector WVO Connections standard without built-in valve Connections dimensions -tube, bottom, one behind the other Model Version Dimensioned drawing - side view Dimensioned drawing - front view C.../W Version with shield for radiated heat min. 00 Ordering code / Only possible from C../W Connection dimensions -tube, middle Model Version Dimensioned drawing - side view Dimensioned drawing - front view C.../W Version with shield min. 00 for radiated heat Ordering code Connection only G / Note fixing consultation Connection dimensions -tube Version Connection details Plan view For valve with dip tube, side T Distance T C.../W : mm For valve with dip tube, bottom T Distance T for TKM valve, bottom C.../W : mm 0 Subject to technical change without notice. Technical Documentation 0-N -

44 Convector WVO Connections standard without built-in valve Coupled convectors Convectors are supplied separately. Connections are to be installed on site Recommended connection size between the room heaters: G / (or one size larger than feed / return) ζ value=,0 applies for inlet and outlet with connection sizes from G / to G / and up to a water velocity of m/s ζ overall value = ζ value x number of inlets and outlets For height 0 mm connection size and coupling size G / From size C0 all coupled convectors can be connected at the bottom using a valve with dip tube or a TKM valve on the right of left Connection system Connection on same end Connection opposite ends, side Connection opposite ends, bottom Description Maximum length: L max = m Please provide a drawing with the order Maximum length: L max = m Please provide a drawing with the order Maximum length: L max = m Please provide a drawing with the order /" /" /" For connection dimensions, see "Connection dimensions" table Order of coupled room heaters(enter in "Special features" column) First room heater Middle room heater L max. = m /" /" L max. = m /" /" L max. = m /" /" Last room heater /" /" Ordering code Special connections Ordering code Description Version as per drawing 0 - Technical Documentation 0-N Subject to technical change without notice.

45 Convector WVO Connections version with built-in valve Version with built-in valve To ease fitting, Arbonia has developed a built-in valve system for convectors. Along with its practical advantages, this system provides a number of aesthetic features. Range available Built-in valve with adjustable k VS value (valve characteristic) integrated in header piece: - Arranged side top, left or right - As standard arranged at rear (also arranged at front as special design) - Thermostatic head ZV00000 (Z) not included, must be ordered as an accessory Connections: - -tube connection, bottom, integrated into the room heater - Connections adjacent (on valve side or middle), connection centre line mm - Flow always outside (on valve side) - Connection size: G / internal thread - Possibility of connection to a -tube system using on site H- threaded fitting ZV00000 (Z) or ZV00000 (Z) as an accessory - For convectors with a height of 0 mm on request. Maximum operating temperature: C Special versions Convectors with top grill: - Height 0 0: ordering code = AB - Height 0: on request Connection options Model Dimension drawing Side view C.../WV 0 Connections: x G/" internal Valve left Valve right Attention: flow always outside Dimension drawings Description Feature Ordering code Connection system Valve position side top Standard valve with thread M 0 x, Standard valve with clamp thread Valve with fine adjustment and thread M 0 x, Valve with fine adjustment and clamp thread Arrangement Connections bottom, adjacent Valve left, flow left, return left Valve right, flow right, return right Valve right, flow middle right, return middle left (max. length: 00 mm) Valve left, flow middle left, return middle right (max. length: 00 mm) Tapping size G / internal thread feed G / internal thread return VL RL 0 Subject to technical change without notice. Technical Documentation 0-N -

46 Convector WVO Air vent, Drain Air vent Description Feature Ordering code Version Air vent tapping standard version Built-in air vent with rotating outlet No air vent, only if imperative Arrangement Position recommended by the factory standard version ) Position on request ) Tapping size G / G / G / ) For position see illustration of the arrangement of the connections in the "Connection options flow / return" table ) If the tapping cannot be arranged in the required position for technical reasons, the tapping will instead be arranged in the position recommended by the factory Drain Description Feature Ordering code Version No drain, only if imperative standard version ) Drain tapping Blanking plugs fitted Arrangement Position recommended by the factory standard version ) Position on request ) Tapping size G / G / ) If a drain tapping is necessary for technical reasons, this will be fitted as standard in the factory ) For position see illustration of the arrangement of the connections in the "Connection options flow / return" table ) If the tapping cannot be arranged in the required position for technical reasons, the tapping will instead be arranged in the position recommended by the factory 0 - Technical Documentation 0-N Subject to technical change without notice.

47 Convector WVO Fixing Fixing Safety distance convector WVO Minimum distance for single pane safety glass (ESG): recommendation 00 mm 00 min Shield for radiated Fixing with brackets Fixing type Version Model Length L [mm] Number of brackets Suitable brackets On wall with wall brackets and floor brackets: C0/W C/W C0/W C/W C0/W C/W without rear lugs C0/W C/W Wall brackets ZB00 (W0) Wall brackets ZB00 (W0) On floor with wall brackets and floor brackets: without rear lugs C0/W C/W C0/W C/W C0/W C/W ZB00 (W0) C0/W C/W Floor brackets ZB00 (W0) Floor brackets ZB00 (W0) Attention: characteristics of the wall must be checked. Maximum loading capacity not referred to bracket/wall joint. Subject to technical change without notice. Technical Documentation 0-N -

48 Convector WVO Fixing Selection of further brackets Model C../W C../W C../W C../W Depth [mm] Floor fixing ZB000 (B0) ZB000 (B) ZB00 (B0) ZB000 (B0) ZB000 (B) ZB00 (B0) ZB000 (B0) ZB000 (B) ZB00 (B0) ZB000 (B0) ZB000 (B) ZB00 (B0) Wall fixing ZB00 (W) ZB00 (W) ZB00 (W) ZB00 (W) Name Description Floor brackets ZB000 (B0 B) Stepless adjustable in height: - ZB000 (B0 B0): H = mm - ZB000 (B B): H = 0 mm Surface: - Galvanised - Finished AF, CF, SF Universal bracket ZB00 (B0 B0) Stepless adjustable in height and depth Height adjustment range: H = 0 mm Can be cut on site Surface: - Galvanised - Finished AF, CF, SF 0 Wall bracket ZB00 (W W) Stepless adjustable in depth Maximum loading capacity: - ZB00 (W): 0 kg - ZB00 (W): 0 kg - ZB00 (W): 0 kg - ZB00 (W): 0 kg Surface: - Galvanised - Finished IAFI, ICFI, ISFI Please check the characteristics of the wall and choose the fixing variant and the plugs and screws to suit. - Technical Documentation 0-N Subject to technical change without notice.

49 Convector WVO Fixing Fixing with screwed feet Description Dimension drawing For convectors WVO with a depth of mm L Only available for convectors with connection type -tube, bottom, opposite ends (ordering code : or ) Height foot: mm -part feet cover the fixings and the fittings Screw-on brackets open to the outside are mounted on site and closed using cover plates supplied A screw-on bracket with break-out mm to the inside for thermostatic head (thermostatic head available as accessory, mounted on site) Dimensions in mm Screw-on brackets, cover plates and Cover: screws included T WVO overhang Length L [mm] Number of feet Ordering code FUS Cover plate Screw-on bracket Fixing with soil stand bracket Description Bench holder set For models C...-/W and C...-/W Can be added later, also for universal convectors Shelf not in product range Height foot: mm For use in conjunction with bracket ZB00 (W0) Not suitable for use as seat Dimension drawing L BH max. 0 Length L [mm] Number of feet Suitablebrackets ZM000 (B) Bench holder set For models C...-/W and C...-/W Can be added later, also for universal convectors Seat not in product range Height foot: mm For use in conjunction with bracket ZB00 (W0) L BH max ZM000 (B) 0 Subject to technical change without notice. Technical Documentation 0-N -

50 Convector WVO Fixing 0 Fixing as bench Description Dimension drawing Drawing For convectors WVO with a depth of mm T ZB00 Convector can be used as H seat, window sill or shelf Brackets and fixing must be ZB00000 ordered separately as accessories Bench or shelf not in product range and must be provided ZB00 on site H A Brackets are finished (AF, CF or SF) B ZB00000 Dimensions in mm A: mounting on finished floor, B: mounting on unfinished floor with adjusting screw Brackets with different dimensions are available on request as special version. Selection of the brackets and fixings Convector WVO C0/W C0/W C0/W C0/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W Depth [mm] Height [mm] Brackets under room heater For finished floor For unfinished floor Brackets above Brackets Adjusting screws room heater Ordering Ordering Ordering Ordering Length[mm] Number code Number code Number code Number code Number 0 00 ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00000 ZB B (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00000 ZB B (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) ZB00 ZB00 ZB00000 ZB (B) (B) (B0) (B) Suitable brackets ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) Fixing room heater Ordering code ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) ZB00 (B) - Technical Documentation 0-N Subject to technical change without notice.

51 Convector WVO Pressure versions, Fittings, Surface finishes, Special versions Pressure versions, fittings and attachments Ordering code Description Standard version bar (00 kpa) High-pressure version 0 bar (000 kpa) 0 Version Description Dimension drawing With top grill Reduction in heat output: % Top grills for screwless mounting. For, convectors with fins on rear, special fixings are included Bracket ZB00 (W0) cannot be used with welded top grill and galvanised convector Dimensions in mm Ordering code AB Surface finishes Description Finish Ordering code Colour Ordering code /0 AllFinish in white Pure white RAL 00 standard version AF RAL 00 Traffic white RAL 0 AF RAL 0 Primed in cream-white ET Primed in cream-white and packed in plastic sheet EF ColorFinish, finished in standard colour ) RAL colour SuperFinish in colour of choice ) ) SF ) For information on ordering, see ordering process section : General information and colour chart ) Not in all colours Warning on painting of convectors WVO on site The polystyrene insulation for the shield for radiated heat must not come into contact with solvents or paint thinners. The paint finish is not allowed to be baked. Forced drying at C is allowed. Special versions CF CF SF Sanitary colour ) Manufacturer's colour Arbonia special colour ) Colour number Ordering code Colour numberfrom colour card Colour numbermanufacturer's colour SuperFinish in gloss silver SF GLS Anti-microbial coating Pure white RAL 00 standard version Traffic white RAL 0 Ordering code Description Version as per drawing AM AM RAL RAL Subject to technical change without notice. Technical Documentation 0-N -

52 T W Convectors Convector WVO Pressure versions, Fittings, Surface finishes, Special versions Angled version Angle α can be between 0 and 0 Number of angles unlimited Only available for versions with top grill (ordering code : AB) Not available in all dimensions in hot-dip galvanised version. Please request information Convector must be suitable for transport Please provide a drawing with dimensions or template with the order Description / dimension drawings Ordering code L W T L L L, L: Length of the limb, measured on the wall α: Angle W: Wall spacing L 0 - Technical Documentation 0-N Subject to technical change without notice.

Section 8 Column radiators

Section 8 Column radiators Section s Description Connections Standard without built-in valve -or- Version with built-in valve Air vent, Drain Fixing and mounting Pressure versions, Fittings, Surface finishes, Special versions eat

More information

Hudevad P100. Technical datasheet

Hudevad P100. Technical datasheet Technical datasheet Key benefits Available in three depths Highly flexible in use Integrated top grille Harmonious and finished look Kundenedfal Low, streamlined design Ideal in front of glazing to prevent

More information

zehnder stratos CS CS CS CSW CSW Product Overview Model Code (example)

zehnder stratos CS CS CS CSW CSW Product Overview Model Code (example) Product Overview Model Code (example) CS-15-19 Depth (cm) eight (cm) CS = Convector Stratos CS = Convector Stratos with rear dummy panel CS-..-10 CS-..-13 No. of panels: 2 No. of fins: 2 Depth: 98mm eight:

More information

Ascotherm eco KC281 Heating and cooling in 2-conductor system

Ascotherm eco KC281 Heating and cooling in 2-conductor system KC281 Heating and cooling in 2-conductor system Tender specification, range available and sizes Tender specification Version KC281 heating and cooling in 2-pipe system Ready-to-install floor pans for the

More information

Swirl Diffuser. Type SDW T 2.2/1/B/1. recommended for room heights from approx m

Swirl Diffuser. Type SDW T 2.2/1/B/1. recommended for room heights from approx m T 2.2/1/B/1 Swirl Diffuser Type SDW recommended for room heights from approx. 2.60... 4.00 m TROX UK Ltd Caxton Way Thetford Norfolk IP24 3SQ Telephone +44(0) 1842 54545 Telefax +44(0) 1842 63051 e-mail

More information

Krantz Components. Twist outlet DD-N... for ceiling installation. Air distribution systems

Krantz Components. Twist outlet DD-N... for ceiling installation. Air distribution systems Krantz Components Twist outlet DD-N... for ceiling installation Air distribution systems DS E 0. Twist outlet Preliminary remarks and construction design Preliminary remarks Twist outlets for ceiling installation

More information

Dimensions. Order code. Materials and finish. lindab ceiling diffusers

Dimensions. Order code. Materials and finish. lindab ceiling diffusers LKP Description LCP is a flush-mounted square diffuser with a circular unperforated face plate for installation in ceiling systems. LCP can be used for both supply and exhaust air. LCP is suitable for

More information

MR medium rating busbar

MR medium rating busbar technical information General features MR is fully compliant with S EN 0-, specifically, the rated current of the Zucchini busbar trunking systems is always rated at the average ambient temperature of

More information

Air distribution systems. Adjustable induction outlet IN-V...

Air distribution systems. Adjustable induction outlet IN-V... ir distribution systems djustable induction outlet IN-V... DS E 0. Construction and function Preliminary remarks In addition to its induction outlet with preset discharge direction ), KRNTZ KOMPONENTEN

More information

IBV Series C Carbon Steel Inverted Bucket Vertical Steam Trap

IBV Series C Carbon Steel Inverted Bucket Vertical Steam Trap Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

IBV Series Z Alloy Steel Inverted Bucket Vertical Steam Trap

IBV Series Z Alloy Steel Inverted Bucket Vertical Steam Trap Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

Ceiling Diffuser. Type ADLR with circular face. Type ADLR-Q with square face 2/16/EN/8

Ceiling Diffuser. Type ADLR with circular face. Type ADLR-Q with square face 2/16/EN/8 2/16/EN/8 Ceiling Diffuser Type ADLR with circular face Type ADLR-Q with square face TROX GmbH Telephone +49/28 45/2 02-0 Telefax +49/28 45/2 02-2 65 Heinrich-Trox-Platz e-mail trox@trox.de D-47504 Neukirchen-Vluyn

More information

Krantz. RL-C2 radial slot outlet. Air distribution systems

Krantz. RL-C2 radial slot outlet. Air distribution systems RL-C2 radial slot outlet Air distribution systems DS E 04.1 Introduction The RL-C2 radial slot outlet with circular face generates a turbulent mixed flow. It is used for supply and return air distribution

More information

HELLA. Linear slot diffuser. Ordering codes. HELLA - Linear diffuser. Linear Diffusers 1 / 18. Example of the ordering code HELLA B-0-0-AN

HELLA. Linear slot diffuser. Ordering codes. HELLA - Linear diffuser. Linear Diffusers 1 / 18. Example of the ordering code HELLA B-0-0-AN Linear Diffusers / 8 HELLA Linear slot diffuser Ordering codes HELLA - Linear diffuser HELLA - Number of slots... Diffuser length L (mm) ) Increment mm... Deflector colour Damper Diffuser construction

More information

Slot diffusers. Slot diffusers, Round duct diffusers. Slot diffusers. Slot diffusers LD-13, LD-14

Slot diffusers. Slot diffusers, Round duct diffusers. Slot diffusers. Slot diffusers LD-13, LD-14 , Round duct diffusers D-, D- Application D- and D- slot diffusers are designed for the supply of air in rooms with floor to ceiling heights of.5 to m for supplying either cold or warm air, in particular

More information

PELICAN Ceiling. Square ceiling air diffuser for supply air and extract air QUICK FACTS

PELICAN Ceiling. Square ceiling air diffuser for supply air and extract air QUICK FACTS Square ceiling air diffuser for supply air and extract air QUICK FACTS Flexible distribution pattern, yet the acoustic data remains the same One K-factor regardless of distribution pattern Designed for

More information

Nozzle diffuser. Dimensions

Nozzle diffuser. Dimensions Dimensions ØU Ød H 0 ØA Description is a circular diffuser with individually adjustable nozzles. The diffuser is suitable for the horizontal supply of cooled air, where great flexibility in the dispersal

More information

MYSON COLUMN RADIATORS. MYSON TECHNICAL GUIDE heatingthroughinnovation.

MYSON COLUMN RADIATORS. MYSON TECHNICAL GUIDE heatingthroughinnovation. MYSON MYSON Eastern Avenue, Team Valley, Gateshead, Tyne & Wear NE 0PG, UK T: 0 0, F: 01 1, sales@myson.co.uk, www.myson.co.uk MYSON RADATORS. TECHNCAL GUDE 1 heatingthroughinnovation. heatingthroughinnovation.

More information

Plain diffuser. Dimensions

Plain diffuser. Dimensions Dimensions Ø U Ød B C Ø E Ø A Description is a circular diffuser with an unperforated adjustable face plate and can be used for both supply and extract air. The diffuser can be switched between horizontal

More information

SWIFT Ceiling. Square ceiling air diffuser for supply air QUICK FACTS

SWIFT Ceiling. Square ceiling air diffuser for supply air QUICK FACTS Square ceiling air diffuser for supply air QUICK FACTS Flush design Also available in a version for extract air. Designed for modular suspended ceilings (600 x 600 mm) Quick Access Adapter for systemized

More information

Krantz. Radial slot outlet with square blade array RL-Q2... circular blade array RL-R2... Air distribution systems DS 4186 E 09.

Krantz. Radial slot outlet with square blade array RL-Q2... circular blade array RL-R2... Air distribution systems DS 4186 E 09. Krantz Radial slot outlet with square blade array RL-Q2... circular blade array RL-R2... Air distribution systems DS 86 E 09./1 with square and circular blade array Preliminary remark The radial slot outlet

More information

INTRODUCING HORIZONTAL

INTRODUCING HORIZONTAL i n t r o d u c t i o n. INTRODUCING HORIZONTAL A W I D E R A N G E O F PA N E L S, S YS T E M C O M P O N E N T S A N D A C C E S S O R I E S TO C O M B I N E F O R A W E L L D E S I G N E D S E L L I

More information

Air distribution systems. Linear whirl outlet WL...

Air distribution systems. Linear whirl outlet WL... Air distribution systems Linear whirl outlet WL... DS 0 E 1.013 Preliminary remarks Mode of operation The linear whirl outlet generates turbulent mixing ventilation. It can be installed on or in a wall

More information

Grille. Min. - max. dimensions

Grille. Min. - max. dimensions Min. - max. dimensions H L 0 00 75 00 Standard grilles are available with mm pitch within the above min. and max. sizes. Customized sizes available on request. Description is an adjustable single or double

More information

PELICAN Ceiling HF. Square extract air diffuser QUICK FACTS

PELICAN Ceiling HF. Square extract air diffuser QUICK FACTS Square extract air diffuser QUICK FACTS Perforated air diffuser front face Manages large extract airflows Flush design Designed for modular suspended ceilings Quick Access front face Can be combined with

More information

Slot diffuser. Type VSD35 2/2.6/B/3. with 35 mm wide slot

Slot diffuser. Type VSD35 2/2.6/B/3. with 35 mm wide slot 2/2.6/B/3 Slot diffuser Type VSD35 with 35 mm wide slot TROX UK Ltd Telephone +44 (0) 1842 754545 Caxton Way Telefax +44 (0) 1842 763051 Thetford e-mail trox@troxuk.co.uk Norfolk IP24 3SQ www.troxuk.co.uk

More information

SWIFTTM. Ceiling. Square ceiling air diffuser for supply air

SWIFTTM. Ceiling. Square ceiling air diffuser for supply air SWIFTTM Ceiling SWIFT Ceiling Square ceiling air diffuser for supply air Quick facts Flush design Also available in a version for extract air. Designed for modular suspended ceilings (600 x 600 mm) Quick

More information

VD1 CLC. Small Valves DIN-range with a higher k v -value

VD1 CLC. Small Valves DIN-range with a higher k v -value 0 EN - Small Valves DIN-range with a higher k v -value VD CLC Valve body made of brass, mat nickel-plated DN, DN 0 and DN Internally and externally threaded (Rp / R) conforming to ISO 7- Manual knob /

More information

Swirl diffusers, Variable swirl diffusers

Swirl diffusers, Variable swirl diffusers 0 Variable swirl diffusers SLOT IFFUSERS, ROUN UCT IFFUSERS SWIRL IFFUSERS, VARIABLE SWIRL IFFUSERS CIRCULAR IFFUSERS, SQUARE IFFUSERS VENTILATING GRILLES, VENTILATING VALVES, Variable swirl diffusers

More information

Check-Q-meter. Table of contents. Features. Functions. RE 27551/ /10 Replaces: Type FD

Check-Q-meter. Table of contents. Features. Functions. RE 27551/ /10 Replaces: Type FD Check-Q-meter RE /0.0 /0 Replaces: 09.9 Type FD Nominal size... Series ax. Operating pressure 0 bar ax. Flow 0 l/min K9/ Table of contents Contents Page Features Functions Ordering details Symbols Functional

More information

Nozzles. About Lindab. Comfort and Design. Product overview / symbols. Theory. Ceiling diffusers. Ceiling diffusers - visible.

Nozzles. About Lindab. Comfort and Design. Product overview / symbols. Theory. Ceiling diffusers. Ceiling diffusers - visible. Nozzles About Lindab Comfort and Design Product overview / symbols Theory Ceiling diffusers Ceiling diffusers - visible Plenum boxes Wall diffusers Nozzles Ventiduct Grilles Displacement diffusers VAV

More information

PELICAN Ceiling. Square ceiling air diffuser for supply air and extract air

PELICAN Ceiling. Square ceiling air diffuser for supply air and extract air Ceiling Square ceiling air diffuser for supply air and extract air Quick facts Flexible distribution pattern, yet the acoustic data remains the same One K-factor regardless of distribution pattern Designed

More information

Air distribution systems. Radial outlet RA-N2...

Air distribution systems. Radial outlet RA-N2... Air distribution systems Radial outlet RA-N... DS E 0.01 Radial outlet RA-N Preliminary remark KRANTZ KOMPONENTEN radial outlets RA-N have fixed radial vanes and are available with circular or square face.

More information

Worth noting. Introduction. Key figures. lindab architect. Picture 1. Architect Circum, Luna and Prisma.

Worth noting. Introduction. Key figures. lindab architect. Picture 1. Architect Circum, Luna and Prisma. Contact, Overview, Index Guideline heating and cooling Plexus Professor / Professor Plus Premum / Premax / Solus Architect Polaris I & S Plafond Podium Celo Cabinett Capella Carat Fasadium Atrium / Loggia

More information

Plain diffuser. Dimensions

Plain diffuser. Dimensions Dimensions ØU Ød 22 37 ØD Description is a circular diffuser with unperforated face plate and can be used for both supply and extract air. is suitable for horizontal supply of cooled air where a high impulse

More information

Made in Italy HOSE REELS CATALOGUE TECHNOLOGY FOR FLUIDYNAMICS. No. E14/A1

Made in Italy HOSE REELS CATALOGUE TECHNOLOGY FOR FLUIDYNAMICS. No. E14/A1 Made in Italy HOSE REELS CATALOGUE TECHNOLOGY FOR FLUIDYNAMICS No. E14/A1 The complete range of our products is presented in the specific catalogues: HOSE REELS CATALOGUE No. E14/A2 HOSE REELS CATALOGUE

More information

GRC. Circular egg crate grille for transfer/extract air and wall/ceiling mounting QUICK FACTS

GRC. Circular egg crate grille for transfer/extract air and wall/ceiling mounting QUICK FACTS Circular egg crate grille for transfer/extract air and wall/ceiling mounting QUICK FACTS For exhaust air 91% free area Handles large airflows Cleanable Can be used with commissioning box ALS Standard colour

More information

Cabinets G " integrated in upright Handle strip in side panel Easy solution for shortened doors

Cabinets G  integrated in upright Handle strip in side panel Easy solution for shortened doors Overview... 0 Cabinets... 1 Cabinets Wall mounted cases... 2 Accessories for cabinets and wall mounted cases... 3 Climate control... 4 Desk-top cases... 5 Subracks/ 19" chassis... 6 02002002 Front panels,

More information

Cabinets NOVASTAR. Overview Cabinets Wall mounted cases Accessories for cabinets and wall mounted cases 3.

Cabinets NOVASTAR. Overview Cabinets Wall mounted cases Accessories for cabinets and wall mounted cases 3. Overview..... 0 NOVASTAR Cabinets NOVASTAR Cabinets...... 1 Wall mounted cases........ 2 Accessories for cabinets and wall mounted cases 3 Climate control 4 Desk-top cases 5 Subracks/ 19" chassis... 6

More information

Displacement Flow Diffusers

Displacement Flow Diffusers T 1.3/1/EN/2 Displacement Flow Diffusers Types QLE QLF for low turbulence air supply TROX GmbH Telephone +9/28 /2 02-0 Telefax +9/28 /26 Heinrich-Trox-Platz e-mail trox@trox.de D0 Neukirchen-Vluyn www.troxtechnik.com

More information

Surface-mounting Thermostats ATH Type Series

Surface-mounting Thermostats ATH Type Series Page 1/9 urface-mounting Thermostats ATH eries k enclosure protection IP 54 k tested to IN EN 14597 (replacing IN 3440) Brief description Thermostats control and monitor thermal processes. Instruments

More information

Surface-mounting thermostats Series ATH

Surface-mounting thermostats Series ATH JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 E-mail: mail@jumo.net Internet: www.jumo.net

More information

GTH. Rectangular double deflection grille QUICK FACTS

GTH. Rectangular double deflection grille QUICK FACTS Rectangular double deflection grille QUICK FACTS For supply air Adjustable air deflectors Cleanable Installed using mounting frames FHB / FHA or commissioning box TRG Available in alternative colours A

More information

12.1 Product data sheet

12.1 Product data sheet Schlüter -KERDI-BOARD Substrate waterproof substrate and structural board 12.1 Product data sheet Application and Function Schlüter -KERDI-BOARD is a multifunctional tile substrate for wall areas, which

More information

CIRCO. Sound-attenuating transfer unit QUICK FACTS

CIRCO. Sound-attenuating transfer unit QUICK FACTS Sound-attenuating transfer unit QUICK FACTS Supplied in pairs For the transfer of air through a wall Fits in a circular cut opening Simple to install Mounting frame integrated into the transfer diffuser

More information

2D - STRIP ANCHOR LIFTING SYSTEM

2D - STRIP ANCHOR LIFTING SYSTEM 2D - STRIP ANCHOR LIFTING SYSTEM WWW.TERWA.COM Terwa reserves the right to make changes to the documentation at any time Page 1 OVERVIEW LIFTING CLUTCHES AND TRANSPORT ANCHOR SA-B SA-ST SA-TTU UNIVERSAL

More information

Serie B2.1. Flanged ductile iron ball valve. made in. Application fields. Shut-off valves E U R O P E. 18

Serie B2.1. Flanged ductile iron ball valve. made in. Application fields. Shut-off valves E U R O P E. 18 erie B. Flanged ductile iron ball valve BRanDOni made in E U R O P E Application fields WATER CONdITIONING GA EATING INdUTRY FIRE FIGTING www.brandoni.it erie B. eries B. valves are shut-off ball valves

More information

Introduction...COMB-2 Design Considerations and Examples...COMB-3

Introduction...COMB-2 Design Considerations and Examples...COMB-3 SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant

More information

CDD/CDR. Circular ceiling diffuser for supply air QUICK FACTS

CDD/CDR. Circular ceiling diffuser for supply air QUICK FACTS Circular ceiling diffuser for supply air QUICK FACTS Spread pattern can be shielded Used with commissioning box ALS Cleanable Adjustable slot Perforated diffuser face = CDD Non-perforated diffuser face

More information

PRO-CLEAN STRATIFIED TANK

PRO-CLEAN STRATIFIED TANK PO-CLEAN STATIFIED TANK PODUCT DESCIPTION Pro-Clean stratified tank with spherical exchanger connection High-quality, multifunctional stratified tank made of steel (S J) for hot-water operation and domestic

More information

12.1 Schlüter -KERDI-BOARD

12.1 Schlüter -KERDI-BOARD Innovative profiles 12.1 Schlüter -KERDI-BOARD S u b s t r a t e UNIVERSAL STRUCTURAL PANEL, BONDED WATERPROOFING Application and Function Schlüter -KERDI-BOARD is a multifunctional tile substrate for

More information

VDN2.. VEN2.. VUN2.. Radiator valves. Building Technologies HVAC Products ACVATIX TM. NF norm, for 2-pipe heating systems

VDN2.. VEN2.. VUN2.. Radiator valves. Building Technologies HVAC Products ACVATIX TM. NF norm, for 2-pipe heating systems 06 EN - Straight valves VDN.. Angle valves VEN.. Reverse angle valves VUN.. ACVATIX TM Radiator valves NF norm, for -pipe heating systems VDN.. VEN.. VUN.. Valve bodies made of brass, mat nickel-plated

More information

Variable swirl diffusers

Variable swirl diffusers Swirl diffusers, Variable swirl diffuser OD- Application Diffuser is designed for air conditioning of rooms with floor to ceiling highs of to 0 m and high induction requirements. It is suitable for large

More information

Air distribution systems. Jet nozzle DW-N2... Swivel jet nozzle DW-V2... Twist nozzle DW-V2-...-DR

Air distribution systems. Jet nozzle DW-N2... Swivel jet nozzle DW-V2... Twist nozzle DW-V2-...-DR Air distribution systems Jet nozzle DW-N... Swivel jet nozzle DW-V... Twist nozzle DW-V-...-DR DS E 01. Jet nozzle and twist nozzle Preliminary remarks Jet nozzle DW N Swivel jet nozzle DW V Twist nozzle

More information

Conductivity sensor for hygienic applications

Conductivity sensor for hygienic applications Conductivity sensor for hygienic applications Type 8221 can be combined with Perfect for demanding applications in the hygienic industry (CIP and SIP compatible) Variants available for usage over a wide

More information

12.1 Product data sheet

12.1 Product data sheet Schlüter -KERDI-BOARD Substrate universal structural panel, bonded waterproofing 12.1 Product data sheet Application and Function Schlüter -KERDI-BOARD is a multifunctional tile substrate for wall areas,

More information

Krantz. Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems

Krantz. Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems Krantz Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems DS E 01.18 Variable twist outlet with guide ring or jet straightener Preliminary remarks The variable

More information

PHOS 15 LED PROJECTOR

PHOS 15 LED PROJECTOR PHOS 15 LED PROJECTOR SPECIFICATIONS Item:.. PHOS 15 Body:.... Aluminium Available Colours:... White / Black / Silver Weight:.... 1.9 kg On / Off Switch:..... Not Available Environmental Conditions:.....

More information

Turbine Meter TRZ 03 PRODUCT INFORMATION. Reliable Measurement of Gas

Turbine Meter TRZ 03 PRODUCT INFORMATION. Reliable Measurement of Gas Turbine Meter TRZ 0 PRODUCT INFORMATION Reliable Measurement of Gas TURBINE METER TRZ 0 Method of operation, Construction Method of operation The TRZ 0 turbine meter is a flow meter suitable for gas measurement

More information

Nozzle diffuser. Dimensions

Nozzle diffuser. Dimensions Nozzle diffuser GTI Dimensions Installation Ød Description GTI is a flexible supply air nozzle that is suitable for ventilation of large areas. The nozzle can be used for both heated and cooled air and

More information

KONTEC KS 20 KS 21 KS 10 KS 11 KS 10 KS 11 KS 21 KS 20. model overview / connection dimensions. KS models vertical design

KONTEC KS 20 KS 21 KS 10 KS 11 KS 10 KS 11 KS 21 KS 20. model overview / connection dimensions. KS models vertical design 288 model overview / connection dimensions KS models vertical design KS 10 26 KS 11 26 KS 20 47 KS 21 93 47 93 68 68 10, 1800,, KS 10 KS 11 KS 20 KS 21 68 68 93 93 142-862 5 5 5 5 5 5 5 5 height 10 1800

More information

WISE Damper. Active damper for Swegon s WISE System for demand-controlled ventilation QUICK FACTS

WISE Damper. Active damper for Swegon s WISE System for demand-controlled ventilation QUICK FACTS Active damper for Swegon s WISE System for demand-controlled ventilation QUICK FACTS Variable or constant flow regulation or constant pressure regulation Wireless communication via radio Integrated sensor

More information

Supply air beam. Contact, Overview, Index. Guideline heating and cooling. Plexus. Professor / Professor Plus. Premum / Premax / Solus.

Supply air beam. Contact, Overview, Index. Guideline heating and cooling. Plexus. Professor / Professor Plus. Premum / Premax / Solus. Contact, Overview, Index Guideline heating and cooling Plexus Professor / Professor Plus Premum / Premax / Architect Polaris I & S Plafond Podium Celo Cabinett Capella Carat Fasadium Atrium / Loggia Regula

More information

Linear ceiling diffuser

Linear ceiling diffuser L-0--01e Linear ceiling diffuser Type LDD / LDDL Contents Realisation Application Safety instructions Contents Realisation Application Safety instructions Dimensions 3 Dimensions Installation Quick selection

More information

Air distribution systems. Adjustable radial outlet RA-V...

Air distribution systems. Adjustable radial outlet RA-V... Air distribution systems Adjustable radial outlet RA-V... DS E 0.2013 Construction design Preliminary remarks KRANTZ KOMPONENTEN has developed its wellknown, successful radial outlet into an adjustable

More information

FORMWORK SAVINGS ADAPTABILITY LIGHT WEIGHT ECONOMICAL ALUMINIUM SLAB FORMWORK. BV Cert

FORMWORK SAVINGS ADAPTABILITY LIGHT WEIGHT ECONOMICAL ALUMINIUM SLAB FORMWORK. BV Cert FORMWORK SAVINGS ADAPTABILITY LIGHT WEIGHT ECONOMICAL ALUMINIUM SLAB FORMWORK BV Cert. 6150814 Dalphi Economical aluminium slab formwork 2 FORMWORK The economical, high-performance Dalphi floor formwork

More information

Linear diffuser. Description

Linear diffuser. Description A C B + D Description is a rectangular linear diffuser in aluminium. is suitable for both supply and exhaust air. is equipped with air guide baffles, making it possible to use for horizontal supply air.

More information

VX25 Enclosure System. Technical documentation PE conductor connection, current carrying capacity

VX25 Enclosure System. Technical documentation PE conductor connection, current carrying capacity VX Enclosure System Technical documentation PE conductor connection, current carrying capacity Enclosure system VX Contents Contents. General remarks. Introduction. Notes on the design of the earthing

More information

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

Chapter 11: Heat Exchangers. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 11: Heat Exchangers Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives When you finish studying this chapter, you should be able to: Recognize numerous types of

More information

laminated on both sides for effective anchoring in the tile adhesive.

laminated on both sides for effective anchoring in the tile adhesive. Schlüter -KERDI-DRAIN Drainage floor drains for bonded waterproofing assemblies 8.2 Product data sheet Application and function Schlüter -KERDI-DRAIN is a floor drain system for the easy and reliable connection

More information

MODEL: WB009GMFI19HLD (120V) Wall Mount DC Inverter Fan Coil Unit 9,000 BTUH

MODEL: WB009GMFI19HLD (120V) Wall Mount DC Inverter Fan Coil Unit 9,000 BTUH MODEL: WB009GMFI19HLD (120V) Wall Mount DC Inverter Fan Coil Unit 9,000 BTUH No. Part Name Quantity BOM code List Price Remark 1 Panel assembly 1 201132890609 2 Air filter 2 201132890704 5 Display box

More information

Step Impulse Diffuser Model SIA

Step Impulse Diffuser Model SIA Step Impulse Diffuser Model SIA Ferdinand Schad KG Steigstraße 25-27 D-78600 Kolbingen Phone +49 (0) 74 63-980 - 0 Fax +49 (0) 74 63-980 - 200 info@schako.de www.schako.de Step Impulse Diffuser Model SIA

More information

CDD/CDR. Single cone ceiling diffusers for supply air. Quick facts. Quick guide CDD/CDR A I R F L O W - S O U N D L E V E L

CDD/CDR. Single cone ceiling diffusers for supply air. Quick facts. Quick guide CDD/CDR A I R F L O W - S O U N D L E V E L Single cone ceiling diffusers for supply air Quick facts Spread pattern can be shielded Used with commissioning box ALS Cleanable Adjustable slot Perforated diffuser face = CDD Imperforated diffuser face

More information

Multi-cone diffuser. Dimensions

Multi-cone diffuser. Dimensions Dimensions Vertical Ød 8 Max. H ØU ØD Horizontal Ød Description is an adjustable circular multi-cone diffuser, which is typically used for supply air. The diffuser can be switched between horizontal and

More information

Use. Worth noting. Key figures. Installation. lindab fasadium

Use. Worth noting. Key figures. Installation. lindab fasadium Contact, Overview, Index Guideline heating and cooling Plexus Professor / Professor Plus Premum / Premax / Solus Architect Polaris I & S Plafond Podium Celo Cabinett Capella Carat Atrium / Loggia Regula

More information

Krantz Components. Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems

Krantz Components. Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems Variable twist outlet with guide ring DD-VL... jet straightener DD-VG... Air distribution systems DS E 01. with guide ring or jet straightener Preliminary remarks The variable twist outlet with guide ring

More information

E 094 E 103 E 143. Tank top mounting Connection up to G1 Nominal flow rate up to 135 l/min e

E 094 E 103 E 143. Tank top mounting Connection up to G1 Nominal flow rate up to 135 l/min e R e t u r n F i l t e rs E 094 E 103 E 143 Tank top mounting Connection up to G1 Nominal flow rate up to 135 l/min 20.30-5e D e s c r i p t i o n Application In the return line circuits of hydraulic systems.

More information

ED 701 General Industry Pressure Transmitter

ED 701 General Industry Pressure Transmitter ED 701 General Industry Pressure Transmitter Standard industrial process connections Complete range of electrical connections 4... 20 ma and Voltage outputs Accuracy: 0.1%, 0.2% and 0.4% FS Quick response

More information

AIR PREPARATION. ELECTRONICALLY CONTROLLED PRESSURE REGULATING VALVE (PROPORTIONAL PRESSURE REGULATING VALVE) SERIES control

AIR PREPARATION. ELECTRONICALLY CONTROLLED PRESSURE REGULATING VALVE (PROPORTIONAL PRESSURE REGULATING VALVE) SERIES control AIR PREPARATION ELECTRONICALLY CONTROLLED PRESSRE REGLATING ALE (PROPORTIONAL PRESSRE REGLATING ALE) SERIES control Description Abb. Port size Recommended Type Data Sheet No. flow (l/min)* airfit tecno

More information

FRB. Exposed passive chilled beam for suspended installation

FRB. Exposed passive chilled beam for suspended installation Exposed passive chilled beam for suspended installation QUICK FACTS FRB is a passive chilled beam for comfort cooling especially designed for visible/suspended installation in the room. High cooling capacity,

More information

Valve Supply and exhaust air

Valve Supply and exhaust air IRY Dimensions Description The valve is designed for installation at a wall or in a ceiling. It can be used for new-build and for replacement. Its smart grip function ensures an easy installation. Its

More information

Main Catalogue. Edition 23, chapter minirack: Phase-out product!

Main Catalogue. Edition 23, chapter minirack: Phase-out product! Edition 23, chapter minirack: Phase-out product! Overview... 0 Cabinets... 1 G Cabinets G Wall mounted cases... 2 Accessories for cabinets and wall mounted cases... 3 Climate control... 4 Desk-top cases...

More information

E X - C O N T R O L U N I T S A N D C O N T R O L S T A T I O N S

E X - C O N T R O L U N I T S A N D C O N T R O L S T A T I O N S E X - C O N T R O L U N I T S A N D C O N T R O L S T A T I O N S EX- CONTROL UNITS AND CONTROL STATIONS EX- INSTALLATION SWITCH.. EX- CONTROL STATIONS INDIVIDUAL EX- CONTROL STATIONS.. 0 EX- CONTROL AND

More information

UvA-DARE (Digital Academic Repository) Converting lignin to aromatics: step by step Strassberger, Z.I. Link to publication

UvA-DARE (Digital Academic Repository) Converting lignin to aromatics: step by step Strassberger, Z.I. Link to publication UvA-DARE (Digital Academic Repository) Converting lignin to aromatics: step by step Strassberger, Z.I. Link to publication Citation for published version (APA): Strassberger, Z. I. (2014). Converting lignin

More information

NFRC THERMAL TEST SUMMARY REPORT January 27, 1999 Test Specimen

NFRC THERMAL TEST SUMMARY REPORT January 27, 1999 Test Specimen * This is not the original copy of the test report if you would like an original copy, please contact our East Brunswick office or the NCTL to request a copy. ALL SEASONS DOOR & WINDOW, INC. REPORT NO:

More information

8.6 Product data sheet

8.6 Product data sheet Schlüter -KERDI-SHOWER Drainage floor level showers 8.6 Product data sheet Application and Function Schlüter -KERDI-SHOWER is a modular system for the construction of floor level showers with ceramic tiles.

More information

CNA-CNB. Centrifugal fans

CNA-CNB. Centrifugal fans NA-NB entrifugal fans Product facts Product Single-inlet low-pressure fans with backward-curved blades. Use In industrial ventilation systems for uncontaminated, non-corrosive air, max. 70 º, where a low

More information

Solenoid valves Type EVR 2 g 40 NC/ NO New EVR 6 with Steel cover design

Solenoid valves Type EVR 2 g 40 NC/ NO New EVR 6 with Steel cover design MAKING MODERN LIVING POSSIBLE Technical brochure Solenoid valves EVR 2 g 40 NC/ NO New with Steel cover design EVR is a direct or servo operated solenoid valve for liquid, suction, and hot gas lines with

More information

series FLOOR

series FLOOR series FLOOR www.koolair.com Floor Series 3 DSA, DSA-PR, DSA-HV and DF-CP-MT Floor swirl diffusers CONTENTS DSA / DSA-PR / DSA-HV diffusers 4 Models and dimensions 5 DSA Selection tables 6 DSA Selection

More information

Circular duct grille

Circular duct grille Dimensions B+0 A+0 A B Description is a rectangular ventilation grille with vertical adjustable bars for direct installation in circular ducts. The grille can be used for both supply and exhaust air. The

More information

DIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER: NEW MILLENNIUM BUILDING SYSTEMS, LLC

DIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER: NEW MILLENNIUM BUILDING SYSTEMS, LLC 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2657 Reissued 05/2017 This report is subject to renewal 03/2018. DIVISION: 05 00 00 METALS SECTION:

More information

DBQ Painted four four-way square square diffuseurs M A D E L

DBQ Painted four four-way square square diffuseurs M A D E L Painted four-way square diffuseurs MADEL The four-way square diffusers meet the functional and architectural requirements of modern updated locations. Its geometrical shape, fits perfectly in the style

More information

Amphenol C 091 A/B/D. Circular Connectors. Amphenol-Tuchel Electronics GmbH

Amphenol C 091 A/B/D. Circular Connectors. Amphenol-Tuchel Electronics GmbH Amphenol C 091 A/B/D Circular Connectors Amphenol-Tuchel Electronics GmbH General information These connectors are designed and produced in conformity with the low-voltage directive (/3/EWG) respectively

More information

40 CD RANGE FLUSH-MOUNTING DISTRIBUTION BOARDS AND ENCLOSURES

40 CD RANGE FLUSH-MOUNTING DISTRIBUTION BOARDS AND ENCLOSURES DISTRIBUTION BOARDS FLUSH-MOUNTING DISTRIBUTION BOARDS GWTEST SOFTWARE (see page 322) Complementary system items Ordinary installation - protected flush mounting DISTRIBUTION / JUNCTION Protection devices...

More information

TOWEL RAILS. Serie Comfort PRICE LIST

TOWEL RAILS. Serie Comfort PRICE LIST TOWE RAS Serie Comfort PRCE ST 2 0 1 7 Cordivari company has a proven industrial tradi on and is now one of the most important manufacturers in the hea ng and plumbing industry in taly. Founded in 1972

More information

Mechanical flow-rate controllers

Mechanical flow-rate controllers L D L D L D Mechanical flow-rate controller MRP-1 (Circular) Description With the circular air flow controllers with automated action, the air flow rate is controlled via an asymmetrical control flap pivoting

More information

Section Installation accessories. > UNION Series > TIES Series > FIXO Series > CABLO Series > FASTY Series > RAILDIN Series

Section Installation accessories. > UNION Series > TIES Series > FIXO Series > CABLO Series > FASTY Series > RAILDIN Series Section > UNION Series > TIES Series > FIXO Series > CABLO Series > FASTY Series > RAILDIN Series 22 23 > CABLE GLANDS WITH DEVICE TO PREVENT ANY UNSCREWING UNION Series B (*) IP8 (1 bar) C A in mm A B

More information

Solar Flat Plate Thermal Collector

Solar Flat Plate Thermal Collector Solar Flat Plate Thermal Collector INTRODUCTION: Solar heater is one of the simplest and basic technologies in the solar energy field. Collector is the heart of any solar heating system. It absorbs and

More information

THREE HOLE SPLICE CLEVIS FOR B52 Standard finishes: ZN, GRN Wt./C 126 Lbs. (57.1 kg)

THREE HOLE SPLICE CLEVIS FOR B52 Standard finishes: ZN, GRN Wt./C 126 Lbs. (57.1 kg) CLEVIS FITTINGS B169 TWO HOLE SPLICE Wt./C 84 Lbs. (38.1 kg) B168 THREE HOLE SPLICE Wt./C 126 Lbs. (57.1 kg) B167 Wt./C 178 Lbs. (80.7 kg) 3 1 /2 (88.9) B170 TWO HOLE SPLICE Wt./C 123 Lbs. (55.8 kg) 5

More information

Nylon oil filler and air breather filler caps

Nylon oil filler and air breather filler caps Series TP 0 Dimensions 6 Bayonet G / TP0 (Materials) - Cover/ringnut: Nylon - Filter element: Impregnated paper Polyurethane - Pressurisation valve: Nylon Galvanised Steel - Seal: Reservoir holes - Flange:

More information