CAUTION. All safety information must be followed as provided in this Technical Sheet and in Service Manual RS

Transcription

1 peed Queen Domestic asher echnical nformation 0 V, 0 Hz Models Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. efer to ervice Manual for detailed installation, operating, testing, troubleshooting, and disassembly instructions. efer to arts Manual 0007 for part number information.! C ll safety information must be followed as provided in this echnical heet and in ervice Manual ! o avoid risk of electrical shock, personal injury, or death, disconnect power to unit and discharge capacitor before servicing, unless Models 70 Models 70 ower ource ash cyles Voltage C 0 VC ater temperatures mperage (ingle nit) 0 ater level Variable requency 0 Hz eatures Motor horsepower / teady pin alance ystem X eceptacle -0 elf-cleaning lint filter X lug -0 elf-adjusting rear leveling legs X Dimensions 0 gitation stroke X Cabinet ri ction wash system X Height overall abric softener dispenser X Height of cabinet xtra rinse X idth 7 Motor speed speed Depth pin speed (revolutions per minute) 0 / 7 rpm Clearance washer lid 7 / gitation speed (strokes per minute) eight High 9 spm Crated 9 lbs. Medium spm ugust ev. 0

2 Component esting nformation! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless llustration Component est rocedure esults 000 emperature switch Disconnect wires from component to properly measure the resistance of the component. lace switch in the following positions and measure across the terminals below: Hot / Cold - > Ω arm / arm -, -, - -, -, - > Ω arm / Cold -, -, - > Ω Cold / Cold - > Ω Mixing valve Measure resistance of terminals on each valve. esistance across each valve. pproximately 000 Ω ± 0% imer Verify input and output voltage is present. ee timing sequence chart for functional description of the component. Verify wiring is correctly connected to the timer. 000 ressure switch Do not disconnect the pressure hose from pressure switch to perform measurements. Measure resistance across the following terminals on the pressure switch: erminal to erminal to efer to wiring diagram/schematic for correct contacts. ir pressure that actuates switch is determined by the water level of the tub. Continuity (no pressure) Continuity (pressure) 0000 id switch Disconnect wire terminals from switch. est terminals with switch closed. est terminals with switch open. Continuity nfinite > Ω MΩ 000 ev. 0 ugust 000

3 Component esting nformation! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless llustration Component est rocedure esults 0 ocker switch Measure resistance of switch (xtra inse) positions: Continuity > Ω Closed ( position) nfinite MΩ pen ( position) rake pad kit f washtub does not stop spinning within seven seconds after opening loading door. f brake pads make noises Motor ype of motor: wo speed eplace all three brake pads. pply a thin layer of silicone (9) on pads, see ervice ulletin Q ee following section nternal Motor Diagram and chematic for correct wiring contacts Drain pump Verify drain pump is not clogged or damaged. emove clog and verify proper operation. eplace drain pump if damaged. 000 ransmission assembly ype of transmission: 0 rpm xternally identical, must be identified by part number. f transmission locks-up, replace. 000 Drive belt ype of drive belt: 0 rpm efer to arts Manual, to verify which drive belt and pulley size is required. efer to arts Manual for proper pulley size. ugust ev. 0

4 nternal Motor Diagram and chematic! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless ne or wo peed Motors tart erminals Continuity exists between switch terminal and ed wire. Y Manually depress actuator. Continuity broken between switch terminal and ed wire. noperative start switch. eplace switch. Y Continuity exists between switch terminal and ed wire. High peed erminals Y Manually depress actuator. Continuity broken between switch terminal and ed wire. noperative high speed switch. eplace switch. Y ow peed erminals Continuity broken between switch terminal and Violet wire. Y Manually depress actuator. Continuity exists between switch terminal and Violet wire. noperative low speed switch. eplace switch. Y Motor switch checks. tart inding - ohms between rown wire and ed wire. noperative start winding. eplace motor. Y High peed inding - ohms between lue wire and Yellow wire. noperative high speed winding. eplace motor. Y ow peed inding - ohms between Yellow wire and Violet wire. noperative low speed winding. eplace motor. Y rotector Continuity exists between Yellow wire and hite wire. noperative common lead. eplace motor. Y ll motor windings checks. 000 ev. 0 ugust 000

5 nternal Motor Diagram and chematic! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless ire harness connection block Y hite rown Yellow lue Violet ed Y hite Yellow rown Yellow M M lue ed Violet verload protector ux. Motor ssembly (two speed motor) ugust ev. 0

6 iring Diagram and chematic! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless CC DM D C HD M H V H 9 Y / D / 0 D/ M. CH M M H/D Y/ / /.. 7 H/ X M /H H/ X CH 0 V CC. H D D C CC /Y /Y D /Y Y H/D 9 9 H/D Y CH / /Y D CH CM. V H/D 7 H D D M = 7 7 V H 7 CD MX VV H CD D H M 000 ev. 0 ugust 000

7 iring Diagram and chematic! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless CHMC 0 V.C. 0 HZ X M. CH H CD M M M CD CD CD X CH CH D CH.. M. CH H V MX VV CD H Y = CD M M H M M M 7 HH DC M ugust ev. 0

8 imer Cycle Chart! o avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing, unless C M 0 0 D H V- V- CD -V H -H M M M- M H-M M-H, Y - X. -X - CH C M D D M CH H M H: D Y - H H M H: X M M M X DC X HD H ailure to install, maintain, and/or operate this machine according to manufacture's instructions may result in conditions which can produce bodily injury and/or property damage. H MCH MCD D M H : D :,,7;,,7;, CD :,00,; 99, H D CC CC CD. 000 X H H M M V V H Y/ / / H / 9 7 H/ 0 V H/ D 7 H/ X / 0 D/ X 9 Y D / 000 ev. 0 ugust 000