HCC4543B HCF4543B BCD-TO-7 SEGMENT LATCH/DECODER/LCD DRIVER HCC/HCF4543B

Size: px

Start display at page:

Download "HCC4543B HCF4543B BCD-TO-7 SEGMENT LATCH/DECODER/LCD DRIVER HCC/HCF4543B"

Ronald Campbell
6 years ago
Views:

1 HCC4543B HCF4543B BCD-TO-7 SEGMENT LATCH/DECODER/LCD DRIER DISPLAY BLANKING OF ALL ILLEGAL INPUT COMBINATIONS LATCH STORAGE OF CODE CAPABILITY OF DRIING TWO LOW POWER TTL LOADS, TWO HTL LOADS, OR ONE LOW POWER SCHOTTKY LOAD OER THE FULL RATED-TEMPERATURE RANGE PIN-FOR-PIN REPLACEMENT FOR THE HCF4056B (with pin 7 tied to SS ) DIRECT LED DRIING CAPABILITY 0% TESTED FOR QUIESCENT CURRENT AT 20 MAXIMUM INPUT CURRENT OF 1A AT 18 OER FULL PACKAGE-TEMPERATURE RANGE ; 0nA AT 18 AND 25 C NOISE MARGIN (full package-temperature range) = 1 AT DD =5 2 AT DD = 2.5 AT DD = 5-, -, AND - PARAMETRIC RATINGS Applications : INSTRUMENT DISPLAY DRIER DASHBOARD DISPLAY DRIER COMPUTER/CALCULATOR DISPLAY DRIER TIMING DEICE DRIER (clocks, watches, timers) EY (Plastic Package) F (Ceramic Frit Seal Package) M1 C1 (Micro Package) (Plastic Chip Carrier) ORDER CODES : HCC4543 BF HCF4543 BM1 HCF4543 BEY HCF4543 BC1 PIN CONNECTION (top view) DESCRIPTION The HCC/HCF4543B is a BCD-to-seven segment latch/decoder/driver designed primarily for liquidcrystal display (LCD) applications. It is also capable of driving light emitting diode (LED), incandescent, gas-discharge, and fluorescent displays. This device is functionally similar to and serves as direct replacement for the HCF4056B when pin 7 is connected to SS. It differs from the HCF4056B in that it has a display blanking capability instead of a level-shifting function and requires only one power supply. When the HCF4056B is used in the level shifting mode, two power supplies are required. When the HCF4543B is used for LCD applications, a square wave must be applied to the PHASE input and the backplane of the LCD device. For LED applications a logic 1 is required at the PHASE input for common-cathode devices ; a logic 0 is required for common-anode devices (see truth table). December /12

2 ABSOLUTE MAXIMUM RATINGS Symbol Parameter alue Unit DD * Supply voltage : HCC Types HCF Types LOGIC DIAGRAM (1/2 of device shown) 0.5 to to 18 i Input oltage 0.5 to DD II DC Input Current (any one input) ± ma Total Power Dissipation (per package) 200 mw Dissipation per Output Transistor for Top = Full Package-temperature Range 0 mw P tot T op Operating Temperature : HCC Types HCF Types 55 to to+85 Tstg Storage Temperature 65 to + 0 C * All oltage alues are referred to SS pin voltage. C C RECOMMENDED OPERATING CONDITIONS Symbol Parameter alue Unit DD Supply oltage : HCC Types HCF Types 3to+18 3to+ I Input oltage 0 to DD Top Operating Temperature : HCC Types HCF Types 55 to to+85 C C 2/12

3 TRUTH TABLE INPUT CODE OUTPUT STATE DISPLAY LD BI Ph* D C B A a b c d e f g CHARACTER X 1 0 X X X X Blank Blank Blank Blank Blank Blank X X X X ** ** X = Don t care. = Above combinations * = For liquid-crystal readouts, apply a square wave to Ph. For common cathode LED readouts, select Ph = 0. For common anode LED readouts, select Ph = 1. ** = Depends upon the BCD code previously applied when LD = 1. Inverse of Output Combinations Above Display as above 3/12

4 STATIC ELECTRICAL CHARACTERISTICS Symbol I L OH OL IH IL I OH IOL I IH,I IL Parameter Quiescent Current Output High oltage Output Low oltage Input High oltage Input Low oltage Output Drive Current Output Sink Current Input Leakage Current HCC Types HCF Types HCC Types HCF Types HCC Types HCF Types I () Test Conditions O () IO (µa) DD () alue T Low 25 C T High Min. Max. Min. Typ. Max. Min. Max. 0/ / / / / / / /5 < / < / < /0 < /0 < /0 < /4.5 < /9 < /13.5 < /0.5 < /1 < /1.5 < / / / / / / / / / / / / / / HCC types 0/18 18 ± 0.1 ± 5 ± 0.1 ± 1 Any Input HCF types 0/ ± 0.3 ± -5 ± 0.3 ± 1 * T Low = 55 C for HCC device : 40 C for HCF device. * T High = C for HCC device : + 85 C for HCF device. The Noise Margin for both 1 and 0 level is : 1 min. with DD = 5, 2 min. with DD =, 2.5 min. with DD =. Unit µa ma ma µa 4/12

5 DYNAMIC ELECTRICAL CHARACTERISTICS (T amb =25 C, C L = 50pF, R L = 200kΩ, typical temperature coefficient for all DD values is 0.3%/ C, all input rise and fall time = 20ns) Symbol Parameter Test Conditions DD () tphl Propagation Delay Time 5 tplh 5 tthl Transition Time 5 ttlh 5 twh Latch Disable Pulse Width 5 tsu Address Setup Time 5 th Address Hold Time 5 Limits All packages Min. Typ. Max. CIN Input Capacitance Any Input pf Unit ns BCD-to-seven-segment latch/decoder/driver functional diagram 5/12

6 Typical Output Low (sink) Current Characteristics. Minimum Output Low(sink) Current Characteristics. Typical Transition Time as a Function of Load Capacitance Typical Propagation Delay Time as a Function of Load Capacitance Typical Dinamic Power Dissipation as a Function of Frequency 6/12

7 Input oltage Test Circuit. Quiescent Device Current Test Circuit. Input-leakage -current Test Circuit. 7/12

8 Plastic DIP16 (0.25) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. a B b b D E e e F I L Z P001C 8/12

9 Ceramic DIP16/1 MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A B D E e F G H L M N P Q P053D 9/12

10 SO16 (Narrow) MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A a a b b C c1 45 (typ.) D E e e F G L M S 8 (max.) P013H /12

11 PLCC20 MECHANICAL DATA DIM. mm inch MIN. TYP. MAX. MIN. TYP. MAX. A B D d d E e e F G M M P027A 11/12

12 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specificationsmentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronicsproducts are not authorized foruse ascritical componentsin life support devices or systems without express written approval of SGS-THOMSON Microelectonics SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 12/12

HCC/HCF4042B QUAD CLOCKED D LATCH

HCC/HCF4042B QUAD CLOCKED D LATCH QUAD CLOCKED D LATCH CLOCK POLARITY CONTROL Q AND Q OUTPUTS COMMON CLOCK LOW POWER TTL COMPATIBLE STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED TO 20 FOR HCC DEICE 5, 10,