Chapter kn m/kg Ans kn m/kg Ans. 187 kn m/kg Ans.

Size: px
Start display at page:

Download "Chapter kn m/kg Ans kn m/kg Ans. 187 kn m/kg Ans."

Transcription

1 Chapter -1 From Tables A-0, A-1, A-, and A-4c, (a) UNS G1000 HR: S ut = 80 (55) MPa (kpsi), S yt = 10 (0) MPa (kpsi) Ans. (b) SAE 1050 CD: S ut = 690 (100) MPa (kpsi), S yt = 580 (84) MPa (kpsi) Ans. (c) AISI 1141 Q&T at 540 C (1000 F): S ut = 896 (10) MPa (kpsi), S yt = 765 (111) MPa (kpsi) Ans. (d) 04-T4: S ut = 446 (64.8) MPa (kpsi), S yt = 96 (4.0) MPa (kpsi) Ans. (e) Ti-6Al-4V annealed: S ut = 900 (10) MPa (kpsi), S yt = 80 (10) MPa (kpsi) Ans. - (a) Maximize yield strength: Q&T at 45 C (800 F) Ans. (b) Maximize elongation: Q&T at 650 C (100 F) Ans. - Conversion of kn/m to kg/ m multiply by 1(10 ) / 9.81 = 10 AISI 1018 CD steel: Tables A-0 and A-5 S y 70( 10 ) 47.4 kn m/kg Ans. ρ = 76.5( 10) = 011-T6 aluminum: Tables A- and A-5 S y 169( 10 ) 6. kn m/kg Ans. ρ = 6.6( 10) = Ti-6Al-4V titanium: Tables A-4c and A-5 S y 80( 10 ) 187 kn m/kg Ans. ρ = 4.4( 10) = ASTM No. 40 cast iron: Tables A-4a and A-5.Does not have a yield strength. Using the ultimate strength in tension S ut 4.5( 6.89)( 10 ) 40.7 kn m/kg Ans ρ = 70.6( 10) = -4 AISI 1018 CD steel: Table A-5 6 E 0.0( 10 ) 6 106( 10 ) γ = 0.8 in Ans. 011-T6 aluminum: Table A-5 6 E 10.4( 10 ) 6 106( 10 ) γ = in Ans. Shigley s MED, 10 th edition Chapter Solutions, Page 1/

2 Ti-6Al-6V titanium: Table A-5 6 E 16.5( 10 ) 6 10( 10 ) γ = in Ans. No. 40 cast iron: Table A-5 6 E 14.5( 10 ) ( 10 ) γ = 0.60 in Ans. -5 E G G(1 + v) = E v = G Using values for E and G from Table A-5, 0.0 ( 11.5) Steel: v = = 0.04 Ans. ( 11.5) The percent difference from the value in Table A-5 is = = 4.11 percent Ans. ( ) Aluminum: v = = 0. Ans. (.90) The percent difference from the value in Table A-5 is 0 percent Ans. Beryllium copper: ( ) ( ) v = = 0.86 Ans. 7.0 The percent difference from the value in Table A-5 is = = 0.51 percent Ans. ( ) Gray cast iron: v = = 0.08 Ans. ( 6.0) The percent difference from the value in Table A-5 is = = 1.4 percent Ans (a) A 0 = π (0.50) /4 = in, σ = P i / A 0 Shigley s MED, 10 th edition Chapter Solutions, Page /

3 For data in elastic range, = l / l 0 = l / l l l0 l A0 For data in plastic range, ò = = = 1 = 1 l0 l0 l0 A On the next two pages, the data and plots are presented. Figure (a) shows the linear part of the curve from data points 1-7. Figure (b) shows data points 1-1. Figure (c) shows the complete range. Note: The exact value of A 0 is used without rounding off. (b) From Fig. (a) the slope of the line from a linear regression is E = 0.5 Mpsi Ans. From Fig. (b) the equation for the dotted offset line is found to be σ = 0.5(10 6 ) (1) The equation for the line between data points 8 and 9 is σ = 7.60(10 5 ) () Solving Eqs. (1) and () simultaneously yields σ = 45.6 kpsi which is the 0. percent offset yield strength. Thus, S y = 45.6 kpsi Ans. The ultimate strength from Figure (c) is S u = 85.6 kpsi Ans. The reduction in area is given by Eq. (-1) is A0 A f R = ( 100) = ( 100) = 45.8 % Ans. A Data Point P i l, A i σ Shigley s MED, 10 th edition Chapter Solutions, Page /

4 Stress (psi) y =.05E+07x E Strain (a) Linear range Series1 Linear (Series1) Stress (psi) Y (b) Offset yield Strain Stress (psi) U Strain (c) Complete range Shigley s MED, 10 th edition Chapter Solutions, Page 4/

5 (c) The material is ductile since there is a large amount of deformation beyond yield. (d) The closest material to the values of S y, S ut, and R is SAE 1045 HR with S y = 45 kpsi, S ut = 8 kpsi, and R = 40 %. Ans. -7 To plot σ true vs.ε, the following equations are applied to the data. P σ true = A Eq. (-4) l ε = ln for 0 l in (0 P 8400 lbf ) l 0 A0 ε = ln for l > in ( P > lbf ) A π (0.50) where A0 = = in 4 The results are summarized in the table below and plotted on the next page. The last 5 points of data are used to plot log σ vs log ε The curve fit gives m = 0.06 log σ 0 = σ 0 = 15. kpsi Ans. For 0% cold work, Eq. (-14) and Eq. (-17) give, A = A 0 (1 W) = (1 0.) = in A ε = = = A ln ln 0.1 m 0.06 Eq. (-18): S y = σ 0ε = 15.(0.1) = kpsi Ans. Eq. (-19), with S = 85.6 from Prob. -6, u Su 85.6 S u = = = 107 kpsi Ans. 1 W 1 0. Shigley s MED, 10 th edition Chapter Solutions, Page 5/

6 P l A ε σ true log ε log σ true Shigley s MED, 10 th edition Chapter Solutions, Page 6/

7 -8 Tangent modulus at σ = 0 is σ E = = 5( 10 ) psi ò ( ) Ans. At σ = 0 kpsi Shigley s MED, 10 th edition Chapter Solutions, Page 7/

8 E 0 )( 10 ) ( 1.5 1)( ) ( 6 19) (10 - ) σ (kpsi) ( ) = psi Ans W = 0.0, (a) Before cold working: Annealed AISI 1018 steel. Table A-, S y = kpsi, S u = 49.5 kpsi, σ 0 = 90.0 kpsi, m = 0.5, f = 1.05 After cold working: Eq. (-16), u = m = 0.5 A0 Eq. (-14), A = i 1 W = = A0 Eq. (-17), ε i = ln = ln1.5 = 0. < ε u A Eq. (-18), Eq. (-19), (b) Before: i ( ) 0.5 S m y = σ 0ε i = = 61.8 kpsi Ans. 9% increase Ans. S S 49.5 u = u 61.9 kpsi Ans. 1 W = = 5% increase Ans. Su 49 S = y = After: S u 61.9 = = 1.00 S 61.8 Lost most of its ductility. -10 W = 0.0, (a) Before cold working: AISI 11 HR steel. Table A-, S y = 8 kpsi, S u = 61.5 kpsi, σ 0 = 110 kpsi, m = 0.4, f = 0.85 After cold working: Eq. (-16), u = m = 0.4 y Ans. Shigley s MED, 10 th edition Chapter Solutions, Page 8/

9 Eq. (-14), A A i 1 W Eq. (-17), A0 εi = ln = ln1.5 = 0. < εu A m Eq. (-18), ( ) 0.4 Eq. (-19), (b) Before: i S y = σ 0ε i = = 76.7 kpsi Ans. 174% increase Ans. Su 61.5 S u = = = 76.9 kpsi Ans. 5% increase Ans. 1 W Su S = y 8 = After: S u 76.9 = = 1.00 S 76.7 Lost most of its ductility. -11 W = 0.0, (a) Before cold working: 04-T4 aluminum alloy. Table A-, S y = 4.0 kpsi, S u = 64.8 kpsi, σ 0 = 100 kpsi, m = 0.15, f = 0.18 After cold working: Eq. (-16), u = m = 0.15 A0 1 1 Eq. (-14), 1.5 A = i 1 W = = A0 Eq. (-17), εi = ln = ln1.5 = 0. > ε f Material fractures. Ans. Ai -1 For H B = 75, Eq. (-1), S u =.4(75) = 95 MPa Ans. -1 Gray cast iron, H B = 00. Eq. (-), S u = 0.(00) 1.5 =.5 kpsi Ans. From Table A-4, this is probably ASTM No. 0 Gray cast iron Ans. -14 Eq. (-1), 0.5H B = 100 H B = 00 Ans. y Ans. Shigley s MED, 10 th edition Chapter Solutions, Page 9/

10 -15 For the data given, converting H B to S u using Eq. (-1) H B S u (kpsi) S u (kpsi) ΣS u = 117 ΣS u = 177 Eq. (1-6) S u Su 117 = = = kpsi Ans. N 10 Eq. (1-7), 10 Su NSu ( 117. i= ) ss = = = 1.7 kpsi Ans. u N For the data given, converting H B to S u using Eq. (-) H B S u (kpsi) S u (kpsi) ΣS u = ΣS u = Shigley s MED, 10 th edition Chapter Solutions, Page 10/

11 Eq. (1-6) S u Su = = = 41.4 kpsi Ans. N 10 Eq. (1-7), 10 Su NSu ( 41.4 i= ) ss = = = 1.0 Ans. u N (a) Eq. (-9) ur 45.6 = (0) 4.7 in lbf / in Ans. (b) A 0 = π(0.50 )/4 = in P L A (A 0 / A) 1 σ = P/A From the figures on the next page, 5 1 ut Ai = (4 000)( ) ( ) i= ( ) ( ) ( ) ( ) ( ) in lbf/in. Ans Shigley s MED, 10 th edition Chapter Solutions, Page 11/

12 Shigley s MED, 10 th edition Chapter Solutions, Page 1/

13 -18, -19 These problems are for student research. No standard solutions are provided. -0 Appropriate tables: Young s modulus and Density (Table A-5)100 HR and CD (Table A- 0), 1040 and 4140 (Table A-1), Aluminum (Table A-4), Titanium (Table A-4c) Appropriate equations: For diameter, F F 4F σ = = = S y d = A d π S ( π / 4) Weight/length = ρa, Cost/length = $/in = ($/lbf) Weight/length, Deflection/length = δ /L = F/(AE) With F = 100 kips = 100(10 ) lbf, y Material Young's Modulus Density Yield Strength Cost/lbf Diameter Weight/ length Cost/ length Deflection/ length units Mpsi lbf/in kpsi $/lbf in lbf/in $/in in/in 100 HR E CD E E E-0 Al E-0 Ti $ E-0 The selected materials with minimum values are shaded in the table above. Ans. -1 First, try to find the broad category of material (such as in Table A-5). Visual, magnetic, and scratch tests are fast and inexpensive, so should all be done. Results from these three would favor steel, cast iron, or maybe a less common ferrous material. The expectation would likely be hot-rolled steel. If it is desired to confirm this, either a weight or bending test could be done to check density or modulus of elasticity. The weight test is faster. From the measured weight of 7.95 lbf, the unit weight is determined to be W 7.95 lbf w = = = 0.81 lbf/in Al [ π (1 in) / 4](6 in) which agrees well with the unit weight of 0.8 lbf/in reported in Table A-5 for carbon steel. Nickel steel and stainless steel have similar unit weights, but surface finish and darker coloring do not favor their selection. To select a likely specification from Table A-0, perform a Brinell hardness test, then use Eq. (-1) to estimate an ultimate strength Shigley s MED, 10 th edition Chapter Solutions, Page 1/

14 of Su = 0.5H B = 0.5(00) = 100 kpsi. Assuming the material is hot-rolled due to the rough surface finish, appropriate choices from Table A-0 would be one of the higher carbon steels, such as hot-rolled AISI 1050, 1060, or Ans. - First, try to find the broad category of material (such as in Table A-5). Visual, magnetic, and scratch tests are fast and inexpensive, so should all be done. Results from these three favor a softer, non-ferrous material like aluminum. If it is desired to confirm this, either a weight or bending test could be done to check density or modulus of elasticity. The weight test is faster. From the measured weight of.90 lbf, the unit weight is determined to be W.9 lbf w = 0.10 lbf/in Al = [ π (1 in) / 4](6 in) = which agrees reasonably well with the unit weight of lbf/in reported in Table A-5 for aluminum. No other materials come close to this unit weight, so the material is likely aluminum. Ans. - First, try to find the broad category of material (such as in Table A-5). Visual, magnetic, and scratch tests are fast and inexpensive, so should all be done. Results from these three favor a softer, non-ferrous copper-based material such as copper, brass, or bronze. To further distinguish the material, either a weight or bending test could be done to check density or modulus of elasticity. The weight test is faster. From the measured weight of 9 lbf, the unit weight is determined to be W 9.0 lbf w = = = 0.18 lbf/in Al [ π (1 in) / 4](6 in) which agrees reasonably well with the unit weight of 0. lbf/in reported in Table A-5 for copper. Brass is not far off (0.09 lbf/in ), so the deflection test could be used to gain additional insight. From the measured deflection and utilizing the deflection equation for an end-loaded cantilever beam from Table A-9, Young s modulus is determined to be ( ) Fl E = 17.7 Mpsi Iy = (1) 64 (17 / ) = 4 ( π ) which agrees better with the modulus for copper (17. Mpsi) than with brass (15.4 Mpsi). The conclusion is that the material is likely copper. Ans. -4 and -5 These problems are for student research. No standard solutions are provided. -6 For strength, σ = F/A = S A = F/S Shigley s MED, 10 th edition Chapter Solutions, Page 14/

15 For mass, m = Alρ = (F/S) lρ Thus, f (M ) = ρ /S, and maximize S/ρ (β = 1) In Fig. (-19), draw lines parallel to S/ρ The higher strength aluminum alloys have the greatest potential, as determined by comparing each material s bubble to the S/ρ guidelines. Ans. -7 For stiffness, k = AE/l A = kl/e For mass, m = Alρ = (kl/e) lρ =kl ρ /E Thus, f (M) = ρ /E, and maximize E/ρ (β = 1) In Fig. (-16), draw lines parallel to E/ρ Shigley s MED, 10 th edition Chapter Solutions, Page 15/

16 From the list of materials given, tungsten carbide (WC) is best, closely followed by aluminum alloys. They are close enough that other factors, like cost or availability, would likely dictate the best choice. Polycarbonate polymer is clearly not a good choice compared to the other candidate materials. Ans. -8 For strength, σ = Fl/Z = S (1) where Fl is the bending moment and Z is the section modulus [see Eq. (-6b), p. 104 ]. The section modulus is strictly a function of the dimensions of the cross section and has the units in (ips) or m (SI). Thus, for a given cross section, Z =C (A) /, where C is a number. For example, for a circular cross section, C = ( ) 1 4 π. Then, for strength, Eq. (1) is Fl CA / Fl = S A = CS / () Shigley s MED, 10 th edition Chapter Solutions, Page 16/

17 For mass, / / Fl F 5/ ρ ρ / m = Alρ = l = l CS C S Thus, f (M) = ρ /S /, and maximize S / /ρ (β = /) In Fig. (-19), draw lines parallel to S / /ρ From the list of materials given, a higher strength aluminum alloy has the greatest potential, followed closely by high carbon heat-treated steel. Tungsten carbide is clearly not a good choice compared to the other candidate materials..ans. -9 Eq. (-6), p. 77, applies to a circular cross section. However, for any cross section shape it can be shown that I = CA, where C is a constant. For example, consider a rectangular section of height h and width b, where for a given scaled shape, h = cb, where c is a constant. The moment of inertia is I = bh /1, and the area is A = bh. Then I = h(bh )/1 = cb (bh )/1 = (c/1)(bh) = CA, where C = c/1 (a constant). Thus, Eq. (-7) becomes Shigley s MED, 10 th edition Chapter Solutions, Page 17/

18 kl A = CE and Eq. (-9) becomes Thus, minimize ( ) 1/ 1/ k 5/ ρ ρ 1/ m = Al = l C E ρ f M =, or maximize M 1/ E 1/ E =. From Fig. (-16) ρ From the list of materials given, aluminum alloys are clearly the best followed by steels and tungsten carbide. Polycarbonate polymer is not a good choice compared to the other candidate materials. Ans. -0 For stiffness, k = AE/l A = kl/e For mass, m = Alρ = (kl/e) lρ =kl ρ /E So, f (M) = ρ /E, and maximize E/ρ. Thus, β = 1. Ans. -1 For strength, σ = F/A = S A = F/S Shigley s MED, 10 th edition Chapter Solutions, Page 18/

19 For mass, m = Alρ = (F/S) lρ So, f (M ) = ρ /S, and maximize S/ρ. Thus, β = 1. Ans. - Eq. (-6), p. 77, applies to a circular cross section. However, for any cross section shape it can be shown that I = CA, where C is a constant. For the circular cross section (see p.77), C = (4π) 1. Another example, consider a rectangular section of height h and width b, where for a given scaled shape, h = cb, where c is a constant. The moment of inertia is I = bh /1, and the area is A = bh. Then I = h(bh )/1 = cb (bh )/1 = (c/1)(bh) = CA, where C = c/1, a constant. Thus, Eq. (-7) becomes kl A = CE and Eq. (-9) becomes 1/ 1/ k 5/ ρ ρ 1/ m = Al = l C E 1/ ρ E So, minimize f ( M ) =, or maximize M =. Thus, β = 1/. Ans. 1/ E ρ - For strength, σ = Fl/Z = S (1) where Fl is the bending moment and Z is the section modulus [see Eq. (-6b), p. 104 ]. The section modulus is strictly a function of the dimensions of the cross section and has the units in (ips) or m (SI). The area of the cross section has the units in or m. Thus, for a given cross section, Z =C (A) /, where C is a number. For example, for a circular cross section, Z = πd /()and the area is A = πd /4. This leads to C = ( 4 π ) 1. So, with Z =C (A) /, for strength, Eq. (1) is Fl CA / Fl = S A = CS / () For mass, / / Fl F 5/ ρ ρ / m = Alρ = l = l CS C S So, f (M) = ρ /S /, and maximize S / /ρ. Thus, β = /. Ans. Shigley s MED, 10 th edition Chapter Solutions, Page 19/

20 -4 For stiffness, k=ae/l, or, A = kl/e. Thus, m = ρal =ρ (kl/e )l = kl ρ /E. Then, M = E /ρ and β = 1. From Fig. -16, lines parallel to E /ρ for ductile materials include steel, titanium, molybdenum, aluminum alloys, and composites. For strength, S = F/A, or, A = F/S. Thus, m = ρal =ρ F/Sl = Fl ρ /S. Then, M = S/ρ and β = 1. From Fig. -19, lines parallel to S/ρ give for ductile materials, steel, aluminum alloys, nickel alloys, titanium, and composites. Common to both stiffness and strength are steel, titanium, aluminum alloys, and composites. Ans. -5 See Prob. 1-1 solution for x = 1.9 kcycles and s x = 0. kcycles. Also, in that solution it is observed that the number of instances less than 115 kcycles predicted by the normal distribution is 7; whereas, the data indicates the number to be 1. From Eq. (1-4), the probability density function (PDF), with µ = x and ˆ σ = sx, is 1 1 x x 1 1 x 1.9 f ( x) = exp = exp s sx x π π (1) The discrete PDF is given by f /(Nw), where N = 69 and w = 10 kcycles. From the Eq. (1) and the data of Prob. 1-1, the following plots are obtained. Shigley s MED, 10 th edition Chapter Solutions, Page 0/

21 Range midpoint (kcycles) Observed PDF Normal PDF Frequency x f f /(Nw) f (x) Plots of the PDF s are shown below Probability Density Normal Distribution Histogram L (kcycles) Shigley s MED, 10 th edition Chapter Solutions, Page 1/

22 It can be seen that the data is not perfectly normal and is skewed to the left indicating that the number of instances below 115 kcycles for the data (1) would be higher than the hypothetical normal distribution (7). Shigley s MED, 10 th edition Chapter Solutions, Page /

Stress-Strain Behavior

Stress-Strain Behavior Stress-Strain Behavior 6.3 A specimen of aluminum having a rectangular cross section 10 mm 1.7 mm (0.4 in. 0.5 in.) is pulled in tension with 35,500 N (8000 lb f ) force, producing only elastic deformation.

More information

N = N A Pb A Pb. = ln N Q v kt. = kt ln v N

N = N A Pb A Pb. = ln N Q v kt. = kt ln v N 5. Calculate the energy for vacancy formation in silver, given that the equilibrium number of vacancies at 800 C (1073 K) is 3.6 10 3 m 3. The atomic weight and density (at 800 C) for silver are, respectively,

More information

CHAPTER 6 MECHANICAL PROPERTIES OF METALS PROBLEM SOLUTIONS

CHAPTER 6 MECHANICAL PROPERTIES OF METALS PROBLEM SOLUTIONS CHAPTER 6 MECHANICAL PROPERTIES OF METALS PROBLEM SOLUTIONS Concepts of Stress and Strain 6.1 Using mechanics of materials principles (i.e., equations of mechanical equilibrium applied to a free-body diagram),

More information

MECE 3321 MECHANICS OF SOLIDS CHAPTER 3

MECE 3321 MECHANICS OF SOLIDS CHAPTER 3 MECE 3321 MECHANICS OF SOLIDS CHAPTER 3 Samantha Ramirez TENSION AND COMPRESSION TESTS Tension and compression tests are used primarily to determine the relationship between σ avg and ε avg in any material.

More information

Introduction to Engineering Materials ENGR2000. Dr. Coates

Introduction to Engineering Materials ENGR2000. Dr. Coates Introduction to Engineering Materials ENGR2 Chapter 6: Mechanical Properties of Metals Dr. Coates 6.2 Concepts of Stress and Strain tension compression shear torsion Tension Tests The specimen is deformed

More information

Chapter (a) (b) f/(n x) = f/(69 10) = f/690

Chapter (a) (b) f/(n x) = f/(69 10) = f/690 Chapter -1 (a) 1 1 8 6 4 6 7 8 9 1 11 1 13 14 15 16 17 18 19 1 (b) f/(n x) = f/(69 1) = f/69 x f fx fx f/(n x) 6 1 7.9 7 1 7 49.15 8 3 4 19.43 9 5 45 4 5.7 1 8 8 8.116 11 1 13 145.174 1 6 7 86 4.87 13

More information

4.MECHANICAL PROPERTIES OF MATERIALS

4.MECHANICAL PROPERTIES OF MATERIALS 4.MECHANICAL PROPERTIES OF MATERIALS The diagram representing the relation between stress and strain in a given material is an important characteristic of the material. To obtain the stress-strain diagram

More information

Appendix. A 1 Properties of areas.* *Symbols used are: A = area I = moment of inertia S = Section modulus

Appendix. A 1 Properties of areas.* *Symbols used are: A = area I = moment of inertia S = Section modulus Appendix A 1 Properties of areas.* *Symbols used are: A = area I = moment of inertia S = Section modulus r = radius of gyration = I/A J = polar moment of inertia Z p = polar section modulus Circle R D

More information

ME 243. Mechanics of Solids

ME 243. Mechanics of Solids ME 243 Mechanics of Solids Lecture 2: Stress and Strain Ahmad Shahedi Shakil Lecturer, Dept. of Mechanical Engg, BUET E-mail: sshakil@me.buet.ac.bd, shakil6791@gmail.com Website: teacher.buet.ac.bd/sshakil

More information

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour

Outline. Tensile-Test Specimen and Machine. Stress-Strain Curve. Review of Mechanical Properties. Mechanical Behaviour Tensile-Test Specimen and Machine Review of Mechanical Properties Outline Tensile test True stress - true strain (flow curve) mechanical properties: - Resilience - Ductility - Toughness - Hardness A standard

More information

STANDARD SAMPLE. Reduced section " Diameter. Diameter. 2" Gauge length. Radius

STANDARD SAMPLE. Reduced section  Diameter. Diameter. 2 Gauge length. Radius MATERIAL PROPERTIES TENSILE MEASUREMENT F l l 0 A 0 F STANDARD SAMPLE Reduced section 2 " 1 4 0.505" Diameter 3 4 " Diameter 2" Gauge length 3 8 " Radius TYPICAL APPARATUS Load cell Extensometer Specimen

More information

6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa ( psi) and

6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa ( psi) and 6.4 A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa (15.5 10 6 psi) and an original diameter of 3.8 mm (0.15 in.) will experience only elastic deformation when a tensile

More information

Tensile stress strain curves for different materials. Shows in figure below

Tensile stress strain curves for different materials. Shows in figure below Tensile stress strain curves for different materials. Shows in figure below Furthermore, the modulus of elasticity of several materials effected by increasing temperature, as is shown in Figure Asst. Lecturer

More information

6.37 Determine the modulus of resilience for each of the following alloys:

6.37 Determine the modulus of resilience for each of the following alloys: 6.37 Determine the modulus of resilience for each of the following alloys: Yield Strength Material MPa psi Steel alloy 550 80,000 Brass alloy 350 50,750 Aluminum alloy 50 36,50 Titanium alloy 800 116,000

More information

ME311 Machine Design

ME311 Machine Design ME311 Machine Design Lecture : Materials; Stress & Strain; Power Transmission W Dornfeld 13Sep018 airfield University School of Engineering Stress-Strain Curve for Ductile Material Ultimate Tensile racture

More information

CHAPTER 7 MECHANICAL PROPERTIES PROBLEM SOLUTIONS

CHAPTER 7 MECHANICAL PROPERTIES PROBLEM SOLUTIONS Excerpts from this work may be reproduced by instructors for distribution on a not-for-profit basis for testing or instructional purposes only to students enrolled in courses for which the textbook has

More information

Bending Load & Calibration Module

Bending Load & Calibration Module Bending Load & Calibration Module Objectives After completing this module, students shall be able to: 1) Conduct laboratory work to validate beam bending stress equations. 2) Develop an understanding of

More information

Chapter (a) (b) f/(n x) = f/(69 10) = f/690

Chapter (a) (b) f/(n x) = f/(69 10) = f/690 Chapter -1 (a) 1 10 8 6 4 0 60 70 80 90 100 110 10 130 140 150 160 170 180 190 00 10 (b) f/(n x) = f/(69 10) = f/690 x f fx fx f/(n x) 60 10 700 0.009 70 1 70 4900 0.0015 80 3 40 19 00 0.0043 90 5 450

More information

ME 207 Material Science I

ME 207 Material Science I ME 207 Material Science I Chapter 3 Properties in Tension and Compression Dr. İbrahim H. Yılmaz http://web.adanabtu.edu.tr/iyilmaz Automotive Engineering Adana Science and Technology University Introduction

More information

High Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there?

High Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there? High Tech High Top Hat Technicians An Introduction to Solid Mechanics Or Is that supposed to bend there? Why don't we fall through the floor? The power of any Spring is in the same proportion with the

More information

Introduction to Structural Member Properties

Introduction to Structural Member Properties Introduction to Structural Member Properties Structural Member Properties Moment of Inertia (I): a mathematical property of a cross-section (measured in inches 4 or in 4 ) that gives important information

More information

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.

NORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric

More information

Mechanical Design in Optical Engineering. For a prismatic bar of length L in tension by axial forces P we have determined:

Mechanical Design in Optical Engineering. For a prismatic bar of length L in tension by axial forces P we have determined: Deformation of Axial Members For a prismatic bar of length L in tension by axial forces P we have determined: σ = P A δ ε = L It is important to recall that the load P must act on the centroid of the cross

More information

Chapter 10 1" 2 4" 1 = MPa mm. 201 = kpsi (0.105) S sy = 0.45(278.7) = kpsi D = = in. C = D d = = 10.

Chapter 10 1 2 4 1 = MPa mm. 201 = kpsi (0.105) S sy = 0.45(278.7) = kpsi D = = in. C = D d = = 10. budynas_sm_ch10.qxd 01/29/2007 18:26 Page 261 Chapter 10 10-1 1" 4" 1" 2 1" 4" 1" 2 10-2 A = Sd m dim( A uscu ) = dim(s) dim(d m ) = kpsi in m dim( A SI ) = dim(s 1 ) dim ( d m ) 1 = MPa mm m A SI = MPa

More information

MECHANICS OF MATERIALS Sample Problem 4.2

MECHANICS OF MATERIALS Sample Problem 4.2 Sample Problem 4. SOLUTON: Based on the cross section geometry, calculate the location of the section centroid and moment of inertia. ya ( + Y Ad ) A A cast-iron machine part is acted upon by a kn-m couple.

More information

Solid Mechanics Homework Answers

Solid Mechanics Homework Answers Name: Date: Solid Mechanics Homework nswers Please show all of your work, including which equations you are using, and circle your final answer. Be sure to include the units in your answers. 1. The yield

More information

Mechanical Properties of Materials

Mechanical Properties of Materials Mechanical Properties of Materials Strains Material Model Stresses Learning objectives Understand the qualitative and quantitative description of mechanical properties of materials. Learn the logic of

More information

Tuesday, February 11, Chapter 3. Load and Stress Analysis. Dr. Mohammad Suliman Abuhaiba, PE

Tuesday, February 11, Chapter 3. Load and Stress Analysis. Dr. Mohammad Suliman Abuhaiba, PE 1 Chapter 3 Load and Stress Analysis 2 Chapter Outline Equilibrium & Free-Body Diagrams Shear Force and Bending Moments in Beams Singularity Functions Stress Cartesian Stress Components Mohr s Circle for

More information

The science of elasticity

The science of elasticity The science of elasticity In 1676 Hooke realized that 1.Every kind of solid changes shape when a mechanical force acts on it. 2.It is this change of shape which enables the solid to supply the reaction

More information

12/8/2009. Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka

12/8/2009. Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Introduction and classes of properties Case studies showing selection of the right material for the job Deformation of material under the action of a

More information

Mechanical properties 1 Elastic behaviour of materials

Mechanical properties 1 Elastic behaviour of materials MME131: Lecture 13 Mechanical properties 1 Elastic behaviour of materials A. K. M. B. Rashid Professor, Department of MME BUET, Dhaka Today s Topics Deformation of material under the action of a mechanical

More information

Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design

Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department

More information

= 50 ksi. The maximum beam deflection Δ max is not = R B. = 30 kips. Notes for Strength of Materials, ET 200

= 50 ksi. The maximum beam deflection Δ max is not = R B. = 30 kips. Notes for Strength of Materials, ET 200 Notes for Strength of Materials, ET 00 Steel Six Easy Steps Steel beam design is about selecting the lightest steel beam that will support the load without exceeding the bending strength or shear strength

More information

STRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains

STRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains STRENGTH OF MATERIALS-I Unit-1 Simple stresses and strains 1. What is the Principle of surveying 2. Define Magnetic, True & Arbitrary Meridians. 3. Mention different types of chains 4. Differentiate between

More information

March 24, Chapter 4. Deflection and Stiffness. Dr. Mohammad Suliman Abuhaiba, PE

March 24, Chapter 4. Deflection and Stiffness. Dr. Mohammad Suliman Abuhaiba, PE Chapter 4 Deflection and Stiffness 1 2 Chapter Outline Spring Rates Tension, Compression, and Torsion Deflection Due to Bending Beam Deflection Methods Beam Deflections by Superposition Strain Energy Castigliano

More information

ME 2570 MECHANICS OF MATERIALS

ME 2570 MECHANICS OF MATERIALS ME 2570 MECHANICS OF MATERIALS Chapter III. Mechanical Properties of Materials 1 Tension and Compression Test The strength of a material depends on its ability to sustain a load without undue deformation

More information

MATERIALS FOR CIVIL AND CONSTRUCTION ENGINEERS

MATERIALS FOR CIVIL AND CONSTRUCTION ENGINEERS MATERIALS FOR CIVIL AND CONSTRUCTION ENGINEERS 3 rd Edition Michael S. Mamlouk Arizona State University John P. Zaniewski West Virginia University Solution Manual FOREWORD This solution manual includes

More information

five Mechanics of Materials 1 ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture

five Mechanics of Materials 1 ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture five mechanics www.carttalk.com of materials Mechanics of Materials 1 Mechanics of Materials MECHANICS MATERIALS

More information

Engineering Science OUTCOME 1 - TUTORIAL 4 COLUMNS

Engineering Science OUTCOME 1 - TUTORIAL 4 COLUMNS Unit 2: Unit code: QCF Level: Credit value: 15 Engineering Science L/601/10 OUTCOME 1 - TUTORIAL COLUMNS 1. Be able to determine the behavioural characteristics of elements of static engineering systems

More information

CIV 207 Winter For practice

CIV 207 Winter For practice CIV 07 Winter 009 Assignment #10 Friday, March 0 th Complete the first three questions. Submit your work to Box #5 on the th floor of the MacDonald building by 1 noon on Tuesday March 31 st. No late submissions

More information

ENGINEERING SCIENCE H1 OUTCOME 1 - TUTORIAL 4 COLUMNS EDEXCEL HNC/D ENGINEERING SCIENCE LEVEL 4 H1 FORMERLY UNIT 21718P

ENGINEERING SCIENCE H1 OUTCOME 1 - TUTORIAL 4 COLUMNS EDEXCEL HNC/D ENGINEERING SCIENCE LEVEL 4 H1 FORMERLY UNIT 21718P ENGINEERING SCIENCE H1 OUTCOME 1 - TUTORIAL COLUMNS EDEXCEL HNC/D ENGINEERING SCIENCE LEVEL H1 FORMERLY UNIT 21718P This material is duplicated in the Mechanical Principles module H2 and those studying

More information

Flexural properties of polymers

Flexural properties of polymers A2 _EN BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS FACULTY OF MECHANICAL ENGINEERING DEPARTMENT OF POLYMER ENGINEERING Flexural properties of polymers BENDING TEST OF CHECK THE VALIDITY OF NOTE ON

More information

MIL-HDBK-5H 1 December 1998

MIL-HDBK-5H 1 December 1998 components are calculated. In some cases, the methods presented are empirical and subject to further refinements. Any further expansion of information on element behavior in MIL-HDBK-5 will emphasize those

More information

Bending Stress. Sign convention. Centroid of an area

Bending Stress. Sign convention. Centroid of an area Bending Stress Sign convention The positive shear force and bending moments are as shown in the figure. Centroid of an area Figure 40: Sign convention followed. If the area can be divided into n parts

More information

[5] Stress and Strain

[5] Stress and Strain [5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law

More information

12/25/ :27 PM. Chapter 14. Spur and Helical Gears. Mohammad Suliman Abuhaiba, Ph.D., PE

12/25/ :27 PM. Chapter 14. Spur and Helical Gears. Mohammad Suliman Abuhaiba, Ph.D., PE Chapter 14 Spur and Helical Gears 1 2 The Lewis Bending Equation Equation to estimate bending stress in gear teeth in which tooth form entered into the formulation: 3 The Lewis Bending Equation Assume

More information

Problem d d d B C E D. 0.8d. Additional lecturebook examples 29 ME 323

Problem d d d B C E D. 0.8d. Additional lecturebook examples 29 ME 323 Problem 9.1 Two beam segments, AC and CD, are connected together at C by a frictionless pin. Segment CD is cantilevered from a rigid support at D, and segment AC has a roller support at A. a) Determine

More information

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering

Mechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering Mechanics Of Solids Suraj kr. Ray (surajjj2445@gmail.com) Department of Civil Engineering 1 Mechanics of Solids is a branch of applied mechanics that deals with the behaviour of solid bodies subjected

More information

Mechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection

Mechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection Mechanics of Materials II Chapter III A review of the fundamental formulation of stress, strain, and deflection Outline Introduction Assumtions and limitations Axial loading Torsion of circular shafts

More information

Solid Mechanics Chapter 1: Tension, Compression and Shear

Solid Mechanics Chapter 1: Tension, Compression and Shear Solid Mechanics Chapter 1: Tension, Compression and Shear Dr. Imran Latif Department of Civil and Environmental Engineering College of Engineering University of Nizwa (UoN) 1 Why do we study Mechanics

More information

BEAM DEFLECTION THE ELASTIC CURVE

BEAM DEFLECTION THE ELASTIC CURVE BEAM DEFLECTION Samantha Ramirez THE ELASTIC CURVE The deflection diagram of the longitudinal axis that passes through the centroid of each cross-sectional area of a beam. Supports that apply a moment

More information

Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study

Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus Case study 2 In field of Physics, it explains how an object deforms under an applied force Real rigid bodies are elastic we can

More information

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A

QUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A DEPARTMENT: CIVIL SUBJECT CODE: CE2201 QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State

More information

UNIT-I STRESS, STRAIN. 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2

UNIT-I STRESS, STRAIN. 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2 UNIT-I STRESS, STRAIN 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2 Young s modulus E= 2 x10 5 N/mm 2 Area1=900mm 2 Area2=400mm 2 Area3=625mm

More information

MECHANICS OF MATERIALS

MECHANICS OF MATERIALS CHATR Stress MCHANICS OF MATRIALS and Strain Axial Loading Stress & Strain: Axial Loading Suitability of a structure or machine may depend on the deformations in the structure as well as the stresses induced

More information

Johns Hopkins University What is Engineering? M. Karweit MATERIALS

Johns Hopkins University What is Engineering? M. Karweit MATERIALS Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: MATERIALS A. Composition

More information

Elastic Properties of Solid Materials. Notes based on those by James Irvine at

Elastic Properties of Solid Materials. Notes based on those by James Irvine at Elastic Properties of Solid Materials Notes based on those by James Irvine at www.antonine-education.co.uk Key Words Density, Elastic, Plastic, Stress, Strain, Young modulus We study how materials behave

More information

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work.

MAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work. It is most beneficial to you to write this mock final exam UNDER EXAM CONDITIONS. This means: Complete the exam in 3 hours. Work on your own. Keep your textbook closed. Attempt every question. After the

More information

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC.

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC. BENDING STRESS The effect of a bending moment applied to a cross-section of a beam is to induce a state of stress across that section. These stresses are known as bending stresses and they act normally

More information

Sub. Code:

Sub. Code: Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. ) The model answer and the answer written by candidate may

More information

Mechanics of Materials Primer

Mechanics of Materials Primer Mechanics of Materials rimer Notation: A = area (net = with holes, bearing = in contact, etc...) b = total width of material at a horizontal section d = diameter of a hole D = symbol for diameter E = modulus

More information

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics Page1 PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [2910601] Introduction, Fundamentals of Statics 1. Differentiate between Scalar and Vector quantity. Write S.I.

More information

Chapter 7. Highlights:

Chapter 7. Highlights: Chapter 7 Highlights: 1. Understand the basic concepts of engineering stress and strain, yield strength, tensile strength, Young's(elastic) modulus, ductility, toughness, resilience, true stress and true

More information

FME461 Engineering Design II

FME461 Engineering Design II FME461 Engineering Design II Dr.Hussein Jama Hussein.jama@uobi.ac.ke Office 414 Lecture: Mon 8am -10am Tutorial Tue 3pm - 5pm 10/1/2013 1 Semester outline Date Week Topics Reference Reading 9 th Sept 1

More information

Chapter 9. Figure for Probs. 9-1 to Given, b = 50 mm, d = 50 mm, h = 5 mm, τ allow = 140 MPa.

Chapter 9. Figure for Probs. 9-1 to Given, b = 50 mm, d = 50 mm, h = 5 mm, τ allow = 140 MPa. Chapter 9 Figure for Probs. 9-1 to 9-4 9-1 Given, b 50 mm, d 50 mm, h 5 mm, ow 140 MPa. F 0.707 hl ow 0.707(5)[(50)](140)(10 ) 49.5 kn Ans. 9- Given, b in, d in, h 5/16 in, ow 5 kpsi. F 0.707 hl ow 0.707(5/16)[()](5).1

More information

MATERIALS. Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle?

MATERIALS. Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? MATERIALS Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: A. Composition

More information

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV UNIT I STRESS, STRAIN DEFORMATION OF SOLIDS PART A (2 MARKS)

More information

2. Determine the deflection at C of the beam given in fig below. Use principal of virtual work. W L/2 B A L C

2. Determine the deflection at C of the beam given in fig below. Use principal of virtual work. W L/2 B A L C CE-1259, Strength of Materials UNIT I STRESS, STRAIN DEFORMATION OF SOLIDS Part -A 1. Define strain energy density. 2. State Maxwell s reciprocal theorem. 3. Define proof resilience. 4. State Castigliano

More information

Name :. Roll No. :... Invigilator s Signature :.. CS/B.TECH (CE-NEW)/SEM-3/CE-301/ SOLID MECHANICS

Name :. Roll No. :... Invigilator s Signature :.. CS/B.TECH (CE-NEW)/SEM-3/CE-301/ SOLID MECHANICS Name :. Roll No. :..... Invigilator s Signature :.. 2011 SOLID MECHANICS Time Allotted : 3 Hours Full Marks : 70 The figures in the margin indicate full marks. Candidates are required to give their answers

More information

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS

QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,

More information

How materials work. Compression Tension Bending Torsion

How materials work. Compression Tension Bending Torsion Materials How materials work Compression Tension Bending Torsion Elemental material atoms: A. Composition a) Nucleus: protons (+), neutrons (0) b) Electrons (-) B. Neutral charge, i.e., # electrons = #

More information

Laboratory 4 Bending Test of Materials

Laboratory 4 Bending Test of Materials Department of Materials and Metallurgical Engineering Bangladesh University of Engineering Technology, Dhaka MME 222 Materials Testing Sessional.50 Credits Laboratory 4 Bending Test of Materials. Objective

More information

Module 5: Theories of Failure

Module 5: Theories of Failure Module 5: Theories of Failure Objectives: The objectives/outcomes of this lecture on Theories of Failure is to enable students for 1. Recognize loading on Structural Members/Machine elements and allowable

More information

ME 323 Examination #2 April 11, 2018

ME 323 Examination #2 April 11, 2018 ME 2 Eamination #2 April, 2 PROBLEM NO. 25 points ma. A thin-walled pressure vessel is fabricated b welding together two, open-ended stainless-steel vessels along a 6 weld line. The welded vessel has an

More information

MEMS Project 2 Assignment. Design of a Shaft to Transmit Torque Between Two Pulleys

MEMS Project 2 Assignment. Design of a Shaft to Transmit Torque Between Two Pulleys MEMS 029 Project 2 Assignment Design of a Shaft to Transmit Torque Between Two Pulleys Date: February 5, 206 Instructor: Dr. Stephen Ludwick Product Definition Shafts are incredibly important in order

More information

ISHIK UNIVERSITY DEPARTMENT OF MECHATRONICS ENGINEERING

ISHIK UNIVERSITY DEPARTMENT OF MECHATRONICS ENGINEERING ISHIK UNIVERSITY DEPARTMENT OF MECHATRONICS ENGINEERING QUESTION BANK FOR THE MECHANICS OF MATERIALS-I 1. A rod 150 cm long and of diameter 2.0 cm is subjected to an axial pull of 20 kn. If the modulus

More information

UNIT III DEFLECTION OF BEAMS 1. What are the methods for finding out the slope and deflection at a section? The important methods used for finding out the slope and deflection at a section in a loaded

More information

2012 MECHANICS OF SOLIDS

2012 MECHANICS OF SOLIDS R10 SET - 1 II B.Tech II Semester, Regular Examinations, April 2012 MECHANICS OF SOLIDS (Com. to ME, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~

More information

9 MECHANICAL PROPERTIES OF SOLIDS

9 MECHANICAL PROPERTIES OF SOLIDS 9 MECHANICAL PROPERTIES OF SOLIDS Deforming force Deforming force is the force which changes the shape or size of a body. Restoring force Restoring force is the internal force developed inside the body

More information

PES Institute of Technology

PES Institute of Technology PES Institute of Technology Bangalore south campus, Bangalore-5460100 Department of Mechanical Engineering Faculty name : Madhu M Date: 29/06/2012 SEM : 3 rd A SEC Subject : MECHANICS OF MATERIALS Subject

More information

ENG1001 Engineering Design 1

ENG1001 Engineering Design 1 ENG1001 Engineering Design 1 Structure & Loads Determine forces that act on structures causing it to deform, bend, and stretch Forces push/pull on objects Structures are loaded by: > Dead loads permanent

More information

ESE TOPICWISE OBJECTIVE SOLVED PAPER I

ESE TOPICWISE OBJECTIVE SOLVED PAPER I C I V I L E N G I N E E R I N G ESE TOPICWISE OBJECTIVE SOLVED PAPER I FROM 1995-018 UPSC Engineering Services Eamination, State Engineering Service Eamination & Public Sector Eamination. Regd. office

More information

Materials: engineering, science, processing and design, 2nd edition Copyright (c)2010 Michael Ashby, Hugh Shercliff, David Cebon.

Materials: engineering, science, processing and design, 2nd edition Copyright (c)2010 Michael Ashby, Hugh Shercliff, David Cebon. Modes of Loading (1) tension (a) (2) compression (b) (3) bending (c) (4) torsion (d) and combinations of them (e) Figure 4.2 1 Standard Solution to Elastic Problems Three common modes of loading: (a) tie

More information

POE Practice Test - Materials

POE Practice Test - Materials Class: Date: POE Practice Test - Materials Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A student weighs 150 lbs and is standing on a beam which spans

More information

2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at A and supported at B by rod (1). What is the axial force in rod (1)?

2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at A and supported at B by rod (1). What is the axial force in rod (1)? IDE 110 S08 Test 1 Name: 1. Determine the internal axial forces in segments (1), (2) and (3). (a) N 1 = kn (b) N 2 = kn (c) N 3 = kn 2. Rigid bar ABC supports a weight of W = 50 kn. Bar ABC is pinned at

More information

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram CHAPTER NINE COLUMNS 4 b. The modified axial strength in compression is reduced to account for accidental eccentricity. The magnitude of axial force evaluated in step (a) is multiplied by 0.80 in case

More information

1 332 Laboratories 1. 2 Computational Exercises 1 FEA of a Cantilever Beam... 1 Experimental Laboratory: Tensile Testing of Materials...

1 332 Laboratories 1. 2 Computational Exercises 1 FEA of a Cantilever Beam... 1 Experimental Laboratory: Tensile Testing of Materials... 1 332 Laboratories Contents 1 332 Laboratories 1 2 Computational Exercises 1 FEA of a Cantilever Beam.......................................... 1 Experimental Laboratory: Tensile Testing of Materials..........................

More information

Danger of Snow in the Sunshine State

Danger of Snow in the Sunshine State Undergraduate Journal of Mathematical Modeling: One + Two Volume 7 2017 Spring 2017 Issue 2 Article 2 Danger of Snow in the Sunshine State Dmitrii Karpenko University of South Florida Advisors: Arcadii

More information

A concrete cylinder having a a diameter of of in. mm and elasticity. Stress and Strain: Stress and Strain: 0.

A concrete cylinder having a a diameter of of in. mm and elasticity. Stress and Strain: Stress and Strain: 0. 2011 earson Education, Inc., Upper Saddle River, NJ. ll rights reserved. This material is protected under all copyright laws as they currently 8 1. 3 1. concrete cylinder having a a diameter of of 6.00

More information

Torsion of Shafts Learning objectives

Torsion of Shafts Learning objectives Torsion of Shafts Shafts are structural members with length significantly greater than the largest cross-sectional dimension used in transmitting torque from one plane to another. Learning objectives Understand

More information

COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 3013 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6

COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 3013 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6 COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 0 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6 TIME SCHEDULE Module Topics Period Moment of forces Support reactions Centre

More information

Failure from static loading

Failure from static loading Failure from static loading Topics Quiz /1/07 Failures from static loading Reading Chapter 5 Homework HW 3 due /1 HW 4 due /8 What is Failure? Failure any change in a machine part which makes it unable

More information

Chapter 4-b Axially Loaded Members

Chapter 4-b Axially Loaded Members CIVL 222 STRENGTH OF MATERIALS Chapter 4-b Axially Loaded Members AXIAL LOADED MEMBERS Today s Objectives: Students will be able to: a) Determine the elastic deformation of axially loaded member b) Apply

More information

,. 'UTIS. . i. Univcnity of Technology, Sydney TO BE RETURNED AT THE END OF EXAMINATION. THIS PAPER MUST NOT BE REMOVED FROM THE EXAM CENTRE.

,. 'UTIS. . i. Univcnity of Technology, Sydney TO BE RETURNED AT THE END OF EXAMINATION. THIS PAPER MUST NOT BE REMOVED FROM THE EXAM CENTRE. ,. 'UTIS. i,i I Univcnity of Technology, Sydney TO BE RETURNED AT THE END OF EXAMINATION. THIS PAPER MUST NOT BE REMOVED FROM THE EXAM CENTRE. SURNAME: FIRST NAME: STUDENT NUMBER: COURSE: Tutor's name:

More information

(1) Brass, an alloy of copper and zinc, consists of 70% by volume of copper and 30% by volume of zinc.

(1) Brass, an alloy of copper and zinc, consists of 70% by volume of copper and 30% by volume of zinc. PhysicsAndMathsTutor.com 1 Q1. (a) Define the density of a material....... (1) (b) Brass, an alloy of copper and zinc, consists of 70% by volume of copper and 30% by volume of zinc. density of copper =

More information

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion Introduction Stress and strain in components subjected to torque T Circular Cross-section shape Material Shaft design Non-circular

More information

CHAPTER 2 Failure/Fracture Criterion

CHAPTER 2 Failure/Fracture Criterion (11) CHAPTER 2 Failure/Fracture Criterion (12) Failure (Yield) Criteria for Ductile Materials under Plane Stress Designer engineer: 1- Analysis of loading (for simple geometry using what you learn here

More information

Mechanics of Structure

Mechanics of Structure S.Y. Diploma : Sem. III [CE/CS/CR/CV] Mechanics of Structure Time: Hrs.] Prelim Question Paper Solution [Marks : 70 Q.1(a) Attempt any SIX of the following. [1] Q.1(a) Define moment of Inertia. State MI

More information

Donald P. Shiley School of Engineering ME 328 Machine Design, Spring 2019 Assignment 1 Review Questions

Donald P. Shiley School of Engineering ME 328 Machine Design, Spring 2019 Assignment 1 Review Questions Donald P. Shiley School of Engineering ME 328 Machine Design, Spring 2019 Assignment 1 Review Questions Name: This is assignment is in workbook format, meaning you may fill in the blanks (you do not need

More information

5. What is the moment of inertia about the x - x axis of the rectangular beam shown?

5. What is the moment of inertia about the x - x axis of the rectangular beam shown? 1 of 5 Continuing Education Course #274 What Every Engineer Should Know About Structures Part D - Bending Strength Of Materials NOTE: The following question was revised on 15 August 2018 1. The moment

More information