New analytical formulation of the De Marchi model for zero height side. weir

Size: px
Start display at page:

Download "New analytical formulation of the De Marchi model for zero height side. weir"

Transcription

1 New analytical formulation of the De Marchi model for zero height side weir Giovanni Michelazzo 1 Abstract One-dimensional modeling is often used to simulate the hydrodynamics of free-surface flows, including spatially-varied flows as encountered along the side weirs. This paper deals with the particular case of a side weir with zero height crest acting on fixed bed and subcritical flow, for which a new analytical model is formulated starting from the De Marchi hypothesis. The proposed model provides an original interpretation of the side weir problem for which the solution, formulated in dimensionless form in terms of average flow and geometrical variables of the side weir and main channel, is the explicit result of the imposed boundary conditions at the upstream and downstream cross-sections. The proposed model appears to be able to analyze a wide range of hydraulic problems similar to the side weir flow, such as lateral diversions, and to solve design and verification problems as first approximation. The analytical model is used to predict experimental data coming from literature as well as from a new set of laboratory data in a very direct way without any need of numerical techniques Subject headings: Channel flow; Hydraulic models; Laboratory tests; One dimensional flow, Weirs Key-words: 1D analytical model; De Marchi hypothesis; Laboratory investigations; Side weir; Zero height crest. 1 PhD, Postdoctoral researcher Department of Civil and Environmental Engineering, University of Florence Via S. Marta 3, Firenze, Italy Phone: giovanni.michelazzo@dicea.unifi.it Corresponding author. 1

2 Introduction to the side weir modeling Side weir flows are frequently modeled by means of numerical techniques relying on onedimensional (1D) approaches. Actually, the flow field in the main channel close to the side weir is more complex, since the lateral outflow induces changes in the flow pattern, velocity distribution and mass transport (Neary and Odgaard 1993; Lee and Holley 2002; May et al. 2003; Rosier 2007). Though several contributions have been developed in order to simulate the flow field into details by means of two-dimensional (2D) and three-dimensional (3D) numerical models (Neary et al. 1999; Vasquez 2005; Li and Zeng 2009; Zhou and Zeng 2009), a strong interest still exists on predicting the main flow features in side weir problems by means of simpler 1D approaches (May et al. 2003), which can be applied straightforwardly to several practical situations frequently found in environmental and river engineering. In fact, the hydraulic design of a side weir is often addressed by means of simplified approaches that are based on the equations of the steady, spatially-varied, one-dimensional flow (Subramanya and Awasthy 1972; Hager 1987; Borghei et al. 1999; Oliveto et al. 2001; Durga Rao and Pillai 2008; Emiroglu et al. 2011). Such scheme can predict the flow variables as averages on the cross-section along the main channel, whereas the variations in the vertical and transverse directions are not reproduced. One-dimensional approaches are theoretically more appropriate for those situations in which the flow develops mainly along a longitudinal direction and the secondary flow structures do not get high importance. The longitudinal dimension should be larger than transverse and vertical ones in order to have a good reproduction by 1D-models and, even if it is not possible to define a precise and generally valid range of the geometrical dimensions for which a 1D model may be acceptable since the answer depends on the case and on the goal of the study, it 2

3 49 is usually accepted the ratio between the flow depth and the channel width to approximately 50 get values around Y/B If the prediction of the flow only in its longitudinal development is considered to provide a sufficiently detailed description of the hydrodynamics, then the 1Dmodels may be applied, with the restriction that transverse effects are neglected. The choice of a 1D-scheme provides benefits in terms of easy implementation and possibility to formulate general solutions of the side weir problem. One-dimensional models can be formulated in order to achieve analytical solutions, that offer expeditious tools to predict the longitudinal rate of change of the flow depth and the water discharge in the main channel along a side weir. Within this context, an important contribution to the analytical modeling was given by De Marchi (1934), who developed an equation to predict the longitudinal profile of flow depth under the assumption that the energy per unit weight of the flow remains constant along the side weir. Several past and more recent studies about side weirs rely on the De Marchi assumption (Singh et al. 1994; Borghei et al. 1999; Paris et al. 2012; Namaee et al. 2013), which can reasonably hold in the case of subcritical flows and mild slope of the channel. Recently, some authors developed the De Marchi solution in order to take into account additional effects, such as the variations along the side weir of the specific energy, discharge coefficient and Coriolis coefficient (Venutelli 2008), or different shapes of the main channel, such as trapezoidal (Cheong 1991), triangular (Vatankhah 2012a), circular (Vatankhah 2012b) and U-shaped (Vatankhah 2013) cross-sections. All these studies highlight the scientific interest in proposing analytical or semi-analytical approaches to the side weir problem as useful and handy tools to predict the diverted discharge through existing or designed side weirs. The particular case of a side weir with zero height crest (i.e., with the weir crest at the same elevation of the main channel bottom) has been less addressed, despite it has interesting 3

4 similarities with other free-surface problems, such as branch channels in river bifurcation, lateral intakes and levee breaches. A new analytical formulation of the De Marchi model is developed in this study for steady flow and fixed bed conditions which allows to evaluate flow and geometrical features of a zero height side weir related to the main channel characteristics as functions of the flow conditions imposed at the upstream and downstream sections. The proposed formulation is used to simulate the main flow features of experimental data from the existing literature and from the new set of laboratory investigations performed in the framework of this study New analytical formulation of the De Marchi model A side weir of zero height crest with rectangular shape is considered along a free-surface channel with a rectangular cross-section of width B, fixed bottom and mild slope (see Fig. 1) Fig. 1. Side weir problem: plan view (a); longitudinal section (b); cross section (c) The overflow through the side weir length L s is considered not to be influenced by backwater effects from the tailwater and the De Marchi is assumed, i.e. the total head of the flow remains constant along the side weir. Assuming a negligible variation of the bed elevation between the cross-sections 1 and 2, also the specific energy head can be considered to be constant along the side weir, so that the mass and energy conservation provides the following system: 96 dq(x) dx q C 2g Y(x) s de(x) dx d 0 3/ 2 (1) 4

5 where E [m] is the specific energy head in the main channel; Y [m] is the flow depth; Q [m 3 /s] is the water discharge in the main channel; q s [m 2 /s] is the discharge diverted through the side weir per unit length; x [m] is the longitudinal axis starting at the beginning of the side weir and directed as the main flow direction (see Fig. 1); g is the gravity acceleration [m/s 2 ]; C d [-] is a discharge coefficient assumed to be constant along the side weir. The traditional solution provided by De Marchi (1934) states: 103 Cd x B E Y 1 E Y 2 3sin Y E (2) 104 where is a dimensionless flow function and C is an integration constant determined from the boundary conditions. The new formulation of the De Marchi model is proposed by means of a rearrangement of the equation of conservation of mass, the equation of balance of energy and the De Marchi equation (2) in order to express the main variables of the system as characteristic dimensionless ratios between the side weir and the main channel features depicted in Fig. 1: - Flow depth ratio r Y = Y d / Y u, where Y u and Y d are the flow depths at the upstream and downstream section of the side weir, respectively - Discharge ratio r Q = Q s / Q u, where Q s and Q u are the water discharges diverted through the side weir and incoming from upstream, respectively - Length ratio r L = L s / B These dimensionless ratios are here expressed as functions of the flow conditions achieved at the upstream and downstream cross-sections of the side weir (sections 1 and 2, respectively, in Fig. 1) in terms of the Froude number Fr. 5

6 120 In particular, the balance of the specific energy head E, together with the assumption that 121 the Coriolis coefficients at the upstream and downstream cross-sections can be taken equal 122 to unity as a first approximation, gives the flow depth ratio r Y : 123 E E r u d Y Y Y d u 2 2 Fr Fr 2 u 2 d (3) The continuity principle is used to get the discharge ratio r Q : Q Fr Q Q Q r 1 r s d 3/ 2 s u d Q Y Qu Fru (4) 126 The length ratio r L is finally determined from the system 2: 127 r L L B s d u C d (5) 128 where the dimensionless flow function is expressed in terms of Fr: sin Fr 2 (6) Moreover, the ratio between the average flow velocities at the downstream and upstream sections is directly deduced: 132 r U U U d u 1 rq r Y (7) The characteristic ratios are solved once the flow conditions at the upstream and downstream sections are provided. The side weir problem is then described as a combination 135 of the state variables Fr u and Fr d that define a plane, here called, in which the behavior of the flow along a generic side weir is represented as referred to different conditions (see Fig. 2): a) The channel has a mild slope, the flow is subcritical everywhere, the flow depth profile increases downstream and Fr decreases downstream; 6

7 b) The channel has a steep slope, the flow is supercritical everywhere, the flow depth profile decreases downstream and Fr increases downstream; c) The incoming flow is supercritical, the downstream flow is subcritical and a hydraulic jump occurs within the side weir length. In this case, it is not possible to state a priori whether the downstream flow depth is greater or lower than the upstream one Fig. 2. Side weir situation in the Froude graph: a) subcritical; b) supercritical; c) hydraulic jump The dashed areas in Fig. 2 identify flow combinations which are not physically possible: a subcritical approaching flow remains subcritical along the side weir, whereas a supercritical approaching flow gets greater Fr downstream, except when a downstream control requires a depth larger than the critical one Y cr. An analytical demonstration of such behavior is provided by Montes (1998) for a main channel with a rectangular section: dfr(x) Fr(x) dq(x) 2 Fr (x) 2 dx 2Q(x) dx 1 Fr (x) (8) The dimensionless solution of the side weir problem expressed by Eqs. (3) to (7) is computed for every admissible combination of the Froude numbers in the considered case of a subcritical flow (area a in Fig. 2). Any considered couple (Fr u ; Fr d ) can be obtained as a combination of different values of the imposed independent variables, which are: main channel geometry, bed roughness, bed slope, incoming discharge, side weir length, and boundary conditions, e.g. downstream rating curve. Model results are shown by Fig. 3 in terms of contours of the dimensionless ratios in the Froude graph. 7

8 Fig. 3. Dimensionless ratios from the analytical model: a) r Y contours; b) r Q contours; c) r L contours; d) r U contours. The 45 line defines the condition Fr u = Fr d, which occurs when no lateral outflow takes place in the channel (Q s = 0). In such situation the flow depth and the discharge remain unchanged from upstream to downstream (r Y = 1, r Q = 0, r L = 0, r U = 1), since the side weir flow does not exist. On the other hand, the presence of a side weir makes an outflow possible in the region where Fr u > Fr d : the main channel flow is spatially varied in terms of flow depth increasing downstream (r Y > 1), flow discharge and velocity decreasing (r Q > 0, r U < 1) along the side weir length (r L > 0). This trend develops for increasing Fr u and decreasing Fr d and the influence of the downstream condition on the side weir flow is particularly evident from the contours of r Q in Fig. 3b, in which a significant increase of the diverted discharge is obtained by imposing a boundary condition associated with lower Fr d rather than greater Fr u. An increase of Fr u, which may be related to a greater acceleration of the upstream flow due to a longer side weir, does not make a so efficient increase of the diverted discharge as a decrease of Fr d does, at least if the flow is required to be subcritical. A limiting case is recognized when the critical state occurs in the upstream section (Fr u = 1) and no flow takes place downstream (r U = 0 and Fr d = 0), which is depicted in the upper left corner of the graphs of Fig. 3. In that situation, the characteristic ratios regarding flow depth, water discharge and side weir length achieve their maximum values: r Ymax = 1.5 is a constant for a rectangular cross-section, r Qmax = 1 and r Lmax tends to a value which is on the order of the channel width and which depends on the discharge coefficient C d. The curves of Fig. 3c were calculated by setting the classical value for broad-crested weirs C d = and the maximum length ratio resulted r Lmax

9 188 The length ratio r L is directly determined by the De Marchi model and it depends on the 189 -function in addition to the coefficient C d. The variation of with Fr is shown in Fig. 4: the 190 function gets a minimum min 0.43 at the critical state and two conjugated roots of are 191 detected for subcritical (Fr = 0) and supercritical (Fr 2.05) flow. The maximum variation of 192 the -function in the subcritical range is therefore given for a critical state at the upstream 193 section and no flow at the downstream section, as already discussed with reference to Fig. 3c Fig. 4. Trend of -function in a subcritical and supercritical flow In order to analyze the influence of the discharge coefficient on the length ratio, some of the existing formulations for C d are compared in Fig. 5. The discharge coefficient is then calculated for each grid point of the Froude graph and the effect of each considered formulation of C d on r L is shown by graphs of Fig Fig. 5. Variation of C d with Fr u according to different formulations The choice of C d affects the values of r L, but it does not influence the general behavior of the solution, as r L is still increasing for greater Fr u and smaller Fr d and its maximum value is always in the range [1 4]. In particular, formulations proposed by Hager (1987), in Fig. 6d, and by Borghei et al. (1999), in Fig. 6f, show similar results of the solution, which are also obtained by imposing a constant C d, as in Fig. 6a. On the other hand, the formulation by Ranga Raju et al. (1979), in Fig. 6c, gives values comparable with Singh et al. (1994), in Fig. 6e, whereas the formulation by Subramanya and Awasthy (1972), in Fig. 6b, provides the most different results in terms of values and trend of the r L -function

10 Fig. 6. Comparison of r L contours according to different formulations of C d : a) C d = 0.385; b) Subramanya and Awasthy (1972); c) Ranga Raju et al. (1979); d) Hager (1987); e) Singh et al. (1994); f) Borghei et al. (1999) Laboratory investigations on a zero height side weir New laboratory experiments were carried out at the hydraulic laboratory of Civil and Environmental Engineering of the University of Florence in a 5.10 m long, 0.43 m wide and 0.30 m deep, glass-walled, water-recirculating, tilting flume with a rectangular cross-section (see the experimental set-up in Fig. 7). The flume was subdivided longitudinally into two channels separated by a vertical 0.30 m high glass wall and it was tilted with an inclination S 0 = 0.1 %. The main channel, where the incoming water discharge Q u was put in, was 0.30 m wide and 0.16 m deep, being its bottom raised in order to avoid backwater effects from the tailwater toward the main flow. The lateral channel, 0.12 m wide and 0.30 m deep, allowed to evacuate the discharge Q s diverted by a side weir placed at about 2 m from the flume entrance section on the left side of the main channel. The side weir crest was at the same elevation of the main channel bottom and its length L s could be set up to about 0.5 m: the main and the lateral channels were separated, so that the water could flow in the lateral channel only through the side weir. At the downstream end of the main channel a vertical sluice gate was set to regulate the downstream boundary condition in terms of the flow depth and rate, while the lateral channel ended over the storage basin. A fixed roughness composed by granular gravel with a median diameter D 50 = 6.8 mm was stuck down to the bottom of the main channel in order to provide a realistic resistance to the flow (dimensionless Chézy coefficient in the order of C h 10). 10

11 D-. Fig. 7. Experimental set-up in the tilting flume: a) plan view; b) longitudinal section A The same constant inflow discharge Q u of about 10 l/s was set during the investigations, whereas L s was changed according to ten different values ranging from 3 to 47 cm. Moreover, two different downstream boundary conditions were imposed by choosing two different configurations for the sluice gate. The two configurations,, were set by choosing the opening extent of the vertical sluice gate: in particular, discharge, a larger flow depth took place in the downstream reach of the flume. Finally, no sediment was put into the flume. Table 1 provides a synthesis of the experimental conditions of the runs. The goal of the experimental activity was not to scale a singular case of study, but it was to investigate a process. The experimental set-up allowed to reproduce a flow that was characterized by typical values of the Reynolds number of about Re = 10 5, that, for a relative roughness R = 10-1 (where R is the ratio between the absolute roughness of the channel bed and the hydraulic radius), is referred to a fully turbulent flow (rough flow regime). Therefore, it was considered that the main turbulent flow structures could be reasonably reproduced Measurements of the water surface and the water discharge were taken. The water surface was measured along the centerline (x-axis in Fig. 7) of the main channel every 1 cm of 259 longitudinal distance by means of ultrasonic sensors having a precision of 1 mm and the local flow depth Y referred to the fixed bottom of the main channel was then calculated. The data regarding the flow depth at the upstream and downstream sections of the side weir are 11

12 reported in this paper, whereas further experimental results regarding the observed flow field will be presented in a forthcoming paper. The inflow discharge Q u was recirculated from the storage basin and it was measured by an 265 electromagnetic flow meter installed at the inflow pipe with an accuracy of 10-4 m 3 /s The diverted discharge Q s through the side weir was calculated by using a rating curve previously calibrated at the downstream zone of the lateral channel and with the water level measured at the same location by an ultrasonic sensor. The water discharge flowing in the main channel downstream the side weir Q d was calculated as the difference between the 270 inflow and the diverted discharge (Q d = Q u Q s ) and, as a further control, by using another calibrated rating curve at the downstream zone of the main channel. The main experimental results in terms of the flow depth and the water discharge at the upstream and downstream sections of the side weir are reported in Table Table 1. Summary of conditions and results for the performed tests (for each test: main channel width B = 0.3 m, side weir with zero height crest) Performances of the proposed model The proposed model is now tested with the experimental data that have been found in the analyzed literature and that have been collected within the present work. Moreover, a comparison with the classical models is provided, in order to highlight the novelty of the proposed approach Comparison between the experimental data and the proposed model 12

13 The proposed analytical model is applied to the new laboratory investigations regarding side weirs with a zero height crest presented in the previous Section. Only the runs related to the subcritical flow conditions are taken into account in order to satisfy the model assumptions and such verification is made by checking the flow depth profile to be increasing along the entire length side weir: as a consequence, tests B7 to B13 and C17 to C19 are selected, for which the flow conditions ranged within Fr u = [ ] and Fr d = [ ]. Other tests, as B14 to B16 and C20, are not selected, since they showed a decreasing flow depth profile at the beginning of the side weir, that might be related to the occurrence of a modest submerged hydraulic jump similar to the condition in Fig. 2c, with the particular case of subcritical approaching flow and critical state at the upstream section. Moreover, additional data sets were searched in the literature regarding side weirs. Unfortunately, very few experimental data regarding the case of side weir with a zero height crest and conditions of a subcritical flow have been found: data from Awasthy (1970) and Subramanya and Awasthy (1972) were the only data that considered the aforementioned conditions, so that they could be used in the present work, whereas other data did not satisfy the conditions (as data by Hager, 1981). Therefore, data from Awasthy (1970), that are included in Subramanya and Awasthy (1972), are here used to test the reliability of the proposed model for a zero height side weir and subcritical flow conditions, which ranged within Fr u = [ ], Fr d = [ ] 305 and Q u = [ ] m 3 /s Finally, a third set of data was analyzed regarding the case of a lateral diversion, since it has some analogies compared to the side weir case. A lateral diversion represents an outflow which affects the main channel flow in a way similar to a side weir, even if the resulting flow field depends also on the conditions acting in the branch channel. Despite the analytical model does not take into account backwater effects from the outflow, which can occur for the 13

14 lateral diversion, the effect of the branch channel flow on the upstream and downstream flow is implicitly considered by the model, since it uses the boundary flow features Fr u and Fr d to close the balance of the mass and the energy within the control volume given by the portion of the main channel in front of the lateral outflow. Therefore, the application of the proposed model to the lateral diversion case may be performed in terms of the prediction of flow depth and flow discharge, with the restriction that the width of the branch channel cannot be specifically developed for side weirs. Data from Hsu et al. (2002) are used as a case of a subcritical, right-angled, lateral diversion, for which the flow conditions ranged within Fr u = [ ], Fr d = [ ] and Q u = [ ] m 3 /s The comparison between the experime the of the flow depth (Fig. 8), flow discharge (Fig. 9) and weir length (Fig. 10). The discharge coefficient C d for the calculation of r L regarding the data of the present study is chosen according to the formulation proposed by Borghei et al. (1999) which gives the best fit, whereas the data from Subramanya and Awasthy (1972) are predicted considering the formulation proposed by the same authors. The r L ratio is not computed for the lateral diversion case, since the side weir law cannot be used to model a branch channel. The results presented in Figs. 8, 9 and 10 show that the proposed analytical model gives a good prediction of the flow conditions in terms of the flow depth ratio and flow discharge 331 ratio and most of data are predicted within an error of 10 %. The validity of the De Marchi hypothesis is confirmed for the zero height side weir experiments as well as for the lateral diversion tests and most of the collected data are well predicted (Fig. 8). The comparison between the model prediction and the experimental data suggests 14

15 assumption can hold for the cases of subcritical flows along the side weir of zero height and fixed bed, and in particular the following ranges of validity have been verified: - Fr u = [ ], Fr d = [ ], r Q = [ ], r L = [ ] for the side weirs - Fr u = [ ], Fr d = [ ], r Q = [ ], r L = [1] for the lateral diversions. The mass balance is verified for all tests regarding the lateral diversion and for most of the present study experiments, whereas a greater scatter is observed for data coming from Subramanya and Awasthy (1972) resulting in a general underestimation of the diverted discharge for tests having a discharge ratio smaller than 0.5 (Fig. 9). The tests showing the underestimation are associated with large Froude numbers at the upstream and downstream sections (about Fr u > 0.7 and Fr d > 0.4). The errors for such flow conditions may arise from assuming the Coriolis coefficients equal to 1, that may lead to errors in the prediction of dimensionless ratios. By considering that larger Coriolis coefficients are expected at the downstream section than at the upstream one for a subcritical flow (i.e., d > u according to May et al. 2003) and that they should be taken into account in equation 3, the predicted flow depth ratio r Y without considering Coriolis coefficients may be overestimated. As a consequence, equation 4 suggests that the predicted discharge ratio r Q without considering the Coriolis coefficients may be underestimated. A preliminary application of the model by taking into account Coriolis coefficients showed that the percentage of Subramanya and Awasthy data reproduced within the error range 10 % regarding r Q changes from about 48% (in the case u = d = 1) to 72% (by assuming u = 1.15 and d = 1.75, as suggested by May et al. 2003). 358 The prediction of the length ratio is affected by higher errors (about 20 %), which may 359 be due to the approximation introduced by means of a constant value for the discharge 15

16 coefficient along the side weir and to the uncertainty related to the formulation chosen for such coefficient. Data regarding the present work are all predicted within the error range, whereas some data from Subramanya and Awasthy (1972), corresponding to about 25 % of their dataset, are again underestimated Fig. 8. Comparison between the experimental and predicted flow depth ratios for collected data. Fig. 9. Comparison between the experimental and predicted discharge ratios for collected data Fig. 10. Comparison between the experimental and predicted length ratios for collected data Comparison between the proposed model and the classical approaches The proposed model is herein compared with other models coming from the classical approaches in order to test its predictive capability and to highlight the original approach that has been proposed. The classical models usually aim to solve the system of differential equations (1) that govern the side weir flow in order to get the flow depth profile along the side weir length and, as a consequence, the diverted discharge Q s is obtained. In such procedure, a numerical scheme may be used to solve for the flow depth once the upstream or the downstream condition is known for, respectively, a supercritical or subcritical flow. The law for the diverted discharge is taken in a form similar to the weir overflow, and the discharge coefficient C d gets high importance in order to solve the entire system. Several studies have been focused on the determination of C d as a function of manifold parameters (as the upstream Froude number) and some of them have been reported in the present work. The problem of determining a generally valid and reliable formula for C d is still open. Subramanya and Awasthy (1972) and Hager (1987) proposed formulations for C d that 16

17 were specifically obtained for zero height crest of the side weir and they will be considered in the next analysis as the ones that are theoretically most appropriated to the present case. On the other hand, the proposed approach solves the problem in an integral formulation by setting the control volume around the side weir. In such a way, the proposed model does not solve the longitudinal water depth profile along the side weir, as the classical methods do, but the global variables, like the total diverted discharge Q s through the side weir, are obtained directly from the knowledge of the upstream and downstream flow conditions. According to Eqs , the proposed approach gives Q s without any need to know the formulation for the discharge coefficient C d, that is necessary only to get the length ratio r L. Finally, another difference with the classical approaches is that the proposed model is analytically formulated and it does not need any numerical schemes for the solution of the problem, since the system of equations (1) is not solved in the differential form. The classical approaches and the proposed one may be compared on the basis of their predictive capabilities in terms of the dimensionless ratios. Data presented in the previous Section are here used again and the proposed model is applied as well as the classical approach with the two formulations of C d given respectively by Subramanya and Awasthy (1972) and by Hager (1987). The classical models are implemented by means of an explicit numerical scheme based on the finite differences, that solves for the governing differential equations (1) by imposing the upstream and the downstream conditions, in the same framework of the proposed model. Since subcritical flow data are used, the algorithm is started by providing a downstream condition in terms of Fr d and Y d and the flow depth profile is then numerically solved toward upstream until the flow condition Fr u is found. A discretization step of L s /100 is chosen and the following formulations for C d, that depend on Fr u, are used: 17

18 409 C dhager 2 2 Fr Fr 2 u 2 u (9) 410 C dsubramanya & Awasthy Fr Fr 2 u 2 u (10) The comparison between the predictive capability of the proposed and the classical approaches are reported in Table 2 in terms of the following mean errors on the prediction of the dimensionless ratios: 414 ry N Ntest 1 r r Y expi Y modi r test i 1 Y expi (11) 415 rq N Ntest 1 r r Qexpi Q mod i r test i 1 Qexpi (12) 416 rl N Ntest 1 r r Lexpi Lmodi r test i 1 Lexpi (13) 417 With N test = number of analyzed tests for each data set Table 2. Predictive capabilities of the proposed model and the classical models (Hager 1987 and Subramanya and Awasthy 1972) on the analyzed data sets The results summarized in Table 2 show that the predictions of the proposed model are usually better than the two other models. The only case in which the proposed approach provides larger errors is on the r Y -prediction for data coming from Subramanya and Awasthy (1972) and from the present study: however, a slight difference with the prediction given by classical models is obtained for these cases. For all the other cases, the proposed model gives smaller errors than the classical models in terms of r Q - and r L -prediction, and the improvement is significant regarding the prediction of the discharge ratio for every data sets. Finally, it is worth to note that a very good 18

19 reproduction is achieved for r Q of data regarding lateral diversions by Hsu et al. (2002), whereas classical models predict larger errors: the resolution of the outflow process in the integral form given by the proposed model seems to be a better choice for lateral diversion flows. As it was already mentioned, the r L ratio is not computed for the lateral diversion case, since the side weir law cannot be used to model a branch channel Practical applications The proposed analytical model can be used for approximate solutions in the design practice and for verification purposes. The analytical results of the model highlight the governing effect of the downstream boundary condition on the side weir flow and a way to compute the downstream Froude number in subcritical flow condition is proposed. For applications to the field cases in which the side weirs are encountered along quite regular channels, one may consider a uniform flow regime as downstream boundary condition. In such a case, Fr d is directly related to the channel features in terms of flow roughness and bed slope S 0, whereas it is little influenced by the variation of the flow depth due to the diminishing of water discharge. As a matter of fact: 446 U Frd Ch S gy 0 (14) 447 Where C h 7.66 (Y/ r ) 1/6 is the Chézy coefficient, r [m] is the bed roughness and a wide rectangular section of the main channel is considered as a first approximation. According to eq. (14), the variation of Fr with the flow depth for a uniform flow regime is small, since the uniform flow slope is constant and the resistance coefficient C h changes only slightly with the flow depth. As a consequence, the downstream flow condition may be predicted a priori and the efficiency of the diversion may be planned by analyzing not only the side weir features (such as the length), but also the main channel characteristics. 19

20 The Froude graphs presented in Fig. 3 may be used to analyze the flow features in case of a side weir with zero height crest. For example, given L s of an existing or planned side weir and the features of the main channel (as B, C h, S 0 ), the Fr d is assessed by means of the eq. (14). Then, the knowledge of Fr d and the ratio r L allows to predict the upstream flow features in terms of Fr u through the use of the graph of Fig. 3c. Therefore, all the other characteristic ratios are calculated from Eqs. (3), (4) and (7), or, equivalently, from Figs. 3a-b-d, and the diverted discharge Q s is evaluated if the inflow Q u is given. Moreover, the flow variables Y, Q and U at the upstream and downstream sections are obtained and additional considerations may be deduced: for instance, the flow acceleration due to the lateral outflow may induce sediment transport mechanisms in case of a movable bed and the erosion of the bed in the upstream zone is then possible, whereas the aggradation can take place at the downstream section due to the decreasing of the flow velocity along the side weir (see Fig. 3d). A way to induce modifications the lateral outflow process may be studied by acting on the downstream condition if all the other conditions have to be the same: it is evident that the diverted discharge can be modified by changing the flow depth profile at the downstream reach, since, for instance, a backwater profile increases Q s in comparison with the case when a drawdown profile occurs. Finally, eq. 4 allows to investigate the discharge ratio as function of the Froude number and the trend of the maximum r Q that can be achieved under imposed conditions is analyzed by Fig. 11, in which r Q is plotted as a function of Fr d for given Fr u (Fig. 11a) and as a function of Fr u for given Fr d (Fig. 11b). In particular, there exists a limiting curve describing the maximum r Q, that is consistent with the assumption of subcritical flow, which is represented by the continuous line of Fig. 11a and by eq. 15: 20

21 478 r 1 Fr 3 Q max d 2 2 Frd 3/ 2 (15) On the other hand, the influence of the upstream Froude number on the discharge ratio is shown by Fig. 11b, in which r Q increases with Fr u toward an asymptotic value that depends on the imposed Fr d. The graphs of Fig. 11 represent another result of the analytical model that can be used (i) to predict the discharge to be diverted under the imposed flow conditions and (ii) to analyze the influence that a variation of the boundary conditions in terms of the Froude number has on the discharge ratio Fig. 11. Trend of r Q as function of Fr d (a) and Fr u (b) Summary and concluding remarks A new analytical solution of the one-dimensional flow problem for side weirs is presented in this paper. The proposed model is based on the De Marchi hypothesis and it is developed for the specific case of side weirs with a zero height crest acting on fixed bed and subcritical flow conditions. The governing equations of the conservation of mass and energy and the De Marchi equation are re-arranged in order to formulate the solution in terms of dimensionless ratios of flow and geometrical variables at the upstream and downstream cross-sections expressed as functions of the Froude number of the upstream (Fr u ) and the downstream (Fr d ) flow. The plane defined by Fr u and Fr d provides an original way to represent the side weir problem according to the flow features and the significant effect on the lateral outflow given by the downstream boundary condition, which actually governs subcritical flows, is focused in an explicit way. The analytical model provides a set of five equations (Eqs ) that, once the flow conditions at the upstream and downstream sections are given in terms of Fr, express the 21

22 solution as flow depth ratio, discharge ratio, length ratio and flow velocity ratio. The results are discussed with reference to the assumed case of subcritical flow and the sensitivity of the model with respect to the discharge coefficient is analyzed by considering six different formulations of C d, for which the maximum length ratio ranges within [1 4]. The proposed model is tested by using a new set of laboratory data as well as existing data 507 from the literature and most of data are predicted within an error range of 10 %, regarding 508 r Y and r Q, and of 20 % regarding r L. Since the zero height side weir model may represent other free-surface situations, a first promising application to the case of lateral diversion is performed and discussed by processing data from Hsu et al. (2002). Moreover, the proposed approach is compared with the classical ones to highlight its originality and to analyze its predictive capability. The classical approach is taken into account by means of the governing system of differential equations, that is numerically solved, and with the formulations for C d proposed by Hager (1987) and by Subramanya and Awasthy (1972). The predictive capabilities of the proposed and classical models are tested on the collected experimental data and it results that the performances of the proposed model in terms of the prediction of the dimensionless ratios are usually better than by using the classical methods. Finally, a practical procedure to calculate the geometrical and flow features of planned or existing side weirs is presented, starting from the uniform flow as downstream condition for which the eq. 14 takes implicitly into account the influence of the bottom roughness and the channel slope. Moreover, the maximum discharge ratio that can be achieved under the subcritical assumption is analyzed in terms of Fr u and Fr d and eq. 15 relates the limiting r Qmax with the given Fr d. The proposed approach provides an original interpretation of the lateral outflow phenomenon, that may be further investigated. For instance, additional studies could be 22

23 conducted to extend the proposed model for the case of supercritical flows. In such a situation, the model should take into account for the increasing trend of the Froude number along the side weir and the energy dissipation, that cannot be neglected anymore Notation The following symbols are used in this paper: B = width of the cross-section in the main channel; C d = discharge coefficient of the side weir; C h = dimensionless Chézy coefficient; D 50 = median diameter of bed material; E = specific energy head of the flow; E d = specific energy head of the flow at the downstream section of the side weir; E u = specific energy head of the flow at the upstream section of the side weir; Fr = Froude number; Fr d = Froude number of the flow at the downstream section of the side weir; Fr u = Froude number of the flow at the upstream section of the side weir; g = gravity acceleration; L s = side weir length; Q = water discharge flowing through a cross-section; Q d = water discharge downstream in the main channel; Q s = water discharge diverted over the side weir; Q u = water discharge upstream in the main channel; q s = discharge diverted through the side weir per unit length; R = relative roughness; Re = Reynolds number; 23

24 r L = L s / B = length ratio; r Q = Q s / Q u = flow discharge ratio; r U = U d / U u = flow velocity ratio; r Y = Y d / Y u = flow depth ratio; S 0 = bed slope of the main channel; U = average flow velocity at a cross-section; x = longitudinal axis; Y = flow depth at a cross-section; Y d = flow depth at the downstream section of the side weir; Y u = flow depth at the upstream section of the side weir; = Coriolis coefficient; = mean error between prediction models and analyzed data sets; 564 r Y = mean error on prediction of r Y ratio; 565 r Q = mean error on prediction of r Q ratio; 566 r L = mean error on prediction of r L ratio; r = bed roughness; = dimensionless flow function of De Marchi solution Acknowledgments The results presented in this paper are part of the PhD thesis of the author (Michelazzo 2014), which was jointly supervised by Prof. E. Paris (University of Florence) and by Prof. H. Oumeraci (University of Braunschweig) within the International Course of Research Doctorate Mitigation of Risk due to Natural Hazards on Structures and Infrastructures

25 References Awasthy, S. C. (1970). Hydraulic behavior of side weirs. Master Thesis, Indian Institute of Technology, Kanpur, India. Borghei, S. M., Jalili, M. R., and Ghodsian, M. (1999). Discharge coefficient for sharpcrested side weirs in subcritical flow. J. Hydraul. Eng.-ASCE, 125(10), Cheong, H. F. (1991). Discharge coefficient of lateral diversion from trapezoidal channel. J. Irrig. Drain. E.-ASCE, 117(4), De Marchi, G. (1934). Saggio di teoria del funzionamento degli stramazzi laterali., 11(11), Durga Rao, K. H. V. and Pillai, C. R. S. (2008). Study of flow over side weirs under supercritical conditions. Water. Resour. Manag., 22(1), Emiroglu, M. E., Agaccioglu, H., and Kaya, N. (2011). Discharging capacity of rectangular side weirs in straight open channels. Flow Meas. Instrum., 22(4), Hager, W. H. (1987). Lateral outflow over side weirs. J. Hydraul. Eng.-ASCE, 113(4), Hsu, C. C., Tang, C. J., Lee, W. J., and Shieh, M. Y. (2002). Subcritical 90 equal-width open-channel dividing flow. J. Hydraul. Eng.-ASCE, 128(7), Lee, K. L., and Holley, E. R. (2002). Physical modeling for side-channel weirs. CRWR Online Rep. 02-2, Center for Research in Water Resources, Univ. of Texas, Austin, Tex. Li, C. W., and Zeng, C. (2009). 3D numerical modelling of flow divisions at open channel junctions with or without vegetation. Adv. Water Resour., 32(1), May, R. W. P., Bromwich, B. C., Gasowski, Y., and Rickard, C. E. (2003). Hydraulic 598 design of side weirs. Thomas Telford Publishing, London: p

26 experimental hydro- sertation, University of Florence (Italy) - University of Braunschweig (Germany), < Montes, S. (1998). Hydraulics of open channel flow. Reston: ASCE Press, c1998. Namaee, M. R., Jalaledini, M. S., Habibi, M., Yazdi, S. R. S., and Azar, M. G. (2013). Discharge coefficient of a broad crested side weir in an earthen channel. Wa. Sci. Technol., 13(1), Neary, V. S., and Odgaard, A. J. (1993). Three-dimensional flow structure at open channel diversions. J. Hydraul. Eng.-ASCE, 119(11), Neary, V. S., Sotiropoulos, F., and Odgaard, A. J. (1999). Three-dimensional numerical model of lateral-intake inflows. J. Hydraul. Eng.-ASCE, 125(2), J. Hydraul. Res.-IAHR, 39(1), Paris, E., Solari, L., and Bechi, G. (2012). Applicability of the De Marchi Hypothesis for Side Weir Flow in the Case of Movable Beds. J. Hydraul. Eng.-ASCE, 138(7), Ranga Raju, K. G., Prasad, B., and Gupta, S. K. (1979). Side weir in rectangular channel. J. Hydr. Eng. Div.-ASCE, 105(5), Rosier, B. (2007). Interaction of a side weir overflow with bed-load transport and bed morphology in a channel. PhD Thesis, 3872, Ecole Polytechnique Fédérale de Lausanne EPFL, Switzerland. Singh, R., Manivannan, D., and Satyanarayana, T. (1994). Discharge coefficient of rectangular side weirs. J. Irrig. Drain. E.-ASCE, 120(4),

27 Subramanya, K., and Awasthy, S. C. (1972). Spatially Varied Flow over Side-Weirs. J. Hydr. Eng. Div.-ASCE, 98(1), Vasquez, J. A. (2005). Two-dimensional numerical simulation of flow diversions. Proc., 17th Canadian Hydrotechnical Conference, Vatankhah, A. R. (2012a). Analytical solution for water surface profile along a side weir in a triangular channel. Flow Meas. Instrum., 23(1), Vatankhah, A. R. (2012b). New Solution Method for Water Surface Profile along a Side Weir in a Circular Channel. J. Irrig. Drain. E.-ASCE, 138(10), Vatankhah, A. R. (2013). Water Surface Profiles along a Rectangular Side Weir in a U- Shaped Channel (Analytical Findings). J. Hydrol. Eng., 18(5), Venutelli, M. (2008). Method of solution of nonuniform flow with the presence of rectangular side weir. J. Irrig. Drain. E.-ASCE, 134(6), Zhou, J. and Zeng, C. (2009). 3-D hybrid LES-RANS model for simulation of openchannel T-diversion flows. Water Science and Engineering 2009, 2(3),

28 Table 1. Summary of conditions and results for the performed tests (for each test: main channel width B = 0.3 m, Test side weir with zero height crest). Side weir Inflow Downstream Diverted Upstream Downstream length Sluice gate discharge discharge discharge flow depth flow depth configuration L s [m] Q u [m 3 /s] Q d [m 3 /s] Q s [m 3 /s] Y u [m] Y d [m] B Setting B Setting B Setting B Setting B Setting B Setting B Setting B Setting B Setting B Setting C Setting C Setting C Setting C Setting C Setting C Setting C Setting C Setting C Setting C Setting

29 Table 2. Predictive capabilities of the proposed model and the classical models (Hager 1987 and Subramanya and Awasthy 1972) on the analyzed data sets. Subramanya and Awasthy (1972) DATA SETS Present Study Hsu et al. (2002) Proposed model ry [%] rq [%] rl [%] Hager (1987) model Subramanya and Awasthy (1972) model Proposed model Hager (1987) model Subramanya and Awasthy (1972) model Proposed model Hager (1987) model Subramanya and Awasthy (1972) model

Free Flow Below Skew Sluice Gate

Free Flow Below Skew Sluice Gate International Journal of Engineering Research and Development e-issn: 2278-67X, p-issn: 2278-8X, www.ijerd.com Volume, Issue 3 (March 24), PP.44-52 Talib Mansoor Civil Engineering Department, Aligarh Muslim

More information

EFFECT OF BAFFLE BLOCKS ON THE PERFORMANCE OF RADIAL HYDRAULIC JUMP

EFFECT OF BAFFLE BLOCKS ON THE PERFORMANCE OF RADIAL HYDRAULIC JUMP Fourth International Water Technology Conference IWTC 99, Alexandria, Egypt 255 EFFECT OF BAFFLE BLOCKS ON THE PERFORMANCE OF RADIAL HYDRAULIC JUMP O. S. Rageh Irrigation & Hydraulics Dept., Faculty of

More information

Discharge Coefficient for Sharp-Crested Side Weir in Supercritical Flow

Discharge Coefficient for Sharp-Crested Side Weir in Supercritical Flow ENGINEER - Vol. XXXIX, No. 02, pp. 17-24,2006 The Institution of Engineers, Sri Lanka Discharge Coefficient for Sharp-Crested Side Weir in Supercritical Flow K.P.P. Pathirana, M.M. Munas and A.L.A. Jaleel

More information

Flow Characteristics and Modelling of Head-discharge Relationships for Weirs

Flow Characteristics and Modelling of Head-discharge Relationships for Weirs Chapter 8 Flow Characteristics and Modelling of Head-discharge Relationships for Weirs 8.1 Introduction In Chapters 5 and 7, the formulations of the numerical models for the simulations of flow surface

More information

DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING Urban Drainage: Hydraulics. Solutions to problem sheet 2: Flows in open channels

DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING Urban Drainage: Hydraulics. Solutions to problem sheet 2: Flows in open channels DEPRTMENT OF CIVIL ND ENVIRONMENTL ENGINEERING Urban Drainage: Hydraulics Solutions to problem sheet 2: Flows in open channels 1. rectangular channel of 1 m width carries water at a rate 0.1 m 3 /s. Plot

More information

Formation Of Hydraulic Jumps On Corrugated Beds

Formation Of Hydraulic Jumps On Corrugated Beds International Journal of Civil & Environmental Engineering IJCEE-IJENS Vol:10 No:01 37 Formation Of Hydraulic Jumps On Corrugated Beds Ibrahim H. Elsebaie 1 and Shazy Shabayek Abstract A study of the effect

More information

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis.

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis. OPEN CHANNEL FLOW Open channel flow is a flow of liquid, basically water in a conduit with a free surface. The open channel flows are driven by gravity alone, and the pressure gradient at the atmospheric

More information

FORMATION OF HYDRAULIC JUMPS ON CORRUGATED BEDS

FORMATION OF HYDRAULIC JUMPS ON CORRUGATED BEDS International Journal of Civil & Environmental Engineering IJCEE-IJENS Vol: 10 No: 01 40 FORMATION OF HYDRAULIC JUMPS ON CORRUGATED BEDS Ibrahim H. Elsebaie 1 and Shazy Shabayek Abstract A study of the

More information

A note on critical flow section in collector channels

A note on critical flow section in collector channels Sādhan ā, Vol. 26, Part 5, October 2001, pp. 439 445. Printed in India A note on critical flow section in collector channels 1. Introduction SUBHASISH DEY Department of Civil Engineering, Indian Institute

More information

P10.5 Water flows down a rectangular channel that is 4 ft wide and 3 ft deep. The flow rate is 15,000 gal/min. Estimate the Froude number of the flow.

P10.5 Water flows down a rectangular channel that is 4 ft wide and 3 ft deep. The flow rate is 15,000 gal/min. Estimate the Froude number of the flow. P10.5 Water flows down a rectangular channel that is 4 ft wide and ft deep. The flow rate is 15,000 gal/min. Estimate the Froude number of the flow. Solution: Convert the flow rate from 15,000 gal/min

More information

Guo, James C.Y. (1999). "Critical Flow Section in a Collector Channel," ASCE J. of Hydraulic Engineering, Vol 125, No. 4, April.

Guo, James C.Y. (1999). Critical Flow Section in a Collector Channel, ASCE J. of Hydraulic Engineering, Vol 125, No. 4, April. Guo, James C.Y. (1999). "Critical Flow Section in a Collector Channel," ASCE J. of Hydraulic Engineering, Vol 15, No. 4, April. CRITICAL FLOW SECTION IN A COLLECTOR CHANNEL By James C.Y. Guo, PhD, P.E.

More information

Laboratory experiences on open channel flow (in collaboration with Dr. Ing. Luca Milanesi)

Laboratory experiences on open channel flow (in collaboration with Dr. Ing. Luca Milanesi) Classwork 8 Laboratory experiences on open channel flow (in collaboration with Dr. Ing. Luca Milanesi) Why a practical lesson on open channel flow? In the first part of the course we studied open channel

More information

OPEN CHANNEL FLOW. One-dimensional - neglect vertical and lateral variations in velocity. In other words, Q v = (1) A. Figure 1. One-dimensional Flow

OPEN CHANNEL FLOW. One-dimensional - neglect vertical and lateral variations in velocity. In other words, Q v = (1) A. Figure 1. One-dimensional Flow OPEN CHANNEL FLOW Page 1 OPEN CHANNEL FLOW Open Channel Flow (OCF) is flow with one boundary exposed to atmospheric pressure. The flow is not pressurized and occurs because of gravity. Flow Classification

More information

Hydraulics Part: Open Channel Flow

Hydraulics Part: Open Channel Flow Hydraulics Part: Open Channel Flow Tutorial solutions -by Dr. K.N. Dulal Uniform flow 1. Show that discharge through a channel with steady flow is given by where A 1 and A 2 are the sectional areas of

More information

Presented by: Civil Engineering Academy

Presented by: Civil Engineering Academy Presented by: Civil Engineering Academy Open-Channel Flow Uniform Flow (See CERM Ch. 19) Characterized by constant depth volume, and cross section. It can be steady or unsteady Non-uniform Flow *Not on

More information

1.060 Engineering Mechanics II Spring Problem Set 8

1.060 Engineering Mechanics II Spring Problem Set 8 1.060 Engineering Mechanics II Spring 2006 Due on Monday, May 1st Problem Set 8 Important note: Please start a new sheet of paper for each problem in the problem set. Write the names of the group members

More information

Experiment 7 Energy Loss in a Hydraulic Jump

Experiment 7 Energy Loss in a Hydraulic Jump Experiment 7 Energ Loss in a Hdraulic Jump n Purpose: The purpose of this experiment is to examine the transition from supercritical (rapid) flow to subcritical (slow) flow in an open channel and to analze

More information

COMPARISON OF LABORATORY AND FIELD MEASUREMENTS OF BRIDGE PIER SCOUR

COMPARISON OF LABORATORY AND FIELD MEASUREMENTS OF BRIDGE PIER SCOUR COMPARISON OF LABORATORY AND FIELD MEASUREMENTS OF BRIDGE PIER SCOUR LEE, SEUNGOH, STURM, T. W., School of Civil and Environ. Engrg., Georgia Institute of Technology Atlanta, GA 30332-0512 USA GOTVALD,

More information

3.2 CRITICAL DEPTH IN NONRECTANGULAR CHANNELS AND OCCUR- RENCE OF CRITICAL DEPTH

3.2 CRITICAL DEPTH IN NONRECTANGULAR CHANNELS AND OCCUR- RENCE OF CRITICAL DEPTH 3.2 CRITICAL DEPTH IN NONRECTANGULAR CHANNELS AND OCCUR- RENCE OF CRITICAL DEPTH Critical Depth in Non-Rectangular Channels Consider an irregular channel: da w dd dd d Specific energy is defined as: E

More information

Minimum Specific Energy and Critical Flow Conditions in Open Channels

Minimum Specific Energy and Critical Flow Conditions in Open Channels Minimum Specific Energy and Critical Flow Conditions in Open Channels by H. Chanson 1 Abstract : In open channels, the relationship between the specific energy and the flow depth exhibits a minimum, and

More information

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis.

Closed duct flows are full of fluid, have no free surface within, and are driven by a pressure gradient along the duct axis. OPEN CHANNEL FLOW Open channel flow is a flow of liquid, basically water in a conduit with a free surface. The open channel flows are driven by gravity alone, and the pressure gradient at the atmospheric

More information

Dealing with Sedimental Transport Over Partly Non-Erodible Bottoms

Dealing with Sedimental Transport Over Partly Non-Erodible Bottoms Utah State University DigitalCommons@USU International Junior Researcher and Engineer Workshop on Hydraulic Structures Jun 17th, 12:00 AM - Jun 20th, 12:00 AM Dealing with Sedimental Transport Over Partly

More information

Gradually Varied Flow I+II. Hydromechanics VVR090

Gradually Varied Flow I+II. Hydromechanics VVR090 Gradually Varied Flow I+II Hydromechanics VVR090 Gradually Varied Flow Depth of flow varies with longitudinal distance. Occurs upstream and downstream control sections. Governing equation: dy dx So Sf

More information

GEOMETRY EFFECT ON FLOW AND SEDIMENT DEPOSITION PATTERNS IN SHALLOW BASINS

GEOMETRY EFFECT ON FLOW AND SEDIMENT DEPOSITION PATTERNS IN SHALLOW BASINS Annual Journal of Hydraulic Engineering, JSCE, Vol.54, 21, February GEOMETRY EFFECT ON FLOW AND SEDIMENT DEPOSITION PATTERNS IN SHALLOW BASINS Sameh A. KANTOUSH 1, Tetsuya SUMI 2 and Anton J. SCHLEISS

More information

PART 2:! FLUVIAL HYDRAULICS" HYDROEUROPE

PART 2:! FLUVIAL HYDRAULICS HYDROEUROPE PART 2:! FLUVIAL HYDRAULICS" HYDROEUROPE 2009 1 HYDROEUROPE 2009 2 About shear stress!! Extremely complex concept, can not be measured directly!! Computation is based on very primitive hypotheses that

More information

Prediction of bed form height in straight and meandering compound channels

Prediction of bed form height in straight and meandering compound channels Water Resources Management III 311 Prediction of bed form height in straight and meandering compound channels R. D. Karamisheva, J. F. Lyness, W. R. C. Myers, J. O Sullivan & J. B. C. Cassells School of

More information

Local Scouring due to Flow Jet at Downstream of Rectangular Sharp-Crested Weirs

Local Scouring due to Flow Jet at Downstream of Rectangular Sharp-Crested Weirs Local Scouring due to Flow Jet at Downstream of Rectangular Sharp-Crested Weirs DEHGHANI, AMIR. AHMAD 1, BASHIRI, HAMID and MESHKATI SHAHMIRZADI, MOHAMMAD. EBRAHIM 3 1,3 Dept. of Water Engineering, Gorgan

More information

Inclined Rectangular Weir-Flow Modeling

Inclined Rectangular Weir-Flow Modeling Earth Science India, eissn: 0974 850 Vol. 4(II), April, 011, pp. 57-67 Inclined Rectangular Weir-Flow Modeling M.N. Shesha Prakash 1, M. B. Ananthayya and Gicy M. Kovoor 1 Vidya Vikas Institute of Engineering

More information

Chapter 4: Non uniform flow in open channels

Chapter 4: Non uniform flow in open channels Chapter 4: Non uniform flow in open channels Learning outcomes By the end of this lesson, students should be able to: Relate the concept of specific energy and momentum equations in the effect of change

More information

Head Discharge Relationship of Thin Plated Rectangular Lab Fabricated Sharp Crested Weirs

Head Discharge Relationship of Thin Plated Rectangular Lab Fabricated Sharp Crested Weirs Journal of Applied Fluid Mechanics, Vol. 9, No. 3, pp. 1231-1235, 2016. Available online at www.jafmonline.net, ISSN 1735-3572, EISSN 1735-3645. DOI: 10.18869/acadpub.jafm.68.228.23128 Head Discharge Relationship

More information

Annex 3 Side weirs and oblique weirs

Annex 3 Side weirs and oblique weirs Annex 3 Side weirs and oblique weirs 3.1 ntroduction Most of the weirs described in this book serve mainly to measure discharges. Some, however, such as those described in Chapters 4 and 6 can also be

More information

Hydraulics Prof. Dr. Arup Kumar Sarma Department of Civil Engineering Indian Institute of Technology, Guwahati

Hydraulics Prof. Dr. Arup Kumar Sarma Department of Civil Engineering Indian Institute of Technology, Guwahati Hydraulics Prof. Dr. Arup Kumar Sarma Department of Civil Engineering Indian Institute of Technology, Guwahati Module No. # 04 Gradually Varied Flow Lecture No. # 07 Rapidly Varied Flow: Hydraulic Jump

More information

VARIED FLOW IN OPEN CHANNELS

VARIED FLOW IN OPEN CHANNELS Chapter 15 Open Channels vs. Closed Conduits VARIED FLOW IN OPEN CHANNELS Fluid Mechanics, Spring Term 2011 In a closed conduit there can be a pressure gradient that drives the flow. An open channel has

More information

EFFECT OF GRAIN DENSITY ON PLANE BED FRICTION. Václav Matoušek, Vojtěch Bareš, Jan Krupička, Tomáš Picek, Štěpán Zrostlík

EFFECT OF GRAIN DENSITY ON PLANE BED FRICTION. Václav Matoušek, Vojtěch Bareš, Jan Krupička, Tomáš Picek, Štěpán Zrostlík ISBN 978-83-927084-8-3 ISSN 0867-7964 EFFECT OF GRAIN DENSITY ON PLANE BED FRICTION Václav Matoušek, Vojtěch Bareš, Jan Krupička, Tomáš Picek, Štěpán Zrostlík Czech Technical University in Prague, Faculty

More information

FLOW MODELLING OF INCLINED TRAPEZOIDAL WEIR WITH A NEW APPROACH

FLOW MODELLING OF INCLINED TRAPEZOIDAL WEIR WITH A NEW APPROACH International Journal of Science, Environment and Technology, Vol. 7, No 3, 018, 83 834 ISSN 78-3687 (O) 77-663X (P) FLOW MODELLING OF INCLINED TRAPEZOIDAL WEIR WITH A NEW APPROACH 1 M.N. Shesha Prakash,

More information

CIE4491 Lecture. Hydraulic design

CIE4491 Lecture. Hydraulic design CIE4491 Lecture. Hydraulic design Marie-claire ten Veldhuis 19-9-013 Delft University of Technology Challenge the future Hydraulic design of urban stormwater systems Focus on sewer pipes Pressurized and

More information

HEAD LOSSES IN SEWER JUNCTION

HEAD LOSSES IN SEWER JUNCTION E-proceedings of the 6 th IAHR World Congress 8 June July, 0, The Hague, the Netherlands HEAD LOSSES IN SEWER JUNCTION CORRADO GISONNI () & MICHAEL PFISTER () () Dept. of Civil Engineering, Design, Construction

More information

NPTEL Quiz Hydraulics

NPTEL Quiz Hydraulics Introduction NPTEL Quiz Hydraulics 1. An ideal fluid is a. One which obeys Newton s law of viscosity b. Frictionless and incompressible c. Very viscous d. Frictionless and compressible 2. The unit of kinematic

More information

THEORY AND GEOMETRY COMPARISON AMONG INCLINED FREE - OVER SILL - REPELLED HYDRAULIC JUMPS

THEORY AND GEOMETRY COMPARISON AMONG INCLINED FREE - OVER SILL - REPELLED HYDRAULIC JUMPS ABSTRACT THEORY AND GEOMETRY COMPARISON AMONG INCLINED FREE - OVER SILL - REPELLED HYDRAULIC JUMPS J. D. Demetriou In this study, which is based on recent laboratory measurements by the author and further

More information

Real scale investigation of interaction between a supercritical flow and a bottom sill. 1: physical aspects and time-averaged pressures on sill

Real scale investigation of interaction between a supercritical flow and a bottom sill. 1: physical aspects and time-averaged pressures on sill Real scale investigation of interaction between a supercritical flow and a bottom sill. 1: physical aspects and time-averaged pressures on sill D. Borsani, E. Larcan, S. Mambretti & E. Orsi Dipartimento

More information

NUMERICAL SIMULATION OF EROSION PROCESSES ON CROSSBAR BLOCK RAMPS

NUMERICAL SIMULATION OF EROSION PROCESSES ON CROSSBAR BLOCK RAMPS E-proceedings of the 36 th IAHR World Congress NUMERICAL SIMULATION OF EROSION PROCESSES ON CROSSBAR BLOCK RAMPS MARIO OERTEL (1), JAN P. BALMES (2), DANIEL B. BUNG (3) (1) Hydraulic Engineering Section,

More information

Head loss coefficient through sharp-edged orifices

Head loss coefficient through sharp-edged orifices Head loss coefficient through sharp-edged orifices Nicolas J. Adam, Giovanni De Cesare and Anton J. Schleiss Laboratory of Hydraulic Constructions, Ecole Polytechnique fédérale de Lausanne, Lausanne, Switzerland

More information

Saudi Journal of Civil Engineering

Saudi Journal of Civil Engineering Saudi Journal of Civil Engineering A Publication by Scholars Middle East Publishers, Dubai, United Arab Emirates ISSN 2523-2657 (Print) ISSN 2523-2231 (Online) Influence of Gravel Beds on Erosion of Sand

More information

Laboratory Investigation of Submerged Vane Shapes Effect on River Banks Protection

Laboratory Investigation of Submerged Vane Shapes Effect on River Banks Protection Australian Journal of Basic and Applied Sciences, 5(12): 1402-1407, 2011 ISSN 1991-8178 Laboratory Investigation of Submerged Vane Shapes Effect on River Banks Protection Touraj Samimi Behbahan Department

More information

Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati

Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati Advanced Hydraulics Prof. Dr. Suresh A. Kartha Department of Civil Engineering Indian Institute of Technology, Guwahati Module - 5 Channel Transitions Lecture - 1 Channel Transitions Part 1 Welcome back

More information

IGHEM 2008 MILANO 3 rd -6 th September International Group for Hydraulic Efficiency Measurements

IGHEM 2008 MILANO 3 rd -6 th September International Group for Hydraulic Efficiency Measurements ENERGY LOSS EFFICIENCY MEASURED IN HYDRAULIC JUMPS WITHIN SLOPED CHANNELS J Demetriou* and D Dimitriou** *National Technical University of Athens, Greece School of Civil Engineering Hydraulics Laboratory

More information

A Study of The Turbulent Flows in Sloping and Adversely Sloping Rectangular Culvert

A Study of The Turbulent Flows in Sloping and Adversely Sloping Rectangular Culvert International Journal of Civil & Environmental Engineering IJCEE-IJENS Vol:12 No:06 85 A Study of The Turbulent Flows in Sloping and Adversely Sloping Rectangular Culvert Abdullah I Alhomidan College of

More information

Flow Field Investigation in a Rectangular Shallow Reservoir using UVP, LSPIV and numerical model

Flow Field Investigation in a Rectangular Shallow Reservoir using UVP, LSPIV and numerical model Flow Field Investigation in a Rectangular Shallow Reservoir using UVP, LSPIV and numerical model S AMEH KANTOUSH, ERIK BOLLAERT, GIOVANNI DE CESARE, JEAN-LOUIS BOILLAT and ANTON SCHLEISS Ecole Polytechnique

More information

Chapter 3.8: Energy Dissipators. By Dr. Nuray Denli Tokyay

Chapter 3.8: Energy Dissipators. By Dr. Nuray Denli Tokyay Chapter 3.8: Energy Dissipators By Dr. Nuray Denli Tokyay 3.1 Introduction A stilling basin is a short length of paved channel placed at the foot of a spillway or any other source of supercritical flow

More information

Development of a discharge equation for side weirs using artificial neural networks

Development of a discharge equation for side weirs using artificial neural networks 31 IWA Publishing 2005 Journal of Hydroinformatics 07.1 2005 Development of a discharge equation for side weirs using artificial neural networks Mohamed Khorchani and Olivier Blanpain ABSTRACT Flow over

More information

VARIATION OF MANNING S ROUGHNESS COEFFICIENT WITH SEEPAGE IN SAND-BED CHANNEL *Satish Patel 1 and Bimlesh Kumar 2

VARIATION OF MANNING S ROUGHNESS COEFFICIENT WITH SEEPAGE IN SAND-BED CHANNEL *Satish Patel 1 and Bimlesh Kumar 2 International Journal of Science, Environment and Technology, Vol. 5, No 6, 2016, 3678 3685 ISSN 2278-3687 (O) 2277-663X (P) VARIATION OF MANNING S ROUGHNESS COEFFICIENT WITH SEEPAGE IN SAND-BED CHANNEL

More information

Open Channel Hydraulics III - Sharpcrested

Open Channel Hydraulics III - Sharpcrested PDHonline Course H140 (2 PDH) Open Channel Hydraulics III - Sharpcrested Weirs Instructor: Harlan H. Bengtson, Ph.D., PE 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone

More information

AN EXPERIMENTAL AND THEORETICAL INVESTIGATION OF SIDE WEIRS

AN EXPERIMENTAL AND THEORETICAL INVESTIGATION OF SIDE WEIRS University of Southern Queensland Faculty of Engineering and Surveying AN EXPERIMENTAL AND THEORETICAL INVESTIGATION OF SIDE WEIRS A dissertation submitted by David Selwyn Rowlings in fulfilment of the

More information

Design of Stilling Basins using Artificial Roughness

Design of Stilling Basins using Artificial Roughness Design of Stilling Basins using Artificial Roughness N. AboulAtta 1, G. Ezizah 2, N. Yousif 3, S. Fathy 4 Abstract The stilling basins are commonly used to dissipate the energy and protect the downstream

More information

Hydromechanics: Course Summary

Hydromechanics: Course Summary Hydromechanics: Course Summary Hydromechanics VVR090 Material Included; French: Chapters to 9 and 4 + Sample problems Vennard & Street: Chapters 8 + 3, and (part of it) Roberson & Crowe: Chapter Collection

More information

Flow and Bed Topography in a 180 Curved Channel

Flow and Bed Topography in a 180 Curved Channel Flow and Bed Topography in a 180 Curved Channel Jae Wook Jung 1, Sei Eui Yoon 2 Abstract The characteristics of flow and bed topography has been analyzed by changing the bed materials in a 180-degree,

More information

THE EFFECTS OF OBSTACLES ON SURFACE LEVELS AND BOUNDARY RESISTANCE IN OPEN CHANNELS

THE EFFECTS OF OBSTACLES ON SURFACE LEVELS AND BOUNDARY RESISTANCE IN OPEN CHANNELS Manuscript submitted to 0th IAHR Congress, Thessaloniki, 4-9 August 00 THE EFFECTS OF OBSTACLES ON SURFACE LEVELS AND BOUNDARY RESISTANCE IN OPEN CHANNELS J. D. FENTON Department of Civil and Environmental

More information

An Examination of Rectangular Side Weir Discharge Coefficient Equations under Subcritical Condition

An Examination of Rectangular Side Weir Discharge Coefficient Equations under Subcritical Condition International Journal of Hydraulic Engineering 014, 3(1): 434 DOI: 10.593/j.ijhe.0140301.03 An Examination of Rectangular Side Weir Discharge Madjid Delkash *, Babak Ebrazi Bakhshayesh Department of Civil

More information

CHAPTER FOUR Flow Measurement and Control

CHAPTER FOUR Flow Measurement and Control CHAPTER FOUR Flow Measurement and Control 4.1 INTRODUCTION Proper treatment plant operation requires knowledge of the rate at which flow enters the plant and controlling the flow between unit processes.

More information

Lateral Inflow into High-Velocity Channels

Lateral Inflow into High-Velocity Channels Lateral Inflow into High-Velocity Channels by Richard L. Stockstill PURPOSE: This Coastal and Hydraulics Engineering Technical Note (CHETN) investigates lateral flow discharging into a high-velocity channel.

More information

INFLUENCE OF OFF-TAKE ANGLES ON FLOW DISTRIBUTION PATTERN AT CONCAVE CHANNEL BIFURCATION

INFLUENCE OF OFF-TAKE ANGLES ON FLOW DISTRIBUTION PATTERN AT CONCAVE CHANNEL BIFURCATION INFLUENCE OF OFF-TAKE ANGLES ON FLOW DISTRIBUTION PATTERN AT CONCAVE CHANNEL BIFURCATION 1 2 2 OBASI, N.L., AGUNWAMBA, J.C. AND EGBUNIWE, N. 1. Department of Civil Engineering, Enugu State University of

More information

Open Channel Flow Part 2. Ch 10 Young, notes, handouts

Open Channel Flow Part 2. Ch 10 Young, notes, handouts Open Channel Flow Part 2 Ch 10 Young, notes, handouts Uniform Channel Flow Many situations have a good approximation d(v,y,q)/dx=0 Uniform flow Look at extended Bernoulli equation Friction slope exactly

More information

VELOCITY AND WATER DEPTH ANALYSIS ON DIFFERENT TYPES OF BLOCK RAMPS

VELOCITY AND WATER DEPTH ANALYSIS ON DIFFERENT TYPES OF BLOCK RAMPS VELOCITY AND WATER DEPTH ANALYSIS ON DIFFERENT TYPES OF BLOCK RAMPS Markus J. Studer 1 and Anton J. Schleiss 2 1 Laboratory of Hydraulic Constructions (LCH), Ecole Polytechnique Fédérale de Lausanne (EPFL),

More information

Study of Flow Characteristics of Contracted Sharp Crested Rectangular Weir Rahul Pandey 1, Dr.S.K.Mittal 2 and Prof. M.K.

Study of Flow Characteristics of Contracted Sharp Crested Rectangular Weir Rahul Pandey 1, Dr.S.K.Mittal 2 and Prof. M.K. Study of Flow Characteristics of Contracted Sharp Crested Rectangular Weir Rahul Pandey 1, Dr.S.K.Mittal 2 and Prof. M.K.Choudhary 3 1 M.Tech Student, Department of Civil Engineering, MANIT Bhopal (M.P.),

More information

THE EFFECT OF THICKNESS OF PILLAR IN THE CHANNEL BEND TO CHANGES THE COEFFICIENT OF SUPERELEVATION

THE EFFECT OF THICKNESS OF PILLAR IN THE CHANNEL BEND TO CHANGES THE COEFFICIENT OF SUPERELEVATION Journal Engineering Science and Technology Vol. 11, No. 5 (2016) 745-754 School Engineering, Taylor s University THE EFFECT OF THICKNESS OF PILLAR IN THE CHANNEL BEND TO CHANGES THE COEFFICIENT OF SUPERELEVATION

More information

Experimental Study of Discharge Characteristics in a Compound Meandering River

Experimental Study of Discharge Characteristics in a Compound Meandering River American Journal of Engineering Research (AJER) e-issn : 2320-0847 p-issn : 2320-0936 Volume-02, Issue-07, pp-136-140 www.ajer.org Research Paper Open Access Experimental Study of Discharge Characteristics

More information

Simulation of Transcritical Flow in Hydraulic structures

Simulation of Transcritical Flow in Hydraulic structures Simulation of Transcritical Flow in Hydraulic structures Cornelius E Agu 1 Geir Elseth Bernt Lie 3 1,3 Faculty of Technology, Telemark University College, Norway, {corneliuseagu,berntlie}@hitno Statoil

More information

THE HYDRAULIC PERFORMANCE OF ORIENTED SPUR DIKE IMPLEMENTATION IN OPEN CHANNEL

THE HYDRAULIC PERFORMANCE OF ORIENTED SPUR DIKE IMPLEMENTATION IN OPEN CHANNEL Tenth International Water Technology Conference, IWTC10 2006, Alexandria, Egypt 281 THE HYDRAULIC PERFORMANCE OF ORIENTED SPUR DIKE IMPLEMENTATION IN OPEN CHANNEL Karima Attia 1 and Gamal El Saied 2 1

More information

BANK PROTECTION AT THE OUTER SIDE OF CURVED CHANNELS BY AN UNDULATED MACROROUGH CONCRETE WALL

BANK PROTECTION AT THE OUTER SIDE OF CURVED CHANNELS BY AN UNDULATED MACROROUGH CONCRETE WALL 4 th IAHR International Symposium on Hydraulic Structures, 9-11 February 2012, Porto, Portugal, ISBN: 978-989-8509-01-7 BANK PROTECTION AT THE OUTER SIDE OF CURVED CHANNELS BY AN UNDULATED MACROROUGH CONCRETE

More information

EXPERIMENTAL STUDY OF BACKWATER RISE DUE TO BRIDGE PIERS AS FLOW OBSTRUCTIONS

EXPERIMENTAL STUDY OF BACKWATER RISE DUE TO BRIDGE PIERS AS FLOW OBSTRUCTIONS Tenth International Water Technology Conference, IWTC1 6, Alexandria, Egypt 19 EXPERIMENTAL STUDY OF BACKWATER RISE DUE TO BRIDGE PIERS AS FLOW OBSTRUCTIONS Kassem Salah El-Alfy Associate Prof., Irrigation

More information

CEE 3310 Open Channel Flow, Nov. 26,

CEE 3310 Open Channel Flow, Nov. 26, CEE 3310 Open Channel Flow, Nov. 6, 018 175 8.10 Review Open Channel Flow Gravity friction balance. y Uniform Flow x = 0 z = S 0L = h f y Rapidly Varied Flow x 1 y Gradually Varied Flow x 1 In general

More information

Development of Discharge Prediction Model for Trapezoidal Canals using Simple Portable Flume

Development of Discharge Prediction Model for Trapezoidal Canals using Simple Portable Flume International Journal of Hydraulic Engineering 01, 1(5): 37-4 OI: 10.593/j.ijhe.010105.0 evelopment of ischarge Prediction Model for Trapezoidal Canals using Simple Portable Flume Avinash M. Badar, Aniruddha.

More information

Pressure Fluctuation around Chute Blocks of SAF Stilling Basins

Pressure Fluctuation around Chute Blocks of SAF Stilling Basins J. Agr. Sci. Tech. (2010) Vol. 12: 203-212 Pressure Fluctuation around Chute Blocks of SAF Stilling Basins J. Farhoudi 1 *, S. M. Sadat-Helbar 1, and N. Aziz 2 ABSTRACT Geometry of the chute blocks in

More information

Analysis of Flow Resistance for Different Bed Materials with Varying Discharge Experimentally in Open Channels

Analysis of Flow Resistance for Different Bed Materials with Varying Discharge Experimentally in Open Channels Analysis of Flow Resistance for Different Bed Materials with Varying Discharge Experimentally in Open Channels Lakshmi Mitra 1, Dr.Mimi Das Saikia 2 M.Tech. Student, Department of Civil Engineering, Assam

More information

We will assume straight channels with simple geometries (prismatic channels) and steady state flow (in time).

We will assume straight channels with simple geometries (prismatic channels) and steady state flow (in time). 56 Review Drag & Lift Laminar vs Turbulent Boundary Layer Turbulent boundary layers stay attached to bodies longer Narrower wake! Lower pressure drag! 8. Open-Channel Flow Pipe/duct flow closed, full,

More information

Numerical simulation of flow in open channels with bottom intake racks

Numerical simulation of flow in open channels with bottom intake racks Water Utility Journal 11: 49-61, 2015. 2015 E.W. Publications Numerical simulation of flow in open channels with bottom intake racks Y.T. Zerihun David & James Engineering and Environmental Consultancy,

More information

Investigation of Flow Profile in Open Channels using CFD

Investigation of Flow Profile in Open Channels using CFD Investigation of Flow Profile in Open Channels using CFD B. K. Gandhi 1, H.K. Verma 2 and Boby Abraham 3 Abstract Accuracy of the efficiency measurement of a hydro-electric generating unit depends on the

More information

New method for discharge hydrograph measurement of the free overflow with full-width, thin-plate weir

New method for discharge hydrograph measurement of the free overflow with full-width, thin-plate weir New method for discharge hydrograph measurement of the free overflow with full-width, thin-plate weir Lajos Hovany* University of Novi Sad, Faculty of Civil Engineering Subotica, Kozaračka, a, 4000, Subotica,

More information

PHYSICAL MODELING FOR SIDE-CHANNEL WEIRS

PHYSICAL MODELING FOR SIDE-CHANNEL WEIRS PHYSICAL MODELING FOR SIDE-CHANNEL WEIRS by Ka-Leung Lee and E. R. Holley Center for Research in Water Resources The University of Texas at Austin Austin, TX 7871 USA CRWR Online Report 0- http://www.crwr.utexas.edu/online.shtml

More information

Flow over oblique Side Weir

Flow over oblique Side Weir Damascus University Journal Vol. (8) - No. () 0 Al-Tali Flow over olique Side Weir Eng. Azza N. Al-Tali * Astract In this paper, an olique side weir was studied y nine models installed at the entrance

More information

OPEN CHANNEL FLOW. Computer Applications. Numerical Methods and. Roland Jeppson. CRC Press UNIVERSITATSB'BUOTHEK TECHNISCHE. INFORMATlONSBiBUOTHEK

OPEN CHANNEL FLOW. Computer Applications. Numerical Methods and. Roland Jeppson. CRC Press UNIVERSITATSB'BUOTHEK TECHNISCHE. INFORMATlONSBiBUOTHEK OPEN CHANNEL FLOW Numerical Methods and Computer Applications Roland Jeppson TECHNISCHE INFORMATlONSBiBUOTHEK UNIVERSITATSB'BUOTHEK HANNOVER Si. i. CRC Press Taylor &.Francis Group Boca Raton London New

More information

Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur

Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Fluid Mechanics Prof. S.K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture - 42 Flows with a Free Surface Part II Good morning. I welcome you to this session

More information

Dr. Muhammad Ali Shamim ; Internal 652

Dr. Muhammad Ali Shamim ; Internal 652 Dr. Muhammad Ali Shamim ali.shamim@uettaxila.edu.pk 051-904765; Internal 65 Channel Tranistions A channel transition is defined as change in channel cross section e.g. change in channel width and/or channel

More information

Local energy losses at positive and negative steps in subcritical open channel flows

Local energy losses at positive and negative steps in subcritical open channel flows Local energ losses at positive and negative steps in subcritical open channel flows Nura Denli Toka and A Burcu Altan-Sakara* Middle East Technical niversit, Department of Civil Engineering, 63, Ankara,

More information

Transactions on Engineering Sciences vol 9, 1996 WIT Press, ISSN

Transactions on Engineering Sciences vol 9, 1996 WIT Press,   ISSN A study of turbulence characteristics in open channel transitions as a function of Froude and Reynolds numbers using Laser technique M.I.A. El-shewey, S.G. Joshi Department of Civil Engineering, Indian

More information

NUMERICAL MODEL FOR MOVABLE BED AS A TOOL FOR THE SIMULATION OF THE RIVER EROSION A CASE STUDY

NUMERICAL MODEL FOR MOVABLE BED AS A TOOL FOR THE SIMULATION OF THE RIVER EROSION A CASE STUDY NUMERICAL MODEL FOR MOVABLE BED AS A TOOL FOR THE SIMULATION OF THE RIVER EROSION A CASE STUDY Solichin 1 Abstract: A serious erosion problem takes place in Cipamingkis River in west Java, Indonesia. As

More information

International Journal of Advance Research, IJOAR.org ISSN

International Journal of Advance Research, IJOAR.org ISSN International Journal of Advance Research, IJOAR.org 1 International Journal of Advance Research, IJOAR.org Volume 1, Issue 9, September 2013, Online: Coefficient Of Discharge For A Compound Weir Combined

More information

Study of Hydraulic Jump Length Coefficient with the Leap Generation by Canal Gate Model

Study of Hydraulic Jump Length Coefficient with the Leap Generation by Canal Gate Model American Journal of Civil Engineering 017; 5(3): 148-154 http://www.sciencepublishinggroup.com/j/ajce doi: 10.11648/j.ajce.0170503.14 ISSN: 330-879 (Print); ISSN: 330-8737 (Online) Study of Hydraulic Jump

More information

New computation method for flood flows and bed variations in a low-lying river with complex river systems

New computation method for flood flows and bed variations in a low-lying river with complex river systems River Flow 2014 Schleiss et al. (Eds) 2014 Taylor & Francis Group, London, ISBN 978-1-138-02674-2 New computation method for flood flows and bed variations in a low-lying river with complex river systems

More information

This is a refereed journal and all articles are professionally screened and reviewed

This is a refereed journal and all articles are professionally screened and reviewed Advances in Environmental Biology, 7(9): 2283-2292, 2013 ISSN 1995-0756 2283 This is a refereed journal and all articles are professionally screened and reviewed ORIGINAL ARTICLE The effects of submerged

More information

Keywords: flow characteristics, compound straight channel, bed morphology, floodplain

Keywords: flow characteristics, compound straight channel, bed morphology, floodplain Flow Characteristics on Floodplain Vegetation in Compound Straight Channels Nur Amirah Nabilah Mohd Zamri 1, a, Zulhilmi Ismail 1,b,Zulkiflee Ibrahim 1,c 1 Faculty of Civil Engineering, Universiti Teknologi

More information

IMPLICIT NUMERICAL SCHEME FOR REGULATING UNSTEADY FLOW IN OPEN CHANNEL Mohamed. T. Shamaa 1, and Hmida M. Karkuri 2

IMPLICIT NUMERICAL SCHEME FOR REGULATING UNSTEADY FLOW IN OPEN CHANNEL Mohamed. T. Shamaa 1, and Hmida M. Karkuri 2 IMPLICIT NUMERICAL SCHEME FOR REGULATING UNSTEADY FLOW IN OPEN CHANNEL Mohamed. T. Shamaa 1, and Hmida M. Karkuri 2 1 Associated Professor, Irrigation and Hydraulic Department, College of Technical Engineering,

More information

CE 6403 APPLIED HYDRAULIC ENGINEERING UNIT - II GRADUALLY VARIED FLOW

CE 6403 APPLIED HYDRAULIC ENGINEERING UNIT - II GRADUALLY VARIED FLOW CE 6403 APPLIED HYDRAULIC ENGINEERING UNIT - II GRADUALLY VARIED FLOW Dynamic equations of gradually varied and spatially varied flows - Water surface flow profile classifications: Hydraulic Slope, Hydraulic

More information

NOTES ON OPEN CHANNEL FLOW

NOTES ON OPEN CHANNEL FLOW NOTES ON OPEN CANNEL FLOW Prof. Marco Pilotti Facoltà di Ingegneria, Università degli Studi di Brescia Profili di moto permanente in un canale e in una serie di due canali - Boudine, 86 OPEN CANNEL FLOW:

More information

Influence of Two-line Emergent Floodplain Vegetation on A Straight Compound Channel Flow

Influence of Two-line Emergent Floodplain Vegetation on A Straight Compound Channel Flow International Journal of Integrated Engineering, Vol. 5 No. 1 (2013) p. 58-63 Influence of Two-line Emergent Floodplain Vegetation on A Straight Compound Channel Flow Mazlin Jumain 1,*, Zulkiflee Ibrahim

More information

Efficiency of an Expansive Transition in an Open Channel Subcritical Flow

Efficiency of an Expansive Transition in an Open Channel Subcritical Flow DUET Journal Vol., Issue, June of an Expansive Transition in an Open Channel Subcritical Flow B. C. Basak and M. Alauddin Department of Civil Engineering Dhaka University of Engineering & Technology, Gazipur,

More information

. ~ S=~aCD=(0.5Ade)/(Ade-1)

. ~ S=~aCD=(0.5Ade)/(Ade-1) JOURNAL OF IRRIGATION AND DRAINAGE ENGINEERING ASCE / NOVEMBER/DECEMBER 2008/883 J Table 1. Relative Sensitivity Index of S1 and S3 Solutions Relative Relative sensitivity sensitivity Ratio of of of SI

More information

Verification on physical model of the erosion downstream of an asymmetrical stream flow

Verification on physical model of the erosion downstream of an asymmetrical stream flow Wasserbaukolloquium 2006: Strömungssimulation im Wasserbau 1 Dresdner Wasserbauliche Mitteilungen Heft 32 Verification on physical model of the erosion downstream of an asymmetrical stream flow G. Ciaravino,

More information

28.2 Classification of Jumps

28.2 Classification of Jumps 28.2 Classification of Jumps As mentioned earlier, the supercritical flow Froude number influences the characteristics of the hydraulic jump. Bradley and Peterka, after extensive experimental investigations,

More information

Uniform Flow in Open Channels

Uniform Flow in Open Channels 1 UNIT 2 Uniform Flow in Open Channels Lecture-01 Introduction & Definition Open-channel flow, a branch of hydraulics, is a type of liquid flow within a conduit with a free surface, known as a channel.

More information