Rail Guide Modular Linear Actuators DSM

Transcription

1 Roller Guide Modular Linear Actuators DLM, DLVM Rail Guide Modular Linear Actuators DSM nookindustries.com toll-free (800)

2 DLM 20, 60, 200 Linear Motor Drive Specifications Function: This unit consists of a rectangular aluminium profile with 2 integrated roller guides. The linear motor DLM unit is based on the principle of a linear, synchronous AC motor. The guiding profile is fitted with permanent magnets as stator (secondary part). The carriage is fitted with the actuator (primary part). The magnetic attraction causes a ce between carriage and guiding profile also in the absence of current. This ce can be used the initial tension of the bearings. Several carriages (primary parts) can be driven independently on one guiding profile. Fitting position: Carriage mounting: Unit mounting: Carriage support: As required. Max. length mm without joints. By T-slots. By T-slots and mounting sets. The linear axis can be combined with any T-slot profile. In the standard version, the carriage runs on 0 or 2 rollers which can be adjusted and serviced at a central servicing position. For longer carriages the number of rollers can be increased. Repeatability ± 0,05 mm. Repeated accuracy max. ± 0,05 bis mm, ± 0, >4.000 mm. Forces and torques Size Forces/Torques dyn Fa (N) Fzm (N) Fy (N) Mx (Nm) My (Nm) Mz (Nm) Mx Fy My Fz Fa Mz Fx Number of rollers All ces and torques related to the following: existing values Fy Fzm Mx My Mz ,5 table values Fy dyn Fzm dyn Mx dyn My dyn Mz dyn Motor specifications Fx Carriage weight (kg),7 2,5 3, 5, 4,7 5,4 9,4 0,5 2,7 Weight primary part (kg) 0,7,4 2,0,4 3,7 5,2 4,5 6,4 8,4 permanent (N) Max. (N) (sek.) Moving ce without current N Speed (m/sec) max Geometrical moments of inertia of aluminium profile lx mm 4 6,6x0 5 22,2x0 5 63,8x0 5 ly mm 4 38,6x0 5 22,0x ,0x0 5 Elastic modulus N/mm² Formula: DLM f = F*L 3 E*I*92 f = deflection F = load (N) L = free length E = elastic modulus (N/mm²) I = second moment of area (mm 4 ) / 2 26 nookindustries.com toll-free (800)

3 DLM 20, 60, 200 Dimensions Increasing the carriage length will increase the basic length by the same amount. *For slide nuts refer to the accessory section V = Q + 00 mm W = servicing position Basic weight Weight per 00 mm Basic length M N O Size A B E H J K P U L /2/3 /2/3 DLM 20 Q M 5 M 6 M ,2/7,2/9,2 Kg,0/,0/,0 Kg DLM 60 Q M 6 M 8 M ,6/5,6/20,7 Kg,6/2,0/2,0 Kg DLM 200 Q M 8 M 0 M ,9/30,5/37,9 Kg 2,6/2,6/2,6 Kg 0 Choice of guide body profile: (0) () (3) without internal profile without internal profile with bellows and cover bands with cover bands (L max. 2000mm) Stainless version upon request. Measurement system () Measurement system LE00 5V (2) Measurement system LE00 24V (3) Hall sensor (4) Measurement system Resolution 0.05 Resolution 0.05 provided by customer Plug () Plug Pos. (2) Plug Pos. 2 (3) open unconnected cable end 500 DLM () with Q (2) 2 with Q 2 (3) 3 with Q 3 (4) Supply with Q * (5) Supply with Q 2 * (6) Supply with Q 3 * Dimensioning criteria motor output * = provided by customer l p b p h ps Q Q 2 Q 3 20 Q Q Q l p = length primary part; b p = width primary part; h ps = height primary part + height secondary part + interspaces primary-/secondary part For standard carriage length see Q in table. For digital controllers and linear encoder refer to chapter page 8. Basic Length + Stroke + Overtravel** = total length **Minimum 25mm on each end Pos Sample ordering code: DLM60, Bahr Modultechnik Linearmotor, standard body profile, Measurement system LE00 5V, Plug Pos., motor size, 54 mm stroke. toll-free (800) nookindustries.com / 3 27

4 DLVM 200 Linear motor drive Specifications Function: This unit consists of a rectangular aluminium profile with 2 integrated roller guides. The linear motor DLVM unit is based on the principle of a linear, synchronous AC motor. The guiding profile is fitted with permanent magnets as stator (secondary part). The carriage is fitted with the actuator (primary part). The magnetic attraction causes a ce between carriage and guiding profile also in the absence of current. This ce can be used the initial tension of the bearings. Several carriages (primary parts) can be driven independently on one guiding profile. Fitting position: Carriage mounting: Unit mounting: Carriage support: As required. Max. length mm without joints. By T-slots. By T-slots and mounting sets. The linear axis can be combined with any T-slot profile. In the standard version, the carriage runs on 8 rollers which can be adjusted and serviced at a central servicing position. For longer carriages the number of rollers can be increased. Repeatability ± 0,05 mm. Repeated accuracy max. ± 0,05 bis mm, ± 0, >4.000 mm. Forces and torques Size Forces/Torques dyn Fa (N) 000 Fzm (N) 3800 Fy (N) 200 Mx (Nm) 220 My (Nm) 230 Mx Fy My Fz Fa Mz Fx Mz (Nm) 20 Number of rollers 2 All ces and torques related to the following: existing values Fy Fzm Mx My Mz ,5 table values Fy dyn Fzm dyn Mx dyn My dyn Mz dyn Motor specifications Fx 3 Carriage weight (kg) 2,7 Weight primary part (kg) 8,4 permanent (N) 766 Max. (N) (sek.) 735 Moving ce without current N 2 Speed (m/sec) max 6 Geometrical moments of inertia of aluminium profile lx mm 4 6,38x0 6 ly mm 4 33,5x0 6 Elastic modulus N/mm² Formula: DLVM f = F*L 3 E*I*92 f = deflection F = load (N) L = free length E = elastic modulus (N/mm²) I = second moment of area (mm 4 ) / 4 28 nookindustries.com toll-free (800)

5 DLVM 200 Dimensions T S Increasing the carriage length will increase the basic length by the same amount. *For slide nuts refer to the accessory section Size Basic length L A B C D E F G H J K M N P Q R S T U Basic weight DLVM ,5 50,5 42,5 5 5,5 54,5 M 8 M M8 98,5 39,4 kg 2,8 kg Weight per 00 mm 500 Basic Length + Stroke + Overtravel** = total length **Minimum 25mm on each end DLVM Pos Sample ordering code: DLVM200, 898 mm stroke. toll-free (800) nookindustries.com / 5 29

6 DSM 20, 60, 200 Linear Motor Drive Specifications Function: This unit consists of a rectangular aluminium profile with 2 integrated rail guidance. The linear motor DSM unit is based on the principle of a linear, synchronous AC motor. The guiding profile is fitted with permanent magnets as stator (secondary part). The carriage is fitted with the actuator (primary part). The magnetic attraction causes a ce between carriage and guiding profile also in the absence of current. This ce can be used the initial tension of the bearings. Several carriages (primary parts) can be driven independently on one guiding profile. Fitting position: As required. Max. length mm without joints. Carriage mounting: By T-slots. Unit mounting: By T-slots and mounting sets. The linear axis can be combined with any T-slot profile. Carriage support: In the standard version, the carriage runs on 4 runner blocks which can be serviced at a central servicing position. For longer carriages the number of runner blocks can be increased. Repeatability ± 0,05mm mm. Repeated accuracy max. ± 0,05mm bis mm, ± 0, >4.000 mm. Forces and torques Size Mx Fy Fz My Fa Mz Fx permitted dyn.forces* 0000 km 0000 km 0000 km Fa (N) Fzm (N) Fz (N) Mx (Nm) My (Nm) MZ (Nm) C (N) Number of runner blocks All ces and torques related to the following: existing values table values Motor specifications Fx Fy + Fzm + Mx + My + Mz,5 Fy dyn Fzm dyn Mx dyn My dyn Mz dyn Carriage weight (kg),4 2,7 4,8 5,3 7, 0,9,4 6,9 Weight primary part (kg) 0,7,4,4 3,7 5,2 4,5 6,4 8,4 permanent (N) Max. (N) sec Moving ce without current N Geometrical moments of inertia of aluminium profile lx mm 4 5,60 x0 5 2,3 x0 6 4,8 x0 6 ly mm 4 34,9 x0 5 2,3 x0 6 26,0 x0 6 Elastic modulus N/mm² Formula: DSM Deflection: Nominal lifetime: * referred to life-time f = F*L 3 L = C E*I*92 ( F ) 3 x0 5 f = deflection C = Dynamic load faktor (N) F = load (N) F = Middle load (N) L = free length E = elastic modulus (N/mm²) I = second moment of area (mm 4 ) / 6 30 nookindustries.com toll-free (800)

7 DSM 20, 60, 200 Dimensions Increasing the carriage length will increase the basic length by the same amount. *For slide nuts refer to the accessory section V = Q + 00 mm W = servicing position Size Basic length L A B E H J K M N O P U Basic weight /2/3 Weight per 00 mm /2/3 DSM 20 Q M 5 M 6 M ,8/6,9 kg,0/,0 DSM 60 Q M 6 M 8 M ,4/6,7/22,6 kg,7/2,0/2,0 kg DSM 200 Q M 8 M 0 M ,0 /33,0 /44,2kg 3,/3,/3, kg 0 Choice of guide body profile: (0) () (3) without internal profile without internal profile with bellows and cover bands with cover bands (L max. 2000mm) Stainless version upon request. Measurement system () Measurement system LE00 5V (2) Measurement system LE00 24V (3) Hall sensor (4) Measurement system Resolution 0.05 Resolution 0.05 provided by customer Plug () Plug Pos. (2) Plug Pos. 2 (3) open unconnected cable end () with Q (2) 2 with Q 2 (3) 3 with Q 3 (4) Supply with Q * (5) Supply with Q 2 * (6) Supply with Q 3 * Dimensioning criteria motor output * = provided by customer l p b p h ps Q Q 2 Q 3 20 Q Q Q DSM Pos l p = length primary part; b p = width primary part; For standard carriage length see Q in table. h The carriages can be delivered in any non-standard ps = height primary part + height secondary part length upon request; the longer the carriage, the + interspaces primary-/secondary part greater the load capacity. For digital controllers and 500 Basic Length + Stroke + Overtravel** = total length linear encoder refer to chapter page 8. **Minimum 25mm on each end Sample ordering code: DSM60, Bahr Modultechnik Linear motor, standard body profile, Measurement system LE00 5V, Plug Pos., motor size, 54 mm stroke toll-free (800) nookindustries.com / 7 3

8 Linear Motor Controller DLM - DSM Modular Linear Actuator Specifications: Linear Encoder LE00 Non-contact sensor unit with integrated analog signal output (sinus Vss). Forming an open linear measuring system if combined with magnetic strip and downstream interpolation electronics. Features: + easy mounting + insensitive to dust, shavings, humidity + signal period 000 µm (analog) + output signals Vss nominal + real-time data processing + used in combination with magnetic strip MB00 + Supply voltage 2-24 V DC +/- 20% / 5V optional 5 V DC +/- 5% + Power consumption approx. 30 ma non-loaded + Protection reverse battery protection + Connection flying leads + Material of casing plastic + Output circuit line driver + Output signals sinusa, B, phase-shifted by 90 + Output current I out max. 5 ma per signal path + Signal size approx. Vss + Travel speed max. 5m/s + System accuracy depending on interpolation electronics + Gap strip/sensor 0, - 0,4 mm (without cover strip) + Working temperature C + Storage temperature C + Interference protection class 3, accord. to ICE 80 + Test mark CE + System of protection IP 67 accord. to DIN VDE 0470 Possible Mounting Styles / 8 32 nookindustries.com toll-free (800)