Moments of inertia of a cross section

Size: px
Start display at page:

Download "Moments of inertia of a cross section"

Transcription

1 BUDAPEST UNVERSTY OF TECHNOLOGY AND ECONOMCS Moments of inertia of a cross section Made by: David Lehotzky Budapest, March 3, 206.

2 Figure : The cross section under study a b h v d Table : Parameters of the cross section in mm Problems Determine the moments of inertia about the horizontal and vertical axes fixed to the centroid of the cross section shown in Figure! 2 Calculate the principal moments of inertia at the centroid of the cross section! 3 Determine the moment of inertia about the zero axis of the cross section for the case when the cross section is loaded by a bending moment M which forms angle β 5 with the horizontal axis! Page/ 0

3 Figure 2: Division of the cross section onto sub cross sections Solution Calculation of the centroid As a first step, the cross section is divided onto parts for which formulas of the moments of inertia are known. One possible division of the cross section is shown in Figure 2. n the following, this particular division is applied.. Area of sub cross sections The sub cross sections shown in Figure 2, have areas A a 2 00 mm 2, A 2 bh 2 6 mm2, A 3 A 2 6 mm 2 A 4 d2 π mm2, A 5 h2 2 8 mm2. The sub cross sections to be subtracted are considered with a minus sign..2 Centroids of sub cross sections The centroids of the different sub cross sections are given by position vectors (see Figure 2). The values of these position vectors in coordinate system (y, z ) are ys a/2 5 r S mm, z S a/2 5 ys2 a + h/3.333 r S2 mm, z S2 b/ ys3 a v h/ r S3 mm, z S3 a v b/ ys4 h 4 r S4 mm, z S4 v + d/2 3 ys5 h/3.333 r S5 z S5 a h/ Page2/ 0

4 Figure 3: Sub cross section.3 Calculation of the centroid The position vector in coordinate system (y, z ), pointing to the centroid of the cross section is r S ys z S 5 i A ir Si 5 i A i A r S + A 2 r S2 + A 3 r S3 + A 4 r S4 + A 5 r S A + A 2 + A 3 + A 4 + A Moments of inertia at the centroids of sub cross sections The moments of inertia have to be calculated about axes y and z (see Figure 2) fixed to the centroid S of the cross section. Fist, one needs to calculate the moments of inertia at the centroids of sub cross sections, then apply the Parallel Axes Theorem to calculate their moments of inertia about axes y and z. Finally, the summation of moments of inertia of sub cross sections gives the moments of inertia of the cross section about axes y and z. 2. Moments of inertia of sub cross sections about axes y and z Sub cross section The st sub cross section is depicted in Figure 3. The moments of inertia of this sub cross section about its own y and z axes, fixed to its centroid are y a mm4, z y mm 4, yz 0. The position vector pointing from centroid S of the sub cross section to centroid S of the cross section in the coordinate system (y, z ) is r SS Y Z ys y S z S z S According to the Parallel Axes Theorem, the moment of inertia of sub cross section about axis y is while its moment of inertia about axis z is,y y + A Z mm 4,,z z + A Y mm 4, Page3/ 0

5 and its product of inertia about axes y and z is Sub cross section 2,yz yz + A Y Z mm 4. The 2 nd sub cross section is depicted in Figure 4. The computations are similar to that of the st sub cross section. The moments of inertia of this sub cross section about its own y 2 and z 2 axes, fixed to its centroid are y2 b3 h mm4, z2 bh mm4, y2z 2 b2 h mm4. The position vector pointing from S 2 to S in coordinate system (y 2, z 2 ) is Y2 ys y r S2S S2 z S z S2 Z Using the Parallel Axes Theorem, the moments of inertia of sub cross section 2 about axes y and z are 2,y y2 + A 2 Z mm 4, 2,z z2 + A 2 Y mm 4, 2,yz y2z 2 + A 2 Y 2 Z mm 4. Figure 4: Sub cross section 2 Figure 5: Sub cross section 3 Sub cross section 3 The 3 rd sub cross section is depicted in Figure 5. The computations are similar to that of the 2 nd sub cross section. However, the moments of inertia about y 3 and z 3 are considered with a minus sign, since sub cross section 3 is to be subtracted. The moments of inertia of this sub cross section about its own y 3 and z 3 axes, fixed to its centroid are y3 b3 h mm4, z3 bh mm4, y3z 3 b2 h mm4. The position vector pointing from S 3 to S in coordinate system (y 3, z 3 ) is Y3 ys y r S3S S3 z S z S3 Z Page4/ 0

6 Note that in contrast with the previous sub cross sections there is a ( ) multiplier in the formula of r S3S. This is due to that y 3 and z 3 axes point in the opposite directions as y and z, respectively. Using the Parallel Axes Theorem, the moments of inertia of sub cross section 3 about axes y and z are 3,y y3 + A 3 Z mm 4, 3,z z3 + A 3 Y mm 4, 3,yz y3z 3 + A 3 Y 3 Z mm 4. t is important to point out that terms due to the Parallel Axes Theorem already consider the minus sign of subtraction within A 3. Sub cross section 4 The 4 th sub cross section is depicted in Figure 6. The computations are similar as before. The moments of inertia of this sub cross section about its own y 4 and z 4 axes, fixed to its centroid are y4 d4 π mm4, z4 y mm 4, y4z 4 0. The position vector pointing from S 4 to S in coordinate system (y 4, z 4 ) is Y4 ys y r S4S S Z 4 z S z S4.26 Using the Parallel Axes Theorem, the moments of inertia of sub cross section 4 about axes y and z are 4,y y4 + A 4 Z mm 4, 4,z z4 + A 4 Y mm 4, 4,yz y4z 4 + A 4 Y 4 Z mm 4. Figure 6: Sub cross section 4 Figure 7: Sub cross section 5 Sub cross section 5 The 5 th sub cross section is depicted in Figure 7. The moments of inertia of this sub cross section about its own y 5 and z 5 axes, fixed to its centroid are y5 h mm4, z5 y5 7. mm 4, y5z 5 h mm4. The position vector pointing from S 5 to S in coordinate system (y 5, z 5 ) is r Y5 y S5S S y S Z 5 (z S z S5 ) 4.45 Axes z 5 and z point in opposite directions, therefore in contrast with the previous sub cross section, the corresponding coordinate of r S5S is multiplied by ( ). Using the Parallel Axes Theorem, the moments of inertia of sub cross section 5 about axes y and z are 5,y y5 + A 5 Z mm 4, 5,z z5 + A 5 Y mm 4, 5,yz y5z 5 + A 5 Y 5 Z mm 4. Page5/ 0

7 2.2 Moments of inertia of the cross section about axes y and z Since all the moments of inertia of sub cross sections are calculated about axes y and z, the moments of inertia of the cross section about axes y and z can be obtained by the summation of corresponding moments of inertia of sub cross sections, thus yz y z 5 i,y,y + 2,y + 3,y + 4,y + 5,y mm 4, i 5 i,z,z + 2,z + 3,z + 4,z + 5,z mm 4, i 5 i,yz,yz + 2,yz + 3,yz + 4,yz + 5,yz mm 4. i Using these results, the matrix of moments of inertia at centroid S, in coordinate system (y, z) is written as y yz mm 4. () (y,z) yz 3 Principle moments of inertia and principle axes z n case of pure bending, the normal stress of beams can be calculated using the Navier formula. When only bending moment M η is acting (rotating about axis η) at the centroid of the cross section, the normal stress is given by σ x (ζ) M η η ζ. (2) n this formula, ζ is an axis perpendicular to η within the plane of the cross section. t is important to note that this formula is valid only when η is a principal moment of inertia, that is product of inertia ηζ is zero. n this case η and ζ are principal axes. Since yz 0, hence y and z are not principal axes. Consequently, in order to apply the Navier formula (2), one has to find the principle directions corresponding to η and ζ. This can be done by the calculation of eigenvalues and eigenvectors of. During the eigenvalue-eigenvector calculation a direction given by vector n is sought, with which the multiplication of matrix is equivalent to the product of a number λ and vector n. That is, a direction n is sought in which the multiplication with matrix behaves exactly as a multiplication with some number λ. Consequently, one is looking for all the pairs of λ and n, which satisfy n λ n. (3) Number λ is called the eigenvalue, while vector n is called the eigenvector of. After rearranging (3), one can have ( λe ) n 0. (4) f n 0 was valid, then no direction could be obtained. Consequently, it follows from (4) that det ( λe ) ( ) det y yz 0 λ yz z 0 y λ yz yz z λ 0 has to hold. After the expansion of the determinant (for the calculation of determinant see the Appendix), one has y λ yz z λ ( y λ)( z λ) yz 2 λ 2 ( y + z ) λ + y z yz 2 0. yz The solutions of this second order equation are λ,2,2 2 ( ) y + z ± ( y z ) 2 + 4yz 2 { mm mm 4. Page6/ 0

8 These eigenvalues give the principle moments of inertia and 2. Eigenvectors n and n 2, corresponding to eigenvalues λ and λ 2, respectively, can be calculated by the substitution of eigenvalues in (4). After the substitution of λ, one has y λ yz n 0. (5) yz z λ n 2 0 }{{} n The expansion of the matrix-vector product (for details see the Appendix) gives equations ( y λ ) n yz n 2 0, (6) yz n + ( z λ ) n 2 0. (7) Here coordinates n and n 2 of vector n are unknowns. However, equations (6)-(7) are not independent from each other, since det( λ E) 0. Consequently, one out of the two unknown coordinates of n can be chosen arbitrarily. Let n be chosen. n this case (6) gives which implies n 2 y λ yz n y λ yz, n y λ yz.456 Similarly, the substitution of λ 2 to (4), gives yz z λ 2 n 22 y λ 2 yz n2 which, after setting n 2, implies n 2 y λ 2 yz } {{ } n , (8) Note that the length of eigenvectors n and n 2 can be changed by modifying the arbitrarily chosen coordinates n and n 2, respectively. t is useful to give the eigenvectors as unit vectors. This can be done by the norming of n and n 2. The normed eigenvectors are m m 2 m m2 m 2 m 22 n n n 2 + n 2 2 n 2 n 2 n n 2 22 n n2 n 2 n The principal axes ζ and η are assigned by the normed eigenvectors m and m 2, respectively (see Figure 8). Consequently, the moments of inertia about these axes are ζ and η 2. t is important to note that depending on how n and n 2 were chosen in (5) and (8), vectors m and m 2 could point in the opposite direction as well. These results would be also correct.,. 4 Moment of inertia about the zero axis The bending moment M acting in the cross section can be decomposed onto coordinates M η and M ζ in the coordinate system of the principle axes (see Figure 8). By assuming that only bending moment M η acts in the cross section (see Figure 9), the normal stress can be calculated according to (2). With the assumption that only bending moment M ζ acts in the cross section (see Figure 0) the normal stress is determined by σ x (η) M ζ ζ ( η). (9) Page7/ 0

9 Figure 8: The principal axes of the cross section shown by blue color and the zero axis shown by green color Here coordinate η has a ( ) multiplier since normal stress σ x is positive for negative η coordinates. When both M η and M ζ act in the cross section, the normal stress is the sum of (2) and (9), that is σ x (η, ζ) M η η ζ M ζ ζ η. (0) The zero axis consists of points in the cross section where the normal stress is zero, that is where σ x (η, ζ) 0. Based on Figure 8 ( ( ) ) m 22 M η M cos(α + δ + β) M cos atan + β M, and using (0), the zeros axis is given by the line m 2 M ζ M sin(α + δ + β) M, ζ M ζ η M η ζ η tan(α + β + δ) η ζ 0.93 η. The slope of the line is characterized by the angle (see Figure 8) ( α atan tan(α + β + δ) ) η ζ Page8/ 0

10 Figure 9: Cross section parts under tension (red) and compression (green) in the case when only M η acts in the cross section Figure 0: Cross section parts under tension (red) and compression (green) in the case when only M ζ acts in the cross section The matrix () of moments of inertia is given in coordinate system (y, z). Using matrix M, the matrix of moments of inertia can be transformed in the coordinate system (η, ζ) of principle directions as where matrix M m2 m M (y,z) M, () m2 m m 22 m describes the transformation from coordinate system (y, z) to the coordinate system (η, ζ) assigned by m and m 2. Details on the computation of the inverse A of a matrix A can be found in the Appendix. Due to that M is always symmetric, its inversion is simplified as M M T, that is the inverse of M is equivalent to its transpose. Details on the computation of the transpose A T of a matrix A can be found in the Appendix. The substitution to () gives η ηζ ηζ ζ mm 4, that is ηζ 0 is obtained. t can be shown that this follows from (3) in case of any. n general, the transformation from coordinate system (η, ζ) to coordinate system (η, ζ ) can be described by the matrix e2 e T e2 e, e 22 e 2 where vectors e 2 and e assign the direction of coordinates (η, ζ ) in coordinate system (η, ζ). Consequently, any vector given in (η, ζ) can be transformed to (η, ζ ) as r (η,ζ ) T r. The above transformation can be applied for the matrix of moments of inertia as (η,ζ ) T T. (2) Based on Figure 8, coordinate system (η, ζ ) assigned by the zero axis is given by unit vectors cos(α) sin(α) 0.90 e 2, e sin(α) 0.90 cos(α) in coordinate system (η, ζ). Since unit vectors e and e 2 are perpendicular to each other T T T. After substitution, (2) gives η η ζ η ζ mm 4. ζ (η,ζ ) Page9/ 0

11 Consequently, the moment of inertia about the zero axis is Matrix (η,ζ ) η mm 4. can be also determined by a transformation matrix defined in coordinate system (y, z). Based on Figure 8 ( ) m 22 δ atan α n coordinate system (y, z), the coordinate system (η, ζ ) can be assigned by unit vectors cos(δ) 0.97 sin(δ) e 2, e sin(δ) cos(δ) 0.97 (y,z) (y,z) m 2. These unit vectors are again perpendicular to each other thus T T T cos(δ) sin(δ) y sin(δ) cos(δ) (η,ζ ) (y,z) (y,z) (y,z) yz yz z cos(δ) sin(δ) sin(δ) cos(δ) mm 4. Appendix Some basic manipulations of 2 2 matrices a a A 2 b b, B 2 a 2 a 22 b 2 b 22, d d d 2 Transpose A T a a 2 a 2 a 22 Multiplication A d C A B a d + a 2 d 2 a 2 d + a 22 d 2 c c 2 c 2 c 22 c a b + a 2 b 2, c 2 a b 2 + a 2 b 22 c 2 a 2 b + a 22 b 2, c a 2 b 2 + a 22 b 22 Determinant nverse A det(a) adj ( A ) det(a) a a 22 a 2 a 2 a a 22 a 2 a 2 a22 a 2 a 2 a Page0/ 0

Hong Kong Institute of Vocational Education (Tsing Yi) Higher Diploma in Civil Engineering Structural Mechanics. Chapter 2 SECTION PROPERTIES

Hong Kong Institute of Vocational Education (Tsing Yi) Higher Diploma in Civil Engineering Structural Mechanics. Chapter 2 SECTION PROPERTIES Section Properties Centroid The centroid of an area is the point about which the area could be balanced if it was supported from that point. The word is derived from the word center, and it can be though

More information

h p://edugen.wileyplus.com/edugen/courses/crs1404/pc/b03/c2hlch...

h p://edugen.wileyplus.com/edugen/courses/crs1404/pc/b03/c2hlch... n this appendix we discuss... 1 of 4 16-Sep-12 19:35 APPENDIX C In this appendix we discuss how to calculate the moment of inertia of an area. 1 The moment of inertia of an area was first introduced in

More information

6. Bending CHAPTER OBJECTIVES

6. Bending CHAPTER OBJECTIVES CHAPTER OBJECTIVES Determine stress in members caused by bending Discuss how to establish shear and moment diagrams for a beam or shaft Determine largest shear and moment in a member, and specify where

More information

4. BEAMS: CURVED, COMPOSITE, UNSYMMETRICAL

4. BEAMS: CURVED, COMPOSITE, UNSYMMETRICAL 4. BEMS: CURVED, COMPOSITE, UNSYMMETRICL Discussions of beams in bending are usually limited to beams with at least one longitudinal plane of symmetry with the load applied in the plane of symmetry or

More information

Chapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd

Chapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd Chapter Objectives To generalize the procedure by formulating equations that can be plotted so that they describe the internal shear and moment throughout a member. To use the relations between distributed

More information

SOLUTION KEY TO THE LINEAR ALGEBRA FINAL EXAM 1 2 ( 2) ( 1) c a = 1 0

SOLUTION KEY TO THE LINEAR ALGEBRA FINAL EXAM 1 2 ( 2) ( 1) c a = 1 0 SOLUTION KEY TO THE LINEAR ALGEBRA FINAL EXAM () We find a least squares solution to ( ) ( ) A x = y or 0 0 a b = c 4 0 0. 0 The normal equation is A T A x = A T y = y or 5 0 0 0 0 0 a b = 5 9. 0 0 4 7

More information

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST

More information

Stress Analysis Lecture 4 ME 276 Spring Dr./ Ahmed Mohamed Nagib Elmekawy

Stress Analysis Lecture 4 ME 276 Spring Dr./ Ahmed Mohamed Nagib Elmekawy Stress Analysis Lecture 4 ME 76 Spring 017-018 Dr./ Ahmed Mohamed Nagib Elmekawy Shear and Moment Diagrams Beam Sign Convention The positive directions are as follows: The internal shear force causes a

More information

AREAS, RADIUS OF GYRATION

AREAS, RADIUS OF GYRATION Chapter 10 MOMENTS of INERTIA for AREAS, RADIUS OF GYRATION Today s Objectives: Students will be able to: a) Define the moments of inertia (MoI) for an area. b) Determine the MoI for an area by integration.

More information

Statics: Lecture Notes for Sections

Statics: Lecture Notes for Sections 0.5 MOMENT OF INERTIA FOR A COMPOSITE AREA A composite area is made by adding or subtracting a series of simple shaped areas like rectangles, triangles, and circles. For example, the area on the left can

More information

Statics: Lecture Notes for Sections 10.1,10.2,10.3 1

Statics: Lecture Notes for Sections 10.1,10.2,10.3 1 Chapter 10 MOMENTS of INERTIA for AREAS, RADIUS OF GYRATION Today s Objectives: Students will be able to: a) Define the moments of inertia (MoI) for an area. b) Determine the MoI for an area by integration.

More information

10.5 MOMENT OF INERTIA FOR A COMPOSITE AREA

10.5 MOMENT OF INERTIA FOR A COMPOSITE AREA 10.5 MOMENT OF NERTA FOR A COMPOSTE AREA A composite area is made by adding or subtracting a series of simple shaped areas like rectangles, triangles, and circles. For example, the area on the left can

More information

Chapter 9 Moment of Inertia

Chapter 9 Moment of Inertia Chapter 9 Moment of Inertia Dr. Khairul Salleh Basaruddin Applied Mechanics Division School of Mechatronic Engineering Universiti Malaysia Perlis (UniMAP) khsalleh@unimap.edu.my PARALLEL-AXIS THEOREM,

More information

CH. 4 BEAMS & COLUMNS

CH. 4 BEAMS & COLUMNS CH. 4 BEAMS & COLUMNS BEAMS Beams Basic theory of bending: internal resisting moment at any point in a beam must equal the bending moments produced by the external loads on the beam Rx = Cc + Tt - If the

More information

Principal Components Analysis (PCA)

Principal Components Analysis (PCA) Principal Components Analysis (PCA) Principal Components Analysis (PCA) a technique for finding patterns in data of high dimension Outline:. Eigenvectors and eigenvalues. PCA: a) Getting the data b) Centering

More information

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC.

PURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC. BENDING STRESS The effect of a bending moment applied to a cross-section of a beam is to induce a state of stress across that section. These stresses are known as bending stresses and they act normally

More information

Advanced Strength of Materials Prof. S. K. Maiti Department of Mechanical Engineering Indian Institute of Technology, Bombay.

Advanced Strength of Materials Prof. S. K. Maiti Department of Mechanical Engineering Indian Institute of Technology, Bombay. Advanced Strength of Materials Prof. S. K. Maiti Department of Mechanical Engineering Indian Institute of Technology, Bombay Lecture 32 Today we will talk about un symmetric bending. We have already studied

More information

Classical Mechanics. Luis Anchordoqui

Classical Mechanics. Luis Anchordoqui 1 Rigid Body Motion Inertia Tensor Rotational Kinetic Energy Principal Axes of Rotation Steiner s Theorem Euler s Equations for a Rigid Body Eulerian Angles Review of Fundamental Equations 2 Rigid body

More information

Properties of Sections

Properties of Sections ARCH 314 Structures I Test Primer Questions Dr.-Ing. Peter von Buelow Properties of Sections 1. Select all that apply to the characteristics of the Center of Gravity: A) 1. The point about which the body

More information

ME 201 Engineering Mechanics: Statics

ME 201 Engineering Mechanics: Statics ME 0 Engineering Mechanics: Statics Unit 9. Moments of nertia Definition of Moments of nertia for Areas Parallel-Axis Theorem for an Area Radius of Gyration of an Area Moments of nertia for Composite Areas

More information

Bending Stress. Sign convention. Centroid of an area

Bending Stress. Sign convention. Centroid of an area Bending Stress Sign convention The positive shear force and bending moments are as shown in the figure. Centroid of an area Figure 40: Sign convention followed. If the area can be divided into n parts

More information

(Refer Slide Time: 2:43-03:02)

(Refer Slide Time: 2:43-03:02) Strength of Materials Prof. S. K. Bhattacharyya Department of Civil Engineering Indian Institute of Technology, Kharagpur Lecture - 34 Combined Stresses I Welcome to the first lesson of the eighth module

More information

Review of Linear Algebra

Review of Linear Algebra Review of Linear Algebra Definitions An m n (read "m by n") matrix, is a rectangular array of entries, where m is the number of rows and n the number of columns. 2 Definitions (Con t) A is square if m=

More information

Chapter 9 BIAXIAL SHEARING

Chapter 9 BIAXIAL SHEARING 9. DEFNTON Chapter 9 BAXAL SHEARNG As we have seen in the previous chapter, biaial (oblique) shearing produced b the shear forces and, appears in a bar onl accompanied b biaial bending (we ma discuss about

More information

SIGN CONVENTION OF STRESS RESULTANTS

SIGN CONVENTION OF STRESS RESULTANTS SIGN CONVENTION OF STRESS RESULTANTS A quick guide to understanding the sign conventions used in the ush Me ull Me models National HE STEM rogramme INTRODUCTION Representing stress resultants graphically

More information

UNSYMMETRICAL BENDING

UNSYMMETRICAL BENDING UNSYMMETRICAL BENDING The general bending stress equation for elastic, homogeneous beams is given as (II.1) where Mx and My are the bending moments about the x and y centroidal axes, respectively. Ix and

More information

Second Moments or Moments of Inertia

Second Moments or Moments of Inertia Second Moments or Moments of Inertia The second moment of inertia of an element of area such as da in Figure 1 with respect to any axis is defined as the product of the area of the element and the square

More information

Lecture 15 Strain and stress in beams

Lecture 15 Strain and stress in beams Spring, 2019 ME 323 Mechanics of Materials Lecture 15 Strain and stress in beams Reading assignment: 6.1 6.2 News: Instructor: Prof. Marcial Gonzalez Last modified: 1/6/19 9:42:38 PM Beam theory (@ ME

More information

Conceptual Questions for Review

Conceptual Questions for Review Conceptual Questions for Review Chapter 1 1.1 Which vectors are linear combinations of v = (3, 1) and w = (4, 3)? 1.2 Compare the dot product of v = (3, 1) and w = (4, 3) to the product of their lengths.

More information

[8] Bending and Shear Loading of Beams

[8] Bending and Shear Loading of Beams [8] Bending and Shear Loading of Beams Page 1 of 28 [8] Bending and Shear Loading of Beams [8.1] Bending of Beams (will not be covered in class) [8.2] Bending Strain and Stress [8.3] Shear in Straight

More information

7 TRANSVERSE SHEAR transverse shear stress longitudinal shear stresses

7 TRANSVERSE SHEAR transverse shear stress longitudinal shear stresses 7 TRANSVERSE SHEAR Before we develop a relationship that describes the shear-stress distribution over the cross section of a beam, we will make some preliminary remarks regarding the way shear acts within

More information

M.A.P. Matrix Algebra Procedures. by Mary Donovan, Adrienne Copeland, & Patrick Curry

M.A.P. Matrix Algebra Procedures. by Mary Donovan, Adrienne Copeland, & Patrick Curry M.A.P. Matrix Algebra Procedures by Mary Donovan, Adrienne Copeland, & Patrick Curry This document provides an easy to follow background and review of basic matrix definitions and algebra. Because population

More information

Chapter 8 BIAXIAL BENDING

Chapter 8 BIAXIAL BENDING Chapter 8 BAXAL BENDN 8.1 DEFNTON A cross section is subjected to biaial (oblique) bending if the normal (direct) stresses from section are reduced to two bending moments and. enerall oblique bending is

More information

Chapter 10: Moments of Inertia

Chapter 10: Moments of Inertia Chapter 10: Moments of Inertia Chapter Objectives To develop a method for determining the moment of inertia and product of inertia for an area with respect to given x- and y-axes. To develop a method for

More information

A = 3 B = A 1 1 matrix is the same as a number or scalar, 3 = [3].

A = 3 B = A 1 1 matrix is the same as a number or scalar, 3 = [3]. Appendix : A Very Brief Linear ALgebra Review Introduction Linear Algebra, also known as matrix theory, is an important element of all branches of mathematics Very often in this course we study the shapes

More information

DEFINITION OF MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA

DEFINITION OF MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA DEFINITION OF MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA Today s Objectives: Students will be able to: a) Define the moments of inertia (MoI) for an area. b) Determine the moment of inertia

More information

235 Final exam review questions

235 Final exam review questions 5 Final exam review questions Paul Hacking December 4, 0 () Let A be an n n matrix and T : R n R n, T (x) = Ax the linear transformation with matrix A. What does it mean to say that a vector v R n is an

More information

Samantha Ramirez, MSE

Samantha Ramirez, MSE Samantha Ramirez, MSE Centroids The centroid of an area refers to the point that defines the geometric center for the area. In cases where the area has an axis of symmetry, the centroid will lie along

More information

Chapter. Algebra techniques. Syllabus Content A Basic Mathematics 10% Basic algebraic techniques and the solution of equations.

Chapter. Algebra techniques. Syllabus Content A Basic Mathematics 10% Basic algebraic techniques and the solution of equations. Chapter 2 Algebra techniques Syllabus Content A Basic Mathematics 10% Basic algebraic techniques and the solution of equations. Page 1 2.1 What is algebra? In order to extend the usefulness of mathematical

More information

This procedure covers the determination of the moment of inertia about the neutral axis.

This procedure covers the determination of the moment of inertia about the neutral axis. 327 Sample Problems Problem 16.1 The moment of inertia about the neutral axis for the T-beam shown is most nearly (A) 36 in 4 (C) 236 in 4 (B) 136 in 4 (D) 736 in 4 This procedure covers the determination

More information

Math 302 Outcome Statements Winter 2013

Math 302 Outcome Statements Winter 2013 Math 302 Outcome Statements Winter 2013 1 Rectangular Space Coordinates; Vectors in the Three-Dimensional Space (a) Cartesian coordinates of a point (b) sphere (c) symmetry about a point, a line, and a

More information

Equilibrium of Deformable Body

Equilibrium of Deformable Body Equilibrium of Deformable Body Review Static Equilibrium If a body is in static equilibrium under the action applied external forces, the Newton s Second Law provides us six scalar equations of equilibrium

More information

22.3. Repeated Eigenvalues and Symmetric Matrices. Introduction. Prerequisites. Learning Outcomes

22.3. Repeated Eigenvalues and Symmetric Matrices. Introduction. Prerequisites. Learning Outcomes Repeated Eigenvalues and Symmetric Matrices. Introduction In this Section we further develop the theory of eigenvalues and eigenvectors in two distinct directions. Firstly we look at matrices where one

More information

CHAPTER -6- BENDING Part -1-

CHAPTER -6- BENDING Part -1- Ishik University / Sulaimani Civil Engineering Department Mechanics of Materials CE 211 CHAPTER -6- BENDING Part -1-1 CHAPTER -6- Bending Outlines of this chapter: 6.1. Chapter Objectives 6.2. Shear and

More information

Lecture 3 The Concept of Stress, Generalized Stresses and Equilibrium

Lecture 3 The Concept of Stress, Generalized Stresses and Equilibrium Lecture 3 The Concept of Stress, Generalized Stresses and Equilibrium Problem 3-1: Cauchy s Stress Theorem Cauchy s stress theorem states that in a stress tensor field there is a traction vector t that

More information

The minus sign indicates that the centroid is located below point E. We will relocate the axis as shown in Figure (1) and take discard the sign:

The minus sign indicates that the centroid is located below point E. We will relocate the axis as shown in Figure (1) and take discard the sign: AOE 304: Thin Walled Structures Solutions to Consider a cantilever beam as shown in the attached figure. At the tip of the beam, a bending moment M = 1000 N-m is applied at an angle θ with respect to the

More information

Repeated Eigenvalues and Symmetric Matrices

Repeated Eigenvalues and Symmetric Matrices Repeated Eigenvalues and Symmetric Matrices. Introduction In this Section we further develop the theory of eigenvalues and eigenvectors in two distinct directions. Firstly we look at matrices where one

More information

Lecture Pure Twist

Lecture Pure Twist Lecture 4-2003 Pure Twist pure twist around center of rotation D => neither axial (σ) nor bending forces (Mx, My) act on section; as previously, D is fixed, but (for now) arbitrary point. as before: a)

More information

Strength of Materials II (Mechanics of Materials) (SI Units) Dr. Ashraf Alfeehan

Strength of Materials II (Mechanics of Materials) (SI Units) Dr. Ashraf Alfeehan Strength of Materials II (Mechanics of Materials) (SI Units) Dr. Ashraf Alfeehan 2017-2018 Mechanics of Material II Text Books Mechanics of Materials, 10th edition (SI version), by: R. C. Hibbeler, 2017

More information

Advanced Structural Analysis EGF Section Properties and Bending

Advanced Structural Analysis EGF Section Properties and Bending Advanced Structural Analysis EGF316 3. Section Properties and Bending 3.1 Loads in beams When we analyse beams, we need to consider various types of loads acting on them, for example, axial forces, shear

More information

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics

PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics Page1 PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [2910601] Introduction, Fundamentals of Statics 1. Differentiate between Scalar and Vector quantity. Write S.I.

More information

Chapter 2 Notes, Linear Algebra 5e Lay

Chapter 2 Notes, Linear Algebra 5e Lay Contents.1 Operations with Matrices..................................1.1 Addition and Subtraction.............................1. Multiplication by a scalar............................ 3.1.3 Multiplication

More information

Chapter (7) Lateral Earth Pressure

Chapter (7) Lateral Earth Pressure Chapter (7) Lateral Earth Pressure Introduction Vertical or near vertical slopes of soil are supported by retaining walls, cantilever sheet-pile walls, sheet-pile bulkheads, braced cuts, and other similar

More information

(Refer Slide Time: 01:00 01:01)

(Refer Slide Time: 01:00 01:01) Strength of Materials Prof: S.K.Bhattacharya Department of Civil Engineering Indian institute of Technology Kharagpur Lecture no 27 Lecture Title: Stresses in Beams- II Welcome to the second lesson of

More information

Supplement: Statically Indeterminate Frames

Supplement: Statically Indeterminate Frames : Statically Indeterminate Frames Approximate Analysis - In this supplement, we consider another approximate method of solving statically indeterminate frames subjected to lateral loads known as the. Like

More information

Appendix A: Matrices

Appendix A: Matrices Appendix A: Matrices A matrix is a rectangular array of numbers Such arrays have rows and columns The numbers of rows and columns are referred to as the dimensions of a matrix A matrix with, say, 5 rows

More information

STEP Support Programme. STEP 2 Matrices Topic Notes

STEP Support Programme. STEP 2 Matrices Topic Notes STEP Support Programme STEP 2 Matrices Topic Notes Definitions............................................. 2 Manipulating Matrices...................................... 3 Transformations.........................................

More information

REVOLVED CIRCLE SECTIONS. Triangle revolved about its Centroid

REVOLVED CIRCLE SECTIONS. Triangle revolved about its Centroid REVOLVED CIRCLE SECTIONS Triangle revolved about its Centroid Box-in Method Circle Sector Method Integrating to solve I, Ax, and A for a revolved triangle is difficult. A quadrilateral and another triangle

More information

CHAPTER 4: BENDING OF BEAMS

CHAPTER 4: BENDING OF BEAMS (74) CHAPTER 4: BENDING OF BEAMS This chapter will be devoted to the analysis of prismatic members subjected to equal and opposite couples M and M' acting in the same longitudinal plane. Such members are

More information

, some directions, namely, the directions of the 1. and

, some directions, namely, the directions of the 1. and 11. Eigenvalues and eigenvectors We have seen in the last chapter: for the centroaffine mapping, some directions, namely, the directions of the 1 coordinate axes: and 0 0, are distinguished 1 among all

More information

Chapter (6) Geometric Design of Shallow Foundations

Chapter (6) Geometric Design of Shallow Foundations Chapter (6) Geometric Design of Shallow Foundations Introduction As we stated in Chapter 3, foundations are considered to be shallow if if [D (3 4)B]. Shallow foundations have several advantages: minimum

More information

The Laplace Expansion Theorem: Computing the Determinants and Inverses of Matrices

The Laplace Expansion Theorem: Computing the Determinants and Inverses of Matrices The Laplace Expansion Theorem: Computing the Determinants and Inverses of Matrices David Eberly, Geometric Tools, Redmond WA 98052 https://www.geometrictools.com/ This work is licensed under the Creative

More information

Chapter 6: Cross-Sectional Properties of Structural Members

Chapter 6: Cross-Sectional Properties of Structural Members Chapter 6: Cross-Sectional Properties of Structural Members Introduction Beam design requires the knowledge of the following. Material strengths (allowable stresses) Critical shear and moment values Cross

More information

Steel Post Load Analysis

Steel Post Load Analysis Steel Post Load Analysis Scope The steel posts in 73019022, 73019024, and 73019025, are considered to be traditional building products. According to the 2015 International Building Code, this type of product

More information

CH. 5 TRUSSES BASIC PRINCIPLES TRUSS ANALYSIS. Typical depth-to-span ratios range from 1:10 to 1:20. First: determine loads in various members

CH. 5 TRUSSES BASIC PRINCIPLES TRUSS ANALYSIS. Typical depth-to-span ratios range from 1:10 to 1:20. First: determine loads in various members CH. 5 TRUSSES BASIC PRINCIPLES Typical depth-to-span ratios range from 1:10 to 1:20 - Flat trusses require less overall depth than pitched trusses Spans: 40-200 Spacing: 10 to 40 on center - Residential

More information

1 Matrices and vector spaces

1 Matrices and vector spaces Matrices and vector spaces. Which of the following statements about linear vector spaces are true? Where a statement is false, give a counter-example to demonstrate this. (a) Non-singular N N matrices

More information

A VERY BRIEF LINEAR ALGEBRA REVIEW for MAP 5485 Introduction to Mathematical Biophysics Fall 2010

A VERY BRIEF LINEAR ALGEBRA REVIEW for MAP 5485 Introduction to Mathematical Biophysics Fall 2010 A VERY BRIEF LINEAR ALGEBRA REVIEW for MAP 5485 Introduction to Mathematical Biophysics Fall 00 Introduction Linear Algebra, also known as matrix theory, is an important element of all branches of mathematics

More information

Matrices. A matrix is a method of writing a set of numbers using rows and columns. Cells in a matrix can be referenced in the form.

Matrices. A matrix is a method of writing a set of numbers using rows and columns. Cells in a matrix can be referenced in the form. Matrices A matrix is a method of writing a set of numbers using rows and columns. 1 2 3 4 3 2 1 5 7 2 5 4 2 0 5 10 12 8 4 9 25 30 1 1 Reading Information from a Matrix Cells in a matrix can be referenced

More information

Strength of Materials Prof. S.K.Bhattacharya Dept. of Civil Engineering, I.I.T., Kharagpur Lecture No.26 Stresses in Beams-I

Strength of Materials Prof. S.K.Bhattacharya Dept. of Civil Engineering, I.I.T., Kharagpur Lecture No.26 Stresses in Beams-I Strength of Materials Prof. S.K.Bhattacharya Dept. of Civil Engineering, I.I.T., Kharagpur Lecture No.26 Stresses in Beams-I Welcome to the first lesson of the 6th module which is on Stresses in Beams

More information

MECHANICS OF MATERIALS. Analysis of Beams for Bending

MECHANICS OF MATERIALS. Analysis of Beams for Bending MECHANICS OF MATERIALS Analysis of Beams for Bending By NUR FARHAYU ARIFFIN Faculty of Civil Engineering & Earth Resources Chapter Description Expected Outcomes Define the elastic deformation of an axially

More information

Multivariate Statistics Fundamentals Part 1: Rotation-based Techniques

Multivariate Statistics Fundamentals Part 1: Rotation-based Techniques Multivariate Statistics Fundamentals Part 1: Rotation-based Techniques A reminded from a univariate statistics courses Population Class of things (What you want to learn about) Sample group representing

More information

Consider a cross section with a general shape such as shown in Figure B.2.1 with the x axis normal to the cross section. Figure B.2.1.

Consider a cross section with a general shape such as shown in Figure B.2.1 with the x axis normal to the cross section. Figure B.2.1. ppendix B rea Properties of Cross Sections B.1 Introduction The area, the centroid of area, and the area moments of inertia of the cross sections are needed in slender bar calculations for stress and deflection.

More information

MATRICES The numbers or letters in any given matrix are called its entries or elements

MATRICES The numbers or letters in any given matrix are called its entries or elements MATRICES A matrix is defined as a rectangular array of numbers. Examples are: 1 2 4 a b 1 4 5 A : B : C 0 1 3 c b 1 6 2 2 5 8 The numbers or letters in any given matrix are called its entries or elements

More information

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 4 Pure Bending Homework Answers

EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 4 Pure Bending Homework Answers EA 3702 echanics & aterials Science (echanics of aterials) Chapter 4 Pure Bending Homework Answers 100 mm Homework 4.1 For pure bending moment of 5 kn m on hollow beam with uniform wall thickness of 10

More information

Chapter 4 Analysis of a cantilever

Chapter 4 Analysis of a cantilever Chapter 4 Analysis of a cantilever Before a complex structure is studied performing a seismic analysis, the behaviour of simpler ones should be fully understood. To achieve this knowledge we will start

More information

MTE 119 STATICS FINAL HELP SESSION REVIEW PROBLEMS PAGE 1 9 NAME & ID DATE. Example Problem P.1

MTE 119 STATICS FINAL HELP SESSION REVIEW PROBLEMS PAGE 1 9 NAME & ID DATE. Example Problem P.1 MTE STATICS Example Problem P. Beer & Johnston, 004 by Mc Graw-Hill Companies, Inc. The structure shown consists of a beam of rectangular cross section (4in width, 8in height. (a Draw the shear and bending

More information

Eigenvalues and Eigenvectors. Review: Invertibility. Eigenvalues and Eigenvectors. The Finite Dimensional Case. January 18, 2018

Eigenvalues and Eigenvectors. Review: Invertibility. Eigenvalues and Eigenvectors. The Finite Dimensional Case. January 18, 2018 January 18, 2018 Contents 1 2 3 4 Review 1 We looked at general determinant functions proved that they are all multiples of a special one, called det f (A) = f (I n ) det A. Review 1 We looked at general

More information

and let s calculate the image of some vectors under the transformation T.

and let s calculate the image of some vectors under the transformation T. Chapter 5 Eigenvalues and Eigenvectors 5. Eigenvalues and Eigenvectors Let T : R n R n be a linear transformation. Then T can be represented by a matrix (the standard matrix), and we can write T ( v) =

More information

1. Background. is usually significantly lower than it is in uniaxial tension

1. Background. is usually significantly lower than it is in uniaxial tension NOTES ON QUANTIFYING MODES OF A SECOND- ORDER TENSOR. The mechanical behavior of rocks and rock-like materials (concrete, ceramics, etc.) strongly depends on the loading mode, defined by the values and

More information

Assignment 11 (C + C ) = (C + C ) = (C + C) i(c C ) ] = i(c C) (AB) = (AB) = B A = BA 0 = [A, B] = [A, B] = (AB BA) = (AB) AB

Assignment 11 (C + C ) = (C + C ) = (C + C) i(c C ) ] = i(c C) (AB) = (AB) = B A = BA 0 = [A, B] = [A, B] = (AB BA) = (AB) AB Arfken 3.4.6 Matrix C is not Hermition. But which is Hermitian. Likewise, Assignment 11 (C + C ) = (C + C ) = (C + C) [ i(c C ) ] = i(c C ) = i(c C) = i ( C C ) Arfken 3.4.9 The matrices A and B are both

More information

(Mathematical Operations with Arrays) Applied Linear Algebra in Geoscience Using MATLAB

(Mathematical Operations with Arrays) Applied Linear Algebra in Geoscience Using MATLAB Applied Linear Algebra in Geoscience Using MATLAB (Mathematical Operations with Arrays) Contents Getting Started Matrices Creating Arrays Linear equations Mathematical Operations with Arrays Using Script

More information

Beams III -- Shear Stress: 1

Beams III -- Shear Stress: 1 Beams III -- Shear Stress: 1 Internal Shear Force Shear Stress Formula for Beams The First Area Moment, Q Shear Stresses in Beam Flanges Shear Distribution on an I Beam 1 2 In this stack we will derive

More information

(b) If a multiple of one row of A is added to another row to produce B then det(b) =det(a).

(b) If a multiple of one row of A is added to another row to produce B then det(b) =det(a). .(5pts) Let B = 5 5. Compute det(b). (a) (b) (c) 6 (d) (e) 6.(5pts) Determine which statement is not always true for n n matrices A and B. (a) If two rows of A are interchanged to produce B, then det(b)

More information

BOOK OF COURSE WORKS ON STRENGTH OF MATERIALS FOR THE 2 ND YEAR STUDENTS OF THE UACEG

BOOK OF COURSE WORKS ON STRENGTH OF MATERIALS FOR THE 2 ND YEAR STUDENTS OF THE UACEG BOOK OF COURSE WORKS ON STRENGTH OF MATERIALS FOR THE ND YEAR STUDENTS OF THE UACEG Assoc.Prof. Dr. Svetlana Lilkova-Markova, Chief. Assist. Prof. Dimitar Lolov Sofia, 011 STRENGTH OF MATERIALS GENERAL

More information

19. Principal Stresses

19. Principal Stresses 19. Principal Stresses I Main Topics A Cauchy s formula B Principal stresses (eigenvectors and eigenvalues) C Example 10/24/18 GG303 1 19. Principal Stresses hkp://hvo.wr.usgs.gov/kilauea/update/images.html

More information

UNIT- I Thin plate theory, Structural Instability:

UNIT- I Thin plate theory, Structural Instability: UNIT- I Thin plate theory, Structural Instability: Analysis of thin rectangular plates subject to bending, twisting, distributed transverse load, combined bending and in-plane loading Thin plates having

More information

Sub:Strength of Material (22306)

Sub:Strength of Material (22306) Sub:Strength of Material (22306) UNIT 1. Moment of Inertia 1.1 Concept of Moment of Inertia (Ml). Effect of MI in case of beam and column. 1.2 MI about axes passing through centroid. Parallel and Perpendicular

More information

Introduction to Matrices

Introduction to Matrices 214 Analysis and Design of Feedback Control Systems Introduction to Matrices Derek Rowell October 2002 Modern system dynamics is based upon a matrix representation of the dynamic equations governing the

More information

1. Diagonalize the matrix A if possible, that is, find an invertible matrix P and a diagonal

1. Diagonalize the matrix A if possible, that is, find an invertible matrix P and a diagonal . Diagonalize the matrix A if possible, that is, find an invertible matrix P and a diagonal 3 9 matrix D such that A = P DP, for A =. 3 4 3 (a) P = 4, D =. 3 (b) P = 4, D =. (c) P = 4 8 4, D =. 3 (d) P

More information

Chapter 7: Bending and Shear in Simple Beams

Chapter 7: Bending and Shear in Simple Beams Chapter 7: Bending and Shear in Simple Beams Introduction A beam is a long, slender structural member that resists loads that are generally applied transverse (perpendicular) to its longitudinal axis.

More information

OUT ON A LIMB AND HUNG OUT TO DRY :

OUT ON A LIMB AND HUNG OUT TO DRY : 27-Nov-12 17:03 1 of 2 h p://edugen.wileyplus.com/edugen/courses/crs1404/pc/c10/c2hlchbhcmq3mjewyzewxzeuegzvcm0.enc?course=crs1404&id=ref CHAPTER 10 OUT ON A LIMB AND HUNG OUT TO DRY : A LOOK AT INTERNAL

More information

Linear Algebra & Geometry why is linear algebra useful in computer vision?

Linear Algebra & Geometry why is linear algebra useful in computer vision? Linear Algebra & Geometry why is linear algebra useful in computer vision? References: -Any book on linear algebra! -[HZ] chapters 2, 4 Some of the slides in this lecture are courtesy to Prof. Octavia

More information

q n. Q T Q = I. Projections Least Squares best fit solution to Ax = b. Gram-Schmidt process for getting an orthonormal basis from any basis.

q n. Q T Q = I. Projections Least Squares best fit solution to Ax = b. Gram-Schmidt process for getting an orthonormal basis from any basis. Exam Review Material covered by the exam [ Orthogonal matrices Q = q 1... ] q n. Q T Q = I. Projections Least Squares best fit solution to Ax = b. Gram-Schmidt process for getting an orthonormal basis

More information

GEOG 4110/5100 Advanced Remote Sensing Lecture 15

GEOG 4110/5100 Advanced Remote Sensing Lecture 15 GEOG 4110/5100 Advanced Remote Sensing Lecture 15 Principal Component Analysis Relevant reading: Richards. Chapters 6.3* http://www.ce.yildiz.edu.tr/personal/songul/file/1097/principal_components.pdf *For

More information

5. What is the moment of inertia about the x - x axis of the rectangular beam shown?

5. What is the moment of inertia about the x - x axis of the rectangular beam shown? 1 of 5 Continuing Education Course #274 What Every Engineer Should Know About Structures Part D - Bending Strength Of Materials NOTE: The following question was revised on 15 August 2018 1. The moment

More information

MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA, & MOMENTS OF INTERTIA BY INTEGRATION

MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA, & MOMENTS OF INTERTIA BY INTEGRATION MOMENTS OF INERTIA FOR AREAS, RADIUS OF GYRATION OF AN AREA, & MOMENTS OF INTERTIA BY INTEGRATION Today s Objectives: Students will be able to: a) Define the moments of inertia (MoI) for an area. b) Determine

More information

Linear Algebra Review. Fei-Fei Li

Linear Algebra Review. Fei-Fei Li Linear Algebra Review Fei-Fei Li 1 / 51 Vectors Vectors and matrices are just collections of ordered numbers that represent something: movements in space, scaling factors, pixel brightnesses, etc. A vector

More information

MECE 3321: Mechanics of Solids Chapter 6

MECE 3321: Mechanics of Solids Chapter 6 MECE 3321: Mechanics of Solids Chapter 6 Samantha Ramirez Beams Beams are long straight members that carry loads perpendicular to their longitudinal axis Beams are classified by the way they are supported

More information

Name (Print) ME Mechanics of Materials Exam # 2 Date: March 29, 2016 Time: 8:00 10:00 PM - Location: PHYS 114

Name (Print) ME Mechanics of Materials Exam # 2 Date: March 29, 2016 Time: 8:00 10:00 PM - Location: PHYS 114 Name (Print) (Last) (First) Instructions: ME 323 - Mechanics of Materials Exam # 2 Date: March 29, 2016 Time: 8:00 10:00 PM - Location: PHYS 114 Circle your lecturer s name and your class meeting time.

More information

TBP MATH33A Review Sheet. November 24, 2018

TBP MATH33A Review Sheet. November 24, 2018 TBP MATH33A Review Sheet November 24, 2018 General Transformation Matrices: Function Scaling by k Orthogonal projection onto line L Implementation If we want to scale I 2 by k, we use the following: [

More information