ORIGIN 0. PTC_CE_BSD_7.2_us_mp.mcdx. Mathcad Enabled Content Copyright 2011 Knovel Corp.

Size: px
Start display at page:

Download "ORIGIN 0. PTC_CE_BSD_7.2_us_mp.mcdx. Mathcad Enabled Content Copyright 2011 Knovel Corp."

Transcription

1 PC_CE_BSD_7._us_mp.mcdx Copyright 011 Knovel Corp. Building Structural Design homas P. Magner, P.E. 011 Parametric echnology Corp. Chapter 7: Reinforced Concrete Column and Wall Footings 7. Pile Footings Disclaimer While Knovel and PC have made every effort to ensure that the calculations, engineering solutions, diagrams and other information (collectively Solution ) presented in this Mathcad worksheet are sound from the engineering standpoint and accurately represent the content of the book on which the Solution is based, Knovel and PC do not give any warranties or representations, express or implied, including with respect to fitness, intended purpose, use or merchantability and/or correctness or accuracy of this Solution. Array origin: ORIGIN 0 Description Pile supported footings or pile caps are used under columns and walls to distribute the load to the piles. he plan dimensions of a pile footing are determined by the number and the arrangement of the piles and the required minimum spacing between the piles. his application determines minimum required pile cap thickness and the maximum size and minimum number of reinforcing bars for pile caps with from to 0 piles in a group. Pile diameter and spacing, and the size of the supported rectangular pier or wall may be specified by the user. he application uses the Strength Design Method of ACI he required input includes the pile capacity at service load (unfactored loads) and the plan dimensions of the column or wall. he user may also enter material properties and variables designated as "project constants" in this application. he material properties include strength of the concrete and the reinforcement, unit weight of concrete, unit weight of reinforced concrete, and the preferred reinforcement ratio. he project constants include pile diameter, minimum pile spacing, edge distance, and multiples used for rounding the pile coordinates, the pile cap depth and the plan dimensions of the pile caps. Copyright 011 Knovel Corp. Page 1 of 41

2 PC_CE_BSD_7._us_mp.mcdx Reference: ACI "Building Code Requirements for Reinforced Concrete." (Revised 199) Input Input Variables Enter service load pile capacity, number of piles in group, and pier or wall dimensions. Pile capacity at service loads: Number of piles in group: Column width: Column depth: P cap 80 kip N 8 C x 4 in C y 4 in If the footing supports a wall, enter any wall length greater than or equal to the dimension of the footing parallel to the wall. Copyright 011 Knovel Corp. Page of 41

3 PC_CE_BSD_7._us_mp.mcdx Computed Variables he following variables are calculated in this document: Ps F Pu qu h X Y x' y' total service load capacity of the piles combined load factor for dead and live load total factored load capacity of the piles and the pile cap factored load capacity of one pile total pile footing thickness the longer dimension of the pile cap the shorter dimension of the pile cap pile coordinates in the X direction from the centroid of the pile group pile coordinates in the Y direction from the centroid of the pile group Input Constants he following variables are normally constant for a given project and may be defined by the user. he variables s, SzP, SzD and E are used by this application to calculate the pile coordinates and plan dimensions of the pile caps. Minimum pile spacing: Multiple for rounding pile spacing: s 3 ft SzP 0.5 in Copyright 011 Knovel Corp. Page 3 of 41

4 PC_CE_BSD_7._us_mp.mcdx Multiple for rounding pile cap plan dimensions: Minimum edge distance from center of pile: SzD 1 in E 1 ft + 3 in Ratio of live load to dead load: Pile diameter at top of pile: Pile embedment into pile cap: Clearance between reinforcement and top of pile: Multiple for rounding footing depths: R 1 d p 8 in e 4 in cl 3 in SzF 1 in Material Properties Enter the values of f'c, fy, wc, wrc, kv and kw. Specified compressive strength of concrete: Specified yield strength of reinforcement: Unit weight of concrete: Unit weight of reinforced concrete: Shear strength reduction factor for lightweight concrete kv = 1 for normal weight, 0.75 for alllightweight and 0.85 for sand-lightweight concrete (ACI 318, ): f' c 4 ksi f y 60 ksi w c 145 pcf w rc 150 pcf k v 1 Copyright 011 Knovel Corp. Page 4 of 41

5 PC_CE_BSD_7._us_mp.mcdx Weight factor for increasing development and splice lengths kw = 1 for normal weight and 1.3 for lightweight aggregate concrete (ACI 318, 1..4.): k w 1 Factors for use of lightweight concrete are included, but it would be unusual to use lightweight concrete for a pile cap. Modulus of elasticity of reinforcement (ACI 318, 8.5.): Strain in concrete at compression failure (ACI 318, 10.3.): Strength reduction factor for flexure (ACI 318, ): Strength reduction factor for shear (ACI 318, ): E s 9000 ksi ε c ϕ f 0.9 ϕ v 0.85 Reinforcing bar number designations, diameters, and areas: No [ ] d b A b [ ] in [ ] in Bar numbers, diameters and areas are in the vector rows (or columns in the transposed vectors shown) corresponding to the bar numbers. Individual bar numbers, diameters and areas of a specific bar can be referred to by using the vector subscripts as shown in the example below. Copyright 011 Knovel Corp. Page 5 of 41

6 PC_CE_BSD_7._us_mp.mcdx Pile Coordinates and Plan Dimensions of Pile Caps Dimensions used to compute pile coordinates: s0 0 ft s1 SzP ceil s sin ( 45 deg) s1 = 4.5 ft SzP s SzP ceil s sin ( 60 deg) SzP s =.65 ft s3 s + s s3 = 4.15 ft s4 s + s s4 = 5.65 ft Angle between the centerline of the two piles in the base row and a centerline drawn between either of the two piles in the base row to the pile at the apex of the 3-pile group: α atan s α = deg s Pile coordinates expressed in terms of pile spacing. he number within the column operator indicates the number of piles in the group: x 1 [ s0 s0 ] y 1 [ s0 s0 ] x s s y [ s0 s0 ] Copyright 011 Knovel Corp. Page 6 of 41

7 PC_CE_BSD_7._us_mp.mcdx x 3 s0 s s x 4 s s s s x 5 s1 s1 s0 s1 s1 y 3 s s 3 3 s 3 y 4 s s s s y 5 s1 s1 s0 s1 s1 x 6 [ s s0 s s s0 s] y 6 s s s s s s x 7 s s s s0 s s s y 7 [ s s s0 s0 s0 s s ] x 8 s s0 s s s s s0 s y 8 [ s s s s0 s0 s s s ] x 9 [ s s0 s s s0 s s s0 s] y 9 [ s s s s0 s0 s0 s s s] x 10 s s0 s 3 s s s s s s0 s y 10 [ s s s s0 s0 s0 s0 s s s ] x 11 3 s s s s s s0 s 3 s s s s y 11 [ s s s s s0 s0 s0 s s s s ] Copyright 011 Knovel Corp. Page 7 of 41

8 PC_CE_BSD_7._us_mp.mcdx x 1 3 s s s s 3 s s s s 3 s s s s y 1 x 13 [ s s s s s0 s0 s0 s0 s s s s] [ s s0 s s s s s0 s s s s s0 s] y 13 s s s s s s0 s0 s0 s s s s s x 14 s s0 s 3 s s s s 3 s s s s s s0 s y 14 s3 s3 s3 s s s s s s s s s3 s3 s3 x 15 y 15 [ s s s0 s s s s s0 s s s s s0 s s] [ s s s s s s0 s0 s0 s0 s0 s s s s s] x 16 3 s s s s 3 s s s s 3 s s s s 3 s s s s y 16 s s s s s s s s s s s s s s s s Copyright 011 Knovel Corp. Page 8 of 41

9 PC_CE_BSD_7._us_mp.mcdx x 17 [ s s s s0 s s s s s0 s s s s s0 s s s ] y 17 s s s s s s s s0 s0 s0 s s s s s 3 s 3 s x 18 [ s s0 s s s s s0 s s s s s0 s s s s s0 s] y 18 s s s s s s s s s0 s0 s s s s s 3 s 3 s 3 s x 19 [ s4 s s s4 s0 s4 s s s4 s0 s4 s s s4 s0 s4 s s s4 ] y 19 s s s s s s s s s s0 s s s s s 3 s 3 s 3 s 3 s x 0 [ s s s0 s s s s s0 s s s s s0 s s s s s0 s s] y 0 s s s s s s s s s s s s s s s 3 s 3 s 3 s 3 s 3 s Pile coordinates in the X and Y directions from the center of the pile group being designed: i 0 N 1 x' x i i, N Copyright 011 Knovel Corp. Page 9 of 41

10 PC_CE_BSD_7._us_mp.mcdx x' = [ ] ft y' y i i, N y' = [ ] ft Absolute values of pile coordinates in the X and Y directions from the center of the pile group being designed: x_abs x' x_abs = [ ] ft y_abs y' y_abs = [ ] ft Absolute values of pile coordinates in the X and Y directions from the center of the pile group being designed minus 1/ the pier width, or the maximum absolute pile coordinate if the pile center is less than half the pier width from the center of the group: x_face if x_abs C x, x_abs C x, max i i i (x_abs) x_face = [ ] ft y_face if y_abs C y, y_abs C y, max i i i (y_abs) Copyright 011 Knovel Corp. Page 10 of 41

11 PC_CE_BSD_7._us_mp.mcdx y_face = [ ] ft Distances ax and ay from face of pier in the X and Y directions to the closest pile center, or 0 ft if all pile centers are less than or equal to 1/ the pier width or depth from the pile group center: a x if max (x_abs) C x, 0 ft, min (x_face) a y if max (y_abs) C y, 0 ft, min (y_face) a x = 6 in a y = 19.5 in Plan dimensions pile caps as function of the number of piles: FX (N) max x N min N x + E FY (N) max y N min N y + E Plan dimensions X and Y of the pile cap being designed: X FX(N) Y FY(N) X= 8.5 ft Y= 7.75 ft Dimensions A and B for the 3-pile group rounded up to a multiple of SzD: A E 1 1 SzD ceil sin (α) tan (α) SzD A= 18 in Copyright 011 Knovel Corp. Page 11 of 41

12 PC_CE_BSD_7._us_mp.mcdx B E 1+ tan (α) 1 1 SzD ceil sin (α) SzD B= 19 in Plan area of pile cap, CapArea: CapArea if FX (3) N 3, X Y, FX (3) FY (3) A ( FY (3) B) CapArea = ft Example: No = 5 d b5 = 0.65 in A b5 = 0.31 in 5 he following values are computed from the entered material properties. Modulus of elasticity of concrete (for values of wc between 90 pcf and 155 pcf (ACI 318, 8.5.1): E c w 1.5 c 33 f' c psi E c = 3644 ksi pcf psi Strain in reinforcement at yield stress: ε y f y ε y = E s Factor used to calculate depth of equivalent rectangular stress block (ACI 318, ): β 1 if f' f' c 4 ksi c 4 ksi f' c 8 ksi, , if f' c 4 ksi, 0.85, 0.65 ksi Copyright 011 Knovel Corp. Page 1 of 41

13 PC_CE_BSD_7._us_mp.mcdx β 1 = 0.85 Reinforcement ratio producing balanced strain conditions (ACI 318, 10.3.): ρ b β f' c E s ε c ρ b =.851% E s ε c + f y f y Maximum reinforcement ratio (ACI 318, ): ρ max 3 4 ρ b ρ max =.138% Minimum reinforcement ratio for beams (ACI 318, , Eq. (10-3)): ρ min 00 lbf ρ = in min 0.333% f y Shrinkage and temperature reinforcement ratio (ACI 318, ): f y ρ temp if f y 50 ksi,.00, if f y 60 ksi, , if ksi ksi.0014,, ksi f y f y Preferred reinforcement ratio: ρ 3 8 ρ b Any reinforcement ratio from min (the minimum reinforcement ratio for flexure) to 3/4 b (the maximum reinforcement ratio) may be specified. Numerical values may also be entered directly, such as 1.0 % or Flexural coefficient K, for rectangular beams or slabs, as a function of (ACI 318, 10.): (Moment capacity Mn = K( F, where F = bd) Copyright 011 Knovel Corp. Page 13 of 41

14 PC_CE_BSD_7._us_mp.mcdx K (ρ) ϕ f K (ρ) = 0.53 ksi ρ ρ f y 1 f y 0.85 f' c Limit the value of f'c for computing shear and development lengths to 10 ksi by substituting f'c_max for f'c in formulas for computing shear and development lengths (ACI 318, 11.1., 1.1.): f' c_max if f' c > 10 ksi, 10 ksi, f' c Nominal "one way" shear strength per unit area in concrete (ACI 318, , Eq. (11-3), ): v c f' c_max k v psi v c = 16 psi psi Basic tension development length ldbt (ACI 318, 1.. and ): No. 3 through No. 11 bars: n 3 11 X1 n f y 0.04 A bn lbf f' c_max X n f y 0.03 d bn f' c_max psi psi l dbtn if X1 > X, X1, X n n n n l dbt = [ ] in Copyright 011 Knovel Corp. Page 14 of 41

15 PC_CE_BSD_7._us_mp.mcdx No. 14 bars: l dbt14 f y in lbf f' c_max l dbt14 = 80.6 in No. 18 bars l dbt18 f y in 0.15 lbf f' c_max l dbt18 = in ension development length (ACI 318, 1..1): No. 3 through No. 11 bars: l dtn if k w l dbtn 1 in, k w l dbtn, if k w l dbtn > 0 in, 1 in, 0 in l dt = [ ] in No. 14 bars: l dt14 k w l dbt14 = 80.6 in l dt14 No. 18 bars l dt18 k w l dbt18 = in l dt18 Solution Service load: P s P cap N = 640 kip P s Combined load factor for dead + live load: F R 1+ R F= 1.55 Copyright 011 Knovel Corp. Page 15 of 41

16 PC_CE_BSD_7._us_mp.mcdx Factored load Pu: P u F N P cap = 99 kip Factored load per pile: P u q u P u N q u = 14 kip he longer dimension of the pile cap: X= 8.5 ft he shorter dimension of the pile cap: Y= 7.75 ft Range variable i from 0 to the number of piles N, minus 1: i 0 N 1 Pile coordinates in the X direction from the centerline of the pile group, starting from top left to bottom right: x' = [ ] ft Pile coordinates in the Y direction from the centerline of the pile group, starting from left to right and top to bottom: y' = [ ] ft Copyright 011 Knovel Corp. Page 16 of 41

17 PC_CE_BSD_7._us_mp.mcdx Solution to determine the minimum required footing depth for flexure, df Bending moment about the Y axis as function of distance x from Y axis: M y (x) i q u if x' x, 0 ft, x' x i i Bending moment about the Y axis at face of pier: M y C x = 558 kip ft Bending moment about the X axis as function of distance y from X axis: M x (y) i q u if y' y, 0 ft, y' y i i Bending moment about the X axis at face of pier: M x C y = kip ft Effective footing width for bending about the X axis, at face of pier: X f if N 3, X, A+ E+ 3 s C y X A Y B X f = 8.5 ft Copyright 011 Knovel Corp. Page 17 of 41

18 PC_CE_BSD_7._us_mp.mcdx Effective footing widths for flexure and shear vary with distance from the pile group centroid for the 3- pile group. he remaining pile caps are rectangular in shape and the full width is effective for flexure or shear at any section. Effective footing width at face of pier, for bending about the Y axis: Y f Y if ( N 3) + C x A, 0 ft, C x A X A ( Y B) Y f = 7.75 ft Maximum bending moment per unit width: M u M x C y M y C x M x C y M y C x if >,, X f Y f X f Y f = M u kip 7 ft ft Minimum required effective footing depth for flexure at specified reinforcement ratio (ACI 318, 10.): d f M u K (ρ) d f = in Solution to determine the minimum required footing depth for one-way beam shear, dbm Shear Vux(x) in the X direction as a function of any specified positive distance x from the Y axis (ACI 318, ): Copyright 011 Knovel Corp. Page 18 of 41

19 PC_CE_BSD_7._us_mp.mcdx V ux (x) i if x' C x + d p, 0, if x' x + i i d p,, 1 if x' x i d p x' + d p x i,, 0 d p q u Shear Vuy(y) in the Y direction as a function of any specified positive distance y from the X axis (ACI 318, ): V uy (y) i if y' C y + i d p,, 0 if y' y + i d p, 1, if y' y i d p y' + d p y i, 0, d p q u Since the 3-pile group is not rectangular the effective width in the X and Y directions varies with distance from the pile group centroid. he shear must be checked at both the inside edge of the piles and at distance d from the face of the pier. he following functions are for calculating the effective widths and required depths at any positive distance from the pile group centroid, and the required depths at distance d from the face of the pier. he largest required depth at distance d from the face of pier or at the inside edge of the piles determines the minimum required depth for the 3-pile group. Effective footing width for one-way shear in the Y direction for the 3-pile group, as a function of any positive distance y from the X axis: X 3 (y) A+ ( E + max (y') y) X A Y B Minimum required depth for one-way shear in the Y direction for the 3-pile group as a function of any positive distance y from the X axis: d y3 (y) if y C y, 0 ft, if V uy (y) < y C y,, ϕ v v c X 3 (y) V uy (y) y C y ϕ v v c X 3 (y) Copyright 011 Knovel Corp. Page 19 of 41

20 PC_CE_BSD_7._us_mp.mcdx Effective footing width for one-way shear in the X direction for the 3-pile group, as a function of any positive distance x from the Y axis: Y 3 (x) Y if C x + x A, 0 ft, C x + x A Y B X A Minimum required depth for one-way shear in the X direction for the 3-pile group as a function of any positive distance x from the Y axis: d x3 (x) if x C x, 0 ft, if V ux (x) < x C x,, ϕ v v c Y 3 (x) V ux (x) x C x ϕ v v c Y 3 (x) Minimum required depth for one-way shear in the X direction for the 3-pile group at distance d from face of pier: Guess Values d 1 ft d max (x') + d p Constraints Solver V ux C x + d = ϕ v v c Y 3 C x + d d d x3_d (d) Find (d) Copyright 011 Knovel Corp. Page 0 of 41

21 PC_CE_BSD_7._us_mp.mcdx Minimum required depth for one-way shear in the Y direction for the 3-pile group at distance d from face of pier: Guess Values d 1 ft d max (y') + d p Constraints V uy C y + d = ϕ v v c X 3 C y + d d Solver d y3_d (d) Find (d) Copyright 011 Knovel Corp. Page 1 of 41

22 PC_CE_BSD_7._us_mp.mcdx Functions for rectangular pile caps he following Mathcad solve blocks contain the functions for determining the required depth for oneway shear for the rectangular pile caps. Minimum required depth for one-way shear in the X direction at distance d from face of pier: Guess Values d 1 ft d max (x') + d p Constraints V ux C x + d =d ϕ v v c Y Solver d x (d) Find (d) Minimum required depth in the Y direction at distance d from face of pier: Guess Values Constraints Solver d 1 ft d max (y') + d p V uy C y + d =d ϕ v v c X d y (d) Find (d) Copyright 011 Knovel Corp. Page of 41

23 PC_CE_BSD_7._us_mp.mcdx d 1 ft Depth required for one-way shear in the Y direction: d y d if N 3, d y (d), max y3 max (y') d y3_d (d) d y = in Depth required for one-way shear in the X direction: d p d x d if N 3, d x (d), max x3 max (x') d x3_d (d) d x = in d p Minimum depth required for beam shear: d bm max d x d d bm = in y Copyright 011 Knovel Corp. Page 3 of 41

24 PC_CE_BSD_7._us_mp.mcdx Calculations to determine the minimum required footing depth for peripheral shear, dper (ACI 318, ) Critical Sections for Peripheral Shear (d is the effective depth and dp is the pile diameter) Perimeter of critical section for slabs and footings expressed as a function of d (ACI 318, ): b o (d) C x + C y + d Ratio of the longer to the shorter pier dimension (ACI ): C x β c if C x C y,, β c = 1 C x C y C y Copyright 011 Knovel Corp. Page 4 of 41

25 PC_CE_BSD_7._us_mp.mcdx Nominal "two way" concrete shear strength per unit area in slabs and footings, expressed as a function of effective depth d. Since piers or columns are at the center of the pile cap they are considered "interior" columns for calculating two way shear, and s is equal to 40. (ACI , Eqs. (11-36), (11-37) and (11-38)): α s 40 v cp (d) + 4 β c min α s d b o (d) 4 k v f' c_max psi psi Function V1(d) computes a vector with elements equal to 0 if the pile produces shear on the critical section and 1 if it does not: V1 (d) x' C x + d d p y' C y + d d p Function V(d) computes a vector with elements equal to 1 if the full reaction of the pile produces shear on the critical section and 0 if it does not: V (d) x' C x + d + d p + y' C y + d + d p > 0 Function V3(d) computes a vector with elements equal to 1 if a portion of the pile reaction produces shear on the critical section and 0 if it does not: V3 (d) 1 V1(d) V (d) Copyright 011 Knovel Corp. Page 5 of 41

26 PC_CE_BSD_7._us_mp.mcdx Function V4(d) computes a vector with elements equal to the the larger difference between the x' or y' pile coordinate and the corresponding distance to the shear section minus half the pile diameter or 0 ft. V4 (d) V3 (d) x' > + C x + d d p 0 ft x' C x + d d p V3 (d) y' > C y + d d p 0 ft y' C y + d d p Shear Vup(d) on the peripheral shear section at distance d/ from the face of the pier, expressed as a function of d (ACI 318, ): V up (d) V4 (d) V (d) + q u d p Guess value of d: d d bm d' per (d) root V up (d) ϕ v v cp (d), d b o (d) d d' per if C x + d bm X + C y + d bm Y, d bm, d' per (d) d' per = in Minimum depth for peripheral shear dper: d per if C x + d' per X + C y + d' per Y, d bm, d' per d per = in Copyright 011 Knovel Corp. Page 6 of 41

27 PC_CE_BSD_7._us_mp.mcdx If either dimension of the critical shear section is greater than the corresponding pile cap dimension, peripheral shear is not critical and the depth for peripheral shear is defined as equal to the depth required for one-way shear. Calculation to determine the minimum required depth for deep beam shear dbm (ACI 318, 11.8, using Eq. (11-30) for shear strength) Shear spans in the X and Y directions are one-half the distances between the closest pile row and the face of the pier (See ACI 318, Chapter 11 Notation, and 11.8): 0.5 a x = 0.5 ft 0.5 a y = ft Moment and shear in the X and Y directions on the critical shear sections at distance 0.5ax and 0.5ay from the face of the pier (ACI 318, ): C x M y a x = 465 kip ft Copyright 011 Knovel Corp. Page 7 of 41

28 PC_CE_BSD_7._us_mp.mcdx C x V ux a x = kip M x C y a y = 30.5 kip ft V uy C y a y = 37 kip Ratios of moment to shear Rx and Ry, at the critical sections for deep beam shear in the X and Y directions: C x M y a x R x V ux C R x = ft x a x M x C y a y R y V uy C R y = ft y a y Multipliers for use in ACI 318, Eq. (11-30): KX (d) if R x < 1, 1, if R x >.5,.5, R x d d d Copyright 011 Knovel Corp. Page 8 of 41

29 PC_CE_BSD_7._us_mp.mcdx KY (d) if R y < 1, 1, if R y >.5,.5, R y d d d Nominal deep beam shear stress at factored load in the X and Y directions (ACI 318, , Eq. (11-30)) with w conservatively assumed equal to minimum temperature reinforcement, temp: v cx (d) v cy (d) KX (d) 1.9 f' c ρ temp d psi min psi R x 6 f' c psi psi KY (d) 1.9 f' c ρ temp d psi min psi R y 6 f' c psi psi Effective depth required in the X direction for deep beam shear: Guess value of d: d d x V ux C x a x d bm_x root, ϕ v v cx (d) if N 3, Y, Y 3 C d d x a x d bm_x = in v cx d bm_x = 10.9 psi Copyright 011 Knovel Corp. Page 9 of 41

30 PC_CE_BSD_7._us_mp.mcdx Effective depth required in the Y direction for deep beam shear: Guess value of d: d d y V uy C y a y d bm_y root, ϕ v v cy (d) if N 3, X, X 3 C d d y a y d bm_y = in v cy d bm_y = 59. psi Depth required for deep beam shear is the larger value of dbm: d bm max d bm_x d bm_y d bm = in Copyright 011 Knovel Corp. Page 30 of 41

31 PC_CE_BSD_7._us_mp.mcdx Solution to determine the minimum required depth for beam shear or peripheral shear for one corner pile, dcor Critical Section for Beam Shear for 1 corner pile Critical Section for Peripheral Shear for 1 corner pile Required depth for beam shear for one corner pile Guess value of d: d 1 ft d cor_1 q u root, ϕ v v c d p + d+ E d d d cor_1 = in Required depth for peripheral shear for one corner pile Nominal "two way" concrete shear strength per unit area in slabs and footings, expressed as a function of effective depth d. For a corner pile s is equal to 0. Since c is 1 for piles in this application, ACI 318 Eq. (11-36) is not critical (ACI 318, , Eqs. (11-37) and (11-38)): Copyright 011 Knovel Corp. Page 31 of 41

32 PC_CE_BSD_7._us_mp.mcdx α s 0 b o (d) d p + d π 4 + E v cp (d) min α s d b o (d) 4 + k v f' c_max psi psi d cor_ root q u d, d ϕ v v cp (d) b o (d) d cor_ = in Depth required for one corner pile is the larger value of dcor: d cor max d cor_1 d cor_ d cor = in Depth required for a single interior pile, done Nominal "two way" concrete shear strength per unit area for one interior pile, expressed as a function of effective depth d. For an interior pile s is equal to 40 Since c is 1 for piles in this application ACI 318 Eq. (11-36) is not critical. (ACI , Eqs. (11-37) and (11-38)): α s 40 b o (d) π d p + d v cp (d) min α s d b o (d) 4 + k v f' c_max psi psi Copyright 011 Knovel Corp. Page 3 of 41

33 PC_CE_BSD_7._us_mp.mcdx d one root b o (d) d ϕ v v cp (d) q u, d d one = in Depth required for two interior piles, dtwo Nominal "two way" concrete shear strength per unit area for two interior piles, expressed as a function of effective depth d. For interior piles s is equal to 40 (ACI 318, , Eqs. (11-37) and (11-38)): α s 40 β c (d) s+ d+ d p + d d p b o (d) π d p + d + ( s+ d) v cp (d) + 4 β c (d) min α s d + b o (d) 4 k v f' c_max psi psi Depth, dtwo, required for two adjacent piles is equal to done unless overlapping shear perimeters require a greater depth when spacing s is less than done + dp: d two if d p + d one s, d one, root b o (d) d ϕ v v cp (d) q u, d d two = in Copyright 011 Knovel Corp. Page 33 of 41

34 PC_CE_BSD_7._us_mp.mcdx Minimum thickness for a footing on piles (ACI 318, 15.7): d min 1 in Minimum required effective depth, de Largest effective depth determined by flexure, one-way beam shear, peripheral shear, deep beam shear, shear on a single corner pile, a single interior pile, two adjacent piles, or the minimum thickness required for a footing on piles de: d f d bm d per d bm d cor d one d two d min = in d e max d f d bm d per d bm d cor d one d two d min d e = in Solution to determine the largest permissible reinforcing bar sizes Maximum available lengths in the X direction for development of reinforcement: L dx X C x 3 in L dx = 3 ft Copyright 011 Knovel Corp. Page 34 of 41

35 PC_CE_BSD_7._us_mp.mcdx Maximum available lengths in the Y direction for development of reinforcement. he available development length for the 3-pile group is calculated from face of pier to the pile at the apex of the group: L dy + if Y C y 3 s E C y N 3,, 3 in L dy =.65 ft sin (α) Index numbers of maximum bar sizes determined by available development lengths: index 0 index if l dtn L,, 0 0 n dx n index 0 bx index bx = 8 0 index 0 index if l dtn L,, 0 0 n dy n index 0 by index by = 8 0 Sizes of the largest permissible reinforcing bars for the X and Y directions. Since the 3-pile group uses three equal bands of reinforcement the maximum bar size is defined as the smaller bar size for either the X or Y direction: BarSize_X if N 3, bx, min bx by BarSize_X = 8 bx BarSize_X = 1 in d bbx BarSize_Y if N 3, by, min bx by BarSize_Y = 8 Copyright 011 Knovel Corp. Page 35 of 41

36 PC_CE_BSD_7._us_mp.mcdx by BarSize_Y = 1 in d bby otal pile cap thickness rounded up to the nearest multiple of SzF: h d e + d bbx d bby + cl + e SzF ceil SzF h= 30 in Pile cap weight: CapWt CapArea h w rc CapWt = kip Calculation to determine the required number of reinforcing bars in the X and Y directions Effective depths in the X and Y directions: d ex h e cl 0.5 d bbx =.5 in d ex d ey h e cl d bbx 0.5 d bby = 1.5 in d ey otal required flexural reinforcement area in the X direction: A sx_flex Y f d ex 1 M y C x 1 ϕ f Y f d 0.85 f' c ex 0.85 f' c f y A sx_flex = in Copyright 011 Knovel Corp. Page 36 of 41

37 PC_CE_BSD_7._us_mp.mcdx Minimum required reinforcement area for shrinkage and temperature in the X direction (ACI 318, 7.1): A sx_temp ρ temp h Y A sx_temp = 5.0 in Larger required reinforcement in the X direction: A sx max A sx_flex A sx_temp A sx = in otal required reinforcement area for flexure in the Y direction: A sy_flex if N, X f d ey 1 M x C y 1, ϕ f X f d 0.85 f' c ey 0.85 f' c f 0 in y A sy_flex = in Minimum required reinforcement area for shrinkage and temperature in the Y direction (ACI 318, 7.1): A sy_temp ρ temp h X A sy_temp = in Larger required reinforcement in the Y direction: A sy max A sy_flex A A sy = in sy_temp Copyright 011 Knovel Corp. Page 37 of 41

38 PC_CE_BSD_7._us_mp.mcdx Minimum number of bars to limit spacing of reinforcement to 18 inches (ACI 318, 7.6.5): MinNumb_X ceil Y 6 in MinNumb_X = 6 18 in MinNumb_Y ceil X 6 in MinNumb_Y = 6 18 in Maximum bar areas corresponding to minimum specified spacing: MinA_x A sx MinNumb_X MinA_x = in MinA_y A sy MinNumb_Y MinA_y = in Index numbers of bar sizes determined by minimum specified spacing: index 0 index if 0 0 n ax index ax = 8 0 A bn MinA_x, n, index 0 index 0 index if 0 0 n ay index ay = 9 0 A bn MinA_y, n, index 0 Copyright 011 Knovel Corp. Page 38 of 41

39 PC_CE_BSD_7._us_mp.mcdx Actual bar sizes in the X and Y directions. Bar sizes in the X and Y directions (the smaller bar area determined by the required total reinforcement or the specified minimum spacing). he bar size in the Y direction of the -pile group is set at 3: BarSixe_X if M y C x =0 kip ft + ( ax bx), ax, bx BarSixe_X = 8 BarSize_Y if N, if M x C y =0 kip ft + ( ay by), ay, by, 3 BarSize_Y = 8 Subscript variables cx and cy defined as the bar sizes in the X and Y directions, respectively: cx BarSize_X cy BarSize_Y Adjustments required in reinforcement areas for the 3-pile group In the the 3-pile group the reinforcement is customarily placed in 3 bands of equal area, over the pile centers. Because the bands are at an angle to the axes of bending the reinforcement areas must be adjusted accordingly. otal required reinforcement area in each of 3 bands for the 3-pile group: A sx if N 3, A sx, if A sx A sy >,, sin (α) 1 + cos (α) A sx sin (α) A sy 1 + cos (α) A sx = in Copyright 011 Knovel Corp. Page 39 of 41

40 PC_CE_BSD_7._us_mp.mcdx A sy if N 3, A sy, A sx A sy = in Number of bars required in the X and Y directions. he number of bars in Y direction of the -pile group is set at a multiple of 18 inches: Numb_X A sx ceil Numb_X = 8 A bcx Numb_Y if N, ceil A sy, ceil X A bcy 18 in Numb_Y = 9 Summary Computed Variables Combined load factor for dead and live load: F= 1.55 otal service load capacity of the piles and the pile cap: = 640 kip P s otal factored load capacity of the piles and the pile cap: P u = 99 kip Number of reinforcing bars in the X direction: Numb_X = 8 Copyright 011 Knovel Corp. Page 40 of 41

41 PC_CE_BSD_7._us_mp.mcdx Bar size in the X direction: BarSize_X = 8 Number of reinforcing bars in the Y direction: Numb_Y = 9 Bar size in the Y direction: BarSize_Y = 8 he number and size of reinforcing bars for the 3-pile group is shown as equal in the X and Y directions. he reinforcement for the 3-pile group consists of three equal bands over the three centerlines of the piles, with the number and size of bars of the bars in each band equal to that shown for the X and Y directions. Longer dimension of the pile cap: X= 8.5 ft Shorter dimension of the pile cap: Y= 7.75 ft otal pile footing thickness: h= 30 in otal pile cap weight: CapWt = kip User Notices Equations and numeric solutions presented in this Mathcad worksheet are applicable to the specific example, boundary condition or case presented in the book. Although a reasonable effort was made to generalize these equations, changing variables such as loads, geometries and spans, materials and other input parameters beyond the intended range may make some equations no longer applicable. Modify the equations as appropriate if your parameters fall outside of the intended range. For this Mathcad worksheet, the global variable defining the beginning index identifier for vectors and arrays, ORIGIN, is set as specified in the beginning of the worksheet, to either 1 or 0. If ORIGIN is set to 1 and you copy any of the formulae from this worksheet into your own, you need to ensure that your worksheet is using the same ORIGIN. Copyright 011 Knovel Corp. Page 41 of 41

3.5 Reinforced Concrete Section Properties

3.5 Reinforced Concrete Section Properties CHAPER 3: Reinforced Concrete Slabs and Beams 3.5 Reinforced Concrete Section Properties Description his application calculates gross section moment of inertia neglecting reinforcement, moment of inertia

More information

3.4 Reinforced Concrete Beams - Size Selection

3.4 Reinforced Concrete Beams - Size Selection CHAPER 3: Reinforced Concrete Slabs and Beams 3.4 Reinforced Concrete Beams - Size Selection Description his application calculates the spacing for shear reinforcement of a concrete beam supporting a uniformly

More information

ORIGIN 1. PTC_CE_BSD_3.2_us_mp.mcdx. Mathcad Enabled Content 2011 Knovel Corp.

ORIGIN 1. PTC_CE_BSD_3.2_us_mp.mcdx. Mathcad Enabled Content 2011 Knovel Corp. Clck to Vew Mathcad Document 2011 Knovel Corp. Buldng Structural Desgn. homas P. Magner, P.E. 2011 Parametrc echnology Corp. Chapter 3: Renforced Concrete Slabs and Beams 3.2 Renforced Concrete Beams -

More information

4.3 Moment Magnification

4.3 Moment Magnification CHAPTER 4: Reinforced Concrete Columns 4.3 Moment Magnification Description An ordinary or first order frame analysis does not include either the effects of the lateral sidesway deflections of the column

More information

Lecture 7 Two-Way Slabs

Lecture 7 Two-Way Slabs Lecture 7 Two-Way Slabs Two-way slabs have tension reinforcing spanning in BOTH directions, and may take the general form of one of the following: Types of Two-Way Slab Systems Lecture 7 Page 1 of 13 The

More information

Serviceability Deflection calculation

Serviceability Deflection calculation Chp-6:Lecture Goals Serviceability Deflection calculation Deflection example Structural Design Profession is concerned with: Limit States Philosophy: Strength Limit State (safety-fracture, fatigue, overturning

More information

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram

ε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram CHAPTER NINE COLUMNS 4 b. The modified axial strength in compression is reduced to account for accidental eccentricity. The magnitude of axial force evaluated in step (a) is multiplied by 0.80 in case

More information

Lecture-04 Design of RC Members for Shear and Torsion

Lecture-04 Design of RC Members for Shear and Torsion Lecture-04 Design of RC Members for Shear and Torsion By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Topics Addressed Design of

More information

PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT

PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT Structural Concrete Software System TN191_PT7_punching_shear_aci_4 011505 PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT 1. OVERVIEW Punching shear calculation applies to column-supported slabs, classified

More information

Chapter 8. Shear and Diagonal Tension

Chapter 8. Shear and Diagonal Tension Chapter 8. and Diagonal Tension 8.1. READING ASSIGNMENT Text Chapter 4; Sections 4.1-4.5 Code Chapter 11; Sections 11.1.1, 11.3, 11.5.1, 11.5.3, 11.5.4, 11.5.5.1, and 11.5.6 8.2. INTRODUCTION OF SHEAR

More information

Flexure: Behavior and Nominal Strength of Beam Sections

Flexure: Behavior and Nominal Strength of Beam Sections 4 5000 4000 (increased d ) (increased f (increased A s or f y ) c or b) Flexure: Behavior and Nominal Strength of Beam Sections Moment (kip-in.) 3000 2000 1000 0 0 (basic) (A s 0.5A s ) 0.0005 0.001 0.0015

More information

Appendix J. Example of Proposed Changes

Appendix J. Example of Proposed Changes Appendix J Example of Proposed Changes J.1 Introduction The proposed changes are illustrated with reference to a 200-ft, single span, Washington DOT WF bridge girder with debonded strands and no skew.

More information

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed.

Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. ARCH 631 Note Set 11 S017abn Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. Building description The building is a three-story office building

More information

1/2. E c Part a The solution is identical for grade 40 and grade 60 reinforcement. P s f c n A s lbf. The steel carries 13.3 percent of the load

1/2. E c Part a The solution is identical for grade 40 and grade 60 reinforcement. P s f c n A s lbf. The steel carries 13.3 percent of the load 1/2 3.1. A 16 20 in. column is made of the same concrete and reinforced with the same six No. 9 (No. 29) bars as the column in Examples 3.1 and 3.2, except t hat a steel with yield strength f y = 40 ksi

More information

Unbraced Column Verification Example. AISC Design Examples AISC 13 th Edition. ASDIP Steel is available for purchase online at

Unbraced Column Verification Example. AISC Design Examples AISC 13 th Edition. ASDIP Steel is available for purchase online at Unbraced Column Verification Example AISC Design Examples AISC 3 th Edition IP Steel is available for purchase onle at www.asdipsoft.com H-9 Example H.4 W-Shape Subject to Combed Axial Compression and

More information

This Technical Note describes how the program checks column capacity or designs reinforced concrete columns when the ACI code is selected.

This Technical Note describes how the program checks column capacity or designs reinforced concrete columns when the ACI code is selected. COMPUTERS AND STRUCTURES, INC., BERKELEY, CALIFORNIA DECEMBER 2001 CONCRETE FRAME DESIGN ACI-318-99 Technical Note This Technical Note describes how the program checks column capacity or designs reinforced

More information

Lecture-05 Serviceability Requirements & Development of Reinforcement

Lecture-05 Serviceability Requirements & Development of Reinforcement Lecture-05 Serviceability Requirements & Development of Reinforcement By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Section 1: Deflections

More information

Interaction Diagram Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements

Interaction Diagram Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements Interaction Diagram Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements Interaction Diagram - Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements Investigate the capacity for the irregular

More information

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture

twenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture twenty one concrete construction: Copyright Kirk Martini shear & deflection Concrete Shear 1 Shear in Concrete

More information

Lecture-08 Gravity Load Analysis of RC Structures

Lecture-08 Gravity Load Analysis of RC Structures Lecture-08 Gravity Load Analysis of RC Structures By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar www.drqaisarali.com 1 Contents Analysis Approaches Point of Inflection Method Equivalent

More information

Therefore, for all members designed according to ACI 318 Code, f s =f y at failure, and the nominal strength is given by:

Therefore, for all members designed according to ACI 318 Code, f s =f y at failure, and the nominal strength is given by: 5.11. Under-reinforced Beams (Read Sect. 3.4b oour text) We want the reinforced concrete beams to fail in tension because is not a sudden failure. Therefore, following Figure 5.3, you have to make sure

More information

Design of a Balanced-Cantilever Bridge

Design of a Balanced-Cantilever Bridge Design of a Balanced-Cantilever Bridge CL (Bridge is symmetric about CL) 0.8 L 0.2 L 0.6 L 0.2 L 0.8 L L = 80 ft Bridge Span = 2.6 L = 2.6 80 = 208 Bridge Width = 30 No. of girders = 6, Width of each girder

More information

This procedure covers the determination of the moment of inertia about the neutral axis.

This procedure covers the determination of the moment of inertia about the neutral axis. 327 Sample Problems Problem 16.1 The moment of inertia about the neutral axis for the T-beam shown is most nearly (A) 36 in 4 (C) 236 in 4 (B) 136 in 4 (D) 736 in 4 This procedure covers the determination

More information

Design of Reinforced Concrete Beam for Shear

Design of Reinforced Concrete Beam for Shear Lecture 06 Design of Reinforced Concrete Beam for Shear By: Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk Topics Addressed Shear Stresses in Rectangular Beams Diagonal Tension

More information

Design of Reinforced Concrete Beam for Shear

Design of Reinforced Concrete Beam for Shear Lecture 06 Design of Reinforced Concrete Beam for Shear By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk 1 Topics Addressed Shear Stresses in Rectangular

More information

MECHANICS OF MATERIALS Sample Problem 4.2

MECHANICS OF MATERIALS Sample Problem 4.2 Sample Problem 4. SOLUTON: Based on the cross section geometry, calculate the location of the section centroid and moment of inertia. ya ( + Y Ad ) A A cast-iron machine part is acted upon by a kn-m couple.

More information

Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads

Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com Prof.

More information

Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design

Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department

More information

Chapter 2. Design for Shear. 2.1 Introduction. Neutral axis. Neutral axis. Fig. 4.1 Reinforced concrete beam in bending. By Richard W.

Chapter 2. Design for Shear. 2.1 Introduction. Neutral axis. Neutral axis. Fig. 4.1 Reinforced concrete beam in bending. By Richard W. Chapter 2 Design for Shear By Richard W. Furlong 2.1 Introduction Shear is the term assigned to forces that act perpendicular to the longitudinal axis of structural elements. Shear forces on beams are

More information

Sway Column Example. PCA Notes on ACI 318

Sway Column Example. PCA Notes on ACI 318 Sway Column Example PCA Notes on ACI 318 ASDIP Concrete is available for purchase online at www.asdipsoft.com Example 11.2 Slenderness Effects for Columns in a Sway Frame Design columns C1 and C2 in the

More information

Annex - R C Design Formulae and Data

Annex - R C Design Formulae and Data The design formulae and data provided in this Annex are for education, training and assessment purposes only. They are based on the Hong Kong Code of Practice for Structural Use of Concrete 2013 (HKCP-2013).

More information

Design 1 Calculations

Design 1 Calculations Design 1 Calculations The following calculations are based on the method employed by Java Module A and are consistent with ACI318-99. The values in Fig. 1 below were taken from the Design 1 Example found

More information

Steel Cross Sections. Structural Steel Design

Steel Cross Sections. Structural Steel Design Steel Cross Sections Structural Steel Design PROPERTIES OF SECTIONS Perhaps the most important properties of a beam are the depth and shape of its cross section. There are many to choose from, and there

More information

SERVICEABILITY OF BEAMS AND ONE-WAY SLABS

SERVICEABILITY OF BEAMS AND ONE-WAY SLABS CHAPTER REINFORCED CONCRETE Reinforced Concrete Design A Fundamental Approach - Fifth Edition Fifth Edition SERVICEABILITY OF BEAMS AND ONE-WAY SLABS A. J. Clark School of Engineering Department of Civil

More information

A.2 AASHTO Type IV, LRFD Specifications

A.2 AASHTO Type IV, LRFD Specifications A.2 AASHTO Type IV, LRFD Specifications A.2.1 INTRODUCTION A.2.2 DESIGN PARAMETERS 1'-5.0" Detailed example showing sample calculations for design of typical Interior AASHTO Type IV prestressed concrete

More information

PEER/SSC Tall Building Design. Case study #2

PEER/SSC Tall Building Design. Case study #2 PEER/SSC Tall Building Design Case study #2 Typical Plan View at Ground Floor and Below Typical Plan View at 2 nd Floor and Above Code Design Code Design Shear Wall properties Shear wall thickness and

More information

Figure 1: Representative strip. = = 3.70 m. min. per unit length of the selected strip: Own weight of slab = = 0.

Figure 1: Representative strip. = = 3.70 m. min. per unit length of the selected strip: Own weight of slab = = 0. Example (8.1): Using the ACI Code approximate structural analysis, design for a warehouse, a continuous one-way solid slab supported on beams 4.0 m apart as shown in Figure 1. Assume that the beam webs

More information

Design of a Multi-Storied RC Building

Design of a Multi-Storied RC Building Design of a Multi-Storied RC Building 16 14 14 3 C 1 B 1 C 2 B 2 C 3 B 3 C 4 13 B 15 (S 1 ) B 16 (S 2 ) B 17 (S 3 ) B 18 7 B 4 B 5 B 6 B 7 C 5 C 6 C 7 C 8 C 9 7 B 20 B 22 14 B 19 (S 4 ) C 10 C 11 B 23

More information

UC Berkeley CE 123 Fall 2017 Instructor: Alan Kren

UC Berkeley CE 123 Fall 2017 Instructor: Alan Kren CE 123 - Reinforced Concrete Midterm Examination No. 2 Instructions: Read these instructions. Do not turn the exam over until instructed to do so. Work all problems. Pace yourself so that you have time

More information

Moment Redistribution

Moment Redistribution TIME SAVING DESIGN AID Page 1 of 23 A 3-span continuous beam has center-to-center span lengths of 30 ft-0 in. The beam is 20 in. by 28 in. and all columns are 20 in. by 20 in. In this example, the beam

More information

Bending and Shear in Beams

Bending and Shear in Beams Bending and Shear in Beams Lecture 3 5 th October 017 Contents Lecture 3 What reinforcement is needed to resist M Ed? Bending/ Flexure Section analysis, singly and doubly reinforced Tension reinforcement,

More information

Chapter. Materials. 1.1 Notations Used in This Chapter

Chapter. Materials. 1.1 Notations Used in This Chapter Chapter 1 Materials 1.1 Notations Used in This Chapter A Area of concrete cross-section C s Constant depending on the type of curing C t Creep coefficient (C t = ε sp /ε i ) C u Ultimate creep coefficient

More information

5. What is the moment of inertia about the x - x axis of the rectangular beam shown?

5. What is the moment of inertia about the x - x axis of the rectangular beam shown? 1 of 5 Continuing Education Course #274 What Every Engineer Should Know About Structures Part D - Bending Strength Of Materials NOTE: The following question was revised on 15 August 2018 1. The moment

More information

DEFLECTION CALCULATIONS (from Nilson and Nawy)

DEFLECTION CALCULATIONS (from Nilson and Nawy) DEFLECTION CALCULATIONS (from Nilson and Nawy) The deflection of a uniformly loaded flat plate, flat slab, or two-way slab supported by beams on column lines can be calculated by an equivalent method that

More information

Two-Way Flat Plate Concrete Floor System Analysis and Design

Two-Way Flat Plate Concrete Floor System Analysis and Design Two-Way Flat Plate Concrete Floor System Analysis and Design Version: Aug-10-017 Two-Way Flat Plate Concrete Floor System Analysis and Design The concrete floor slab system shown below is for an intermediate

More information

8/11/14. Sheet 1. Colonial Flag 9390 So 300 West Sandy, UT

8/11/14. Sheet 1. Colonial Flag 9390 So 300 West Sandy, UT 8/11/14 Sheet 1 990 So 00 West Sandy, UT 84070 800 78-0500 Street Banner Sign Cloth Tension Calculations for Simple Span with Uniform Loads. Sign Cloth Span Sign Cloth Length Stretched Sign Cloth Sag Sign

More information

CE5510 Advanced Structural Concrete Design - Design & Detailing of Openings in RC Flexural Members-

CE5510 Advanced Structural Concrete Design - Design & Detailing of Openings in RC Flexural Members- CE5510 Advanced Structural Concrete Design - Design & Detailing Openings in RC Flexural Members- Assoc Pr Tan Kiang Hwee Department Civil Engineering National In this lecture DEPARTMENT OF CIVIL ENGINEERING

More information

Column Design. Columns Axial Load and Bending

Column Design. Columns Axial Load and Bending Column Design MORGAN STATE UNIVERSITY SCHOOL OF ARCHITECTURE AND PLANNING LECTURE VI Dr. Jason E. Charalambides = = Columns Axial Load and Bending We tend to have this image of columns that we envision

More information

Appendix K Design Examples

Appendix K Design Examples Appendix K Design Examples Example 1 * Two-Span I-Girder Bridge Continuous for Live Loads AASHTO Type IV I girder Zero Skew (a) Bridge Deck The bridge deck reinforcement using A615 rebars is shown below.

More information

Anchor Bolt Design (Per ACI and "Design of Reinforcement in Concrete Pedestals" CSA Today, Vol III, No. 12)

Anchor Bolt Design (Per ACI and Design of Reinforcement in Concrete Pedestals CSA Today, Vol III, No. 12) Anchor Bolt Design (Per ACI 318-08 and "Design of Reinforcement in Concrete Pedestals" CSA Today, Vol III, No. 12) Design Assumptions: Base Units and Design 1. Tension is equally distributed among all

More information

COLUMNS: BUCKLING (DIFFERENT ENDS)

COLUMNS: BUCKLING (DIFFERENT ENDS) COLUMNS: BUCKLING (DIFFERENT ENDS) Buckling of Long Straight Columns Example 4 Slide No. 1 A simple pin-connected truss is loaded and supported as shown in Fig. 1. All members of the truss are WT10 43

More information

Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A )

Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A ) Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A23.3-94) Slender Concrete Column Design in Sway Frame Buildings Evaluate slenderness effect for columns in a

More information

Stress Transformation Equations: u = +135 (Fig. a) s x = 80 MPa s y = 0 t xy = 45 MPa. we obtain, cos u + t xy sin 2u. s x = s x + s y.

Stress Transformation Equations: u = +135 (Fig. a) s x = 80 MPa s y = 0 t xy = 45 MPa. we obtain, cos u + t xy sin 2u. s x = s x + s y. 014 Pearson Education, Inc., Upper Saddle River, NJ. All rights reserved. This material is protected under all copyright laws as they currently 9 7. Determine the normal stress and shear stress acting

More information

Introduction to Structural Member Properties

Introduction to Structural Member Properties Introduction to Structural Member Properties Structural Member Properties Moment of Inertia (I): a mathematical property of a cross-section (measured in inches 4 or in 4 ) that gives important information

More information

Failure in Flexure. Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas

Failure in Flexure. Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas MORGAN STATE UNIVERSITY SCHOOL OF ARCHITECTURE AND PLANNING LECTURE VIII Dr. Jason E. Charalambides Failure in Flexure!

More information

Preferred practice on semi-integral abutment layout falls in the following order:

Preferred practice on semi-integral abutment layout falls in the following order: GENERAL INFORMATION: This section of the chapter establishes the practices and requirements necessary for the design and detailing of semi-integral abutments. For general requirements and guidelines on

More information

Part 1 is to be completed without notes, beam tables or a calculator. DO NOT turn Part 2 over until you have completed and turned in Part 1.

Part 1 is to be completed without notes, beam tables or a calculator. DO NOT turn Part 2 over until you have completed and turned in Part 1. NAME CM 3505 Fall 06 Test 2 Part 1 is to be completed without notes, beam tables or a calculator. Part 2 is to be completed after turning in Part 1. DO NOT turn Part 2 over until you have completed and

More information

APPENDIX G I-BEAM SUMMARIES 0.6-IN. STRAND G-1

APPENDIX G I-BEAM SUMMARIES 0.6-IN. STRAND G-1 APPENDIX G I-BEAM SUMMARIES.6-IN. STRAND G-1 Concrete Compressive Strength Embedment Length(L e ) Span Failure Mode Maximum Load Maximum Shear Maximum Moment Maximum Deflection attained Rebound after complete

More information

1. ARRANGEMENT. a. Frame A1-P3. L 1 = 20 m H = 5.23 m L 2 = 20 m H 1 = 8.29 m L 3 = 20 m H 2 = 8.29 m H 3 = 8.39 m. b. Frame P3-P6

1. ARRANGEMENT. a. Frame A1-P3. L 1 = 20 m H = 5.23 m L 2 = 20 m H 1 = 8.29 m L 3 = 20 m H 2 = 8.29 m H 3 = 8.39 m. b. Frame P3-P6 Page 3 Page 4 Substructure Design. ARRANGEMENT a. Frame A-P3 L = 20 m H = 5.23 m L 2 = 20 m H = 8.29 m L 3 = 20 m H 2 = 8.29 m H 3 = 8.39 m b. Frame P3-P6 L = 25 m H 3 = 8.39 m L 2 = 3 m H 4 = 8.5 m L

More information

APPENDIX 1 MODEL CALCULATION OF VARIOUS CODES

APPENDIX 1 MODEL CALCULATION OF VARIOUS CODES 163 APPENDIX 1 MODEL CALCULATION OF VARIOUS CODES A1.1 DESIGN AS PER NORTH AMERICAN SPECIFICATION OF COLD FORMED STEEL (AISI S100: 2007) 1. Based on Initiation of Yielding: Effective yield moment, M n

More information

Designing Reinforced Concrete Rectangular Columns for Biaxial Bending

Designing Reinforced Concrete Rectangular Columns for Biaxial Bending ENGINEERING DATA REORT NUMBER 57 Designing Reinforced Concrete Rectangular Columns for Biaxial Bending A SERVICE OF THE CONCRETE REINFORCING STEEL INSTITUTE 933 N. lum Grove Rd., Schaumburg, Illinois 60173-4758

More information

Chapter (6) Geometric Design of Shallow Foundations

Chapter (6) Geometric Design of Shallow Foundations Chapter (6) Geometric Design of Shallow Foundations Introduction As we stated in Chapter 3, foundations are considered to be shallow if if [D (3 4)B]. Shallow foundations have several advantages: minimum

More information

TORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES)

TORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES) Page1 TORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES) Restrained warping for the torsion of thin-wall open sections is not included in most commonly used frame analysis programs. Almost

More information

SERVICEABILITY LIMIT STATE DESIGN

SERVICEABILITY LIMIT STATE DESIGN CHAPTER 11 SERVICEABILITY LIMIT STATE DESIGN Article 49. Cracking Limit State 49.1 General considerations In the case of verifications relating to Cracking Limit State, the effects of actions comprise

More information

9.5 Compression Members

9.5 Compression Members 9.5 Compression Members This section covers the following topics. Introduction Analysis Development of Interaction Diagram Effect of Prestressing Force 9.5.1 Introduction Prestressing is meaningful when

More information

RETAINING WALL LOADS: Horizontal Equivalent Fluid Pressure = pcf. (Load Case = Soil)

RETAINING WALL LOADS: Horizontal Equivalent Fluid Pressure = pcf. (Load Case = Soil) QuickWall 8.0 - RETAINING WALL ANALYSIS AND DESIGN ================================================================================ Job ID : Job Description : Designed By : ================================================================================

More information

1/29/2010 Page 2 of 65 1/29/2010 Page 3 of 65 1/29/2010 Page 4 of 65 Project Information 1/29/2010 Page 5 of 65 Muckleshoot Indian Tribe Project Number 09-118 West Detention Vault West Vault City of Auburn

More information

Civil Engineering Design (1) Design of Reinforced Concrete Columns 2006/7

Civil Engineering Design (1) Design of Reinforced Concrete Columns 2006/7 Civil Engineering Design (1) Design of Reinforced Concrete Columns 2006/7 Dr. Colin Caprani, Chartered Engineer 1 Contents 1. Introduction... 3 1.1 Background... 3 1.2 Failure Modes... 5 1.3 Design Aspects...

More information

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi Chapter 04 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Compression Members By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering

More information

Chapter 3. Load and Stress Analysis

Chapter 3. Load and Stress Analysis Chapter 3 Load and Stress Analysis 2 Shear Force and Bending Moments in Beams Internal shear force V & bending moment M must ensure equilibrium Fig. 3 2 Sign Conventions for Bending and Shear Fig. 3 3

More information

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich

UNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST

More information

ALUMINUM STRUCTURAL PLATE HEADWALLS AASHTO LRFD BASIS OF DESIGN

ALUMINUM STRUCTURAL PLATE HEADWALLS AASHTO LRFD BASIS OF DESIGN ALUMINUM STRUCTURAL PLATE EADWALLS AASTO LRFD BASIS OF DESIGN LANE ENTERPRISES, INC. www.lane-enterprises.com Required Backfill and Load Cases: ALUMINUM STRUCTURAL PLATE EADWALLS BASIS OF DESIGN Backfill

More information

Accordingly, the nominal section strength [resistance] for initiation of yielding is calculated by using Equation C-C3.1.

Accordingly, the nominal section strength [resistance] for initiation of yielding is calculated by using Equation C-C3.1. C3 Flexural Members C3.1 Bending The nominal flexural strength [moment resistance], Mn, shall be the smallest of the values calculated for the limit states of yielding, lateral-torsional buckling and distortional

More information

APRIL Conquering the FE & PE exams Formulas, Examples & Applications. Topics covered in this month s column:

APRIL Conquering the FE & PE exams Formulas, Examples & Applications. Topics covered in this month s column: APRIL 2015 DR. Z s CORNER Conquering the FE & PE exams Formulas, Examples & Applications Topics covered in this month s column: PE Exam Specifications (Geotechnical) Transportation (Horizontal Curves)

More information

Internal Internal Forces Forces

Internal Internal Forces Forces Internal Forces ENGR 221 March 19, 2003 Lecture Goals Internal Force in Structures Shear Forces Bending Moment Shear and Bending moment Diagrams Internal Forces and Bending The bending moment, M. Moment

More information

Edward C. Robison, PE, SE. 02 January Architectural Metal Works ATTN: Sean Wentworth th ST Emeryville, CA 94608

Edward C. Robison, PE, SE. 02 January Architectural Metal Works ATTN: Sean Wentworth th ST Emeryville, CA 94608 Edward C. Robison, PE, SE ks ATTN: Sean Wentworth 1483 67 th ST Emeryville, CA 94608 02 January 2013 SUBJ: 501 CORTE MADERA AVE, CORTE MADERA, CA 94925 BALCONY GUARD BASE PLATE MOUNTS The guards for the

More information

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi

Karbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi Chapter 05 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Beams By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering 71 Introduction

More information

ERRATA for PE Civil Structural Practice Exam ISBN Copyright 2014 (July 2016 Second Printing) Errata posted

ERRATA for PE Civil Structural Practice Exam ISBN Copyright 2014 (July 2016 Second Printing) Errata posted Errata posted 8-16-2017 Revisions are shown in red. Question 521, p. 47: Question 521 should read as follows: 521. The W10 22 steel eam (Fy = 50 ksi) shown in the figure is only raced at the center of

More information

FIXED BEAMS IN BENDING

FIXED BEAMS IN BENDING FIXED BEAMS IN BENDING INTRODUCTION Fixed or built-in beams are commonly used in building construction because they possess high rigidity in comparison to simply supported beams. When a simply supported

More information

It s a bird it s a plane it s Super Table! F y = 50 ksi F u = 65 ksi ASD LRFD ASD LRFD

It s a bird it s a plane it s Super Table! F y = 50 ksi F u = 65 ksi ASD LRFD ASD LRFD It s a bird it s a plane it s Super Table! steelwise ONE-STOP SHOP BY ABBAS AMINMANSOUR, PhD WHAT IF THERE WAS a table that could be directly used for designing tension members, compression members, flexural

More information

CHAPTER 6: ULTIMATE LIMIT STATE

CHAPTER 6: ULTIMATE LIMIT STATE CHAPTER 6: ULTIMATE LIMIT STATE 6.1 GENERAL It shall be in accordance with JSCE Standard Specification (Design), 6.1. The collapse mechanism in statically indeterminate structures shall not be considered.

More information

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - RC Two Way Spanning Slab XX

Job No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - RC Two Way Spanning Slab XX CONSULTING Engineering Calculation Sheet E N G I N E E R S Consulting Engineers jxxx 1 Material Properties Characteristic strength of concrete, f cu ( 60N/mm 2 ; HSC N/A) 35 N/mm 2 OK Yield strength of

More information

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC.

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC. ICC ES Report ICC ES () 7 () www.icc es.org Most Widely Accepted and Trusted ESR 1 Reissued /1 This report is subject to renewal /. DIVISION: METALS SECTION: METAL FASTENINGS SECTION: 1 STEEL ING REPORT

More information

Problem 7.1 Determine the soil pressure distribution under the footing. Elevation. Plan. M 180 e 1.5 ft P 120. (a) B= L= 8 ft L e 1.5 ft 1.

Problem 7.1 Determine the soil pressure distribution under the footing. Elevation. Plan. M 180 e 1.5 ft P 120. (a) B= L= 8 ft L e 1.5 ft 1. Problem 7.1 Determine the soil pressure distribution under the footing. Elevation Plan M 180 e 1.5 ft P 10 (a) B= L= 8 ft L e 1.5 ft 1.33 ft 6 1 q q P 6 (P e) 180 6 (180) 4.9 kip/ft B L B L 8(8) 8 3 P

More information

Direct Design Method and Design Diagram. For Reinforced Concrete Columns and Shear walls

Direct Design Method and Design Diagram. For Reinforced Concrete Columns and Shear walls Direct Design Method and Design Diagram For Reinforced Concrete Columns and Shear walls BY MAJID HOUSHIAR B.S., Isfahan University of Technology, 1988 M.S., University of Illinois at Chicago, Chicago,

More information

STRUCTURAL ANALYSIS CHAPTER 2. Introduction

STRUCTURAL ANALYSIS CHAPTER 2. Introduction CHAPTER 2 STRUCTURAL ANALYSIS Introduction The primary purpose of structural analysis is to establish the distribution of internal forces and moments over the whole part of a structure and to identify

More information

Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3.

Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3. ES230 STRENGTH OF MTERILS Exam 3 Study Guide Exam 3: Wednesday, March 8 th in-class Updated 3/3/17 Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on

More information

FINITE ELEMENT ANALYSIS OF ARKANSAS TEST SERIES PILE #2 USING OPENSEES (WITH LPILE COMPARISON)

FINITE ELEMENT ANALYSIS OF ARKANSAS TEST SERIES PILE #2 USING OPENSEES (WITH LPILE COMPARISON) FINITE ELEMENT ANALYSIS OF ARKANSAS TEST SERIES PILE #2 USING OPENSEES (WITH LPILE COMPARISON) Ahmed Elgamal and Jinchi Lu October 07 Introduction In this study, we conduct a finite element simulation

More information

Rigid Pavement Mechanics. Curling Stresses

Rigid Pavement Mechanics. Curling Stresses Rigid Pavement Mechanics Curling Stresses Major Distress Conditions Cracking Bottom-up transverse cracks Top-down transverse cracks Longitudinal cracks Corner breaks Punchouts (CRCP) 2 Major Distress Conditions

More information

CHAPTER 4. ANALYSIS AND DESIGN OF COLUMNS

CHAPTER 4. ANALYSIS AND DESIGN OF COLUMNS 4.1. INTRODUCTION CHAPTER 4. ANALYSIS AND DESIGN OF COLUMNS A column is a vertical structural member transmitting axial compression loads with or without moments. The cross sectional dimensions of a column

More information

A Simply supported beam with a concentrated load at mid-span: Loading Stages

A Simply supported beam with a concentrated load at mid-span: Loading Stages A Simply supported beam with a concentrated load at mid-span: Loading Stages P L/2 L PL/4 MOMNT F b < 1 lastic F b = 2 lastic F b = 3 lastoplastic 4 F b = Plastic hinge Plastic Dr. M.. Haque, P.. (LRFD:

More information

3.2 Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups:

3.2 Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups: Sabah Shawkat Cabinet of Structural Engineering 017 3. Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups: (1) slabs supported on edges of

More information

twenty one concrete construction: materials & beams ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2014

twenty one concrete construction: materials & beams ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2014 ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2014 lecture twenty one concrete construction: http:// nisee.berkeley.edu/godden materials & beams Concrete Beams

More information

Chapter 7: Bending and Shear in Simple Beams

Chapter 7: Bending and Shear in Simple Beams Chapter 7: Bending and Shear in Simple Beams Introduction A beam is a long, slender structural member that resists loads that are generally applied transverse (perpendicular) to its longitudinal axis.

More information

Load Capacity Evaluation of Pennsylvania s Single Span T-Beam Bridges

Load Capacity Evaluation of Pennsylvania s Single Span T-Beam Bridges Presentation at 2003 TRB Meeting, Washington, D.C. UNIVERSITY Load Capacity Evaluation of Pennsylvania s Single Span T-Beam Bridges F. N. Catbas, A. E. Aktan, K. Ciloglu, O. Hasancebi, J. S. Popovics Drexel

More information

Design of Reinforced Concrete Structures (II)

Design of Reinforced Concrete Structures (II) Design of Reinforced Concrete Structures (II) Discussion Eng. Mohammed R. Kuheil Review The thickness of one-way ribbed slabs After finding the value of total load (Dead and live loads), the elements are

More information

Properties of Sections

Properties of Sections ARCH 314 Structures I Test Primer Questions Dr.-Ing. Peter von Buelow Properties of Sections 1. Select all that apply to the characteristics of the Center of Gravity: A) 1. The point about which the body

More information

By Dr. Mohammed Ramidh

By Dr. Mohammed Ramidh Engineering Materials Design Lecture.6 the design of beams By Dr. Mohammed Ramidh 6.1 INTRODUCTION Finding the shear forces and bending moments is an essential step in the design of any beam. we usually

More information

Plastic design of continuous beams

Plastic design of continuous beams Budapest University of Technology and Economics Department of Mechanics, Materials and Structures English courses Reinforced Concrete Structures Code: BMEEPSTK601 Lecture no. 4: Plastic design of continuous

More information

EUROCODE EN SEISMIC DESIGN OF BRIDGES

EUROCODE EN SEISMIC DESIGN OF BRIDGES Brussels, 18-20 February 2008 Dissemination of information workshop 1 EUROCODE EN1998-2 SEISMIC DESIGN OF BRIDGES Basil Kolias Basic Requirements Brussels, 18-20 February 2008 Dissemination of information

More information