Chapter 8: Converter Transfer Functions

Size: px
Start display at page:

Download "Chapter 8: Converter Transfer Functions"

Transcription

1 Chapter 8. Converter Transer Functions 8.1. Review o Bode plots Single pole response Single zero response Right hal-plane zero Frequency inversion Combinations Double pole response: resonance The low-q approximation Approximate roots o an arbitrary-degree polynomial 8.2. Analysis o converter transer unctions Example: transer unctions o the buck-boost converter Transer unctions o some basic CCM converters Physical origins o the right hal-plane zero in converters 1

2 Converter Transer Functions 8.3. Graphical construction o converter transer unctions Series impedances: addition o asymptotes Parallel impedances: inverse addition o asymptotes Another example Voltage divider transer unctions: division o asymptotes 8.4. Measurement o ac transer unctions and impedances 8.5. Summary o key points 2

3 The Engineering Design Process 1. Speciications and other design goals are deined. 2. A circuit is proposed. This is a creative process that draws on the physical insight and experience o the engineer. 3. The circuit is modeled. The converter power stage is modeled as described in Chapter 7. Components and other portions o the system are modeled as appropriate, oten with vendor-supplied data. 4. Design-oriented analysis o the circuit is perormed. This involves development o equations that allow element values to be chosen such that speciications and design goals are met. In addition, it may be necessary or the engineer to gain additional understanding and physical insight into the circuit behavior, so that the design can be improved by adding elements to the circuit or by changing circuit connections. 5. Model veriication. Predictions o the model are compared to a laboratory prototype, under nominal operating conditions. The model is reined as necessary, so that the model predictions agree with laboratory measurements. 3

4 Design Process 6. Worst-case analysis (or other reliability and production yield analysis) o the circuit is perormed. This involves quantitative evaluation o the model perormance, to judge whether speciications are met under all conditions. Computer simulation is well-suited to this task. 7. Iteration. The above steps are repeated to improve the design until the worst-case behavior meets speciications, or until the reliability and production yield are acceptably high. This Chapter: steps 4, 5, and 6 4

5 Buck-boost converter model From Chapter 7 L 1 : D D' : 1 Line input i(s) (V g V) d(s) v + g (s) Z in (s) Id(s) Id(s) + C Output + v(s) R Z out (s) d(s) Control input G vg (s)= v(s) v g (s) d(s)=0 G vd (s)= v(s) d(s) vg (s)=0 5

6 Bode plot o control-to-output transer unction with analytical expressions or important eatures 80 dbv G vd G vd G vd 60 dbv 40 dbv 20 dbv 0 dbv 20 dbv G d0 = V DD' 0 10 G vd z /10 D' 2 LC -1/2Q Q = D'R 40 db/decade z D' 2 R 2 DL (RHP) C L V g 2 D'LC DV g (D') 3 RC 20 db/decade dbv 10 1/2Q 10 z Hz 100 Hz 1 khz 10 khz 100 khz MHz 6

7 Design-oriented analysis How to approach a real (and hence, complicated) system Problems: Complicated derivations Long equations Algebra mistakes Design objectives: Obtain physical insight which leads engineer to synthesis o a good design Obtain simple equations that can be inverted, so that element values can be chosen to obtain desired behavior. Equations that cannot be inverted are useless or design! Design-oriented analysis is a structured approach to analysis, which attempts to avoid the above problems 7

8 Some elements o design-oriented analysis, discussed in this chapter Writing transer unctions in normalized orm, to directly expose salient eatures Obtaining simple analytical expressions or asymptotes, corner requencies, and other salient eatures, allows element values to be selected such that a given desired behavior is obtained Use o inverted poles and zeroes, to reer transer unction gains to the most important asymptote Analytical approximation o roots o high-order polynomials Graphical construction o Bode plots o transer unctions and polynomials, to avoid algebra mistakes approximate transer unctions obtain insight into origins o salient eatures 8

9 8.1. Review o Bode plots Decibels Table 8.1. Expressing magnitudes in decibels G db = 20 log 10 G Actual magnitude Magnitude in db Decibels o quantities having units (impedance example): normalize beore taking log Z db = 20 log 10 Z R base 1/2 6dB 1 0 db 2 6 db 5 = 10/2 20 db 6 db = 14 db 10 20dB 1000 = dB = 60 db 5Ω is equivalent to 14dB with respect to a base impedance o R base = 1Ω, also known as 14dBΩ. 60dBµA is a current 60dB greater than a base current o 1µA, or 1mA. 9

10 Bode plot o n Bode plots are eectively log-log plots, which cause unctions which vary as n to become linear plots. Given: G = n Magnitude in db is G db = 20 log 10 Slope is 20n db/decade n = 20n log 10 Magnitude is 1, or 0dB, at requency = 60dB 40dB 20dB 0dB 20dB 40dB 60dB 20dB/decade 20 db/decade 40dB/decade 40dB/decade n = n = 1 n = 1 n = log scale 10

11 Single pole response Simple R-C example R v + 1 (s) C + v 2 (s) Transer unction is G(s)= v 2(s) v 1 (s) = 1 sc 1 sc + R Express as rational raction: G(s)= 1 1+sRC This coincides with the normalized orm G(s)= 1 1+ s 0 with 0 = 1 RC 11

12 G(jω) and G(jω) Let s = jω: G(j )= 1 1+j = 1 j Magnitude is G(j ) = Re (G(j )) 2 + Im (G(j )) 2 = Im(G(j )) G(j ) G(j ) G(j ) Re(G(j )) Magnitude in db: G(j ) db = 20 log db 12

13 Asymptotic behavior: low requency For small requency, ω << ω 0 and << : 0 << 1 G(j ) db G(j ) = Then G(jω) becomes Or, in db, G(j ) 1 1 =1 0dB 20dB 40dB 0dB 20dB/decade 1 G(j ) db 0dB 60dB This is the low-requency asymptote o G(jω) 13

14 Asymptotic behavior: high requency For high requency, ω >> ω 0 and >> : 0 >> G(j ) db 0dB 0dB G(j ) = Then G(jω) becomes G(j ) = 1 20dB 40dB 60dB 20dB/decade The high-requency asymptote o G(jω) varies as -1. Hence, n = -1, and a straight-line asymptote having a slope o -20dB/decade is obtained. The asymptote has a value o 1 at =. 14

15 Deviation o exact curve near = Evaluate exact magnitude: at = : G(j 0 ) = = 1 2 G(j 0 ) db = 20 log db at = 0.5 and 2 : Similar arguments show that the exact curve lies 1dB below the asymptotes. 15

16 Summary: magnitude G(j ) db 0dB 10dB 20dB 1dB 3dB 0.5 1dB 2 20dB/decade 30dB 16

17 Phase o G(jω) Im(G(j )) G(j ) G(j ) G(j ) Re(G(j )) G(j )= 1 1+j = 1 j G(j )= tan 1 0 G(j )=tan 1 Im G(j ) Re G(j ) 17

18 Phase o G(jω) G(j ) 0 0 asymptote G(j )= tan ω G(jω) asymptote ω

19 Phase asymptotes Low requency: 0 High requency: 90 Low- and high-requency asymptotes do not intersect Hence, need a midrequency asymptote Try a midrequency asymptote having slope identical to actual slope at the corner requency. One can show that the asymptotes then intersect at the break requencies a = e /2 / 4.81 b = e /

20 Phase asymptotes G(j ) 0-15 a = / 4.81 a = e /2 / 4.81 b = e / b =

21 Phase asymptotes: a simpler choice G(j ) 0-15 a = / 10 a = / 10 b = b =

22 Summary: Bode plot o real pole 0dB G(j ) db 1dB 3dB 0.5 1dB G(s)= 1 1+ s dB/decade G(j ) 0 / /decade

Chapter 8: Converter Transfer Functions

Chapter 8: Converter Transfer Functions Chapter 8. Converter Transfer Functions 8.1. Review of Bode plots 8.1.1. Single pole response 8.1.2. Single zero response 8.1.3. Right half-plane zero 8.1.4. Frequency inversion 8.1.5. Combinations 8.1.6.

More information

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 8.1. Review of Bode plots Decibels Table 8.1. Expressing magnitudes in decibels G db = 0 log 10

More information

8.1.6 Quadratic pole response: resonance

8.1.6 Quadratic pole response: resonance 8.1.6 Quadratic pole response: resonance Example G(s)= v (s) v 1 (s) = 1 1+s L R + s LC L + Second-order denominator, of the form 1+a 1 s + a s v 1 (s) + C R Two-pole low-pass filter example v (s) with

More information

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder . W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 8.1.7. The low-q approximation Given a second-order denominator polynomial, of the form G(s)= 1

More information

Asymptote. 2 Problems 2 Methods

Asymptote. 2 Problems 2 Methods Asymptote Problems Methods Problems Assume we have the ollowing transer unction which has a zero at =, a pole at = and a pole at =. We are going to look at two problems: problem is where >> and problem

More information

Chapter 9: Controller design

Chapter 9: Controller design Chapter 9. Controller Design 9.1. Introduction 9.2. Effect of negative feedback on the network transfer functions 9.2.1. Feedback reduces the transfer function from disturbances to the output 9.2.2. Feedback

More information

Lecture 47 Switch Mode Converter Transfer Functions: Tvd(s) and Tvg(s) A. Guesstimating Roots of Complex Polynomials( this section is optional)

Lecture 47 Switch Mode Converter Transfer Functions: Tvd(s) and Tvg(s) A. Guesstimating Roots of Complex Polynomials( this section is optional) Lecture 47 Switch Mode Converter Transfer Functions: T vd (s) and T vg (s) A. Guesstimating Roots of Complex Polynomials( this section is optional). Quick Insight n=. n th order case. Cuk example 4. Forth

More information

Chapter 11 AC and DC Equivalent Circuit Modeling of the Discontinuous Conduction Mode

Chapter 11 AC and DC Equivalent Circuit Modeling of the Discontinuous Conduction Mode Chapter 11 AC and DC Equivalent Circuit Modeling of the Discontinuous Conduction Mode Introduction 11.1. DCM Averaged Switch Model 11.2. Small-Signal AC Modeling of the DCM Switch Network 11.3. High-Frequency

More information

CHAPTER 7 : BODE PLOTS AND GAIN ADJUSTMENTS COMPENSATION

CHAPTER 7 : BODE PLOTS AND GAIN ADJUSTMENTS COMPENSATION CHAPTER 7 : BODE PLOTS AND GAIN ADJUSTMENTS COMPENSATION Objectives Students should be able to: Draw the bode plots for first order and second order system. Determine the stability through the bode plots.

More information

Response to a pure sinusoid

Response to a pure sinusoid Harvard University Division of Engineering and Applied Sciences ES 145/215 - INTRODUCTION TO SYSTEMS ANALYSIS WITH PHYSIOLOGICAL APPLICATIONS Fall Lecture 14: The Bode Plot Response to a pure sinusoid

More information

Dynamic circuits: Frequency domain analysis

Dynamic circuits: Frequency domain analysis Electronic Circuits 1 Dynamic circuits: Contents Free oscillation and natural frequency Transfer functions Frequency response Bode plots 1 System behaviour: overview 2 System behaviour : review solution

More information

Lecture 46 Bode Plots of Transfer Functions:II A. Low Q Approximation for Two Poles w o

Lecture 46 Bode Plots of Transfer Functions:II A. Low Q Approximation for Two Poles w o Lecture 46 Bode Plots of Transfer Functions:II A. Low Q Approximation for Two Poles w o ----------- ----------- w L =Q - w o πf o w h =Qw o w L ~ RC w h w L f(l) w h f(c) B. Construction from T(s) Asymptotes

More information

Frequency Response. Re ve jφ e jωt ( ) where v is the amplitude and φ is the phase of the sinusoidal signal v(t). ve jφ

Frequency Response. Re ve jφ e jωt ( ) where v is the amplitude and φ is the phase of the sinusoidal signal v(t). ve jφ 27 Frequency Response Before starting, review phasor analysis, Bode plots... Key concept: small-signal models for amplifiers are linear and therefore, cosines and sines are solutions of the linear differential

More information

Steady State Frequency Response Using Bode Plots

Steady State Frequency Response Using Bode Plots School of Engineering Department of Electrical and Computer Engineering 332:224 Principles of Electrical Engineering II Laboratory Experiment 3 Steady State Frequency Response Using Bode Plots 1 Introduction

More information

Philadelphia University Faculty of Engineering Communication and Electronics Engineering

Philadelphia University Faculty of Engineering Communication and Electronics Engineering Module: Electronics II Module Number: 6503 Philadelphia University Faculty o Engineering Communication and Electronics Engineering Ampliier Circuits-II BJT and FET Frequency Response Characteristics: -

More information

Solution: K m = R 1 = 10. From the original circuit, Z L1 = jωl 1 = j10 Ω. For the scaled circuit, L 1 = jk m ωl 1 = j10 10 = j100 Ω, Z L

Solution: K m = R 1 = 10. From the original circuit, Z L1 = jωl 1 = j10 Ω. For the scaled circuit, L 1 = jk m ωl 1 = j10 10 = j100 Ω, Z L Problem 9.9 Circuit (b) in Fig. P9.9 is a scaled version of circuit (a). The scaling process may have involved magnitude or frequency scaling, or both simultaneously. If R = kω gets scaled to R = kω, supply

More information

Control Systems I. Lecture 9: The Nyquist condition

Control Systems I. Lecture 9: The Nyquist condition Control Systems I Lecture 9: The Nyquist condition adings: Guzzella, Chapter 9.4 6 Åstrom and Murray, Chapter 9.1 4 www.cds.caltech.edu/~murray/amwiki/index.php/first_edition Emilio Frazzoli Institute

More information

Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers.

Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers. Single-Time-Constant (STC) Circuits This lecture is given as a background that will be needed to determine the frequency response of the amplifiers. Objectives To analyze and understand STC circuits with

More information

Frequency response. Pavel Máša - XE31EO2. XE31EO2 Lecture11. Pavel Máša - XE31EO2 - Frequency response

Frequency response. Pavel Máša - XE31EO2. XE31EO2 Lecture11. Pavel Máša - XE31EO2 - Frequency response Frequency response XE3EO2 Lecture Pavel Máša - Frequency response INTRODUCTION Frequency response describe frequency dependence of output to input voltage magnitude ratio and its phase shift as a function

More information

Chapter 9: Controller design. Controller design. Controller design

Chapter 9: Controller design. Controller design. Controller design Chapter 9. Controller Deign 9.. Introduction 9.2. Eect o negative eedback on the network traner unction 9.2.. Feedback reduce the traner unction rom diturbance to the output 9.2.2. Feedback caue the traner

More information

1 (s + 3)(s + 2)(s + a) G(s) = C(s) = K P + K I

1 (s + 3)(s + 2)(s + a) G(s) = C(s) = K P + K I MAE 43B Linear Control Prof. M. Krstic FINAL June 9, Problem. ( points) Consider a plant in feedback with the PI controller G(s) = (s + 3)(s + )(s + a) C(s) = K P + K I s. (a) (4 points) For a given constant

More information

ESE319 Introduction to Microelectronics Bode Plot Review High Frequency BJT Model

ESE319 Introduction to Microelectronics Bode Plot Review High Frequency BJT Model Bode Plot Review High Frequency BJT Model 1 Logarithmic Frequency Response Plots (Bode Plots) Generic form of frequency response rational polynomial, where we substitute jω for s: H s=k sm a m 1 s m 1

More information

Review of Linear Time-Invariant Network Analysis

Review of Linear Time-Invariant Network Analysis D1 APPENDIX D Review of Linear Time-Invariant Network Analysis Consider a network with input x(t) and output y(t) as shown in Figure D-1. If an input x 1 (t) produces an output y 1 (t), and an input x

More information

ECE 255, Frequency Response

ECE 255, Frequency Response ECE 255, Frequency Response 19 April 2018 1 Introduction In this lecture, we address the frequency response of amplifiers. This was touched upon briefly in our previous lecture in Section 7.5 of the textbook.

More information

Part IB Paper 6: Information Engineering LINEAR SYSTEMS AND CONTROL. Glenn Vinnicombe HANDOUT 4. The Frequency ResponseG(jω)

Part IB Paper 6: Information Engineering LINEAR SYSTEMS AND CONTROL. Glenn Vinnicombe HANDOUT 4. The Frequency ResponseG(jω) Part IB Paper 6: Information Engineering LINEAR SYSEMS AND CONROL Glenn Vinnicombe HANDOU 4 he Frequency ResponseG(jω) x(t) 2π ω y(t) G(jω) argg(jω) ω t t Asymptotically stable LI systemg(s) x(t)=cos(ωt)

More information

Frequency methods for the analysis of feedback systems. Lecture 6. Loop analysis of feedback systems. Nyquist approach to study stability

Frequency methods for the analysis of feedback systems. Lecture 6. Loop analysis of feedback systems. Nyquist approach to study stability Lecture 6. Loop analysis of feedback systems 1. Motivation 2. Graphical representation of frequency response: Bode and Nyquist curves 3. Nyquist stability theorem 4. Stability margins Frequency methods

More information

UNIVERSITY OF CALIFORNIA AT BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences. EE105 Lab Experiments

UNIVERSITY OF CALIFORNIA AT BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences. EE105 Lab Experiments UNIVERSITY OF CALIFORNIA AT BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences EE15 Lab Experiments Bode Plot Tutorial Contents 1 Introduction 1 2 Bode Plots Basics

More information

Refinements to Incremental Transistor Model

Refinements to Incremental Transistor Model Refinements to Incremental Transistor Model This section presents modifications to the incremental models that account for non-ideal transistor behavior Incremental output port resistance Incremental changes

More information

ROOT LOCUS. Consider the system. Root locus presents the poles of the closed-loop system when the gain K changes from 0 to. H(s) H ( s) = ( s)

ROOT LOCUS. Consider the system. Root locus presents the poles of the closed-loop system when the gain K changes from 0 to. H(s) H ( s) = ( s) C1 ROOT LOCUS Consider the system R(s) E(s) C(s) + K G(s) - H(s) C(s) R(s) = K G(s) 1 + K G(s) H(s) Root locus presents the poles of the closed-loop system when the gain K changes from 0 to 1+ K G ( s)

More information

Homework 7 - Solutions

Homework 7 - Solutions Homework 7 - Solutions Note: This homework is worth a total of 48 points. 1. Compensators (9 points) For a unity feedback system given below, with G(s) = K s(s + 5)(s + 11) do the following: (c) Find the

More information

1 (20 pts) Nyquist Exercise

1 (20 pts) Nyquist Exercise EE C128 / ME134 Problem Set 6 Solution Fall 2011 1 (20 pts) Nyquist Exercise Consider a close loop system with unity feedback. For each G(s), hand sketch the Nyquist diagram, determine Z = P N, algebraically

More information

Radar Dish. Armature controlled dc motor. Inside. θ r input. Outside. θ D output. θ m. Gearbox. Control Transmitter. Control. θ D.

Radar Dish. Armature controlled dc motor. Inside. θ r input. Outside. θ D output. θ m. Gearbox. Control Transmitter. Control. θ D. Radar Dish ME 304 CONTROL SYSTEMS Mechanical Engineering Department, Middle East Technical University Armature controlled dc motor Outside θ D output Inside θ r input r θ m Gearbox Control Transmitter

More information

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Discussion 5A

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Discussion 5A EECS 6B Designing Information Devices and Systems II Fall 208 Elad Alon and Miki Lustig Discussion 5A Transfer Function When we write the transfer function of an arbitrary circuit, it always takes the

More information

ELECTRONICS & COMMUNICATIONS DEP. 3rd YEAR, 2010/2011 CONTROL ENGINEERING SHEET 5 Lead-Lag Compensation Techniques

ELECTRONICS & COMMUNICATIONS DEP. 3rd YEAR, 2010/2011 CONTROL ENGINEERING SHEET 5 Lead-Lag Compensation Techniques CAIRO UNIVERSITY FACULTY OF ENGINEERING ELECTRONICS & COMMUNICATIONS DEP. 3rd YEAR, 00/0 CONTROL ENGINEERING SHEET 5 Lead-Lag Compensation Techniques [] For the following system, Design a compensator such

More information

Overview of Bode Plots Transfer function review Piece-wise linear approximations First-order terms Second-order terms (complex poles & zeros)

Overview of Bode Plots Transfer function review Piece-wise linear approximations First-order terms Second-order terms (complex poles & zeros) Overview of Bode Plots Transfer function review Piece-wise linear approximations First-order terms Second-order terms (complex poles & zeros) J. McNames Portland State University ECE 222 Bode Plots Ver.

More information

EE221 Circuits II. Chapter 14 Frequency Response

EE221 Circuits II. Chapter 14 Frequency Response EE22 Circuits II Chapter 4 Frequency Response Frequency Response Chapter 4 4. Introduction 4.2 Transfer Function 4.3 Bode Plots 4.4 Series Resonance 4.5 Parallel Resonance 4.6 Passive Filters 4.7 Active

More information

IFB270 Advanced Electronic Circuits

IFB270 Advanced Electronic Circuits IFB270 Advanced Electronic Circuits Chapter 0: Ampliier requency response Pro. Manar Mohaisen Department o EEC Engineering Review o the Precedent Lecture Reviewed o the JFET and MOSFET Explained and analyzed

More information

Boise State University Department of Electrical Engineering ECE461 Control Systems. Control System Design in the Frequency Domain

Boise State University Department of Electrical Engineering ECE461 Control Systems. Control System Design in the Frequency Domain Boise State University Department of Electrical Engineering ECE6 Control Systems Control System Design in the Frequency Domain Situation: Consider the following block diagram of a type- servomechanism:

More information

ROBUST STABILITY AND PERFORMANCE ANALYSIS OF UNSTABLE PROCESS WITH DEAD TIME USING Mu SYNTHESIS

ROBUST STABILITY AND PERFORMANCE ANALYSIS OF UNSTABLE PROCESS WITH DEAD TIME USING Mu SYNTHESIS ROBUST STABILITY AND PERFORMANCE ANALYSIS OF UNSTABLE PROCESS WITH DEAD TIME USING Mu SYNTHESIS I. Thirunavukkarasu 1, V. I. George 1, G. Saravana Kumar 1 and A. Ramakalyan 2 1 Department o Instrumentation

More information

EE221 Circuits II. Chapter 14 Frequency Response

EE221 Circuits II. Chapter 14 Frequency Response EE22 Circuits II Chapter 4 Frequency Response Frequency Response Chapter 4 4. Introduction 4.2 Transfer Function 4.3 Bode Plots 4.4 Series Resonance 4.5 Parallel Resonance 4.6 Passive Filters 4.7 Active

More information

ESE319 Introduction to Microelectronics. Feedback Basics

ESE319 Introduction to Microelectronics. Feedback Basics Feedback Basics Stability Feedback concept Feedback in emitter follower One-pole feedback and root locus Frequency dependent feedback and root locus Gain and phase margins Conditions for closed loop stability

More information

(amperes) = (coulombs) (3.1) (seconds) Time varying current. (volts) =

(amperes) = (coulombs) (3.1) (seconds) Time varying current. (volts) = 3 Electrical Circuits 3. Basic Concepts Electric charge coulomb of negative change contains 624 0 8 electrons. Current ampere is a steady flow of coulomb of change pass a given point in a conductor in

More information

2nd-order filters. EE 230 second-order filters 1

2nd-order filters. EE 230 second-order filters 1 nd-order filters Second order filters: Have second order polynomials in the denominator of the transfer function, and can have zeroth-, first-, or second-order polyinomials in the numerator. Use two reactive

More information

Frequency Response part 2 (I&N Chap 12)

Frequency Response part 2 (I&N Chap 12) Frequency Response part 2 (I&N Chap 12) Introduction & TFs Decibel Scale & Bode Plots Resonance Scaling Filter Networks Applications/Design Frequency response; based on slides by J. Yan Slide 3.1 Example

More information

Sophomore Physics Laboratory (PH005/105)

Sophomore Physics Laboratory (PH005/105) CALIFORNIA INSTITUTE OF TECHNOLOGY PHYSICS MATHEMATICS AND ASTRONOMY DIVISION Sophomore Physics Laboratory (PH5/15) Analog Electronics Active Filters Copyright c Virgínio de Oliveira Sannibale, 23 (Revision

More information

Lecture 6 Classical Control Overview IV. Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science - Bangalore

Lecture 6 Classical Control Overview IV. Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science - Bangalore Lecture 6 Classical Control Overview IV Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science - Bangalore Lead Lag Compensator Design Dr. Radhakant Padhi Asst.

More information

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder Sampled-data response: i L /i c Sampled-data transfer function : î L (s) î c (s) = (1 ) 1 e st

More information

Decibels, Filters, and Bode Plots

Decibels, Filters, and Bode Plots 23 db Decibels, Filters, and Bode Plots 23. LOGAITHMS The use o logarithms in industry is so extensive that a clear understanding o their purpose and use is an absolute necessity. At irst exposure, logarithms

More information

Analog Computing Technique

Analog Computing Technique Analog Computing Technique by obert Paz Chapter Programming Principles and Techniques. Analog Computers and Simulation An analog computer can be used to solve various types o problems. It solves them in

More information

ECE137B Final Exam. There are 5 problems on this exam and you have 3 hours There are pages 1-19 in the exam: please make sure all are there.

ECE137B Final Exam. There are 5 problems on this exam and you have 3 hours There are pages 1-19 in the exam: please make sure all are there. ECE37B Final Exam There are 5 problems on this exam and you have 3 hours There are pages -9 in the exam: please make sure all are there. Do not open this exam until told to do so Show all work: Credit

More information

Microwave Oscillators Design

Microwave Oscillators Design Microwave Oscillators Design Oscillators Classification Feedback Oscillators β Α Oscillation Condition: Gloop = A β(jω 0 ) = 1 Gloop(jω 0 ) = 1, Gloop(jω 0 )=2nπ Negative resistance oscillators Most used

More information

Definitions. Decade: A ten-to-one range of frequency. On a log scale, each 10X change in frequency requires the same distance on the scale.

Definitions. Decade: A ten-to-one range of frequency. On a log scale, each 10X change in frequency requires the same distance on the scale. Circuits II EECS 3220 Lecture notes on making Bode plots Definitions Network Transfer Function: The function H s Xout s X in s where X out represents the voltage or current response of the network to X

More information

EKT 119 ELECTRIC CIRCUIT II. Chapter 3: Frequency Response of AC Circuit Sem2 2015/2016 Dr. Mohd Rashidi Che Beson

EKT 119 ELECTRIC CIRCUIT II. Chapter 3: Frequency Response of AC Circuit Sem2 2015/2016 Dr. Mohd Rashidi Che Beson EKT 9 ELECTRIC CIRCUIT II Chapter 3: Frequency Response of AC Circuit Sem 05/06 Dr. Mohd Rashidi Che Beson TRANSFER FUNCTION (TF Frequency response can be obtained by using transfer function. DEFINITION:

More information

Plan of the Lecture. Goal: wrap up lead and lag control; start looking at frequency response as an alternative methodology for control systems design.

Plan of the Lecture. Goal: wrap up lead and lag control; start looking at frequency response as an alternative methodology for control systems design. Plan of the Lecture Review: design using Root Locus; dynamic compensation; PD and lead control Today s topic: PI and lag control; introduction to frequency-response design method Goal: wrap up lead and

More information

B. T(s) Modification Design Example 1. DC Conditions 2. Open Loop AC Conditions 3. Closed Loop Conditions

B. T(s) Modification Design Example 1. DC Conditions 2. Open Loop AC Conditions 3. Closed Loop Conditions Lecture 51 Tailoring Dynamic Response with Compensation A. Compensation Networks 1. Overview of G c (Alterations and Tailoring) a. Crude Single Pole G C Tailoring b. Elegant Double Pole/Double Zero G C

More information

EE C128 / ME C134 Fall 2014 HW 8 - Solutions. HW 8 - Solutions

EE C128 / ME C134 Fall 2014 HW 8 - Solutions. HW 8 - Solutions EE C28 / ME C34 Fall 24 HW 8 - Solutions HW 8 - Solutions. Transient Response Design via Gain Adjustment For a transfer function G(s) = in negative feedback, find the gain to yield a 5% s(s+2)(s+85) overshoot

More information

Positioning Servo Design Example

Positioning Servo Design Example Positioning Servo Design Example 1 Goal. The goal in this design example is to design a control system that will be used in a pick-and-place robot to move the link of a robot between two positions. Usually

More information

Frequency Response Techniques

Frequency Response Techniques 4th Edition T E N Frequency Response Techniques SOLUTION TO CASE STUDY CHALLENGE Antenna Control: Stability Design and Transient Performance First find the forward transfer function, G(s). Pot: K 1 = 10

More information

Homework Assignment 11

Homework Assignment 11 Homework Assignment Question State and then explain in 2 3 sentences, the advantage of switched capacitor filters compared to continuous-time active filters. (3 points) Continuous time filters use resistors

More information

ECE3050 Assignment 7

ECE3050 Assignment 7 ECE3050 Assignment 7. Sketch and label the Bode magnitude and phase plots for the transfer functions given. Use loglog scales for the magnitude plots and linear-log scales for the phase plots. On the magnitude

More information

1. Design a 3rd order Butterworth low-pass filters having a dc gain of unity and a cutoff frequency, fc, of khz.

1. Design a 3rd order Butterworth low-pass filters having a dc gain of unity and a cutoff frequency, fc, of khz. ECE 34 Experiment 6 Active Filter Design. Design a 3rd order Butterworth low-pass ilters having a dc gain o unity and a cuto requency, c, o.8 khz. c :=.8kHz K:= The transer unction is given on page 7 j

More information

EE348L Lecture 1. EE348L Lecture 1. Complex Numbers, KCL, KVL, Impedance,Steady State Sinusoidal Analysis. Motivation

EE348L Lecture 1. EE348L Lecture 1. Complex Numbers, KCL, KVL, Impedance,Steady State Sinusoidal Analysis. Motivation EE348L Lecture 1 Complex Numbers, KCL, KVL, Impedance,Steady State Sinusoidal Analysis 1 EE348L Lecture 1 Motivation Example CMOS 10Gb/s amplifier Differential in,differential out, 5 stage dccoupled,broadband

More information

Studio Exercise Time Response & Frequency Response 1 st -Order Dynamic System RC Low-Pass Filter

Studio Exercise Time Response & Frequency Response 1 st -Order Dynamic System RC Low-Pass Filter Studio Exercise Time Response & Frequency Response 1 st -Order Dynamic System RC Low-Pass Filter i i in R out Assignment: Perform a Complete e in C e Dynamic System Investigation out of the RC Low-Pass

More information

ET4119 Electronic Power Conversion 2011/2012 Solutions 27 January 2012

ET4119 Electronic Power Conversion 2011/2012 Solutions 27 January 2012 ET4119 Electronic Power Conversion 2011/2012 Solutions 27 January 2012 1. In the single-phase rectifier shown below in Fig 1a., s = 1mH and I d = 10A. The input voltage v s has the pulse waveform shown

More information

Class 13 Frequency domain analysis

Class 13 Frequency domain analysis Class 13 Frequency domain analysis The frequency response is the output of the system in steady state when the input of the system is sinusoidal Methods of system analysis by the frequency response, as

More information

Asymptotic Bode Plot & Lead-Lag Compensator

Asymptotic Bode Plot & Lead-Lag Compensator Asymptotic Bode Plot & Lead-Lag Compensator. Introduction Consider a general transfer function Ang Man Shun 202-2-5 G(s = n k=0 a ks k m k=0 b ks k = A n k=0 (s z k m k=0 (s p k m > n When s =, transfer

More information

Homework Assignment 08

Homework Assignment 08 Homework Assignment 08 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. Give one phrase/sentence that describes the primary advantage of an active load. Answer: Large effective resistance

More information

MICROELECTRONIC CIRCUIT DESIGN Second Edition

MICROELECTRONIC CIRCUIT DESIGN Second Edition MICROELECTRONIC CIRCUIT DESIGN Second Edition Richard C. Jaeger and Travis N. Blalock Answers to Selected Problems Updated 10/23/06 Chapter 1 1.3 1.52 years, 5.06 years 1.5 2.00 years, 6.65 years 1.8 113

More information

( s) N( s) ( ) The transfer function will take the form. = s = 2. giving ωo = sqrt(1/lc) = 1E7 [rad/s] ω 01 := R 1. α 1 2 L 1.

( s) N( s) ( ) The transfer function will take the form. = s = 2. giving ωo = sqrt(1/lc) = 1E7 [rad/s] ω 01 := R 1. α 1 2 L 1. Problem ) RLC Parallel Circuit R L C E-4 E-0 V a. What is the resonant frequency of the circuit? The transfer function will take the form N ( ) ( s) N( s) H s R s + α s + ω s + s + o L LC giving ωo sqrt(/lc)

More information

Lecture 120 Compensation of Op Amps-I (1/30/02) Page ECE Analog Integrated Circuit Design - II P.E. Allen

Lecture 120 Compensation of Op Amps-I (1/30/02) Page ECE Analog Integrated Circuit Design - II P.E. Allen Lecture 20 Compensation of Op AmpsI (/30/02) Page 20 LECTURE 20 COMPENSATION OF OP AMPS I (READING: GHLM 425434 and 624638, AH 249260) INTRODUCTION The objective of this presentation is to present the

More information

Second-order filters. EE 230 second-order filters 1

Second-order filters. EE 230 second-order filters 1 Second-order filters Second order filters: Have second order polynomials in the denominator of the transfer function, and can have zeroth-, first-, or second-order polynomials in the numerator. Use two

More information

Active Control? Contact : Website : Teaching

Active Control? Contact : Website :   Teaching Active Control? Contact : bmokrani@ulb.ac.be Website : http://scmero.ulb.ac.be Teaching Active Control? Disturbances System Measurement Control Controler. Regulator.,,, Aims of an Active Control Disturbances

More information

Electronics II. Final Examination

Electronics II. Final Examination The University of Toledo f6fs_elct7.fm - Electronics II Final Examination Problems Points. 5. 0 3. 5 Total 40 Was the exam fair? yes no The University of Toledo f6fs_elct7.fm - Problem 5 points Given is

More information

Feedback design for the Buck Converter

Feedback design for the Buck Converter Feedback design for the Buck Converter Portland State University Department of Electrical and Computer Engineering Portland, Oregon, USA December 30, 2009 Abstract In this paper we explore two compensation

More information

Decibels, Filters, and Bode Plots

Decibels, Filters, and Bode Plots Decibels, Filters, and Bode Plots 2 Objectives Develop conidence in the use o logarithms and decibels in the description o power and voltage levels. Become amiliar with the requency response o high- and

More information

Chapter 6 Frequency Response, Bode Plots and Resonance

Chapter 6 Frequency Response, Bode Plots and Resonance Chapter 6 Frequency Response, Bode Plots and Resonance Signal Processg is concerned with manipulatg Signals to extract Inormation and to use that ormation to generate other useul Signals Goal. Fundamental

More information

MAE 143B - Homework 9

MAE 143B - Homework 9 MAE 143B - Homework 9 7.1 a) We have stable first-order poles at p 1 = 1 and p 2 = 1. For small values of ω, we recover the DC gain K = lim ω G(jω) = 1 1 = 2dB. Having this finite limit, our straight-line

More information

Laplace Transform Analysis of Signals and Systems

Laplace Transform Analysis of Signals and Systems Laplace Transform Analysis of Signals and Systems Transfer Functions Transfer functions of CT systems can be found from analysis of Differential Equations Block Diagrams Circuit Diagrams 5/10/04 M. J.

More information

Exercise s = 1. cos 60 ± j sin 60 = 0.5 ± j 3/2. = s 2 + s + 1. (s + 1)(s 2 + s + 1) T(jω) = (1 + ω2 )(1 ω 2 ) 2 + ω 2 (1 + ω 2 )

Exercise s = 1. cos 60 ± j sin 60 = 0.5 ± j 3/2. = s 2 + s + 1. (s + 1)(s 2 + s + 1) T(jω) = (1 + ω2 )(1 ω 2 ) 2 + ω 2 (1 + ω 2 ) Exercise 7 Ex: 7. A 0 log T [db] T 0.99 0.9 0.8 0.7 0.5 0. 0 A 0 0. 3 6 0 Ex: 7. A max 0 log.05 0 log 0.95 0.9 db [ ] A min 0 log 40 db 0.0 Ex: 7.3 s + js j Ts k s + 3 + j s + 3 j s + 4 k s + s + 4 + 3

More information

) t 0(q+ t ) dt n t( t) dt ( rre i dq t 0 u = = t l C t) t) a i( ( q tric c le E

) t 0(q+ t ) dt n t( t) dt ( rre i dq t 0 u = = t l C t) t) a i( ( q tric c le E EE70 eview Electrical Current i ( t ) dq ( t ) dt t q ( t ) i ( t ) dt + t 0 q ( t 0 ) Circuit Elements An electrical circuit consists o circuit elements such as voltage sources, resistances, inductances

More information

Chapter 6 - Solved Problems

Chapter 6 - Solved Problems Chapter 6 - Solved Problems Solved Problem 6.. Contributed by - James Welsh, University of Newcastle, Australia. Find suitable values for the PID parameters using the Z-N tuning strategy for the nominal

More information

The achievable limits of operational modal analysis. * Siu-Kui Au 1)

The achievable limits of operational modal analysis. * Siu-Kui Au 1) The achievable limits o operational modal analysis * Siu-Kui Au 1) 1) Center or Engineering Dynamics and Institute or Risk and Uncertainty, University o Liverpool, Liverpool L69 3GH, United Kingdom 1)

More information

Filters and Tuned Amplifiers

Filters and Tuned Amplifiers Filters and Tuned Amplifiers Essential building block in many systems, particularly in communication and instrumentation systems Typically implemented in one of three technologies: passive LC filters,

More information

ECEN 325 Electronics

ECEN 325 Electronics ECEN 325 Electronics Introduction Dr. Aydın İlker Karşılayan Texas A&M University Department of Electrical and Computer Engineering Ohm s Law i R i R v 1 v v 2 v v 1 v 2 v = v 1 v 2 v = v 1 v 2 v = ir

More information

OPERATIONAL AMPLIFIER APPLICATIONS

OPERATIONAL AMPLIFIER APPLICATIONS OPERATIONAL AMPLIFIER APPLICATIONS 2.1 The Ideal Op Amp (Chapter 2.1) Amplifier Applications 2.2 The Inverting Configuration (Chapter 2.2) 2.3 The Non-inverting Configuration (Chapter 2.3) 2.4 Difference

More information

Math-3 Lesson 8-5. Unit 4 review: a) Compositions of functions. b) Linear combinations of functions. c) Inverse Functions. d) Quadratic Inequalities

Math-3 Lesson 8-5. Unit 4 review: a) Compositions of functions. b) Linear combinations of functions. c) Inverse Functions. d) Quadratic Inequalities Math- Lesson 8-5 Unit 4 review: a) Compositions o unctions b) Linear combinations o unctions c) Inverse Functions d) Quadratic Inequalities e) Rational Inequalities 1. Is the ollowing relation a unction

More information

ECE137B Final Exam. Wednesday 6/8/2016, 7:30-10:30PM.

ECE137B Final Exam. Wednesday 6/8/2016, 7:30-10:30PM. ECE137B Final Exam Wednesday 6/8/2016, 7:30-10:30PM. There are7 problems on this exam and you have 3 hours There are pages 1-32 in the exam: please make sure all are there. Do not open this exam until

More information

Homework Assignment 09

Homework Assignment 09 Homework Assignment 09 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =

More information

EE 508 Lecture 4. Filter Concepts/Terminology Basic Properties of Electrical Circuits

EE 508 Lecture 4. Filter Concepts/Terminology Basic Properties of Electrical Circuits EE 58 Lecture 4 Filter Concepts/Terminology Basic Properties of Electrical Circuits Review from Last Time Filter Design Process Establish Specifications - possibly T D (s) or H D (z) - magnitude and phase

More information

EE 40: Introduction to Microelectronic Circuits Spring 2008: Midterm 2

EE 40: Introduction to Microelectronic Circuits Spring 2008: Midterm 2 EE 4: Introduction to Microelectronic Circuits Spring 8: Midterm Venkat Anantharam 3/9/8 Total Time Allotted : min Total Points:. This is a closed book exam. However, you are allowed to bring two pages

More information

BIOEN 302, Section 3: AC electronics

BIOEN 302, Section 3: AC electronics BIOEN 3, Section 3: AC electronics For this section, you will need to have very present the basics of complex number calculus (see Section for a brief overview) and EE5 s section on phasors.. Representation

More information

I. Frequency Response of Voltage Amplifiers

I. Frequency Response of Voltage Amplifiers I. Frequency Response of Voltage Amplifiers A. Common-Emitter Amplifier: V i SUP i OUT R S V BIAS R L v OUT V Operating Point analysis: 0, R s 0, r o --->, r oc --->, R L ---> Find V BIAS such that I C

More information

Poles and Zeros and Transfer Functions

Poles and Zeros and Transfer Functions Poles and Zeros and Transfer Functions Transfer Function: Considerations: Factorization: A transfer function is defined as the ratio of the Laplace transform of the output to the input with all initial

More information

Converter System Modeling via MATLAB/Simulink

Converter System Modeling via MATLAB/Simulink Converter System Modeling via MATLAB/Simulink A powerful environment for system modeling and simulation MATLAB: programming and scripting environment Simulink: block diagram modeling environment that runs

More information

r + - FINAL June 12, 2012 MAE 143B Linear Control Prof. M. Krstic

r + - FINAL June 12, 2012 MAE 143B Linear Control Prof. M. Krstic MAE 43B Linear Control Prof. M. Krstic FINAL June, One sheet of hand-written notes (two pages). Present your reasoning and calculations clearly. Inconsistent etchings will not be graded. Write answers

More information

Frequency Response Analysis

Frequency Response Analysis Frequency Response Analysis Consider let the input be in the form Assume that the system is stable and the steady state response of the system to a sinusoidal inputdoes not depend on the initial conditions

More information

Stability & Compensation

Stability & Compensation Advanced Analog Building Blocks Stability & Compensation Wei SHEN (KIP) 1 Bode Plot real zeros zeros with complex conjugates real poles poles with complex conjugates http://lpsa.swarthmore.edu/bode/bode.html

More information

Frequency Dependent Aspects of Op-amps

Frequency Dependent Aspects of Op-amps Frequency Dependent Aspects of Op-amps Frequency dependent feedback circuits The arguments that lead to expressions describing the circuit gain of inverting and non-inverting amplifier circuits with resistive

More information

EECE 301 Signals & Systems Prof. Mark Fowler

EECE 301 Signals & Systems Prof. Mark Fowler EECE 301 Signals & Systems Prof. Mark Fowler C-T Systems: Bode Plots Note Set #36 1/14 What are Bode Plots? Bode Plot = Freq. Resp. plotted with H() in db on a log frequency axis. Its easy to use computers

More information

Transient response via gain adjustment. Consider a unity feedback system, where G(s) = 2. The closed loop transfer function is. s 2 + 2ζωs + ω 2 n

Transient response via gain adjustment. Consider a unity feedback system, where G(s) = 2. The closed loop transfer function is. s 2 + 2ζωs + ω 2 n Design via frequency response Transient response via gain adjustment Consider a unity feedback system, where G(s) = ωn 2. The closed loop transfer function is s(s+2ζω n ) T(s) = ω 2 n s 2 + 2ζωs + ω 2

More information