Enhancement of State Estimation Results using Phasor Measurements. Presented to: NASPI Work Group Meeting March 6-7, 2008, New Orleans, LA

Transcription

1 Enhancement of State Estimation Results using Phasor Measurements Presented to: NASPI Work Group Meeting March 6-7, 2008, New Orleans, LA by Lu Kondragunta San Diego Gas & Electric 2008 San Diego Gas & Electric Company. Trademarks belong to their respective owners. All rights reserved.

2 Enhancement of State Estimation Results using Phasor Measurements Disclaimers & Appreciation. This presentation reports the results of a synthesized work based on the dedicated works of various groups of researchers and technologists. There is neither discovery nor innovation in the material to be presented. I express great reverence and admiration to all the great discoverers and scientists, and to the great technologists for their leading the way 2

3 Enhancement of State Estimation Results using Phasor Measurements TOPICS: SDG&E Real Time System Operations The Phasor Project Implementation Testing and Results Conclusions 3

4 SDG&E - Real Time System Operations (RTSO) EMS System SCADA SOD s; Tabular Displays; PI (displays) Transmission Security Management Sub-System in EMS Real Time Network Applications (SE) ; Real Time Contingency Applications; Real Time Voltage Var Scheduling; Real Time Security Constrained Dispatch SE & CA Run every 5 and 10 minutes respectively (on time trigger); 99.9% uptime and convergence. CA :325 contingencies (N-2, Bus, Generator and RAS); 4

5 PHASORS What and Why? PHASORS Phasor - A Concept in Electrical Engineering. Represents a Sinusoid. PMU: Advancements in Microelectronics and Digital Signal Processing measures the magnitude and phase of voltages and currents at a bus. ( V, δ v, I, δ i ) GPS Time Synchronized sampling at very high rates. High rate time synchronized data. 5

6 PHASORS What and Why? (contd.) 6

7 PHASORS - What and Why? (contd.) 7

8 PHASORS Why? PHASORS - Use Utilities in the west installed PMUs for over a decade. Used high rate data for after the fact studies. Helpful to understand the phenomena and physics of the system during the transient states. Not used in Steady State studies. Power System SE computes the phase angle differences in steady state using real power measurements from RTUs. Why Not use the phasor data from the PMUs as additional measurements? (Not the 1st onesthere exists prior work in academic institutions) Can the estimates be improved? 8

9 CIEE PIER/TRP (CEC) PROJECT The Project: Enhancement of State Estimation Results Using Real Time Phasor data (June 2006; Sept. 2006) Co-funded project : California Energy Commission (CEC) CIEE (PIER/TRP) and (SDG&E). Kick off Meeting - March, 2007 SDG&E, CEC, CIEE, EPG, OSIsoft, GE, SEL SEL: Synchro Phasor Processing (SPP / PDC) Unit and associated software. OSIsoft: Software to interface SPP data in IEEE protocol with PI Server GE: Bi-directional Software to Interface PI data with EMS RTDB. EPG: Consultants - RTDMS 9

10 Objective & Goals Objective: Statement of the Problem: To investigate methods to integrate Phasor measurement data into the Power System State Estimator (SE) on the EMS System of SDG&E with a view to improve the quality of the power system state estimates and thus establish a reliable real time database. The project goals: two phases 1. Integrate real-time phasor data for use by State Estimator in order to improve its results (Target completion date: June 30, 2008) 2. Investigate and evaluate methods to use Phasor data and SE results to better manage congestion problems. (Target completion date: June 30, 2009) 10

11 PMU LOCATIONS PDC) N2 S2 X PMU _N2 X RTU Lab X PMU _S2 M2 PMU _M2 X X M5 PMU _M5 I5 N5 H5 T

12 Implementation Architecture - Overview Task 5: Use Phasor Data to Enhance State Estimator EMS Task 6: Measure Performance Improvement of WLS Estimator EMS PI Interface Task 4: Integrate Phasor Data with EMS Data Task 1: Acquire & Deploy PMUs Task 3: Integrate PDC with the PI Server Task 2: Install PDC & Software Historian (PI) C PI Interface Per Standard over Ethernet (UDP or TCP) Concentrator Data Rate: Measurements per Second Task 7: Data Sharing (FUTURE)... 12

13 State Estimation The Reference Bus LF : Accounts for the Slack SE : Meaningful Difference in angle measurements - No need to have Phasor Measurements at the ref. bus - N(N-1)/2 Phase angle difference measurements ( ) ( ) ( ) ε ε ε ε ε + δ δ δ δ δ δ = + ε = N N j i ij j i i j i ij j i j i j i X V V V X V V V V x h z sin sin M M δ δ = j i j i V V x M + = N N ij ij j i Q P V V j z ε ε ε ε ε δ ι M M )] - [( (1.0) )] - [( ) X / V (V P m k km m k km m k km δ δ δ δ δ = = 13

14 Testing The following tests were performed Ensure phasor measurement data availability in SE (Tested Successfully). Verify the validity of phasor measurements within state estimator compare angle differences between measured angles by PMUs and caculated angles in SE for a given timestamp (Tested Successfully). Verify that these measurements can be disabled by the user (Tested Successfully). Verify that weights are appropriately assigned for these measurements and these can be modified - (Tested successfully SE was tested with varying measurement weights). 14

15 Measured Absolute Phase Angles Phase angles measured 15

16 Angle Differences EMS Measurement Buffer 16

17 Test Results - 1 ( ) Test 1,date 12/6/07 Measure measurement ment with phasor Meas without phasor Meas angle Residual angle est Residual Meas w/o estimate residual meas angle est Angle w/o ph Angle phasor estimate MW(line &transf sigmas at Original values), Phasor sigma=0.03 residual w/o ph with phmeas w/o phmes N2 M2 line S2 M2 line 'S2 M2 line M5 M2 Trans = abs((meas est)/meas), No appreciable difference in error% by adding Phasor measurements Test 2, date 12/6/07 Measure measurement ment with phasor Meas SDG&E SE TEST WITH PHASORS FROM 12/6/07 TO 12/7/07 without phasor Meas angle Residual angle est w/o estimate residual meas angle est Angle w/o ph Residual phasor original sigmas for line trans, phasors sigma=0.1, Threshold set to 20 estimate with phmeas w/o phmes N2 M2 line S2 M2 line 'S2 M2 line = abs((meas est)/meas), No appreciable difference in error% by adding Phasor measurements Diff phwph diff 17

18 Test Results -2 ( ) SDG&E SE TEST WITH PHASORS FROM 12/6/07 TO 12/7/07 Test 3, date 12/07/07 measurement Measure angle Residual angle est Residual Meas w/o residual ment estimate residual meas angle est Angle w/o ph Angle phasor estimate w/o ph Relax sigmas(3*sig=full scale value*error%) sig 500=12,sig 230=10,sig 138=5,sig69=4, sigma phasor meas 0.1 with phmeas w/o phmes N2 M2 line S2 M2 line 'S2 M2 line M5 M2 Trans error% improves by adding Phasor measurements Test 4, date 12/07/07 measurement Jph from ph 72 Jwoph Measure angle Residual angle est Residual Meas w/o ment estimate residual meas angle est Angle w/o ph Angle phasor estimate Sigmas as above- RTU's at ML,MS and MX blocked, phasor sigma=0.1 residual w/o ph with phmeas w/o phmes N2 M2 line S2 M2 line 'S2 M2 line M5 M2 Trans error% improves by adding Phasor measurements Test 5, date 12/07/07 measurement with phasor Meas estimate residual with phasor Meas with phasor Meas with phasor Meas without phasor Meas without phasor Meas without phasor Meas angle Residual angle est Residual Meas w/o meas angle est Angle w/o ph Angle phasor MW(line &trans sigma as above Phasor sigma=0.03 estimate residual w/o ph with phmeas w/o phmes N2 M2 line S2 M2 line 'S2 M2 line M5 M2 Trans error% improves by adding Phasor measurements Diff phwph Diff phwph Diff phwph 18

19 Test Results 3 ( ) Angles SE TESTING PMU+ SCADA SCADA PMU NO SCADA&NO PMUS Meas Est %Error Est %Error Est %Error Est %Error M2 - M S2-M S2-M N2-M N2-M N2-S BRANCH FLOWS M2 M2-M5 Bk M2-M5 Bk M2-S2 ln M2-S2 ln N2-M2 ln N2-M2 ln M2-T2 ln S2 M2-S2 ln M2-S2 ln N2 N2-M2 ln N2-M2 ln No PMU Measurements Bus M M S N NO SCADA & NO PMUs Bus M M S N

20 Conclusions 1. The Phasor Measurements were successfully integrated with the SCADA measurements, in a WLS Power System State Estimator. 2. No phasor measurements were made at the reference bus. 3. The phase angle differences are treated as measurements. 4. Regarding accuracy no definite conclusions could be made due to: i. Small number of phasor measurements used; ii. A very stable and accurate WLS estimator used for testing; iii. A marginal improvement in the accuracy of the estimates is noted. 20

21 Acknowledgments &Thanks! California Energy Commission (CEC) Center for Energy and Environment (CIEE) Schweitzer Engineering Laboratories (SEL) OSIsoft General Electric (GE) Electric Power Group (EPG) And, All those whose wisdom contributed to the success of this project (on whose broad shoulders we stand and innovate a little and peep into the future with a hope for a better tomorrow) 21

22 Questions? QUESTIONS? Thank you, all! 22

23 23

24 24