佰鴻工業股份有限公司. DEVICE NUMBER:BWL-8Q5A21-K65 佰鴻工業股份有限公司

Transcription

1 DATA SHEET DEVICE NUMBER: SHEET CONTENTS DATE Preliminary 台北縣板橋市和平路 19 號 3 樓 APPROVED DRAWER 羅劉 3F., No. 19, Ho Ping Road, Pan Chiao City, Taipei, Taiwan, R. O. C. Tel: Fax: / 豐秋曉

2 Features: 1. Constant current supply: 180mA (at 33 V DC, max.) 2. Input power: 5 W. 3. Chip material: InGaN. 4. Emitted color: White. 5. High lumen output. 6. High light output efficiency (lm/w). 7. Excellent thermal management: Self-mounted on Al MCPCB. 8. Easy to be assemblies with heat sink. 9. Long life ( if the temperature of the Al MCPCB (Tb) is kept under 60, by using a suitable heat sink). 10. As a lighting board install, the prepared components bag should be applied. Avoiding the short damage of electrical circuit, insulating washers are required to apply. Please refer to the components assembling demonstration in Page This product do not contain restriced substance, compliance to ROHS standard. Applications: 1. Outdoor Lightings: street light, tunnel light. 2. Indoor Lightings: Recessed can light, suspension ceiling light, wall light. Package dimensions: Notes: 1. All dimensions are in mm[in]. 2. Tolerance is ±0.5[0.02]mm[in] unless otherwise specified. Ver.1.0 Page: 1 of 7

3 Absolute maximum ratings Parameter Symbol Rating Unit DC Input Forward Current * I IN 180 ma Power Dissipation P D 5 W Reverse input voltage Vr 33 V DC ESD HBM 2000 V Storage Temperature Tstg -40~+80 Manual Soldering (T=5 sec) Tsol 300 ± 5 o C Temperature of Al MCPCB Tb 60 * Proper current derating must be followed to keep the temperature of Al MCPCB(Tb) below 60. Electrical & Optical Characteristics (Tb =25 ) Parameter Symbol Condition Min. Typ. Max. Unit Forward Voltage* V F I F =180mA V Total Flux Φ v I F =180mA lm Light Efficient η I F =180mA lm/w Color Temperature CCT I F =180mA K Color Rendering Index CRI I F =180mA Viewing Angle 2θ 1/2 I F =180mA degree Life Time(L 70 ) t at Tb 70-30,000 - hrs * A power supply with maximum constant current source of 180mA is highly recommended. Ver.1.0 Page: 2 of 7

4 Typical electro-optical characteristics curves Rθ =6 /W J-A Rθ =3 /W J-A Rθ =12 /W J-A Ver.1.0 Page: 3 of 7

5 Components Assembling Demonstration: Steps Pictures Instructions Remarks 1 Items to prepare: light source, heat dispersion tape, heat dispersion plate, screws, nuts, washers, electrical wire or wire with connector(optional) Screws, nuts, and washers may be required to firmly attach the heat dispersion module in it's fixed position. 2 Attach the heat dispersion tape on Heat dispersing paste may be the heat dispersion plate at its applied to the back of the fixed and locked position. light source. 3 Apply electrical wires. Two options available: Attach the light source to the heat (1) use wire with connectors dispersion plate. (2) Solder the wires 4 Evenly tighten all screws. Notes: 1. A Components bag is included: M2 ScrewsX2. Failure is possible if force is applied to improperly positioned screws. Ver.1.0 Page: 4 of 7

6 Total Flux Bin Limits (at IF =180mA) BIN CODE Min. (lm) Max. (lm) U V W Tolerance for each Bin limit is ± 3 % Color Temperature Bin Limits (at IF =180mA) ; as specified in ANSI C CIE 1931 x,y Chromaticity Diagram 0.44 y K 57K 50K 45K 40K 35K 30K 27K x BIN CODE Nominal CCT CCT Range K K Chromaticity Coordinates x y BIN: x x Color Temperature BIN CODE Total Flux BIN CODE Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. Ver.1.0 Page: 5 of 7

7 Soldering : 1. Manual Soldering The temperature of the iron tip should not be higher than 300 and Soldering time to be within 3 seconds per solder-pad. Storage: In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as possible after unpacking the sealed envelope. If the envelope is still packed, to store it in the environment as following: (1) Temperature : 5-30 (41 )Humidity : RH 60 % Max. (2) Devices require baking before mounting, if: (3) If baking is required, devices must be baked under below conditions: 48 hours at 60 ±3. Package and Label of Products: (1) Package: Products are packed in one bag of 2 pcs and a label is attached to each bag. (2) Label: BRIGHT LED LOGO Part No. Power Qauntily Sealing dare XXXX XX XX Year Month Day Ver.1.0 Page: 6 of 7

8 Packing(unit: mm[in]): Notes: 1. Dimension:mm[in]. 2. Tolerance:±10[0.4]mm[in]. Ver.1.0 Page: 7 of 7