Balancing of Masses. 1. Balancing of a Single Rotating Mass By a Single Mass Rotating in the Same Plane

Size: px
Start display at page:

Download "Balancing of Masses. 1. Balancing of a Single Rotating Mass By a Single Mass Rotating in the Same Plane"

Transcription

1 lecture - 1 Balancing of Masses Theory of Machine Balancing of Masses A car assembly line. In this chapter we shall discuss the balancing of unbalanced forces caused by rotating masses, in order to minimize the loads on bearings and stresses in the various members, which causes dangerous vibrations when a machine is running. The following cases are important from the subject point of view: 1. Balancing of a single rotating mass by a single mass rotating in the same plane. 2. Balancing of a single rotating mass by two masses rotating in different planes. 3. Balancing of different masses rotating in the same plane. 4. Balancing of different masses rotating in different planes. 1. Balancing of a Single Rotating Mass By a Single Mass Rotating in the Same Plane Consider a disturbing mass m 1 attached to a shaft rotating at ω rad/s as shown in Fig.1. Let r 1 be the radius of rotation of the mass m 1. We know that the centrifugal force exerted by the mass m 1 on the shaft, F Cl = m 1. ω 2. r 1.(1) 1

2 lecture - 1 Balancing of Masses Theory of Machine Fig. 1. Balancing of a single rotating mass by a single mass rotating in the same plane. This centrifugal force produces bending moment on the shaft. In order to counteract the effect of this force, a balancing mass (m 2 ) may be attached in the same plane of rotation as that of disturbing mass ( m 1 ) such that the centrifugal forces due to the two masses are equal and opposite. Let r 2 = Radius of rotation of the balancing mass m 2, centrifugal force due to mass m 2, F C2 = m 2. ω 2. r 2.(2) Equating equations (1) and (2), m 1. ω 2. r 1 = m 2. ω 2. r 2 or m 1. r 1 = m 2. r 2 2. Balancing of a Single Rotating Mass By Two Masses Rotating in Different Planes In order to put the system in complete balance, two balancing masses are placed in two different planes, parallel to the plane of rotation of the disturbing mass, There are two possibilities may arise while attaching the two balancing masses: a) When the plane of the disturbing mass lies in between the planes of the two balancing masses Consider a disturbing mass m balanced by two rotating masses m 1 and m 2 as shown in Fig. 2. Let r, r 1 and r 2 be the radii of rotation of the masses m, m 1 and m 2 respectively. 2

3 lecture - 1 Balancing of Masses Theory of Machine Fig.2. Balancing of a single rotating mass by two rotating masses in different planes when the plane of single rotating mass lies in between the planes of two balancing masses. The net force acting on the shaft must be equal to zero F C = F Cl + F C2 F C : Centrifugal force exerted by the mass m F C1 : Centrifugal force exerted by the mass m 1 F C2 : Centrifugal force exerted by the mass m 2 m. ω 2. r = m 1. ω 2. r 1 + m 2. ω 2. r 2 m. r = m 1. r 1 + m 2. r 2 Now in order to find the magnitude of balancing force at the bearing B of a shaft, take moments about A. Therefore F C1 l = F C l 2 or m 1. ω 2. r 1 l = m. ω 2. r l 2 m 1. r 1 l = m. r l 2 Similarly, in order to find the balancing force at the bearing A of a shaft, take moments about B. Therefore F C2 l = F C l 1 or m 2. ω 2. r 2 l = m. ω 2. r l 1 m 2. r 2 l = m. r l 1 3

4 lecture - 1 Balancing of Masses Theory of Machine b) When the plane of the disturbing mass lies on one end of the planes of the balancing masses Fig.3. Balancing of a single rotating mass by two rotating masses in different planes, when the plane of single rotating mass lies at one end of the planes of balancing masses. This case shown in Fig.3. As discussed above, the following conditions must be satisfied in order to balance the system, i.e. F C + F C2 = F Cl or m. ω 2. r + m 2. ω 2. r 2 = m 1. ω 2. r 1 m. r + m 2. r 2 = m 1. r 1 Now in order to find the magnitude of balancing force at the bearing B of a shaft, take moments about A. Therefore F C1 l = F C l 2 or m 1. ω 2. r 1 l = m. ω 2. r l 2 m 1. r 1 l = m. r l 2 Similarly, to find the balancing force at the bearing A of a shaft, take moments about B. Therefore F C2 l = F C l 1 or m 2. ω 2. r 2 l = m. ω 2. r l 1 m 2. r 2 l = m. r l 1 3. Balancing of Several Masses Rotating in the Same Plane Consider any number of masses (say four) of magnitude m 1, m 2, m 3 and m 4 at distances of r 1, r 2, r 3 and r 4 from the axis of the rotating shaft. Let θ 1, θ 2,θ 3 and θ 4 4

5 lecture - 1 Balancing of Masses Theory of Machine be the angles of these masses with the horizontal line OX, as shown in Fig. 4 (a). Let these masses rotate about an axis through O and perpendicular to the plane of paper, with a constant angular velocity of ω rad/s. The magnitude and position of the balancing mass may be found out analytically or graphically as discussed below: Fig.4. Balancing of several masses rotating in the same plane. a) Analytical method The magnitude and direction of the balancing mass may be obtained, analytically, as discussed below : Resolve the centrifugal forces horizontally and vertically and find their sums, i.e. ΣH = m 1. r 1 cosθ 1 + m 2. r 2 cosθ ΣV = m 1. r 1 sinθ 1 + m 2. r 2 sinθ Magnitude of the resultant centrifugal force, F C = (Σ ) + (Σ ) If θ is the angle, which the resultant force makes with the horizontal, then tan θ = Σ The balancing force is then equal to the resultant force, but in opposite direction. Now find out the magnitude of the balancing mass, 5

6 lecture - 1 Balancing of Masses Theory of Machine where F C = m. r m = Balancing mass, and r = Its radius of rotation. b) Graphical method The magnitude and position of the balancing mass may also be obtained graphically using Table: 1 and then draw: 1. Find the centrifugal force (or product of the mass and radius of rotation) exerted by each mass on the rotating shaft. 2. Draw the vector diagram with the obtained centrifugal forces to some suitable scale. 3. The closing side of polygon ae represents the resultant force in magnitude and direction, as shown in Fig. 4 (b). 4. The balancing force is, then, equal to the resultant force, but in opposite direction. 5. Find the magnitude of the balancing mass (m) at a given radius of rotation (r), m.r = Resultant of m 1.r 1, m 2.r 2, m 3.r 3 and m 4.r 4 Table: 1 No. of masses Mass (m) Radius (r) Angle( ) Centrifugal force 2 (m.r) 1 m 1 r 1 1 m 1 r 1 2 m 2 r 2 2 m 2.r 2 3 m 3 r 3 3 m 3.r 3 4 m 4 r 4 4 m 4.r 4 4. Balancing of Several Masses Rotating in Different Planes Let us consider four masses m 1, m 2, m 3 and m 4 revolving in planes 1, 2, 3 and 4 respectively as shown in Fig. 5(a). The relative angular positions of these masses 6

7 lecture - 1 Balancing of Masses Theory of Machine Fig. 5. Balancing of several masses rotating in different planes. are shown in Fig. 5(b). The magnitude of the balancing masses m A and m B in planes A and B may be obtained as discussed below: 1. Take one of the planes, say A as the reference plane (R.P.). 2. Tabulate the data as shown in Table: The couples about the reference plane must balance, i.e. the resultant couple must be zero. + m B r B l B cos = 0 sin + m B r B l B sin = 0 4. The forces in the reference plane must balance, i.e. the resultant force must be zero. + m A r A cos = 0 sin + m A r A sin = 0 7

8 lecture - 1 Balancing of Masses Theory of Machine Where n: number of masses. Table: 2 plane Mass (m) Radius (r) Angle( ) Centrifugal force 2 (m.r) Distance from Plane A (l) Couple 2 (m.r.l) 1 m 1 r 1 1 m 1.r 1 l 1 m 1.r 1.l 1 A(R.P.) m A r A A m A.r A m 2 r 2 2 m 2.r 2 l 2 m 2.r 2.l 2 3 m 3 r 3 3 m 3.r 3 l 3 m 3.r 3.l 3 B m B r B B m B.r B l B m B.r B.l B 4 m 4 r 4 4 m 4.r 4 l 4 m 4.r 4.l 4 Graphical Representation 1. Draw moment polygon (assuming that the moment direction is toward the centrifugal force) as shown in Fig.5(c). 2. Draw force polygon as shown in Fig.5(d). Example: 1 Four masses m 1, m 2, m 3 and m 4 are 200 kg, 300 kg, 240 kg and 260 kg respectively. The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and 0.3 m respectively and the angles between successive masses are 45, 75 and 135. Find the position and magnitude of the balance mass required, if its radius of rotation is 0.2 m. Solution: Let m = Balancing mass, and θ = The angle which the balancing mass makes with m Analytical method ΣH = ΣH = 40 cos cos cos cos255 = kg.m 8

9 lecture - 1 Balancing of Masses Theory of Machine No. of masses Mass (kg) Radius (m) Angle(deg.) Centrifugal force 2 (kg.m) m 0.2 m.r ΣV = ΣV = 40 sin sin sin sin255 = 8.43 kg.m F C = ( ) + (843.9) = kg.m F C = m.r, = 0.2 m m = 116 kg Ans. tan θ = Σ =.. = 21.3 Since θ is the angle of the resultant R from the horizontal mass of 200 kg, therefore the angle of the balancing mass from the horizontal mass of 200 kg, θ = = Ans. 2. Graphical method Scale: let 10 kg.m = 1cm in paper. Draw force polygon as shown in Fig.(b). 9

10 lecture - 1 Balancing of Masses Theory of Machine Example: 2 A shaft carries four masses A, B, C and D of magnitude 200 kg, 300 kg, 400 kg and 200 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45, B to C 70 and C to D 120. The balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing masses revolve at a radius of 100 mm, find their magnitudes and angular positions. Solution 10

11 lecture - 1 Balancing of Masses Theory of Machine Home work A shaft has three eccentrics, each 75 mm diameter and 25 mm thick, machined in one piece with the shaft. The central planes of the eccentric are 60 mm apart. The distance of the centres from the axis of rotation are 12 mm, 18 mm and 12 mm and their angular positions are 120 apart. The density of metal is 7000 kg/m 3. Find the amount of out-of-balance force and couple at 600 r.p.m. If the shaft is balanced by adding two masses at a radius 75 mm and at distances of 100 mm from the central plane of the middle eccentric, find the amount of the masses and their angular positions. 11

12 lecture - 1 Balancing of Masses Theory of Machine Solution: 12

13 lecture - 1 Balancing of Masses Theory of Machine 13

14 lecture - 2 Cams Theory of Machine Cams A cam is a rotating machine element which gives reciprocating or oscillating motion to another element known as follower. The cam and follower is one of the simplest as well as one of the most important mechanisms found in modern machinery today. The cams are widely used for operating the inlet and exhaust valves of internal combustion engines. 1. Classification of Cams 1. Radial or disc cam, is shown in Fig. 1 (a) to (f). 2. Cylindrical cam, is shown in Fig Classification of Followers a) According to the surface in contact. The followers, according to the surface in contact, are as follows : a) Knife edge follower, is shown in Fig.1 (a). b) Roller follower, is shown in Fig.1 (b). c) Flat faced or mushroom follower, is shown in Fig.1 (c) and (f ). d) Spherical faced follower, is shown in Fig.1 (d). b) According to the motion of the follower. The followers, according to its motion, are of the following two a) Reciprocating or translating follower, is shown in Fig.1 (a) to (d). b) Oscillating or rotating follower, is shown in Fig.1 (e). c) According to the path of motion of the follower. The followers, according to its path of motion, are of the following two types: 1

15 lecture - 2 Cams Theory of Machine a) Radial follower, is shown in Fig.1 (a) to (e). b) Off-set follower, is shown in Fig.1 ( f ). Fig.1. Classification of followers. Fig.2. Cylindrical cam. 2

16 lecture - 2 Cams Theory of Machine 3. Motion of the Follower The follower, during its travel, may have one of the following motions. 1. Uniform velocity, 2. Simple harmonic motion, and 3. Uniform acceleration and retardation. We shall now discuss the displacement, velocity and acceleration diagrams for the cam when the follower moves with the above mentioned motions. 1. Uniform Velocity Motion The displacement, velocity and acceleration diagrams when a knife-edged follower moves with uniform velocity are shown in Fig. 3(a), (b) and (c) respectively. Since the follower moves with uniform velocity during its rise and return stroke, therefore the slope of the displacement curves must be constant. In other words, AB 1 and C 1 D must be straight lines. The periods during which the follower remains at rest are known as dwell periods as shown by lines B 1 C 1 and DE. The acceleration or retardation of the follower at the beginning and at the end of each stroke is infinite. This is due to the fact that the follower is required to start from rest and has to gain a velocity within no time

17 lecture - 2 Cams Theory of Machine In order to have the acceleration and retardation within the finite limits, it is necessary to modify the conditions which govern the motion of the follower. This may be done by rounding off the sharp corners of the displacement diagram at the beginning and at the end of each stroke, as shown in Fig. 4(a). By doing so, the velocity of the follower increases gradually to its maximum value at the beginning of each stroke and decreases gradually to zero at the end of each stroke as shown in Fig. 4(b). 2. Simple Harmonic Motion The displacement, velocity and acceleration diagrams when the follower moves with simple harmonic motion are shown in Fig. 5(a), (b) and (c) respectively. The displacement diagram is drawn as follows : 1. Draw a semi-circle on the follower stroke as diameter. 2. Divide the semi-circle into any number of even equal parts (say eight). Fig. 5. Displacement, velocity and acceleration diagrams when the follower moves with simple harmonic motion. 4

18 lecture - 2 Cams Theory of Machine 3. Divide the angular displacements of the cam during out stroke and return stroke into the same number of equal parts. 4. The displacement diagram is obtained by projecting the points as shown in Fig. 5(a). Since the follower moves with a simple harmonic motion, therefore velocity diagram consists of a sine curve and the acceleration diagram is a cosine curve. Let S = Stroke of the follower, θ O and θ R = Angular displacement of the cam during out stroke and return stroke of the follower respectively, in radians, and ω = Angular velocity of the cam in rad/s. (t O = O / ) 3. Uniform Acceleration and Retardation 5

19 lecture - 2 Cams Theory of Machine The displacement, velocity and acceleration diagrams when the follower moves with uniform acceleration and retardation are shown in Fig. 7(a), ( b) and ( c) respectively. We see that the displacement diagram consists of a parabolic curve and may be drawn as discussed below : 1. Divide the angular displacement of the cam during outstroke (θ O ) into any even number of equal parts (say eight) and dr aw vertical lines through these points. 2. Divide the stroke of the follower (S) into the same number of equal even parts. 3. Join Aa to intersect the vertical line through point 1 at B. Similarly, obtain the other points C, D etc., Fig. 7(a). Now join these points to obtain the parabolic curve for the out stroke of the follower. 4. In the similar way as discussed above, the displacement diagram for the follower during return stroke may be drawn. Since the acceleration and retardation are uniform, therefore the velocity varies directly with the time. We know that time required for the follower during outstroke, t O = θ O / ω and time required for the follower during return stroke, t R = θ R / ω Mean velocity of the follower during outstroke = S / t O and mean velocity of the follower during return stroke = S / t R Maximum velocity of the follower during outstroke, v O = =. θ Similarly, maximum velocity of the follower during return stroke, v R =. θ 6

20 lecture - 2 Cams Theory of Machine Fig. 7. Displacement, velocity and acceleration diagrams when the follower moves with uniform acceleration and retardation. Maximum acceleration of the follower during outstroke, a O = =.. θ =. ( ) (t O = O / ) Similarly, maximum acceleration of the follower during return stroke, a R =. ( ) 7

21 lecture - 2 Cams Theory of Machine Construction of Cam Profile In order to draw the cam profile for a radial cam, first of all the displacement diagram for the given motion of the follower is drawn. Then the principle of kinematic inversion is used, i.e. the cam is imagined to be stationary and the follower is allowed to rotate in the opposite direction to the cam rotation. Example: 1 A cam is to give the following motion to a knife-edged follower: 1. Outstroke during 60 of cam rotation; 2. Dwell for the next 30 of cam rotation ; 3. Return stroke during next 60 of cam rotation, and 4. Dwell for the remaining 210 of cam rotation. The stroke of the follower is 40 mm and the minimum radius of the cam is 50mm. The follower moves with uniform velocity during both the outstroke and return strokes. Draw the profile of the cam when a) the axis of the follower passes through the axis of the cam shaft, and b) the axis of the follower is offset by 20mm from the axis of the cam shaft. Solution: First of all, the displacement diagram, as shown in Fig. 8, is drawn as discussed in the following steps : 1. Draw a horizontal line AX = 360 to some suitable scale. AS = O = 60 ST = D = 30 TP = R = 60 PX = D = Draw vertical line AY equal to the stroke of the follower ( i.e. 40 mm) and complete the rectangle as shown in Fig. 8. 8

22 lecture - 2 Cams Theory of Machine 3. Divide the angular displacement during outstroke and return stroke into any equal number of even parts (say six) and draw vertical lines through each point. 4. Since the follower moves with uniform velocity during outstroke and return stroke, therefore the displacement diagram consists of straight lines. Join AG and HP. 5. The complete displacement diagram is shown by AGHPX. (a) The profile of the cam when the axis of the follower passes through the axis of the cam shaft, as shown in Fig. 9, is drawn as discussed in the following steps: 1. Draw a base circle with radius equal to the minimum radius of the cam (i.e. 50 mm). 2. From OA, mark angle AOS = O = 60 SOT = D = 30 TOP = R = Divide the angular displacements during outstroke and return stroke ( i.e. angle AOS and angle TOP) into the same number of equal even parts as in displacement diagram. 4. Now set off 1B, 2C, 3D... etc. and 0 H,1 J... etc. from the displacement diagram. 9

23 lecture - 2 Cams Theory of Machine 5. Join the points A, B, C,... M, N, P with a smooth curve. The curve AGHPA is the complete profile of the cam. (b) The profile of the cam when the axis of the follower is offset by 20 mm from the axis of the cam shaft, as shown in Fig. 10, is drawn as discussed in the following steps : 1. Draw a base circle with radius equal to the minimum radius of the cam (i.e. 50 mm) with O as centre. 2. Draw the axis of the follower at a distance of 20 mm from the axis of the cam, which intersects the base circle at A. 3. Join AO and draw an offset circle of radius 20 mm with centre O. 4. From OA, mark angle AOS = O = 60 SOT = D = 30 TOP = R = 60 10

24 lecture - 2 Cams Theory of Machine 5. Divide the angular displacement during outstroke and return stroke ( i.e. angle AOS and angle TOP) into the same number of equal even parts as in displacement diagram. 6. Now from the points 1, 2, 3... etc. and 0,1, 2,3... etc. on the base circle, draw tangents to the offset circle. 7. Now set off 1B, 2C, 3D... etc. and 0 H,1 J... etc. from the displacement diagram. 8. Join the points A, B, C...M, N, P with a smooth curve. The curve AGHPA is the complete profile of the cam. Example: 2 A cam, with a minimum radius of 25 mm, rotating clockwise at a uniform speed is to be designed to give a roller follower, at the end of a valve rod, motion described below : 1. To raise the valve through 50 mm during 120 rotation of the cam ; 11

25 lecture - 2 Cams Theory of Machine 2. To keep the valve fully raised through next 30 ; 3. To lower the valve during next 60 ; and 4. To keep the valve closed during rest of the revolution i.e. 150 ; The diameter of the roller is 20 mm and the diameter of the cam shaft is 25 mm. Draw the profile of the cam when a) the line of stroke of the valve rod passes through the axis of the cam shaft, b) the line of the stroke is offset 15 mm from the axis of the cam shaft. The displacement of the valve, while being raised and lowered, is to take place with simple harmonic motion. Determine the maximum acceleration of the valve rod when the cam shaft rotates at 100 r.p.m. Draw the displacement, the velocity and the acceleration diagrams for one complete revolution of the cam. Solution: First of all, the displacement diagram, as shown in Fig. 11(a), is drawn as discussed in the following steps : 1. Draw horizontal line AX = 360 to some suitable scale. On this line, mark AS = O = 120 ST = D = 30 TP = R = 60 PX = D = Draw vertical line AY = 50 mm to represent the cam lift or stroke of the follower and complete the rectangle. 3. Divide the angular displacement during out stroke and return stroke into any equal number of even parts (say six) and draw vertical lines through each point. 4. Since the follower moves with simple harmonic motion, therefore draw a semicircle with AY as diameter and divide into six equal parts. 5. From points a, b, c... etc. draw horizontal lines intersecting the vertical lines drawn through 1, 2, 3... etc. and 0,1, 2...etc. at B, C, D... M, N, P. 12

26 lecture - 2 Cams Theory of Machine 6. Join the points A, B, C... etc. with a smooth curve. Fig. 11 (c) Acceleration diagram (a) The profile of the cam when the line of stroke of the valve rod passes through the axis of the cam shaft, as shown in Fig. 13, is drawn as discussed in the following steps : 1. Draw a base circle with centre O and radius equal to the minimum radius of the cam ( i.e. 25 mm ). 2. Draw a prime circle with centre O and radius, OA = Min. radius of cam + Dia. of roller = = 35 mm 13

27 lecture - 2 Cams Theory of Machine 3. From OA, mark angle AOS = O = 120 SOT = D = 30 TOP = R = Divide the angular displacements of the cam during raising and lowering of the valve (i.e. angle AOS and TOP ) into the same number of equal even parts as in displacement diagram. 5. Join the points 1, 2, 3, etc. with the centre O and produce the lines beyond prime circle. 6. Set off 1B, 2C, 3D etc. equal to the displacements from displacement diagram. 7. Join the points A, B, C... N, P, A. The curve drawn through these points is known as pitch curve. 14

28 lecture - 2 Cams Theory of Machine 8. From the points A, B, C... N, P, draw circles of radius equal to the radius of the roller. 9. Join the bottoms of the circles with a smooth curve. (b) Profile of the cam when the line of stroke is offset 15 mm from the axis of the cam shaft, as shown in Fig. 14, may be drawn as discussed in the following steps: 1. Draw a base circle with centre O and radius equal to 25 mm. 2. Draw a prime circle with centre O and radius OA = 35 mm. 3. Draw an off-set circle with centre O and radius equal to 15 mm. 4. Join OA. From OA draw the angular displacements of cam i.e. draw angle AOS = 120,angle SOT = 30 and angle TOP = Divide the angular displacements of the cam during raising and lowering of the valve into the same number of equal even parts (i.e. six parts ) as in displacement diagram. 6. From points 1, 2, 3... etc. and 0,1, 3,...etc. on the prime circle, draw tangents to the offset circle. 7. Set off 1B, 2C, 3D... etc. equal to displacements as measured from displacement diagram. 8. By joining the points A, B, C... M, N, P, with a smooth curve, we get a pitch curve. 9. Now A, B, C...etc. as centre, draw circles with radius equal to the radius of roller. 10.Join the bottoms of the circles with a smooth curve. 15

29 lecture - 2 Cams Theory of Machine 16

30 lecture - 2 Cams Theory of Machine Home Work A cam, with a minimum radius of 50 mm, rotating clockwise at a uniform speed, is required to give a knife edge follower the motion as described below: 1. To move outwards through 40 mm during 100 rotation of the cam; 2. To dwell for next 80 ; 3. To return to its starting position during next 90, and 4. To dwell for the rest period of a revolution i.e. 90. Draw the profile of the cam i. when the line of stroke of the follower passes through the centre of the cam shaft, ii. when the line of stroke of the follower is off-set by 15 mm. The displacement of the follower is to take place with uniform acceleration and uniform retardation. Determine the maximum velocity and acceleration of the follower when the cam shaft rotates at 900 r.p.m. Draw the displacement, velocity and acceleration diagrams for one complete revolution of the cam. 17

31 lecture - 3 Governors Theory of Machine Governors 1. Introduction The function of a governor is to regulate the mean speed of an engine, when there are variations in the load e.g. when the load on an engine increases, its speed decreases, therefore it becomes necessary to increase the supply of working fluid. On the other hand, when the load on the engine decreases, its speed increases and thus less working fluid is required. The governor automatically controls the supply of working fluid to the engine with the varying load conditions and keeps the mean speed within certain limits. 2. Types of Governors The governors may, broadly, be classified as 1. Centrifugal governors, and 2. Inertia governors. The centrifugal governors, may further be classified as follows : 1

32 lecture - 3 Governors Theory of Machine 3. Terms Used in Governors The following terms used in governors; 1. Height of a governor. It is the vertical distance from the center of the ball to a point where the axes of the arms (or arms produced) intersect on the spindle axis. It is usually denoted by h. 2. Equilibrium speed. It is the speed at which the governor balls, arms etc., are in complete equilibrium and the sleeve does not tend to move upwards or downwards. 3. Mean equilibrium speed. It is the speed at the mean position of the balls or the sleeve. 4. Maximum and minimum equilibrium speeds. The speeds at the maximum and minimum radius of rotation of the balls, without tending to move either way are known as maximum and minimum equilibrium speeds respectively. 5. Sleeve lift. It is the vertical distance which the sleeve travels due to change in equilibrium speed. Fig.1. Centrifugal governor. 2

33 lecture - 3 Governors Theory of Machine 4. Watt Governor The simplest form of a centrifugal governor is a Watt governor, as shown in Fig.2. It is basically a conical pendulum with links attached to a sleeve of negligible mass. The arms of the governor may be connected to the spindle in the following three ways: 1. The pivot P, may be on the spindle axis as shown in Fig.2 (a). 2. The pivot P, may be offset from the spindle axis and the arms when produced intersect at O, as shown in Fig.2 (b). 3. The pivot P, may be offset, but the arms cross the axis at O, as shown in Fig.2 (c). Fig.2. Watt governor. Let m = Mass of the ball in kg, w = Weight of the ball in newtons = m.g, T = Tension in the arm in newtons, ω = Angular velocity of the arm and ball about the spindle axis in rad/s, r = Radius of the path of rotation of the ball i.e. horizontal distance from the center of the ball to the spindle axis in meters, F C = Centrifugal force acting on the ball in newtons = m.ω 2.r, and h = Height of the governor in meters. 3

34 lecture - 3 Governors Theory of Machine It is assumed that the weight of the arms, links and the sleeve are negligible as compared to the weight of the balls. Now, the ball is in equilibrium under the action of 1. the centrifugal force (F C ) acting on the ball, 2. the tension (T) in the arm, and 3. the weight (w) of the ball. Taking moments about point O, we have F C h = w r = m.g.r or m.ω 2.r.h = m.g.r or h = g /ω 2. (1) Note: Watt governor may only work satisfactorily at relatively low speeds i.e. from 60 to 80 r.p.m. 5. Porter Governor The Porter governor is a modification of a Watt governor, with central load attached to the sleeve as shown in Fig.3 (a). The load moves up and down the central spindle. This additional downward force increases the speed of revolution required to enable the balls to rise to any predetermined level. Consider the forces acting on one-half of the governor as shown in Fig.3 (b). Fig.3. Porter governor. Let m = Mass of each ball in kg, 4

35 lecture - 3 Governors Theory of Machine w = Weight of each ball in newtons = m.g, M = Mass of the central load in kg, W = Weight of the central load in newtons = M.g, r = Radius of rotation in metres h = Height of governor in metres, N = Speed of the balls in r.p.m., ω = Angular speed of the balls = 2 πn/60 rad/s, F C = Centrifugal force acting on the ball in newtons = m.ω 2.r, T 1 = Force in the arm in newtons, T 2 = Force in the link in newtons, α = Angle of inclination of the arm (or upper link) to the vertical, and β = Angle of inclination of the link (or lower link) to the vertical. Though there are several ways of determining the relation between the height of the governor (h) and the angular speed of the balls (ω), the following two methods are used: 1. Method of resolution of forces ; and 2. Instantaneous centre method. 1. Method of resolution of forces Considering the equilibrium of the forces acting at D, we have T 2 cos = =. or T 2 =. Again, considering the equilibrium of the forces acting on B. F y = 0 (1) F x = 0 5

36 lecture - 3 Governors Theory of Machine Dividing equation (2) by equation (1),.(2) Notes : 1. When the length of arms are equal to the length of links and the points P and D lie on the same vertical line, then tan α = tan β or q = tan α / tan β = 1 h =. 2. When the loaded sleeve moves up and down the spindle, the frictional force acts on it in a direction opposite to that of the motion of sleeve. If F = Frictional force acting on the sleeve 6

37 lecture - 3 Governors Theory of Machine h =.. ± ( ). The + sign is used when the sleeve moves upwards or the governor speed increases and sign is used when the sleeve moves downwards or the governor speed decreases. 2. Instantaneous centre method In this method, equilibrium of the forces acting on the link BD are considered. The instantaneous centre I lies at the point of intersection of PB produced and a line through D perpendicular to the spindle axis, as shown in Fig.4. Taking moments about the point I, F C BM = w IM + ID = m. g IM +. ID Fig.4. Instantaneous centre method. Example: 1 In an engine governor of the Porter type, the upper and lower arms are 200mm and 250 mm respectively and pivoted on the axis of rotation. The mass 7

38 lecture - 3 Governors Theory of Machine of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 25 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30 and 40, find, taking friction into account, range of speed of the governor. Solution: Minimum radius of rotation, r 1 = BG = BP sin 30 = = 0.1 m Height of the governor, h 1 = PG = BP cos 30 = = m DG = (BD) 2 (BG) 2 = (0.25) 2 (0.1) 2 = 0.23m tan β 1 = BG/DG = 0.1/0.23 = tan α 1 = tan 30 = q 1 = =.. =.. = ( ). =.. (. ).. 1 = 19.2 rad/s Maximum radius of rotation, r 2 = BG = BP sin 40 = = m Height of the governor, h 2 = PG = BP cos 40 = = m 8

39 lecture - 3 Governors Theory of Machine DG = (BD) 2 (BG) 2 = (0.25) 2 (0.1268) 2 = m tan β 2 = BG/DG = / = 0.59 tan α 2 = tan 40 = q 2 = =. =... = ( ). =.. (. ).. 2 = rad/s Range of speed = 2 1 = = 4.05 rad/s Ans. Proell Governor The Proell governor has the balls fixed at B and C to the extension of the links DF and EG, as shown in Fig. 1(a). The arms FP and GQ are pivoted at P and Q respectively. Consider the equilibrium of the forces on one-half of the governor as shown in Fig. 1(b). The instantaneous centre ( I) lies on the intersection of the line PF produced and the line from D drawn perpendicular to the spindle axis. The perpendicular BM is drawn on ID. Fig. 1 Proell governor. Taking moments about I, 9

40 lecture - 3 Governors Theory of Machine (1)... (2) Note : When α = β, then q = 1. Therefore equation (2) may be written as h = ( ). Example: 2 The following particulars refer to a Proell governor with open arms: Length of all arms = 200 mm ; distance of pivot of arms from the axis of rotation = 40mm ; length of extension of lower arms to which each ball is attached = 100mm ; mass of each ball = 6 kg and mass of the central load = 150 kg. If the radius of rotation of the balls is 180 mm when the arms are inclined at an angle of 40 to the axis of rotation, find the equilibrium speed for the above configuration. Solution: 10

41 lecture - 3 Governors Theory of Machine Home Work A governor of the Proell type has each arm 250 mm long. The pivots of the upper and lower arms are 25 mm from the axis. The central load acting on the sleeve has a mass of 25 kg and the each rotating ball has a mass of 3.2 kg. When the governor sleeve is in mid-position, the extension link of the lower arm is vertical and the 11

42 lecture - 3 Governors Theory of Machine radius of the path of rotation of the masses is 175 mm. The vertical height of the governor is 200 mm. If the governor speed is 160 r.p.m. when in mid-position, find: 1. length of the extension link; and 2. tension in the upper arm. Answers : 1. BF = 108 mm 2. T= N 12

43 lecture - 4 Gyroscopic Couple and Precessional Motion Theory of Machine Gyroscopic Couple and Precessional Motion When a body moves along a curved path with a uniform linear velocity, a force in the direction of centripetal acceleration (known as centr ipetal force) has to be applied externally over the body, so that it moves along the required curved path. This external force applied is known as active force. When a body, itself, is moving with uniform linear velocity along a circular path, it is subjected to the centrifugal force radially outwards. This centrifugal force is called reactive force. The action of the reactive or centrifugal force is to tilt or move the body along radially outward direction. Centrifugal force is equal in magnitude to centripetal force but opposite in direction. The gyroscopes are installed in ships in order to minimize the rolling and pitching effects of waves. They are also used in aeroplanes, monorail cars, gyrocompasses etc. Gyroscopic Couple Consider a disc spinning with an angular velocity ( ω rad/s ) about the axis of spin OX, in anticlockwise direction when seen from the front. Since the plane in which the disc is rotating is parallel to the plane YOZ, therefore it is called plane of spinning. The plane XOZ is a horizontal plane and the axis of spin rotates in a plane parallel to the horizontal 1

44 lecture - 4 Gyroscopic Couple and Precessional Motion Theory of Machine plane about an axis OY. In other words, the axis of spin is said to be rotating or processing about an axis OY. In other words, the axis of spin is said to be rotating or processing about an axis OY (which is perpendicular to both the axes OX and OZ) at an angular velocity ( ω P rap/s). This horizontal plane XOZ is called plane of precession and OY is the axis of precession. Let I = Mass moment of inertia of the disc about OX, and ω = Angular velocity of the disc. Angular momentum of the disc = I. ω 2

45 lecture - 4 Gyroscopic Couple and Precessional Motion Theory of Machine Where ω P = Angular velocity of precession of the axis of spin or the speed of rotation of the axis of spin about the axis of precession OY. The units of C is N-m when I is in kg-m 2. Example 1: A uniform disc of diameter 300 mm and of mass 5 kg is mounted on one end of an arm of length 600 mm. The other end of the arm is free to rotate in a universal bearing. If the disc rotates about the arm with a speed of 300 r.p.m. clockwise, looking from the front, with what speed will it precess about the vertical axis? Solution: We know that the mass moment of inertia of the disc, about an axis through its center of gravity and perpendicular to the plane of disc, Example 2: A uniform disc of 150 mm diameter has a mass of 5 kg. It is mounted centrally in bearings which maintain its axle in a horizontal plane. The disc spins about it axle with a constant speed of 1000 r.p.m. while the axle precesses uniformly about the vertical at 60 r.p.m. The directions of rotation are as shown in Figure. If the distance between the bearings is 100 mm, find the resultant reaction at each bearing due to the mass and gyroscopic effects. Solution: The direction of the reactive gyroscopic couple is shown in Figure. Let F be the force at each bearing due to the gyroscopic couple. 3

46 lecture - 4 Gyroscopic Couple and Precessional Motion Theory of Machine The force F will act in opposite directions at the bearings as shown in Figure. Now let R A and R B be the reaction at the bearing A and B respectively due to the weight of the disc. Since the disc is mounted centrally in bearings, therefore, Effect of the Gyroscopic Couple on an Aeroplane Let engine or propeller rotates in the clockwise direction when seen from the rear or tail end and the aeroplane takes a turn to the left. 4

47 lecture - 4 Gyroscopic Couple and Precessional Motion Theory of Machine Example 3: An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hr. The rotary engine and the propeller of the plane has a mass of 400 kg and a radius of gyration of 0.3 m. The engine rotates at 2400 r.p.m. clockwise when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it. Solution: 5

Cams. 774 l Theory of Machines

Cams. 774 l Theory of Machines 774 l Theory of Machines 0 Fea eatur tures es 1. Introduction.. Classification of Followers. 3. Classification of Cams. 4. Terms used in Radial cams. 5. Motion of the Follower. 6. Displacement, Velocity

More information

UNIT 6 GOVERNORS. 6.5 Controlling force and and stability of spring controlled Governors. Compiled By. Dr. B. Suresha, Professor

UNIT 6 GOVERNORS. 6.5 Controlling force and and stability of spring controlled Governors. Compiled By. Dr. B. Suresha, Professor UNIT 6 GOVERNORS STRUCTURE 6.1 Introduction 6.1.1 Objectives 6. Types of Governors 6..1 Porter Governor 6.. Hartnell Governor 6.3 Governor effort and Power 6.4 Characteristics of Governors 6.5 Controlling

More information

Flywheels-Function need and Operation

Flywheels-Function need and Operation STUDY OF FLYWHEEL Flywheel definition A flywheel is an inertial energy-storage device. It absorbs mechanical energy and serves as a reservoir, storing energy during the period when the supply of energy

More information

Governors. Chapter : Governors l 653

Governors. Chapter : Governors l 653 18 Chapter : Governors l 653 Features 1. Introduction.. Tpes of Governors. 3. Centrifugal Governors. 4. Terms Used in Governors. 5. Watt Governor. 6. Porter Governor. 7. Proell Governor. 8. Hartnell Governor.

More information

Fig. 6.1 Plate or disk cam.

Fig. 6.1 Plate or disk cam. CAMS INTRODUCTION A cam is a mechanical device used to transmit motion to a follower by direct contact. The driver is called the cam and the driven member is called the follower. In a cam follower pair,

More information

Gyroscopic Couple and Precessional Motion

Gyroscopic Couple and Precessional Motion 480 l Theory of Machines 14 Fea eatur tures es 1. Introduction.. Precessional Angular Motion. 3. Gyroscopic Couple. 4. Effect of Gyroscopic Couple on an Aeroplane. 5. Terms Used in a Naval Ship. 6. Effect

More information

Dynamics of Machinery

Dynamics of Machinery Dynamics of Machinery Two Mark Questions & Answers Varun B Page 1 Force Analysis 1. Define inertia force. Inertia force is an imaginary force, which when acts upon a rigid body, brings it to an equilibrium

More information

UNIT 5 GOVERNORS 5.1 INTRODUCTION. Structure. 5.1 Introduction. 5.2 Classification of Governors 5.3 Gravity Controlled Centrifugal Governors

UNIT 5 GOVERNORS 5.1 INTRODUCTION. Structure. 5.1 Introduction. 5.2 Classification of Governors 5.3 Gravity Controlled Centrifugal Governors UNIT 5 GVERNRS Governors Structure 5. Introduction bjectives 5. lassification of Governors 5.3 Gravity ontrolled entrifugal Governors 5.3. Watt Governor 5.3. Porter Governor 5.4 Spring ontrolled entrifugal

More information

LABORATORY MANUAL DYNAMICS OF MACHINE ME-314-E

LABORATORY MANUAL DYNAMICS OF MACHINE ME-314-E LABORATORY MANUAL DYNAMICS OF MACHINE ME-314-E 1 LIST OF EXPERIMENTS S. No. NAME OF EXPERIMENTS PAGE No. 1. To perform experiment on watt and Porter Governors to prepare performance characteristic Curves,

More information

This equation of motion may be solved either by differential equation method or by graphical method as discussed below:

This equation of motion may be solved either by differential equation method or by graphical method as discussed below: 2.15. Frequency of Under Damped Forced Vibrations Consider a system consisting of spring, mass and damper as shown in Fig. 22. Let the system is acted upon by an external periodic (i.e. simple harmonic)

More information

TOPIC : 8 : Balancing

TOPIC : 8 : Balancing TOPIC : 8 : Balancing --------------------------------------------------------------- Q.1. What is balancing? What are its objectives? What are types of balancing? BALANCING: Balancing is the technique

More information

UNIT-I (FORCE ANALYSIS)

UNIT-I (FORCE ANALYSIS) DHANALAKSHMI SRINIVASAN INSTITUTE OF RESEACH AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK ME2302 DYNAMICS OF MACHINERY III YEAR/ V SEMESTER UNIT-I (FORCE ANALYSIS) PART-A (2 marks)

More information

Balancing of Rotating Masses

Balancing of Rotating Masses Balancing of Rotating Masses 1 Balancing of Rotating Masses m Consider first a single mass m moving in a circular arc of radius r with an angular velocity rad/s. The mass has a centripetal (centre 2 seeking)

More information

OUTCOME 2 KINEMATICS AND DYNAMICS

OUTCOME 2 KINEMATICS AND DYNAMICS Unit 60: Dynamics of Machines Unit code: H/601/1411 QCF Level:4 Credit value:15 OUTCOME 2 KINEMATICS AND DYNAMICS TUTORIAL 3 GYROSCOPES 2 Be able to determine the kinetic and dynamic parameters of mechanical

More information

Kinematics of. Motion. 8 l Theory of Machines

Kinematics of. Motion. 8 l Theory of Machines 8 l Theory of Machines Features 1. 1ntroduction.. Plane Motion. 3. Rectilinear Motion. 4. Curvilinear Motion. 5. Linear Displacement. 6. Linear Velocity. 7. Linear Acceleration. 8. Equations of Linear

More information

ME 6505 DYNAMICS OF MACHINES Fifth Semester Mechanical Engineering (Regulations 2013)

ME 6505 DYNAMICS OF MACHINES Fifth Semester Mechanical Engineering (Regulations 2013) ME 6505 DYNAMICS OF MACHINES Fifth Semester Mechanical Engineering (Regulations 2013) Unit II PART A 1. Define static balancing of shaft. (N/D 15) The net dynamic force acting on the shaft is equal to

More information

AP Physics QUIZ Chapters 10

AP Physics QUIZ Chapters 10 Name: 1. Torque is the rotational analogue of (A) Kinetic Energy (B) Linear Momentum (C) Acceleration (D) Force (E) Mass A 5-kilogram sphere is connected to a 10-kilogram sphere by a rigid rod of negligible

More information

LAB MANNUAL DYNAMICS OF MACHINE

LAB MANNUAL DYNAMICS OF MACHINE LAB MANNUAL OF DYNAMICS OF MACHINE (ME- 314-E) DEPTT. OF MECHANICAL ENGINEERING OM INSTITUTE OF TECHNOLOGY & MANAGEMENT 12km Stone, NH-65, Chandigarh Road Juglan (Hisar) Web Site-www.oitmhisar.com, Email:-

More information

ME2302 DYNAMICS OF MACHINERY

ME2302 DYNAMICS OF MACHINERY ME2302 DYNAMICS OF MACHINERY TWO MARKS QUESTION AND ANSWERS 1. What are the conditions for a body to be in static and dynamic equilibrium? Necessary and sufficient conditions for static and dynamic equilibrium

More information

[You will experience the effect of a centrifugal force if you swing a mass on the end of a piece of string around in a circle.]

[You will experience the effect of a centrifugal force if you swing a mass on the end of a piece of string around in a circle.] Balancing Rotating Masses The balancing of rotating bodies is important to avoid the damaging effects of vibration. Vibrations are noisy and uncomfortable. For example, when a car wheel is out of balance,

More information

ME6511 DYNAMICS LABORATORY LIST OF EXPERIMENTS 1. Free Transverse Vibration I Determination of Natural Frequency 2. Cam Analysis Cam Profile and Jump-speed Characteristics 3. Free Transverse Vibration

More information

LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR.

LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR. LANMARK UNIVERSITY OMU-ARAN, KWARA STATE DEPARTMENT OF MECHANICAL ENGINEERING COURSE: MECHANICS OF MACHINE (MCE 322). LECTURER: ENGR. IBIKUNLE ROTIMI ADEDAYO SIMPLE HARMONIC MOTION. Introduction Consider

More information

CHAPTER 8: ROTATIONAL OF RIGID BODY PHYSICS. 1. Define Torque

CHAPTER 8: ROTATIONAL OF RIGID BODY PHYSICS. 1. Define Torque 7 1. Define Torque 2. State the conditions for equilibrium of rigid body (Hint: 2 conditions) 3. Define angular displacement 4. Define average angular velocity 5. Define instantaneous angular velocity

More information

Rotational Kinematics and Dynamics. UCVTS AIT Physics

Rotational Kinematics and Dynamics. UCVTS AIT Physics Rotational Kinematics and Dynamics UCVTS AIT Physics Angular Position Axis of rotation is the center of the disc Choose a fixed reference line Point P is at a fixed distance r from the origin Angular Position,

More information

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm.

6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm. 1. During a certain period of time, the angular position of a swinging door is described by θ = 5.00 + 10.0t + 2.00t 2, where θ is in radians and t is in seconds. Determine the angular position, angular

More information

Varuvan Vadivelan. Institute of Technology LAB MANUAL. : 2013 : B.E. MECHANICAL ENGINEERING : III Year / V Semester. Regulation Branch Year & Semester

Varuvan Vadivelan. Institute of Technology LAB MANUAL. : 2013 : B.E. MECHANICAL ENGINEERING : III Year / V Semester. Regulation Branch Year & Semester Varuvan Vadivelan Institute of Technology Dharmapuri 636 703 LAB MANUAL Regulation Branch Year & Semester : 2013 : B.E. MECHANICAL ENGINEERING : III Year / V Semester ME 6511 - DYNAMICS LABORATORY GENERAL

More information

TutorBreeze.com 7. ROTATIONAL MOTION. 3. If the angular velocity of a spinning body points out of the page, then describe how is the body spinning?

TutorBreeze.com 7. ROTATIONAL MOTION. 3. If the angular velocity of a spinning body points out of the page, then describe how is the body spinning? 1. rpm is about rad/s. 7. ROTATIONAL MOTION 2. A wheel rotates with constant angular acceleration of π rad/s 2. During the time interval from t 1 to t 2, its angular displacement is π rad. At time t 2

More information

Physics 12. Unit 5 Circular Motion and Gravitation Part 1

Physics 12. Unit 5 Circular Motion and Gravitation Part 1 Physics 12 Unit 5 Circular Motion and Gravitation Part 1 1. Nonlinear motions According to the Newton s first law, an object remains its tendency of motion as long as there is no external force acting

More information

31 ROTATIONAL KINEMATICS

31 ROTATIONAL KINEMATICS 31 ROTATIONAL KINEMATICS 1. Compare and contrast circular motion and rotation? Address the following Which involves an object and which involves a system? Does an object/system in circular motion have

More information

ENGINEERING COUNCIL DYNAMICS OF MECHANICAL SYSTEMS D225 TUTORIAL 8 BALANCING OF ROTATING BODIES

ENGINEERING COUNCIL DYNAMICS OF MECHANICAL SYSTEMS D225 TUTORIAL 8 BALANCING OF ROTATING BODIES ENGINEERING COUNCIL DYNAMICS OF MECHANICAL SYSTEMS D225 TUTORIAL 8 BALANCING OF ROTATING BODIES On completion of this tutorial you should be able to do the following. Explain the importance of balancing.

More information

Advanced Higher Physics. Rotational motion

Advanced Higher Physics. Rotational motion Wallace Hall Academy Physics Department Advanced Higher Physics Rotational motion Problems AH Physics: Rotational Motion 1 2013 Data Common Physical Quantities QUANTITY SYMBOL VALUE Gravitational acceleration

More information

TOPIC D: ROTATION EXAMPLES SPRING 2018

TOPIC D: ROTATION EXAMPLES SPRING 2018 TOPIC D: ROTATION EXAMPLES SPRING 018 Q1. A car accelerates uniformly from rest to 80 km hr 1 in 6 s. The wheels have a radius of 30 cm. What is the angular acceleration of the wheels? Q. The University

More information

The University of Melbourne Engineering Mechanics

The University of Melbourne Engineering Mechanics The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant

More information

Name: Date: Period: AP Physics C Rotational Motion HO19

Name: Date: Period: AP Physics C Rotational Motion HO19 1.) A wheel turns with constant acceleration 0.450 rad/s 2. (9-9) Rotational Motion H19 How much time does it take to reach an angular velocity of 8.00 rad/s, starting from rest? Through how many revolutions

More information

= o + t = ot + ½ t 2 = o + 2

= o + t = ot + ½ t 2 = o + 2 Chapters 8-9 Rotational Kinematics and Dynamics Rotational motion Rotational motion refers to the motion of an object or system that spins about an axis. The axis of rotation is the line about which the

More information

DEPARTMENT OF MECHANICAL ENGINEERING Dynamics of Machinery. Submitted

DEPARTMENT OF MECHANICAL ENGINEERING Dynamics of Machinery. Submitted DEPARTMENT OF MECHANICAL ENGINEERING Dynamics of Machinery Submitted 1 UNIT I - Force Analysis INDEX (1) Introduction (2) Newton s Law (3) Types of force Analysis (4) Principle of Super Position (5) Free

More information

Dynamics Plane kinematics of rigid bodies Section 4: TJW Rotation: Example 1

Dynamics Plane kinematics of rigid bodies Section 4: TJW Rotation: Example 1 Section 4: TJW Rotation: Example 1 The pinion A of the hoist motor drives gear B, which is attached to the hoisting drum. The load L is lifted from its rest position and acquires an upward velocity of

More information

Chapter 8 Lecture. Pearson Physics. Rotational Motion and Equilibrium. Prepared by Chris Chiaverina Pearson Education, Inc.

Chapter 8 Lecture. Pearson Physics. Rotational Motion and Equilibrium. Prepared by Chris Chiaverina Pearson Education, Inc. Chapter 8 Lecture Pearson Physics Rotational Motion and Equilibrium Prepared by Chris Chiaverina Chapter Contents Describing Angular Motion Rolling Motion and the Moment of Inertia Torque Static Equilibrium

More information

WORK SHEET FOR MEP311

WORK SHEET FOR MEP311 EXPERIMENT II-1A STUDY OF PRESSURE DISTRIBUTIONS IN LUBRICATING OIL FILMS USING MICHELL TILTING PAD APPARATUS OBJECTIVE To study generation of pressure profile along and across the thick fluid film (converging,

More information

PLANAR RIGID BODY MOTION: TRANSLATION &

PLANAR RIGID BODY MOTION: TRANSLATION & PLANAR RIGID BODY MOTION: TRANSLATION & Today s Objectives : ROTATION Students will be able to: 1. Analyze the kinematics of a rigid body undergoing planar translation or rotation about a fixed axis. In-Class

More information

Force, Energy & Periodic Motion. Preparation for unit test

Force, Energy & Periodic Motion. Preparation for unit test Force, Energy & Periodic Motion Preparation for unit test Summary of assessment standards (Unit assessment standard only) In the unit test you can expect to be asked at least one question on each sub-skill.

More information

Department of Mechanical Engineering ME6505- DYNAMICS OF MACHINES. Two Marks Question and answer UNIT I FORCE ANALYSIS AND FLYWHEELS

Department of Mechanical Engineering ME6505- DYNAMICS OF MACHINES. Two Marks Question and answer UNIT I FORCE ANALYSIS AND FLYWHEELS Department of Mechanical Engineering ME6505- DYNAMICS OF MACHINES Two Marks Question and answer UNIT I FORCE ANALYSIS AND FLYWHEELS 1. Distinguish between space diagram and free body diagram Space Diagram

More information

Circular Motion, Pt 2: Angular Dynamics. Mr. Velazquez AP/Honors Physics

Circular Motion, Pt 2: Angular Dynamics. Mr. Velazquez AP/Honors Physics Circular Motion, Pt 2: Angular Dynamics Mr. Velazquez AP/Honors Physics Formulas: Angular Kinematics (θ must be in radians): s = rθ Arc Length 360 = 2π rads = 1 rev ω = θ t = v t r Angular Velocity α av

More information

ROTATORY MOTION. ii) iii) iv) W = v) Power = vi) Torque ( vii) Angular momentum (L) = Iω similar to P = mv 1 Iω. similar to F = ma

ROTATORY MOTION. ii) iii) iv) W = v) Power = vi) Torque ( vii) Angular momentum (L) = Iω similar to P = mv 1 Iω. similar to F = ma OTATOY MOTION Synopsis : CICULA MOTION :. In translatory motion, every particle travels the same distance along parallel paths, which may be straight or curved. Every particle of the body has the same

More information

Webreview Torque and Rotation Practice Test

Webreview Torque and Rotation Practice Test Please do not write on test. ID A Webreview - 8.2 Torque and Rotation Practice Test Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A 0.30-m-radius automobile

More information

The principle of the flywheel is found before the many centuries ago in spindle and the potter's wheel.

The principle of the flywheel is found before the many centuries ago in spindle and the potter's wheel. TOM Fly Wheel Mechanical Engineering Department The principle of the flywheel is found before the many centuries ago in spindle and the potter's wheel. A heavy-rimmed rotating wheel used to minimize variations

More information

Unit Workbook 4 - Level 4 ENG U8 Mechanical Principles 2018 UniCourse Ltd. All Rights Reserved. Sample

Unit Workbook 4 - Level 4 ENG U8 Mechanical Principles 2018 UniCourse Ltd. All Rights Reserved. Sample Pearson BTEC Level 4 Higher Nationals in Engineering (RQF) Unit 8: Mechanical Principles Unit Workbook 2 in a series of 4 for this unit Learning Outcome 2 Dynamic Mechanical Systems Page 1 of 17 1.3 Work

More information

Q.1 a) any six of the following 6x2= 12. i) Define - ( Each term 01 mark)

Q.1 a) any six of the following 6x2= 12. i) Define - ( Each term 01 mark) Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

The acceleration due to gravity g, which varies with latitude and height, will be approximated to 101m1s 2, unless otherwise specified.

The acceleration due to gravity g, which varies with latitude and height, will be approximated to 101m1s 2, unless otherwise specified. The acceleration due to gravity g, which varies with latitude and height, will be approximated to 101m1s 2, unless otherwise specified. F1 (a) The fulcrum in this case is the horizontal axis, perpendicular

More information

Rotation. PHYS 101 Previous Exam Problems CHAPTER

Rotation. PHYS 101 Previous Exam Problems CHAPTER PHYS 101 Previous Exam Problems CHAPTER 10 Rotation Rotational kinematics Rotational inertia (moment of inertia) Kinetic energy Torque Newton s 2 nd law Work, power & energy conservation 1. Assume that

More information

It will be most difficult for the ant to adhere to the wheel as it revolves past which of the four points? A) I B) II C) III D) IV

It will be most difficult for the ant to adhere to the wheel as it revolves past which of the four points? A) I B) II C) III D) IV AP Physics 1 Lesson 16 Homework Newton s First and Second Law of Rotational Motion Outcomes Define rotational inertia, torque, and center of gravity. State and explain Newton s first Law of Motion as it

More information

Class XI Chapter 7- System of Particles and Rotational Motion Physics

Class XI Chapter 7- System of Particles and Rotational Motion Physics Page 178 Question 7.1: Give the location of the centre of mass of a (i) sphere, (ii) cylinder, (iii) ring, and (iv) cube, each of uniform mass density. Does the centre of mass of a body necessarily lie

More information

Lecture 3. Rotational motion and Oscillation 06 September 2018

Lecture 3. Rotational motion and Oscillation 06 September 2018 Lecture 3. Rotational motion and Oscillation 06 September 2018 Wannapong Triampo, Ph.D. Angular Position, Velocity and Acceleration: Life Science applications Recall last t ime. Rigid Body - An object

More information

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A.

1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A. Code No: Z0321 / R07 Set No. 1 I B.Tech - Regular Examinations, June 2009 CLASSICAL MECHANICS ( Common to Mechanical Engineering, Chemical Engineering, Mechatronics, Production Engineering and Automobile

More information

= y(x, t) =A cos (!t + kx)

= y(x, t) =A cos (!t + kx) A harmonic wave propagates horizontally along a taut string of length L = 8.0 m and mass M = 0.23 kg. The vertical displacement of the string along its length is given by y(x, t) = 0. m cos(.5 t + 0.8

More information

DYNAMICS MOMENT OF INERTIA

DYNAMICS MOMENT OF INERTIA DYNAMICS MOMENT OF INERTIA S TO SELF ASSESSMENT EXERCISE No.1 1. A cylinder has a mass of 1 kg, outer radius of 0.05 m and radius of gyration 0.03 m. It is allowed to roll down an inclined plane until

More information

RIGID BODY MOTION (Section 16.1)

RIGID BODY MOTION (Section 16.1) RIGID BODY MOTION (Section 16.1) There are cases where an object cannot be treated as a particle. In these cases the size or shape of the body must be considered. Rotation of the body about its center

More information

Exam I Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion Today s lecture will cover Chapter 5 Exam I is Monday, Oct. 7 (2 weeks!

Exam I Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion Today s lecture will cover Chapter 5 Exam I is Monday, Oct. 7 (2 weeks! Exam I Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion http://www.youtube.com/watch?v=zyf5wsmxrai Today s lecture will cover Chapter 5 Exam I is Monday, Oct. 7 ( weeks!) Physics 101:

More information

Phys101 Lectures 19, 20 Rotational Motion

Phys101 Lectures 19, 20 Rotational Motion Phys101 Lectures 19, 20 Rotational Motion Key points: Angular and Linear Quantities Rotational Dynamics; Torque and Moment of Inertia Rotational Kinetic Energy Ref: 10-1,2,3,4,5,6,8,9. Page 1 Angular Quantities

More information

UNIT 2 KINEMATICS OF LINKAGE MECHANISMS

UNIT 2 KINEMATICS OF LINKAGE MECHANISMS UNIT 2 KINEMATICS OF LINKAGE MECHANISMS ABSOLUTE AND RELATIVE VELOCITY An absolute velocity is the velocity of a point measured from a fixed point (normally the ground or anything rigidly attached to the

More information

Uniform Circular Motion AP

Uniform Circular Motion AP Uniform Circular Motion AP Uniform circular motion is motion in a circle at the same speed Speed is constant, velocity direction changes the speed of an object moving in a circle is given by v circumference

More information

Circular Motion.

Circular Motion. 1 Circular Motion www.njctl.org 2 Topics of Uniform Circular Motion (UCM) Kinematics of UCM Click on the topic to go to that section Period, Frequency, and Rotational Velocity Dynamics of UCM Vertical

More information

AP Physics. Harmonic Motion. Multiple Choice. Test E

AP Physics. Harmonic Motion. Multiple Choice. Test E AP Physics Harmonic Motion Multiple Choice Test E A 0.10-Kg block is attached to a spring, initially unstretched, of force constant k = 40 N m as shown below. The block is released from rest at t = 0 sec.

More information

Mechanics Topic D (Rotation) - 1 David Apsley

Mechanics Topic D (Rotation) - 1 David Apsley TOPIC D: ROTATION SPRING 2019 1. Angular kinematics 1.1 Angular velocity and angular acceleration 1.2 Constant-angular-acceleration formulae 1.3 Displacement, velocity and acceleration in circular motion

More information

FALL TERM EXAM, PHYS 1211, INTRODUCTORY PHYSICS I Saturday, 14 December 2013, 1PM to 4 PM, AT 1003

FALL TERM EXAM, PHYS 1211, INTRODUCTORY PHYSICS I Saturday, 14 December 2013, 1PM to 4 PM, AT 1003 FALL TERM EXAM, PHYS 1211, INTRODUCTORY PHYSICS I Saturday, 14 December 2013, 1PM to 4 PM, AT 1003 NAME: STUDENT ID: INSTRUCTION 1. This exam booklet has 14 pages. Make sure none are missing 2. There is

More information

Uniform Circular Motion

Uniform Circular Motion Slide 1 / 112 Uniform Circular Motion 2009 by Goodman & Zavorotniy Slide 2 / 112 Topics of Uniform Circular Motion (UCM) Kinematics of UCM Click on the topic to go to that section Period, Frequency, and

More information

Name (please print): UW ID# score last first

Name (please print): UW ID# score last first Name (please print): UW ID# score last first Question I. (20 pts) Projectile motion A ball of mass 0.3 kg is thrown at an angle of 30 o above the horizontal. Ignore air resistance. It hits the ground 100

More information

PHYSICS 221, FALL 2011 EXAM #2 SOLUTIONS WEDNESDAY, NOVEMBER 2, 2011

PHYSICS 221, FALL 2011 EXAM #2 SOLUTIONS WEDNESDAY, NOVEMBER 2, 2011 PHYSICS 1, FALL 011 EXAM SOLUTIONS WEDNESDAY, NOVEMBER, 011 Note: The unit vectors in the +x, +y, and +z directions of a right-handed Cartesian coordinate system are î, ĵ, and ˆk, respectively. In this

More information

Chapter 9-10 Test Review

Chapter 9-10 Test Review Chapter 9-10 Test Review Chapter Summary 9.2. The Second Condition for Equilibrium Explain torque and the factors on which it depends. Describe the role of torque in rotational mechanics. 10.1. Angular

More information

K.GNANASEKARAN. M.E.,M.B.A.,(Ph.D)

K.GNANASEKARAN. M.E.,M.B.A.,(Ph.D) DEPARTMENT OF MECHANICAL ENGG. Engineering Mechanics I YEAR 2th SEMESTER) Two Marks Question Bank UNIT-I Basics and statics of particles 1. Define Engineering Mechanics Engineering Mechanics is defined

More information

Concept Question: Normal Force

Concept Question: Normal Force Concept Question: Normal Force Consider a person standing in an elevator that is accelerating upward. The upward normal force N exerted by the elevator floor on the person is 1. larger than 2. identical

More information

Uniform Circular Motion:-Circular motion is said to the uniform if the speed of the particle (along the circular path) remains constant.

Uniform Circular Motion:-Circular motion is said to the uniform if the speed of the particle (along the circular path) remains constant. Circular Motion:- Uniform Circular Motion:-Circular motion is said to the uniform if the speed of the particle (along the circular path) remains constant. Angular Displacement:- Scalar form:-?s = r?θ Vector

More information

General Definition of Torque, final. Lever Arm. General Definition of Torque 7/29/2010. Units of Chapter 10

General Definition of Torque, final. Lever Arm. General Definition of Torque 7/29/2010. Units of Chapter 10 Units of Chapter 10 Determining Moments of Inertia Rotational Kinetic Energy Rotational Plus Translational Motion; Rolling Why Does a Rolling Sphere Slow Down? General Definition of Torque, final Taking

More information

Textbook Reference: Wilson, Buffa, Lou: Chapter 8 Glencoe Physics: Chapter 8

Textbook Reference: Wilson, Buffa, Lou: Chapter 8 Glencoe Physics: Chapter 8 AP Physics Rotational Motion Introduction: Which moves with greater speed on a merry-go-round - a horse near the center or one near the outside? Your answer probably depends on whether you are considering

More information

P211 Spring 2004 Form A

P211 Spring 2004 Form A 1. A 2 kg block A traveling with a speed of 5 m/s as shown collides with a stationary 4 kg block B. After the collision, A is observed to travel at right angles with respect to the initial direction with

More information

Inertia Forces in Reciprocating. Parts. 514 l Theory of Machines

Inertia Forces in Reciprocating. Parts. 514 l Theory of Machines 514 l Theory of Machines 15 Features 1. Introduction.. Resultant Effect of a System of Forces Acting on a Rigid Body. 3. D-Alembert s Principle. 4. Velocity and Acceleration of the Reciprocating Parts

More information

Quantitative Skills in AP Physics 1

Quantitative Skills in AP Physics 1 This chapter focuses on some of the quantitative skills that are important in your AP Physics 1 course. These are not all of the skills that you will learn, practice, and apply during the year, but these

More information

Physics. Chapter 8 Rotational Motion

Physics. Chapter 8 Rotational Motion Physics Chapter 8 Rotational Motion Circular Motion Tangential Speed The linear speed of something moving along a circular path. Symbol is the usual v and units are m/s Rotational Speed Number of revolutions

More information

ISSUED BY K V - DOWNLOADED FROM KINEMATICS

ISSUED BY K V - DOWNLOADED FROM   KINEMATICS KINEMATICS *rest and Motion are relative terms, nobody can exist in a state of absolute rest or of absolute motion. *One dimensional motion:- The motion of an object is said to be one dimensional motion

More information

SAPTARSHI CLASSES PVT. LTD.

SAPTARSHI CLASSES PVT. LTD. SAPTARSHI CLASSES PVT. LTD. NEET/JEE Date : 13/05/2017 TEST ID: 120517 Time : 02:00:00 Hrs. PHYSICS, Chem Marks : 360 Phy : Circular Motion, Gravitation, Che : Halogen Derivatives Of Alkanes Single Correct

More information

VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING

VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR 603203 DEPARTMENT OF MECHANICAL ENGINEERING BRANCH: MECHANICAL YEAR / SEMESTER: I / II UNIT 1 PART- A 1. State Newton's three laws of motion? 2.

More information

We define angular displacement, θ, and angular velocity, ω. What's a radian?

We define angular displacement, θ, and angular velocity, ω. What's a radian? We define angular displacement, θ, and angular velocity, ω Units: θ = rad ω = rad/s What's a radian? Radian is the ratio between the length of an arc and its radius note: counterclockwise is + clockwise

More information

Chapter 8 Rotational Motion

Chapter 8 Rotational Motion Chapter 8 Rotational Motion Chapter 8 Rotational Motion In this chapter you will: Learn how to describe and measure rotational motion. Learn how torque changes rotational velocity. Explore factors that

More information

11. (7 points: Choose up to 3 answers) What is the tension,!, in the string? a.! = 0.10 N b.! = 0.21 N c.! = 0.29 N d.! = N e.! = 0.

11. (7 points: Choose up to 3 answers) What is the tension,!, in the string? a.! = 0.10 N b.! = 0.21 N c.! = 0.29 N d.! = N e.! = 0. A harmonic wave propagates horizontally along a taut string of length! = 8.0 m and mass! = 0.23 kg. The vertical displacement of the string along its length is given by!!,! = 0.1!m cos 1.5!!! +!0.8!!,

More information

Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion

Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion Physics 101: Lecture 08 Centripetal Acceleration and Circular Motion http://www.youtube.com/watch?v=zyf5wsmxrai Today s lecture will cover Chapter 5 Physics 101: Lecture 8, Pg 1 Circular Motion Act B A

More information

PSI AP Physics I Rotational Motion

PSI AP Physics I Rotational Motion PSI AP Physics I Rotational Motion Multiple-Choice questions 1. Which of the following is the unit for angular displacement? A. meters B. seconds C. radians D. radians per second 2. An object moves from

More information

PSI AP Physics I Rotational Motion

PSI AP Physics I Rotational Motion PSI AP Physics I Rotational Motion Multiple-Choice questions 1. Which of the following is the unit for angular displacement? A. meters B. seconds C. radians D. radians per second 2. An object moves from

More information

Physics. Student Materials Advanced Higher. Tutorial Problems Mechanics HIGHER STILL. Spring 2000

Physics. Student Materials Advanced Higher. Tutorial Problems Mechanics HIGHER STILL. Spring 2000 Spring 2000 HIGHER STILL Physics Student Materials Advanced Higher Tutorial Problems Mechanics TUTORIAL 1 You will find tutorials on each topic. The fully worked out answers are available. The idea is

More information

WEEK 1 Dynamics of Machinery

WEEK 1 Dynamics of Machinery WEEK 1 Dynamics of Machinery References Theory of Machines and Mechanisms, J.J. Uicker, G.R.Pennock ve J.E. Shigley, 2003 Makine Dinamiği, Prof. Dr. Eres SÖYLEMEZ, 2013 Uygulamalı Makine Dinamiği, Jeremy

More information

Tutorial 4. Figure 1: Rod and spindle. Dog. Figure 2: I have no idea what I m doing. Dog

Tutorial 4. Figure 1: Rod and spindle. Dog. Figure 2: I have no idea what I m doing. Dog Tutorial 4 Question 1 Figure 1: Rod and spindle A uniform disk rotates at 3.60 rev/s around a frictionless spindle. A non-rotating rod, of the same mass as the disk and equal in length to the disk s diameter,

More information

Slide 1 / 133. Slide 2 / 133. Slide 3 / How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m?

Slide 1 / 133. Slide 2 / 133. Slide 3 / How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? 1 How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? Slide 1 / 133 2 How many degrees are subtended by a 0.10 m arc of a circle of radius of 0.40 m? Slide 2 / 133 3 A ball rotates

More information

Slide 2 / 133. Slide 1 / 133. Slide 3 / 133. Slide 4 / 133. Slide 5 / 133. Slide 6 / 133

Slide 2 / 133. Slide 1 / 133. Slide 3 / 133. Slide 4 / 133. Slide 5 / 133. Slide 6 / 133 Slide 1 / 133 1 How many radians are subtended by a 0.10 m arc of a circle of radius 0.40 m? Slide 2 / 133 2 How many degrees are subtended by a 0.10 m arc of a circle of radius of 0.40 m? Slide 3 / 133

More information

Chapter 8 continued. Rotational Dynamics

Chapter 8 continued. Rotational Dynamics Chapter 8 continued Rotational Dynamics 8.4 Rotational Work and Energy Work to accelerate a mass rotating it by angle φ F W = F(cosθ)x x = rφ = Frφ Fr = τ (torque) = τφ r φ s F to x θ = 0 DEFINITION OF

More information

16.07 Dynamics Final Exam

16.07 Dynamics Final Exam Name:... Massachusetts Institute of Technology 16.07 Dynamics Final Exam Tuesday, December 20, 2005 Problem 1 (8) Problem 2 (8) Problem 3 (10) Problem 4 (10) Problem 5 (10) Problem 6 (10) Problem 7 (10)

More information

Suggested Problems. Chapter 1

Suggested Problems. Chapter 1 Suggested Problems Ch1: 49, 51, 86, 89, 93, 95, 96, 102. Ch2: 9, 18, 20, 44, 51, 74, 75, 93. Ch3: 4, 14, 46, 54, 56, 75, 91, 80, 82, 83. Ch4: 15, 59, 60, 62. Ch5: 14, 52, 54, 65, 67, 83, 87, 88, 91, 93,

More information

ME 6505 Dynamics of Machines

ME 6505 Dynamics of Machines LECTURE-I UNIT I - Force Analysis (1) Introduction: If the acceleration of moving links in a mechanism is running with considerable amount of linear and/or angular accelerations, inertia forces are generated

More information

Chapter 9. Rotational Dynamics

Chapter 9. Rotational Dynamics Chapter 9 Rotational Dynamics In pure translational motion, all points on an object travel on parallel paths. The most general motion is a combination of translation and rotation. 1) Torque Produces angular

More information

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5

CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 1 / 36 CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Date: 2 / 36 EQUATIONS OF MOTION: ROTATION

More information

Mechanics II. Which of the following relations among the forces W, k, N, and F must be true?

Mechanics II. Which of the following relations among the forces W, k, N, and F must be true? Mechanics II 1. By applying a force F on a block, a person pulls a block along a rough surface at constant velocity v (see Figure below; directions, but not necessarily magnitudes, are indicated). Which

More information

ME Machine Design I

ME Machine Design I ME 5 - Machine Design I Summer Semester 008 Name Lab. Div. EXAM. OEN BOOK AND CLOSED NOTES. Wednesday, July 16th, 008 Write your solutions on the blank paper that is provided. Write on one side of the

More information