Fire resistance simulation using LS-DYNA. Mikael Schill
|
|
- Darlene Jennings
- 5 years ago
- Views:
Transcription
1 Fire resistance simulation using LS-DYNA Mikael Schill
2 Background The aim of the simulations is to find the collapse of a structure due to fire The increase in temperature reduces the properties of the material and subsequently the critical load is reached Further, it is of interest to determine the position and amount of Passive Fire Protection (PFP) through FE-simulation Franssen, J.M. and Real, P.V. Fire design of steel structures, ECCS Eurocode Design Manuals, Ernst & Sohn, Berlin Gemany, 2010
3 Plastic Work Displacement Solver options Can be solved using either a coupled or un-coupled approach Thermal Solver Implicit Double precision Thermal Solver Implicit Double precision MPP/SMP Temperature ONLY SMP Temperature Mechanical Solver Implicit / Explicit Double precision / Single precision Mechanical Solver Implicit / Explicit Double precision / Single precision
4 Solver options Coupled solution: Staggered approach Mechanical t mech t mech Thermal t thermal t thermal t thermal Uncoupled approach Thermal Temperatures Mechanical
5 Mechanical and thermal properties Both a mechanical and a thermal material is needed Mechanical Young s Modulus Poisson s ratio Heat expansion Thermal Specific heat Thermal conductivity Yield stress Material hardening All input is temperaturedependent
6 Thermal Boundary conditions The heat flux is applied as a convective and/or a radiation boundary condition. q Total = q conv + q rad The convection/radiation coefficients can be prescribed as a function of time or as a function of the surrounding temperature.
7 Example: I beam Flexural-Torsional Collapse Paik, J., Czujko, J., Kim, J. Park, S., Islam, S. and Lee D. A New Procedure for the Nonlinear Strucural Response Analysis of Offshore Installations in Fires, SNAME Annual Meeting, Bellevue, Washington, 2013
8 Example: Simulation of topside Paik, J., Czujko, J., Kim, J. Park, S., Islam, S. and Lee D. A New Procedure for the Nonlinear Strucural Response Analysis of Offshore Installations in Fires, SNAME Annual Meeting, Bellevue, Washington, 2013
9 Passive Fire Protection (PFP) modeling In fire resistance simulation software, PFP (passive fire protection) is modeled using a convection function. Thus, the heat transfer is expressed as: q = h i (T s T e ) where T e is the temperature of the structure,t s is the temperature on the insulation surface and h i is the film coefficient (heat transfer coefficient). By this, it is assumed that the PFP has no thermal mass.
10 PFP modeling Solid elements The PFP can be modeled using one layer of solid elements. The thickness of the solid PFP element could be equal to the actual thickness of the PFP layer. The heat conduction, hc, of the PFP material is then calculated through: hc = h i t i where t i is the thickness of the PFP. If the solid elements are of different thickness than the PFP material, e.g. for pre-processing reasons, the heat conduction is calculated through: hc = h i t solid t i where t solid is the thickness of the solid element.
11 PFP modeling Shell elements The shell can be built up by several different materials through the thickness using *PART_COMPOSITE Mechanical material Thickness Thermal material Easy to vary the thickness of the PFP Reducing the number of elements Reducing the pre-postprocessing
12 PFP modeling PFP BEAM
13 I-Beam with PFP example All solids (coupled) Shells + Solid PFP(coupled) Composite PFP + Shells (uncoupled)
14 I-Beam with PFP example
15 I-Beam with PFP example
16 Conclusion Fire resistance simulations in LS-DYNA are performed using the thermal and implicit mechanical solvers. The solvers can be either coupled or un-coupled. LS-DYNA has a vast number of mechanical and thermal material models necessary to handle the temperature dependencies Passive Fire Protection (PFP) can be modeled using either solid elements or stacked shell elements for simple pre-processing.
17 Thank you! Your LS-DYNA distributor and more
*MAT_PAPER - a new orthotropic elastoplastic model for paper materials
*MAT_PAPER - a new orthotropic elastoplastic model for paper materials Jesper Karlsson, Dynamore Nordic Mikael Schill, Dynamore Nordic Johan Tryding, Tetra Pak *MAT_PAPER (*MAT_274) A new orthotropic elastoplastic
More informationSIMPLIFIED MODELING OF THIN-WALLED TUBES WITH OCTAGONAL CROSS SECTION AXIAL CRUSHING. Authors and Correspondance: Abstract:
SIMPLIFIED MODELING OF THIN-WALLED TUBES WITH OCTAGONAL CROSS SECTION AXIAL CRUSHING Authors and Correspondance: Yucheng Liu, Michael L. Day Department of Mechanical Engineering University of Louisville
More informationThomas Johansson DYNAmore Nordic AB. Drop Test Simulation
Thomas Johansson DYNAmore Nordic AB Drop Test Simulation Plastic Work Displacement LS-DYNA solve all your applications One Code for Multi-Physics Solutions Thermal Solver Implicit Double precision EM Solver
More informationCollapse behaviour and simplified modeling of triangular cross-section columns
Indian Journal of ngineering & Materials Sciences Vol. 16, April 2009, pp. 71-78 Collapse behaviour and simplified ing of triangular cross-section columns Yucheng Liu* Department of Mechanical ngineering,
More informationLecture 9 Thermal Analysis
Lecture 9 Thermal Analysis 16.0 Release Introduction to ANSYS Mechanical 1 2015 ANSYS, Inc. February 27, 2015 Chapter Overview In this chapter, performing steady-state thermal analyses in Mechanical will
More informationMEG 795 COURSE PROJECT
MEG 795 COURSE PROJECT Transient dynamic analysis of a 3 Point Impact Hammer Test on a simply supported steel plate using ANSYS and LS-DYNA JAGANNADHA RAO NARAPARAJU DEPARTMENT OF MECHANICAL ENGINEERING
More informationExample 37 - Analytical Beam
Example 37 - Analytical Beam Summary This example deals with the use of RADIOSS linear and nonlinear solvers. A beam submitted to a concentrated load on one extremity and fixed on the other hand is studied.
More informationCoupling of the EM Solver with Mechanical and Thermal Shell Elements
13 th International LS-DYNA Users Conference Session: Electromagnetic Coupling of the EM Solver with Mechanical and Thermal Shell Elements Pierre L Eplattenier Julie Anton Iñaki Çaldichoury Livermore Software
More informationStructural behaviour of structures in fire
Structural behaviourof structures in fire Tomaž Hozjan Faculty of civil and geodetic engineering University of Ljubljana, Slovenia Lesław Kwaśniewski Warsaw University of Technology, Poland PLAN FOR PRESENTATION
More informationTHE S-S CURVE APPROXIMATION FOR GFRP TENSILE SPECIMEN BY USING INVERSE METHOD AND OPTIMIZATION
THE S-S CURVE APPROXIMATION FOR GFRP TENSILE SPECIMEN BY USING INVERSE METHOD AND OPTIMIZATION D. S. Shin and E. S. Jeon Department of Mechanical Engineering, Kongju National University, Korea E-Mail:
More informationEQUIVALENT FRACTURE ENERGY CONCEPT FOR DYNAMIC RESPONSE ANALYSIS OF PROTOTYPE RC GIRDERS
EQUIVALENT FRACTURE ENERGY CONCEPT FOR DYNAMIC RESPONSE ANALYSIS OF PROTOTYPE RC GIRDERS Abdul Qadir Bhatti 1, Norimitsu Kishi 2 and Khaliq U Rehman Shad 3 1 Assistant Professor, Dept. of Structural Engineering,
More informationNumerical simulation the bottom structures. grounding test by LS-DYNA
5 th European LS-DYNA Users Conference Methods and Techniques (3) Numerical simulation the bottom structures grounding test by LS-DYNA Ainian Zhang Graduate School of Frontier Sciences, The University
More informationInfluence of residual stresses in the structural behavior of. tubular columns and arches. Nuno Rocha Cima Gomes
October 2014 Influence of residual stresses in the structural behavior of Abstract tubular columns and arches Nuno Rocha Cima Gomes Instituto Superior Técnico, Universidade de Lisboa, Portugal Contact:
More informationFinite Element Modelling with Plastic Hinges
01/02/2016 Marco Donà Finite Element Modelling with Plastic Hinges 1 Plastic hinge approach A plastic hinge represents a concentrated post-yield behaviour in one or more degrees of freedom. Hinges only
More informationValidation of the Advanced Calculation Model SAFIR Through DIN EN Procedure
Validation of the Advanced Calculation Model SAFIR Through DIN EN 1991-1-2 Procedure Raul Zaharia Department of Steel Structures and Structural Mechanics The Politehnica University of Timisoara, Ioan Curea
More informationFEA A Guide to Good Practice. What to expect when you re expecting FEA A guide to good practice
FEA A Guide to Good Practice What to expect when you re expecting FEA A guide to good practice 1. Background Finite Element Analysis (FEA) has transformed design procedures for engineers. Allowing more
More informationNUMERICAL EVALUATION OF THE ROTATIONAL CAPACITY OF STEEL BEAMS AT ELEVATED TEMPERATURES
8 th GRACM International Congress on Computational Mechanics Volos, 12 July 15 July 2015 NUMERICAL EVALUATION OF THE ROTATIONAL CAPACITY OF STEEL BEAMS AT ELEVATED TEMPERATURES Savvas Akritidis, Daphne
More informationCourse in. Geometric nonlinearity. Nonlinear FEM. Computational Mechanics, AAU, Esbjerg
Course in Nonlinear FEM Geometric nonlinearity Nonlinear FEM Outline Lecture 1 Introduction Lecture 2 Geometric nonlinearity Lecture 3 Material nonlinearity Lecture 4 Material nonlinearity it continued
More informationSAFIR MANUAL. Material Properties
Faculté des Sciences Appliquées Département d Architecture, Géologie, Environnement & Constructions Structural Engineering SAFIR MANUAL Material Properties July 2016 Thomas GERNAY Jean-Marc FRANSSEN Université
More informationModeling Hailstone Impact onto Composite Material Panel Under a Multi-axial State of Stress
Modeling Hailstone Impact onto Composite Material Panel Under a Multi-axial State of Stress Authors Marco ANGHILERI * Luigi-M L CASTELLETTI * Andrea MILANESE * and Andrea SEMBOLONI * Affiliation * Politecnico
More informationMulti Linear Elastic and Plastic Link in SAP2000
26/01/2016 Marco Donà Multi Linear Elastic and Plastic Link in SAP2000 1 General principles Link object connects two joints, i and j, separated by length L, such that specialized structural behaviour may
More informationModelling and numerical simulation of the wrinkling evolution for thermo-mechanical loading cases
Modelling and numerical simulation of the wrinkling evolution for thermo-mechanical loading cases Georg Haasemann Conrad Kloß 1 AIMCAL Conference 2016 MOTIVATION Wrinkles in web handling system Loss of
More informationUltimate shear strength of FPSO stiffened panels after supply vessel collision
Ultimate shear strength of FPSO stiffened panels after supply vessel collision Nicolau Antonio dos Santos Rizzo PETROBRAS Rio de Janeiro Brazil Marcelo Caire SINTEF do Brasil Rio de Janeiro Brazil Carlos
More informationSECTION 1. Introduction to MD NASTRAN SOL 400
SECTION 1 Introduction to MD NASTRAN SOL 400 S1-1 S1-2 What is "MD NASTRAN"? Evolution of engineering challenges: Complex systems vs. "just parts" Interacting environments Disparate tools and databases
More informationUniversity of Sheffield The development of finite elements for 3D structural analysis in fire
The development of finite elements for 3D structural analysis in fire Chaoming Yu, I. W. Burgess, Z. Huang, R. J. Plank Department of Civil and Structural Engineering StiFF 05/09/2006 3D composite structures
More informationFire Analysis of Reinforced Concrete Beams with 2-D Plane Stress Concrete Model
Research Journal of Applied Sciences, Engineering and Technology 5(2): 398-44, 213 ISSN: 24-7459; E-ISSN: 24-7467 Maxwell Scientific Organization, 213 Submitted: April 29, 212 Accepted: May 23, 212 Published:
More informationDesign issues of thermal induced effects and temperature dependent material properties in Abaqus
Materials Characterisation VII 343 Design issues of thermal induced effects and temperature dependent material properties in Abaqus I. Both 1, F. Wald 1 & R. Zaharia 2 1 Department of Steel and Timber
More informationTHE EFFECT OF GEOMETRY ON FATIGUE LIFE FOR BELLOWS
Advanced Materials Development and Performance (AMDP2011) International Journal of Modern Physics: Conference Series Vol. 6 (2012) 343-348 World Scientific Publishing Company DOI: 10.1142/S2010194512003418
More informationPROGRAMMING THE TRANSIENT EXPLICIT FINITE ELEMENT ANALYSIS WITH MATLAB
U.P.B. Sci. Bull., Series D, Vol. 75, Iss. 2, 2013 ISSN 1454-2358 PROGRAMMING THE TRANSIENT EXPLICIT FINITE ELEMENT ANALYSIS WITH MATLAB Andrei Dragoş Mircea SÎRBU 1, László FARKAS 2 Modern research in
More informationChapter 4 Analysis of a cantilever
Chapter 4 Analysis of a cantilever Before a complex structure is studied performing a seismic analysis, the behaviour of simpler ones should be fully understood. To achieve this knowledge we will start
More informationAn Increase in Elastic Buckling Strength of Plate Girder by the Influence of Transverse Stiffeners
GRD Journals- Global Research and Development Journal for Engineering Volume 2 Issue 6 May 2017 ISSN: 2455-5703 An Increase in Elastic Buckling Strength of Plate Girder by the Influence of Transverse Stiffeners
More informationThe Key Laboratory of Urban Security and Disaster Engineering of Ministry of Education, Beijing University of Technology, Beijing , China
Send Orders for Reprin to reprin@benthamscience.ae 688 The Open Civil Engineering Journal, 205, 9, 688-692 Open Access Numerical Simulation of a Subway Station Structure Subjected to Terrorism Bombing
More informationThick Shell Element Form 5 in LS-DYNA
Thick Shell Element Form 5 in LS-DYNA Lee P. Bindeman Livermore Software Technology Corporation Thick shell form 5 in LS-DYNA is a layered node brick element, with nodes defining the boom surface and defining
More informationExperimental and numerical studies of the effect of high temperature to the steel structure
Experimental and numerical studies of the effect of high temperature to the steel structure LENKA LAUSOVÁ IVETA SKOTNICOVÁ IVAN KOLOŠ MARTIN KREJSA Faculty of Civil Engineering VŠB-Technical University
More informationCoupled Thermomechanical Contact Problems
Coupled Thermomechanical Contact Problems Computational Modeling of Solidification Processes C. Agelet de Saracibar, M. Chiumenti, M. Cervera ETS Ingenieros de Caminos, Canales y Puertos, Barcelona, UPC
More informationThermal Analysis with SOLIDWORKS Simulation 2016 and Flow Simulation 2016
Thermal Analysis with SOLIDWORKS Simulation 2016 and Flow Simulation 2016 Paul M. Kurowski SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
More informationMATERIAL MECHANICS, SE2126 COMPUTER LAB 2 PLASTICITY
MATERIAL MECHANICS, SE2126 COMPUTER LAB 2 PLASTICITY PART A INTEGRATED CIRCUIT An integrated circuit can be thought of as a very complex maze of electronic components and metallic connectors. These connectors
More informationAXIAL BUCKLING RESISTANCE OF PARTIALLY ENCASED COLUMNS
Proceedings of the 5th International Conference on Integrity-Reliability-Failure, Porto/Portugal 24-28 July 2016 Editors J.F. Silva Gomes and S.A. Meguid Publ. INEGI/FEUP (2016) PAPER REF: 6357 AXIAL BUCKLING
More informationExperimentally Calibrating Cohesive Zone Models for Structural Automotive Adhesives
Experimentally Calibrating Cohesive Zone Models for Structural Automotive Adhesives Mark Oliver October 19, 2016 Adhesives and Sealants Council Fall Convention contact@veryst.com www.veryst.com Outline
More information8/1/2009. CAE 7962 Presentation
CAE 7962 Presentation Gavin Patey Dameion Moores Aaron Henstridge Ashley Burke Brendan Harvey Fabio Faragalli Introduction Choosing mesh properties Explanation of the types of studies available and the
More informationAn Evaluation and Comparison of Models for Maximum Deflection of Stiffened Plates Using Finite Element Analysis
Marine Technology, Vol. 44, No. 4, October 2007, pp. 212 225 An Evaluation and Comparison of Models for Maximum Deflection of Stiffened Plates Using Finite Element Analysis Lior Banai 1 and Omri Pedatzur
More informationSeismic Assessment of a RC Building according to FEMA 356 and Eurocode 8
1 Seismic Assessment of a RC Building according to FEMA 356 and Eurocode 8 Ioannis P. GIANNOPOULOS 1 Key words: Pushover analysis, FEMA 356, Eurocode 8, seismic assessment, plastic rotation, limit states
More informationALASKA ENERGY AUTHORITY AEA ENGINEERING FEASIBILITY REPORT. Appendix B8. Finite Element Analysis
ALASKA ENERGY AUTHORITY AEA11-022 ENGINEERING FEASIBILITY REPORT Appendix B8 Finite Element Analysis Susitna-Watana Hydroelectric Project Alaska Energy Authority FERC Project No. 14241 December 2014 Seismic
More information3D Finite Element analysis of stud anchors with large head and embedment depth
3D Finite Element analysis of stud anchors with large head and embedment depth G. Periškić, J. Ožbolt & R. Eligehausen Institute for Construction Materials, University of Stuttgart, Stuttgart, Germany
More informationMODELING THE EFFECTIVE ELASTIC MODULUS OF RC BEAMS EXPOSED TO FIRE
Journal of Marine Science and Technology, Vol., No., pp. -8 () MODELING THE EFFECTIVE ELASTIC MODULUS OF RC BEAMS EXPOSED TO FIRE Jui-Hsiang Hsu*, ***, Cherng-Shing Lin**, and Chang-Bin Huang*** Key words:
More informationUSER S MANUAL 1D Seismic Site Response Analysis Example University of California: San Diego August 30, 2017
USER S MANUAL 1D Seismic Site Response Analysis Example http://www.soilquake.net/ucsdsoilmodels/ University of California: San Diego August 30, 2017 Table of Contents USER'S MANUAL TABLE OF CONTENTS Page
More informationAutomatic Buckling Checks on Stiffened Panels Based on Finite Element Results
Delft University of Technology Faculty of Civil Engineering & Geosciences Department of Structural Mechanics Automatic Buckling Checks on Stiffened Panels Based on Finite Element Results Master Thesis
More informationThe 10 th international Energy Conference (IEC 2014)
Ultimate Limit State Assessments of Steel Plates for Spar-Type Floating Offshore Wind Turbines 1. Sajad Rahmdel 1) 2. Hyerin Kwon 2) 3. Seonghun Park 3) 1), 2), 3) School of Mechanical Engineering, Pusan
More informationTORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES)
Page1 TORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES) Restrained warping for the torsion of thin-wall open sections is not included in most commonly used frame analysis programs. Almost
More informationANALYSIS OF THERMAL STRESSES OF SOLAR PARABOLIC TROUGH COLLECTOR FOR SOLAR POWER PLANT BY FEM
Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 2, April, 2014 2014 IJMERR. All Rights Reserved ANALYSIS OF THERMAL STRESSES OF SOLAR PARABOLIC TROUGH COLLECTOR FOR SOLAR POWER PLANT BY FEM K
More informationParametric Studies of Low Velocity Impact on E-glass/Epoxy using Ls-Dyna
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 11, Issue 4 Ver. V (Jul- Aug. 2014), PP 33-39 Parametric Studies of Low Velocity Impact on E-glass/Epoxy
More informationFINITE ELEMENT ANALYSIS OF TAPERED COMPOSITE PLATE GIRDER WITH A NON-LINEAR VARYING WEB DEPTH
Journal of Engineering Science and Technology Vol. 12, No. 11 (2017) 2839-2854 School of Engineering, Taylor s University FINITE ELEMENT ANALYSIS OF TAPERED COMPOSITE PLATE GIRDER WITH A NON-LINEAR VARYING
More informationDISPENSA FEM in MSC. Nastran
DISPENSA FEM in MSC. Nastran preprocessing: mesh generation material definitions definition of loads and boundary conditions solving: solving the (linear) set of equations components postprocessing: visualisation
More informationSIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE
SIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE M.A. Youssef a, S.F. El-Fitiany a a Western University, Faculty of Engineering, London, Ontario, Canada Abstract Structural
More informationTheoretical Manual Theoretical background to the Strand7 finite element analysis system
Theoretical Manual Theoretical background to the Strand7 finite element analysis system Edition 1 January 2005 Strand7 Release 2.3 2004-2005 Strand7 Pty Limited All rights reserved Contents Preface Chapter
More informationMicro-meso draping modelling of non-crimp fabrics
Micro-meso draping modelling of non-crimp fabrics Oleksandr Vorobiov 1, Dr. Th. Bischoff 1, Dr. A. Tulke 1 1 FTA Forschungsgesellschaft für Textiltechnik mbh 1 Introduction Non-crimp fabrics (NCFs) are
More informationLateral Crushing of Square and Rectangular Metallic Tubes under Different Quasi-Static Conditions
Vol:, No:1, 2 Lateral Crushing of Square and Rectangular Metallic Tubes under Different Quasi-Static Conditions Sajjad Dehghanpour, Ali Yousefi International Science Index, Mechanical and Mechatronics
More informationFE analysis of steel-concrete composite structure with partial interactions
FE analysis of steel-concrete composite structure with partial interactions WonHo Lee 1), SeoJun Ju 2) and Hyo-Gyoung Kwa 3) 1), 2) 3) Department of Civil Engineering, KAIST, Daejeon 34141, Korea 1) wonho.lee@aist.ac.r
More informationNumerical simulation of sheet metal forming processes using a new yield criterion
Key Engineering Materials Vol. 344 (007) pp. 833-840 online at http://www.scientific.net (007) Trans Tech Publications, Switzerland Numerical simulation of sheet metal forming processes using a new yield
More informationA Constitutive Model for DYNEEMA UD composites
A Constitutive Model for DYNEEMA UD composites L Iannucci 1, D J Pope 2, M Dalzell 2 1 Imperial College, Department of Aeronautics London, SW7 2AZ l.iannucci@imperial.ac.uk 2 Dstl, Porton Down, Salisbury,
More informationPREDICTIVE SIMULATION OF UNDERWATER IMPLOSION: Coupling Multi-Material Compressible Fluids with Cracking Structures
PREDICTIVE SIMULATION OF UNDERWATER IMPLOSION: Coupling Multi-Material Compressible Fluids with Cracking Structures Kevin G. Wang Virginia Tech Patrick Lea, Alex Main, Charbel Farhat Stanford University
More informationWP7 GUIDELINE FOR GLOBAL STRUCTURAL ANALYSIS USING NEW BEAM-COLUMN FINITE ELEMENT
WP7 GUIDELINE FOR GLOBAL STRUCTURAL ANALYSIS USING NEW BEAM-COLUMN FINITE ELEMENT 1 Table of contents 1 Introduction... 4 1.1 Reminder on the background for class 4 cross-sections analysis in fire... 4
More informationMODELING OF ELASTO-PLASTIC MATERIALS IN FINITE ELEMENT METHOD
MODELING OF ELASTO-PLASTIC MATERIALS IN FINITE ELEMENT METHOD Andrzej Skrzat, Rzeszow University of Technology, Powst. Warszawy 8, Rzeszow, Poland Abstract: User-defined material models which can be used
More informationPOST-BUCKLING CAPACITY OF BI-AXIALLY LOADED RECTANGULAR STEEL PLATES
POST-BUCKLING CAPACITY OF BI-AXIALLY LOADED RECTANGULAR STEEL PLATES Jeppe Jönsson a and Tommi H. Bondum b a,b DTU Civil Engineering, Technical University of Denmark Abstract: Results from a detailed numerical
More informationCOURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 3013 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6
COURSE TITLE : THEORY OF STRUCTURES -I COURSE CODE : 0 COURSE CATEGORY : B PERIODS/WEEK : 6 PERIODS/SEMESTER: 90 CREDITS : 6 TIME SCHEDULE Module Topics Period Moment of forces Support reactions Centre
More informationPART 2 THERMAL RESPONSE. DIF SEK Part 2: Thermal Response 0/ 44
DIF SEK PART 2 THERMAL RESPONSE DIF SEK Part 2: Thermal Response 0/ 44 Resistance to fire - Chain of events Θ Loads 1: Ignition Steel columns time 2: Thermal action 3: Mechanical actions R 4: Thermal response
More informationAiMT Advances in Military Technology
AiMT Advances in Military Technology Vol. 13, No. 1 (2018), pp. 33-45 ISSN 1802-2308, eissn 2533-4123 DOI 10.3849/aimt.01213 Identification of Concrete Material Model Parameters P. Král 1*, M. Hušek 1,
More informationANALYSIS OF THE INTERACTIVE BUCKLING IN STIFFENED PLATES USING A SEMI-ANALYTICAL METHOD
EUROSTEEL 2014, September 10-12, 2014, Naples, Italy ANALYSIS OF THE INTERACTIVE BUCKLING IN STIFFENED PLATES USING A SEMI-ANALYTICAL METHOD Pedro Salvado Ferreira a, Francisco Virtuoso b a Polytechnic
More informationUpon Impact Numerical Modeling of Foam Materials
Upon Impact Numerical Modeling of Foam Materials VASILE NASTASESCU*, SILVIA MARZAVAN Military Technical Academy, 81-83 George Cosbuc Blvd., 050141, Bucharest, Romania The paper presents some theoretical
More informationAn Advanced Technology for Structural Crashworthiness Analysis of a Ship Colliding with an Ice-Ridge: Numerical Modelling and Experiments
An Advanced Technology for Structural Crashworthiness Analysis of a Ship Colliding with an Ice-Ridge: Numerical Modelling and Experiments Serdar Turgut Ince 1, Ankush Kumar 2, DaeKyeom Park 3 and JeomKee
More informationOPTIMAL SHAKEDOWN ANALYSIS OF LATERALLY LOADED PILE WITH LIMITED RESIDUAL STRAIN ENERGY
INTERNATIONAL JOURNAL OF OPTIMIZATION IN CIVIL ENGINEERING Int. J. Optim. Civil Eng., 2018; 8(3):347-355 OPTIMAL SHAKEDOWN ANALYSIS OF LATERALLY LOADED PILE WITH LIMITED RESIDUAL STRAIN ENERGY M. Movahedi
More informationProject Name Structural Calculation for Feature Pressing
Project Name Structural Calculation for Feature Pressing Presented to: Client Logo Revision Generated by Date Reviewed by Date Comment 0 1 2 3 Table of Contents 1.0 Introduction & Loadings... 3 1.1 Introduction
More informationCalibration and Experimental Validation of LS-DYNA Composite Material Models by Multi Objective Optimization Techniques
9 th International LS-DYNA Users Conference Optimization Calibration and Experimental Validation of LS-DYNA Composite Material Models by Multi Objective Optimization Techniques Stefano Magistrali*, Marco
More informationCHAPTER 8: Thermal Analysis
CHAPER 8: hermal Analysis hermal Analysis: calculation of temperatures in a solid body. Magnitude and direction of heat flow can also be calculated from temperature gradients in the body. Modes of heat
More informationNonlinear Finite Element Modeling of Nano- Indentation Group Members: Shuaifang Zhang, Kangning Su. ME 563: Nonlinear Finite Element Analysis.
ME 563: Nonlinear Finite Element Analysis Spring 2016 Nonlinear Finite Element Modeling of Nano- Indentation Group Members: Shuaifang Zhang, Kangning Su Department of Mechanical and Nuclear Engineering,
More informationStrain Measurement. Prof. Yu Qiao. Department of Structural Engineering, UCSD. Strain Measurement
Strain Measurement Prof. Yu Qiao Department of Structural Engineering, UCSD Strain Measurement The design of load-carrying components for machines and structures requires information about the distribution
More informationprepared checked approved Date: Date: Date: S. Fahrendholz/R.Geiger Dr.-Ing. Jürgen Bellmann Dr.-Ing.
Verification Manual Version 12.2 2009 prepared checked approved Date: 01.08.2003 Date: 19.01.2009 Date: 22.01.2009 S. Fahrendholz/R.Geiger Dr.Ing. Jürgen Bellmann Dr.Ing. Casimir Katz Document name: q:\dok\qs\verification.doc
More informationCHAPTER 4 DESIGN AND ANALYSIS OF CANTILEVER BEAM ELECTROSTATIC ACTUATORS
61 CHAPTER 4 DESIGN AND ANALYSIS OF CANTILEVER BEAM ELECTROSTATIC ACTUATORS 4.1 INTRODUCTION The analysis of cantilever beams of small dimensions taking into the effect of fringing fields is studied and
More informationNonlinear Analysis of Reinforced Concrete Shells Subjected to Impact Loads
Transactions of the 7 th International Conference on Structural Mechanics in Reactor Technology (SMiRT 7) Prague, Czech Republic, August 7, 00 Paper # J0- Nonlinear Analysis of Reinforced Concrete Shells
More informationSimulation of flow induced vibrations in pipes using the LS-DYNA ICFD solver
Simulation of flow induced vibrations in pipes using the LS-DYNA ICFD solver arcus Timgren 1 1 DYNAmore Nordic AB, Linköping, Sweden 1 Introduction Flow-induced vibrations, (FIV), is a terminology that
More informationChapter 6: Mechanical Properties of Metals. Dr. Feras Fraige
Chapter 6: Mechanical Properties of Metals Dr. Feras Fraige Stress and Strain Tension Compression Shear Torsion Elastic deformation Plastic Deformation Yield Strength Tensile Strength Ductility Toughness
More informationA Thesis Proposal. Agrawal, Ravi. Submitted to the Office of Graduate Studies of Texas A&M University
Using Finite Element Structural Analysis of Retroreflective Raised Pavement Markers (RRPMs) to Recommend Testing Procedures for Simulating Field Performance of RRPMs A Thesis Proposal By Agrawal, Ravi
More informationUpdate On The Electromagnetism Module In LS-DYNA
12 th International LS-DYNA Users Conference Electromagnetic(1) Update On The Electromagnetism Module In LS-DYNA Pierre L'Eplattenier Iñaki Çaldichoury Livermore Software Technology Corporation 7374 Las
More informationImpact Analysis of Frontal Car Bumper using Long Fibre Reinforced Thermoplastics
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2015INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Impact
More informationBuckling Resistance Assessment of a Slender Cylindrical Shell Axially Compressed
Mechanics and Mechanical Engineering Vol. 14, No. 2 (2010) 309 316 c Technical University of Lodz Buckling Resistance Assessment of a Slender Cylindrical Shell Axially Compressed Jakub Marcinowski Institute
More informationEffect of Specimen Dimensions on Flexural Modulus in a 3-Point Bending Test
Effect of Specimen Dimensions on Flexural Modulus in a 3-Point Bending Test M. Praveen Kumar 1 and V. Balakrishna Murthy 2* 1 Mechanical Engineering Department, P.V.P. Siddhartha Institute of Technology,
More informationEARLY AGE THERMAL CRACK CONTROL IN MASS CONCRETE
EARLY AGE THERMAL CRACK CONTROL IN MASS CONCRETE A.W.R.M.G.W.D.B. Girihagama * and S.M.A. Nanayakkara University of Moratuwa, Colombo, Sri Lanka *E-mail: danu.girihagama.uom @ gmail.com, TP: +94711352729
More informationUsing Thermal Boundary Conditions in SOLIDWORKS Simulation to Simulate a Press Fit Connection
Using Thermal Boundary Conditions in SOLIDWORKS Simulation to Simulate a Press Fit Connection Simulating a press fit condition in SOLIDWORKS Simulation can be very challenging when there is a large amount
More informationCalculus of the Elastic Properties of a Beam Cross-Section
Presented at the COMSOL Conference 2009 Milan Calculus of the Elastic Properties of a Beam Cross-Section Dipartimento di Modellistica per l Ingegneria Università degli Studi della Calabria (Ital) COMSOL
More informationProject. First Saved Monday, June 27, 2011 Last Saved Wednesday, June 29, 2011 Product Version 13.0 Release
Project First Saved Monday, June 27, 2011 Last Saved Wednesday, June 29, 2011 Product Version 13.0 Release Contents Units Model (A4, B4) o Geometry! Solid Bodies! Parts! Parts! Body Groups! Parts! Parts
More informationCOMPARISON OF EXPERIMENTAL RESULTS WITH FEM ONES OF RECTANGULAR CFRP TUBES FOR FRONT SIDE MEMBERS OF AUTOMOBILES
16 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS COMPARISON OF EXPERIMENTAL RESULTS WITH FEM ONES OF RECTANGULAR CFRP TUBES FOR FRONT SIDE MEMBERS OF AUTOMOBILES Hyoung-Soo Kim*, Goichi Ben**,Yoshio
More informationAdvanced Analysis of Steel Structures
Advanced Analysis of Steel Structures Master Thesis Written by: Maria Gulbrandsen & Rasmus Petersen Appendix Report Group B-204d M.Sc.Structural and Civil Engineering Aalborg University 4 th Semester Spring
More informationA Study on the Tube of Integral Propeller Shaft for the Rear-wheel Drive Automobile Using Carbon Composite Fiber
A Study on the Tube of Integral Propeller Shaft for the Rear-wheel Drive Automobile Using Carbon Composite Fiber Kibong Han Mechatronics Department, Jungwon University, 85 Munmu-ro, Goesan-gun, South Korea.
More informationPARAMETRIC STUDY OF THE STRUCTURAL CAPACITY OF REINFORCED CONCRETE CONTAINMENT SUBJECTED TO LARGE COMMERICAL AIRCRFAT IMPACT
Transactions, SMiRT-23, Paper 285 PARAMETRIC STUDY OF THE STRUCTURAL CAPACITY OF REINFORCED CONCRETE CONTAINMENT SUBJECTED TO LARGE COMMERICAL AIRCRFAT IMPACT Marin Kostov 1, Milko Miloshev 2, Zhivko Nikolov
More informationExternal Pressure... Thermal Expansion in un-restrained pipeline... The critical (buckling) pressure is calculated as follows:
External Pressure... The critical (buckling) pressure is calculated as follows: P C = E. t s ³ / 4 (1 - ν ha.ν ah ) R E ³ P C = Critical buckling pressure, kn/m² E = Hoop modulus in flexure, kn/m² t s
More informationULTIMATE STRENGTH OF SQUARE PLATE WITH RECTANGULAR OPENING UNDER AXIAL COMPRESSION
Journal of Naval Architecture and Marine Engineering June, 2007 http://jname.8m.net ULTIMATE STRENGTH OF SQUARE PLATE WITH RECTANGULAR OPENING UNDER AXIAL COMPRESSION M. Suneel Kumar 1*, P. Alagusundaramoorthy
More informationExperimental Study and Numerical Simulation on Steel Plate Girders With Deep Section
6 th International Conference on Advances in Experimental Structural Engineering 11 th International Workshop on Advanced Smart Materials and Smart Structures Technology August 1-2, 2015, University of
More informationPerformance Evaluation of Fu Chang and Low Density Foam Model for Expanded Polypropylene
MIT International Journal of Mechanical Engineering, Vol. 4, No. 1, January 2014, pp. 49 53 49 Performance Evaluation of Fu Chang and Low Density Foam Model for Expanded Polypropylene Vivek Srivastava
More informationAn Assessment of the LS-DYNA Hourglass Formulations via the 3D Patch Test
5 th European LS-DYNA Users Conference Code Developments An Assessment of the LS-DYNA Hourglass Formulations via the 3D Patch Test Authors Leonard E. Schwer, Schwer, Engineering & Consulting Services Samuel
More informationExperience from using recently implemented enhancements for Material 36 in LS-DYNA 971 performing a virtual tensile test. Authors: Correspondence:
Experience from using recently implemented enhancements for Material 36 in LS-DYNA 971 performing a virtual tensile test Authors: Michael Fleischer BMW Group Thomas Borrvall Engineering Research Nordic
More information