Parametric Study and Optimization of WEDM Parameters for Titanium diboride TiB2

Size: px
Start display at page:

Download "Parametric Study and Optimization of WEDM Parameters for Titanium diboride TiB2"

Transcription

1 Parametric Study and Optimization of WEDM Parameters for Titanium diboride TiB2 Pravin R. Kubade 1, Sunil S. Jamadade 2, Rahul C. Bhedasgaonkar 3, Rabiya Attar 4, Naval Solapure 5, Ulka Vanarase 6, Sayali Patil 7 1 Assistant Professor, Dept. of Production Engg., KIT s COE Kolhapur, Maharashtra, India 2,4 Assistant Professor, Dept. of Mechanical Engg., KIT s COE Kolhapur, Maharashtra, India 4-7 U.G. Scholars, Dept. of Production Engg., KIT s COE Kolhapur, Maharashtra, India *** Abstract - Wire electrical discharge machining (WEDM) is used in industry for machining complex profiles with high accuracy in conductive material. In the present work, the parametric optimization method using Taguchi method is proposed for WEDM of Titanium diboride TiB2 component. Three process parameters are selected for this investigation; Pulse ontime, Pulse off-time and wire feed. The experimentation is conducted by using Taguchi s L27 orthogonal array. Signal to Noise ratios of the Material removal rate, Surface roughness and Overcut for all experiments are calculated. The results are analyzed using analysis of variance (ANOVA) and response graphs and presented. Keywords: WEDM, Pulse on-time, Pulse off-time, TiB 2. Key Words: TiB 2, etc 1. INTRODUCTION WEDM, Pulse on-time, Pulse off-time, amount of clamping pressure required to hold small, thin and fragile parts is minimal, preventing damage or distortion to the work-piece. The accuracy, surface finish and time required to complete a job is extremely predictable, making it much easier to quote; WEDM leaves a totally random pattern on the surface as compared to tooling marks left by milling cutters and grinding wheels. The WEDM process leaves no residual burrs on the workpiece, which reduces or eliminates the need for subsequent finishing operations. From the literature several researchers have been applied the Taguchi method to optimize the process parameters in WEDM process. In the Present work Titanium diboride TiB 2 is considered for measuring the output parameters like material removal rate, surface roughness and overcut using Taguchi method. Electrical Discharge Machining (EDM) was first introduced in the 1940's as a crude device used to cut broken machining tools from expensive in-process parts. Since that time EDM has become a sophisticated and indispensable technology, revolutionizing the tool, die, and mold making industries, and making significant inroads into the production of highly accurate, intricate and difficult to machine production parts. In electrical discharge machining, it is important to select machining parameters for achieving optimal machining performance. Usually, the desired machining parameters are determined based on experience or handbook values. However, this does not ensure that the selected machining parameters result in optimal or near optimal machining performance for that particular electrical discharge machine and environment. The wire does not touch the work-piece, so there is no physical pressure imparted on the work- piece compared to grinding wheels and milling cutters. The Fig -1: Schematic Representation of WEDM 2. EXPERIMENTAL DESIGN Proper experimental design significantly contributes towards the accurate characterization and optimization of the process, in present work Taguchi L 27 orthogonal experiments is used to study the influence of process parameters on MRR, OC and SR. In this study process parameters selected are Pulse-on Time (TON), Pulse-off time (T OFF) and Wire feed rate (WF) whereas the Performance measures are: Material removal rate (MRR), Surface roughness (SR) and Overcut (OC).The work-piece selected for investigation of optimum setting for WEDM process is TiB 2. The chemical composition of TiB 2 is as shown in Table 1. Page 1657

2 Table -1: Chemical composition (in %) Ti B N Si Fe Ni Controlled process parameters such as Pulse on time (T ON), Pulse-off-time (T OFF) and Wire Feed (WF) used in this study are shown in Table 2. Each factor is investigated at different levels to determine the optimum settings for the WEDM process. These parameters and their levels were chosen based on the review of literature and the few preliminary investigations. The other process parameters may have effect on measure of performance. To avoid these, the other process parameters are kept constant; Servo voltage 50V, Servo feed 2100, Peak current 230A, Peak voltage 2, Water pressure 0lpm, Wire tension 8gm. The smallest standard 3-level Orthogonal Array L 27 is chosen. Table -2: Control factors and their levels Control factors Unit Level 1 Level 2 Level 3 Pulse-on time µs Pulse-off time µs Wire feed rate mm/min The parameters that were studied to determine the optimum setting for the WEDM process are as shown in Table 2. Table No. 3 shows the twenty seven cutting experimental runs with the assigned levels of the process parameters according to the selected L 27 orthogonal array. Table -3: S/N ratios of MRR, SR and OC Expt. S/N ratios for S/N ratios S/N ratios for No. MRR (gm/min) for SR (µm) OC (mm) Table -4: Response table for S/N ratio for MRR (Higher Level T ON T OFF W F Delta Fig -2: Main effect Plot of S/N ratios for Material Removal Rate Page 1658

3 In main effect plot of S/N ratio for material removal rate, x-axis indicates different levels of process parameters and Y-Axis shows average of S/N ratio. It can be observed from Graph no.1 that material removal rate increase with increase in pulse-on time and pulse of time. Wire feed rate have very small effect on material removal rate. Table No. 5: Response table for S/N ratio for SR (Lower Level T ON T OFF W F Delta Rank Fig -4: Main effect Plot of S/N ratios for overcut In main effect plot of S/N ratio for overcut, X axis indicates different levels of process parameters and Y axis shows average of S/N ratio. It can be observed from given Graph no.3 that overcut increases with increase in pulse-off time and also increases with increasing in pulse-on time and wire fed rate has very small effect on overcut. Table No. 7: Conformation of experiments for MRR Fig -3: Main effect Plot of S/N ratios for surface roughness In main effect plot S/N ratio for surface roughness, X-axes indicate different levels of process parameters and Y-axis shows average of S/N ratio. It can be observed from Graph no.2 that surface roughness decreases with decrease in pulse-on time. Pulse-off time and wire feed rate have very small effect on surface roughness. Table No. 6: Response table for S/N ratio for OC (Lower Level TON TOFF WF Delta Rank Level A3-B3-C3 S/N ratio MRR Table No. 8: Conformation of experiments for SR Level A1-B1-C2 S/N ratio SR Table No. 9: Conformation of experiments for OC Level A3-B3-C3 S/N ratio OC Comparison between actual experimented values and RSM prediction values. Result obtained from RSM method and experimented method should be validated. Results obtained from both experimented values and RSM prediction values are cross checked with each other. Finally residual error between then is found out. Page 1659

4 Table No. 10: Comparison between actual and RSM values for MRR, OC Performance Residual Actual Predicted Measures Error % Error MRR SR OC CONCLUSIONS The effect of pulse-on time, pulse-off time and wire feed are investigated in machining of TiB2 by keeping other process parameters constant. Use of the Taguchi method for the optimization of the wire-cut electric discharge machining process is demonstrated in this work. Based on the experimental results, the conclusions can be drawn as follows. 1. The Pulse-on time and pulse-off time are most significant whereas wire feed rate is insignificant for material removal rate. Response table for MRR indicate that pulse-on time has most effect on MRR followed by pulse-on time and wire feed rate. For maximum MRR, the recommended parametric combination is A3-B3-C3. 2. Response table for SR indicate that pulse-off time has most significant effect on SR follow by pulse-on time and wire feed rate. For better surface finish, the recommended parametric combination is A1-B1-C2. 3. Response table for OC indicate that pulse-off time has most effect on SR followed by pulse-on time and wire feed rate. For minimum OC, the recommended parametric combination is A3-B3-C3. The approach used in this study can be used for other material like steel and aluminium. The effect of thickness of material on output can be studied by using work piece material of different thickness. REFERENCES [1] Muthu Kumar. Suresh Babu, Venkatasamy and Raajenthiren, Optimization of the WEDM Parameters on Machining Incoloy -800 Super alloy with Multiple Quality Characteristics, International Journal of Engineering Science and Technology, Vol. 2(6), (2010) [2] Rina Chakravorty, Susanta Kumar Gauri, Shankar Chakraborty, A modified principal component analysis-based utility theory approach for optimization of correlated responses of EDM process, International Journal of Engineering, Science and Technology, Vol. 4, No. 2, (2012), pp [3] S. Sarkar, Mitra S, Bhattacharyya B Parametric optimization of wire electrical discharge machining of γ titanium aluminide alloy through an artificial neural network model, Int. Journal of Adv. Manufacturing Technolgy (2006) 27: [4] Saurav Datta, Siba Sankar Mahapatra, Modeling, simulation and parametric optimization of wire EDM process using response surface methodology coupled with grey-taguchi technique, International Journal of Engineering, Science and Technology, Vol. 2, No. 5, (2010), [5] Sorabh, Manoj Kumar, Ne raj Nirmal A Literature Review on Optimization of Machining Parameters in Wire EDM, International Journal of Latest Research in Science and Technology, Vol. 2, Issue 1, (2013), [6] Parveen Kumar, Bharat Bhushan & Dr. R.K. Gupta., A Literature Review on Optimization of Input Machining Parameters of Wire-EDM, International Journal of Research in Management, Economics and Commerce, Volume3, Issue 9, (2013), [7] Lokesh Goyat, Rajesh Dudi, Neeraj Sharma, WEDM Development and Optimization of Process: A Review, International Journal of Innovations in Engineering and Technology (IJIET), Vol. 2 Issue 3, (2013), [8] S. Mahendran, R. Devarajan, T. Nagarajan, and A. Majdi, Micro-EDM: Overview and Recent Developments, National Conference in Mechanical Engineering Research and Postgraduate Students, (2010), [9] G. M. Pradeep, Experimental Investigation and Analysis of Air with Water Mist Wire Cut Electrical Discharge Machining Process Using Rsm, Methodology, International Journal of Innovative Research in Science, Engineering and Technology Volume3, Special Issue 4, (2014), [10] Pujari Shinivasa Rao et al., Effect of WEDM conditions on surface roughness: A parametric Optimization using Taguchi method, IJAEST Vol. 6, Issue-1, (2011) [11] Pujari shrinivas Rao, Dr. Koona Ramji and Prof. Beela Satynarayana, Prediction of Material removal rate for Aluminum BIS Alloy in wire-cut EDM, IJEST Vol. 2 (12), (2010) [12] Shandilya et al. Optimization of SiCp/6061 Al(MMC) by WEDM process using surface methodology (2012) [13] S. Dhanabalan et al., Optimization of the electrical discharge machining process parameters with Multiple Performance Characteristics based for Titanium Grades, European Journal of Scientific Research, Vol. 68, (2012), [14] Atul Kumar and Dr. D. K. Singh, Strategic Optimization and Investigation Effect process parameters on Performance of WEDM, IJEST, Vol. 4, 2012, [15] S. B. Prajapati and N. S Patel Optimization of the process parameters on performance measures of wire EDM for AISI A2 tool steel,ijcer Vol. 3, Issue-4 (2013) [16] Ansish Kumar, Vinod Kumar, Jatinder Kumar, Experimental investigation on material transfer Page 1660

5 mechanism in WDEM process of pure titanium(grade2), Advances in Material Science and Engineering, Vol.-2013(2013), Article ID , 20 pages. [17] Kamal Jangra, Ajai Jain and Sandeep Grover, Optimization of performance characteristics in WEDM process using Taguchi method and gray relational analysis, Journal of Scientific & Industrial Research, Vol.-69, Aug. 2010, pp [18] S. Sivanaga et al., Parametric Evaluation for Machining Die-Steel with WEDM, International Journal of Scientific and Research Publications, Volume 3, Issue 4, April 2013 ISSN (2013). Page 1661

Optimization of WEDM Parameters for Super Ni-718 using Neutrosophic Sets and TOPSIS Method

Optimization of WEDM Parameters for Super Ni-718 using Neutrosophic Sets and TOPSIS Method Optimization of WEDM Parameters for Super Ni-718 using Neutrosophic Sets and TOPSIS Method Y Rameswara Reddy 1*, B Chandra Mohan Reddy 2 1,2 Department of Mechanical Engineering, Jawaharlal Nehru Technological

More information

Effect and Optimization of EDM Process Parameters on Surface Roughness for En41 Steel

Effect and Optimization of EDM Process Parameters on Surface Roughness for En41 Steel , pp. 33-358 http://dx.doi.org/10.157/ijhit.01.9.5.9 Effect and Optimization of EDM Process Parameters on Surface Roughness for En1 Steel Ch. Maheswara Rao 1 and K.Venkatasubbaiah 1 (Assistant Professor,

More information

Parameter Optimization of EDM on En36 Alloy Steel For MRR and EWR Using Taguchi Method

Parameter Optimization of EDM on En36 Alloy Steel For MRR and EWR Using Taguchi Method IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-184,p-ISSN: 2320-334X, Volume 13, Issue 3 Ver. VII (May- Jun. 201), PP 5-5 www.iosrjournals.org Parameter Optimization of EDM on

More information

Optimization of Machining Parameters in Wire Cut EDM of Stainless Steel 304 Using Taguchi Techniques

Optimization of Machining Parameters in Wire Cut EDM of Stainless Steel 304 Using Taguchi Techniques Advanced Materials Manufacturing & Characterization Vol. 8 Issue 1 (018) Advanced Materials Manufacturing & Characterization journal home page: www.ijammc-griet.com Optimization of Machining Parameters

More information

An investigation of material removal rate and kerf on WEDM through grey relational analysis

An investigation of material removal rate and kerf on WEDM through grey relational analysis Journal of Mechanical Engineering and Sciences ISSN (Print): 2289-4659; e-issn: 2231-8380 Volume 12, Issue 2, pp. 3633-3644, June 2018 Universiti Malaysia Pahang, Malaysia DOI: https://doi.org/10.15282/jmes.12.2.2018.10.0322

More information

Experimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process

Experimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process Experimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process Pravin D.Babar Mechanical Engineering Department, Rajarambapu Institute of Technology

More information

Modeling of Wire Electrical Discharge Machining of AISI D3 Steel using Response Surface Methodology

Modeling of Wire Electrical Discharge Machining of AISI D3 Steel using Response Surface Methodology 5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 214) December 12 th 14 th, 214, IIT Guwahati, Assam, India Modeling of Wire Electrical Discharge Machining

More information

Modeling and Optimization of WEDM Process Parameters on Machining of AISI D2 steel using Response Surface Methodology (RSM)

Modeling and Optimization of WEDM Process Parameters on Machining of AISI D2 steel using Response Surface Methodology (RSM) Modeling and Optimization of WEDM Process Parameters on Machining of AISI D2 steel using Response Surface Methodology (RSM) Sk. Mohammed Khaja 1, Ratan Kumar 2 Vikram Singh 3 1,2 CIPET- Hajipur, skmdkhaja@gmail.com

More information

OPTIMIZATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESSIN WED-MACHINING OF TiNi SMA USING GREY RELATION ANALYSIS

OPTIMIZATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESSIN WED-MACHINING OF TiNi SMA USING GREY RELATION ANALYSIS OPTIMIZATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESSIN WED-MACHINING OF TiNi SMA USING GREY RELATION ANALYSIS Manjaiah M 1*, Narendranath S 2, Basavarajappa S 3 1* Dept. of Mechanical Engineering,

More information

A Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach

A Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach A Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach Samar Singh, Lecturer, Dept of Mechanical Engineering, R.P. Indraprastha Institute of Technology (Karnal) MukeshVerma,

More information

Optimization of EDM process parameters using Response Surface Methodology for AISI D3 Steel

Optimization of EDM process parameters using Response Surface Methodology for AISI D3 Steel Optimization of EDM process parameters using Response Surface Methodology for AISI D3 Steel Mr.B.Gangadhar 1, Mr.N. Mahesh Kumar 2 1 Department of Mechanical Engineering, Sri Venkateswara College of Engineering

More information

Optimization of MRR and SR by employing Taguchis and ANOVA method in EDM

Optimization of MRR and SR by employing Taguchis and ANOVA method in EDM Optimization of and SR by employing Taguchis and ANOVA method in EDM Amardeep Kumar 1, Avnish Kumar Panigrahi 2 1M.Tech, Research Scholar, Department of Mechanical Engineering, G D Rungta College of Engineering

More information

Study of EDM Parameters on Mild Steel Using Brass Electrode

Study of EDM Parameters on Mild Steel Using Brass Electrode Study of EDM Parameters on Mild Steel Using Brass Electrode Amit Kumar #1, Abhishek Gaikwad *2, Amit Tiwari #3 # 1,3, Production Engineering (ME), SSET, Allahabad-211007, SHIATS, Allahabad, Uttar Pradesh

More information

International Journal of Scientific & Engineering Research, Volume 5, Issue 1, January ISSN

International Journal of Scientific & Engineering Research, Volume 5, Issue 1, January ISSN International Journal of Scientific & Engineering Research, Volume 5, Issue 1, January-2014 2026 Modelling of Process Parameters on D2 Steel using Wire Electrical Discharge Machining with combined approach

More information

RESPONSE SURFACE ANALYSIS OF EDMED SURFACES OF AISI D2 STEEL

RESPONSE SURFACE ANALYSIS OF EDMED SURFACES OF AISI D2 STEEL Advanced Materials Research Vols. 264-265 (2011) pp 1960-1965 Online available since 2011/Jun/30 at www.scientific.net (2011) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amr.264-265.1960

More information

Optimization Of Process Parameters In Drilling Using Taguchi Method

Optimization Of Process Parameters In Drilling Using Taguchi Method Optimization Of Process Parameters In Drilling Using Taguchi Method 1 P.Surendra, 2 B.Krishna Murthy, 3 M.V.Kiran Kumar 1 Associate Professor, 2 Assistant Professor, 3 Assistant Professor Department of

More information

Optimization of process parameter in electrochemical machining. Of Inconel 718 by Taguchi analysis

Optimization of process parameter in electrochemical machining. Of Inconel 718 by Taguchi analysis International Journal of Engineering Research and General Science Volume, Issue, January-February, 05 ISSN 09-70 Optimization of process parameter in electrochemical machining Of Inconel 78 by Taguchi

More information

Optimization of Wire EDM Process Parameters of Al 6061/Al 2 O 3 /3%red mud MMC

Optimization of Wire EDM Process Parameters of Al 6061/Al 2 O 3 /3%red mud MMC Optimization of Wire EDM Process Parameters of Al 6061/Al 2 O 3 /3%red mud MMC Dhinesh kumar.k #1 Sivakumar.M *2, Sivakumar.K *3,Kumar.M *4 # P.G scholar, Department of Mechanical Engineering,Bannari Amman

More information

Impact of Microchannel Geometrical Parameters in W-EDM Using RSM

Impact of Microchannel Geometrical Parameters in W-EDM Using RSM International Journal of Bioinformatics and Biomedical Engineering Vol. 1, No. 2, 2015, pp. 137-142 http://www.aiscience.org/journal/ijbbe Impact of Microchannel Geometrical Parameters in W-EDM Using RSM

More information

Optimization of Process Parameters in CNC Drilling of EN 36

Optimization of Process Parameters in CNC Drilling of EN 36 Optimization of Process Parameters in CNC ing of EN 36 Dr. K. Venkata Subbaiah 1, * Fiaz khan 2, Challa Suresh 3 1 Professor, Department of Mechanical Engineering, Andhra University, Visakhapatnam, Andhra

More information

Modeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V)

Modeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V) Modeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V) Basil Kuriachen 1, Dr. Josephkunju Paul 2, Dr.Jose Mathew 3 1 Research Scholar, Department of Mechanical Engineering,

More information

Experimental Investigation of CNC Turning Process Parameters on AISI 1018 carbon steel

Experimental Investigation of CNC Turning Process Parameters on AISI 1018 carbon steel Experimental Investigation of CNC Turning Process Parameters on AISI 1018 carbon steel Bijo Mathew 1,Edin Michael 2 and Jervin Das 3 1,2,3 Faculty, Department of Mechanical Engineering, Bishop Jerome institute,kollam,india

More information

Modelling And Optimization Of Electro Discharge Machining In C45 Material

Modelling And Optimization Of Electro Discharge Machining In C45 Material IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X PP. 25-32 www.iosrjournals.org Modelling And Optimization Of Electro Discharge Machining In C45 Material

More information

Optimization of Cutting Parameter of (SS302) on EDM using Taguchi Method Chintan A. Prajapati 1 Prof. Dr. Prashant Sharma 2 Prof.

Optimization of Cutting Parameter of (SS302) on EDM using Taguchi Method Chintan A. Prajapati 1 Prof. Dr. Prashant Sharma 2 Prof. IJSRD - International Journal for Scientific Research & Development Vol. 2, Issue 01, 14 ISSN (online): 2321-013 Optimization of tting Parameter of (SS302) on EDM using Taguchi Method Chintan A. Prajapati

More information

Optimization of Machining Parameters in ECM of Al/B4C Composites Using Taguchi Method

Optimization of Machining Parameters in ECM of Al/B4C Composites Using Taguchi Method International Journal of Applied Science and Engineering 2014. 12, 2: 87-97 Optimization of Machining Parameters in ECM of Al/B4C Composites Using Taguchi Method S. R. Rao a* and G. Padmanabhan b a Department

More information

Associate Professor, Department of Mechanical Engineering, Birla Institute of Technology, Mesra, Ranchi, India

Associate Professor, Department of Mechanical Engineering, Birla Institute of Technology, Mesra, Ranchi, India Optimization of machine process parameters on material removal rate in EDM for EN19 material using RSM Shashikant 1, Apurba Kumar Roy 2, Kaushik Kumar 2 1 Research Scholar, Department of Mechanical Engineering,

More information

Taguchi-grey relational based multi response optimization of electrical process parameters in electrical discharge machining

Taguchi-grey relational based multi response optimization of electrical process parameters in electrical discharge machining Indian Journal of Engineering & Materials Science Vol. 20, December 2013, pp. 471-475 Taguchi-grey relational based multi response optimization of electrical process parameters in electrical discharge

More information

Experimental study of electrical discharge drilling of stainless steel UNS S30400

Experimental study of electrical discharge drilling of stainless steel UNS S30400 IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Experimental study of electrical discharge drilling of stainless steel UNS S30400 To cite this article: E A H Hanash and M Y Ali

More information

Post Graduate Scholar, Department of Mechanical Engineering, Jalpaiguri Govt. Engineering College, India. 2

Post Graduate Scholar, Department of Mechanical Engineering, Jalpaiguri Govt. Engineering College, India. 2 International Journal of Technical Research and Applications e-issn: 30-8163, www.ijtra.com Volume 3, Issue 3 (May-June 015), PP. 5-60 INFLUENCE OF CONTROL PARAMETERS ON IN ELECTRICAL DISCHARGE MACHINING

More information

Investigation of effect of process parameters in micro hole drilling

Investigation of effect of process parameters in micro hole drilling Investigation of effect of process parameters in micro hole drilling Vaibhav Gosavi, Dr. Nitin Phafat, Dr. Sudhir Deshmukh 3 Research scholar,me MFG, JNEC Asso. Prof. Mech. Dept., JNEC 3 Principal, JNEC

More information

EXPERIMENTAL INVESTIGATION OF MRR, SURFACE ROUGHNESS AND OVERCUT OF AISI 304 STAINLESS STEEL IN EDM A THESIS SUBMITTED IN PARTIAL FULFILMENT

EXPERIMENTAL INVESTIGATION OF MRR, SURFACE ROUGHNESS AND OVERCUT OF AISI 304 STAINLESS STEEL IN EDM A THESIS SUBMITTED IN PARTIAL FULFILMENT EXPERIMENTAL INVESTIGATION OF MRR, SURFACE ROUGHNESS AND OVERCUT OF AISI 304 STAINLESS STEEL IN EDM A THESIS SUBMITTED IN PARTIAL FULFILMENT OF THE REQUIREMENTS FOR THE DEGREE OF Bachelor of Technology

More information

AnalysisoMRRandSRwithDifferentElectrodeforSS316onDi-SinkingEDMusingTaguchiTechnique

AnalysisoMRRandSRwithDifferentElectrodeforSS316onDi-SinkingEDMusingTaguchiTechnique Global Journal of Researches in Engineering Mechanical and Mechanics Engineering Volume 13 Issue 3 Version 1.0 Year 013 Type: Double Blind Peer Reviewed International Research Journal Publisher: Global

More information

Statistical and regression analysis of Material Removal Rate for wire cut Electro Discharge Machining of SS 304L using design of experiments

Statistical and regression analysis of Material Removal Rate for wire cut Electro Discharge Machining of SS 304L using design of experiments Vol. 2(5), 200, 02028 Statistical and regression analysis of Material Removal Rate for wire cut Electro Discharge Machining of SS 304L using design of experiments Vishal Parashar a*, A.Rehman b, J.L.Bhagoria

More information

Performance Evolution and Selection of Controllable Process variables in ECM for Al, B4C Metal Matrix Composites

Performance Evolution and Selection of Controllable Process variables in ECM for Al, B4C Metal Matrix Composites International Journal of Management, IT & Engineering Vol. 8 Issue 12, December 2018, ISSN: 2249-0558 Impact Factor: 7.119 Journal Homepage: Double-Blind Peer Reviewed Refereed Open Access International

More information

Study of water assisted dry wire-cut electrical discharge machining

Study of water assisted dry wire-cut electrical discharge machining Indian Journal of Engineering & Materials Sciences Vol. 1, February 014, pp. 75-8 Study of water assisted dry wire-cut electrical discharge machining S Boopathi* & K Sivakumar Department of Mechanical

More information

OPTIMIZATION OF PROCESS PARAMETERS IN ELECTROCHEMICAL DEBURRING OF DIE STEEL USING TAGUCHI METHOD

OPTIMIZATION OF PROCESS PARAMETERS IN ELECTROCHEMICAL DEBURRING OF DIE STEEL USING TAGUCHI METHOD International Journal of Modern Manufacturing Technologies ISSN 2067 3604, Vol. IV, No. 1 / 2012 121 OPTIMIZATION OF PROCESS PARAMETERS IN ELECTROCHEMICAL DEBURRING OF DIE STEEL USING TAGUCHI METHOD Manoj

More information

Puttur, Andhra Pradesh, India , Andhra Pradesh, India ,

Puttur, Andhra Pradesh, India , Andhra Pradesh, India , th International & th All India Manufacturing Technology, Design and Research Conference (AIMTDR ) December th th,, IIT Guwahati, Assam, India OPTIMIZATI OF DIMENSIAL DEVIATI:WIRE CUT EDM OF VANADIS- E

More information

EXPERIMENTAL INVESTIGATION OF MRR AND SURFACE ROUGHNESS OF EN-18 STEEL IN ECM

EXPERIMENTAL INVESTIGATION OF MRR AND SURFACE ROUGHNESS OF EN-18 STEEL IN ECM EXPERIMENTAL INVESTIGATION OF MRR AND SURFACE ROUGHNESS OF EN-18 STEEL IN ECM BY K SAYAN KUMAR (109ME0595) Under The Guidance of Prof. C.K.Biswas Department of Mechanical Engineering National Institute

More information

International Journal of Scientific & Engineering Research, Volume 5, Issue 12, December ISSN IJSER

International Journal of Scientific & Engineering Research, Volume 5, Issue 12, December ISSN IJSER International Journal of Scientific & Engineering Research, Volume 5, Issue 12, December-2014 29 Prediction of EDM process parameters by using Artificial Neural Network (ANN) - A Prediction Technique Mitali

More information

Optimization of Radial Force in Turning Process Using Taguchi s Approach

Optimization of Radial Force in Turning Process Using Taguchi s Approach 5 th International & 6 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 04) December th 4 th, 04, IIT Optimization of Radial Force in Turning Process Using Taguchi s Approach

More information

Multi-Objective Optimization of Electrochemical machining of EN31 steel by Grey Relational Analysis

Multi-Objective Optimization of Electrochemical machining of EN31 steel by Grey Relational Analysis International Journal of Modeling and Optimization, Vol. 1, No., June 011 Multi-Objective Optimization of Electrochemical machining of EN1 steel by Grey Relational Analysis D. Chakradhar, A. Venu Gopal

More information

Prediction of performance parameters in Wire EDM of HcHcr steel using Artificial Neural Network

Prediction of performance parameters in Wire EDM of HcHcr steel using Artificial Neural Network Prediction of performance parameters in Wire EDM of HcHcr steel using Artificial Neural Network N. G. Parmar Mechanical Engineering Department Government Polytechnic, Kheda Gujarat, India e-mail: ng_parmar@yahoo.co.in

More information

Experimental Investigation of Machining Parameter in Electrochemical Machining

Experimental Investigation of Machining Parameter in Electrochemical Machining Experimental Investigation of Machining Parameter in Electrochemical Machining Deepanshu Shrivastava 1, Abhinav Sharma 2, Harsh Pandey 2 1 M.TECH Sholar, DR.C.V. RAMAN UNIVERSITY, KOTA C.G.,INDIA 2 M.TECH

More information

Decision Science Letters

Decision Science Letters Decision Science Letters 4 (2015) 211 226 Contents lists available at GrowingScience Decision Science Letters homepage: www.growingscience.com/dsl Parameter selection in non-traditional machining processes

More information

Application of Fuzzy Logic and TOPSIS in the Taguchi Method for Multi-Response Optimization in Electrical Discharge Machining (EDM)

Application of Fuzzy Logic and TOPSIS in the Taguchi Method for Multi-Response Optimization in Electrical Discharge Machining (EDM) Application of Fuzzy Logic and TOPSIS in the Taguchi Method for Multi-Response Optimization in Electrical Discharge Machining (EDM) Thesis submitted in partial fulfillment of the requirements for the Degree

More information

MODELING OF SURFACE ROUGHNESS IN WIRE ELECTRICAL DISCHARGE MACHINING USING ARTIFICIAL NEURAL NETWORKS

MODELING OF SURFACE ROUGHNESS IN WIRE ELECTRICAL DISCHARGE MACHINING USING ARTIFICIAL NEURAL NETWORKS Int. J. Mech. Eng. & Rob. Res. 013 P Vijaya Bhaskara Reddy et al., 013 Research Paper ISSN 78 0149 www.ijmerr.com Vol., No. 1, January 013 013 IJMERR. All Rights Reserved MODELING OF SURFACE ROUGHNESS

More information

EXPERIMENTAL INVESTIGATIONS ON ORBITAL ELECTRO DISCHARGE MACHINING OF INCONEL 718 USING TAGUCHI TECHNIQUE

EXPERIMENTAL INVESTIGATIONS ON ORBITAL ELECTRO DISCHARGE MACHINING OF INCONEL 718 USING TAGUCHI TECHNIQUE International Journal of Modern Manufacturing Technologies ISSN 2067 3604, Vol. IV, No. 1 / 2012 53 EXPERIMENTAL INVESTIGATIONS ON ORBITAL ELECTRO DISCHARGE MACHINING OF INCONEL 718 USING TAGUCHI TECHNIQUE

More information

APPLICATION OF GREY RELATIONAL ANALYSIS TO MACHINING PARAMETERS DETERMINATION OF WIRE ELECTRICAL DISCHARGE MACHINING

APPLICATION OF GREY RELATIONAL ANALYSIS TO MACHINING PARAMETERS DETERMINATION OF WIRE ELECTRICAL DISCHARGE MACHINING APPLICATION OF GREY RELATIONAL ANALYSIS TO MACHINING PARAMETERS DETERMINATION OF WIRE ELECTRICAL DISCHARGE MACHINING J.T. Huang 1 and Y.S. Liao 1 Department of Automatic Engineering, Kaoyuan Institute

More information

Modeling and Optimization of Milling Process by using RSM and ANN Methods

Modeling and Optimization of Milling Process by using RSM and ANN Methods Modeling and Optimization of Milling Process by using RSM and ANN Methods M.R. SOLEYMANI YAZDI, A. KHORRAM Abstract Nowadays numerical and Artificial Neural Networks (ANN) methods are widely used for both

More information

FEM ANALYSIS WITH EXPERIMENTAL RESULTS TO STUDY EFFECT OF EDM PARAMETERS ON MRR OF AISI 1040 STEEL

FEM ANALYSIS WITH EXPERIMENTAL RESULTS TO STUDY EFFECT OF EDM PARAMETERS ON MRR OF AISI 1040 STEEL FEM ANALYSIS WITH EXPERIMENTAL RESULTS TO STUDY EFFECT OF EDM PARAMETERS ON MRR OF AISI 1040 STEEL Imran Patel 1 & Prashant Powar 2 1PG Student, Department of Production Engineering, KIT s College of Engineering,

More information

MATHEMATICAL MODELING OF MATERIAL REMOVAL RATE OF T90Mn2W50Cr45 TOOL STEEL IN WIRE ELECTRICAL DISCHARGE MACHINE

MATHEMATICAL MODELING OF MATERIAL REMOVAL RATE OF T90Mn2W50Cr45 TOOL STEEL IN WIRE ELECTRICAL DISCHARGE MACHINE International Journal of Mechanical and Materials Engineering (IJMME), Vol. 7 (01), No. 3, 03-08. MATHEMATICAL MODELING OF MATERIAL REMOVAL RATE OF T90MnW50Cr45 TOOL STEEL IN WIRE ELECTRICAL DISCHARGE

More information

Analysis and Mathematical Modeling of Wire EDM Process Parameters for Commercial Graphite by Using Response Surface Methodology

Analysis and Mathematical Modeling of Wire EDM Process Parameters for Commercial Graphite by Using Response Surface Methodology Advance Research and Innovations in Mechanical, Material Science, Industrial Engineering and Management - ICARMMIEM-201 7 Analysis and Mathematical Modeling of Wire EDM Process Parameters for Commercial

More information

Optimization of delamination factor in drilling of carbon fiber filled compression molded GFRP composite

Optimization of delamination factor in drilling of carbon fiber filled compression molded GFRP composite Optimization of delamination in drilling of carbon fiber filled compression molded GFRP composite Anurag Gupta 1 Ajay Singh Verma Sandeep Chhabra Ranjeet Kumar Assistant professor, Department of Mechanical

More information

Influence of Input Parameters on Characteristics of Electro Chemical Machining Process

Influence of Input Parameters on Characteristics of Electro Chemical Machining Process International Journal of Applied Science and Engineering 23., : 3-24 Influence of Input Parameters on Characteristics of Electro Chemical Machining Process C. Senthilkumara,*, G. Ganesana, and R. Karthikeyanb

More information

Algorithm for Modeling Wire Cut Electrical Discharge Machine Parameters using Artificial Neural Network

Algorithm for Modeling Wire Cut Electrical Discharge Machine Parameters using Artificial Neural Network Algorithm for Modeling Wire Cut Electrical Discharge Machine Parameters using Artificial Neural Network G.Sankara Narayanan #1, D.Vasudevan #2 # Department of Mechanical Engineering, #1 SBM College of

More information

Parameters Optimization of Rotary Ultrasonic Machining of Glass Lens for Surface Roughness Using Statistical Taguchi s Experimental Design

Parameters Optimization of Rotary Ultrasonic Machining of Glass Lens for Surface Roughness Using Statistical Taguchi s Experimental Design Parameters Optimization of Rotary Ultrasonic Machining of Glass Lens for Surface Roughness Using Statistical Taguchi s Experimental Design MUHAMMAD HISYAM LEE Universiti Teknologi Malaysia Department of

More information

Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses

Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses int. j. prod. res., 2003, vol. 41, no. 8, 1707 1720 Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses J. T. HUANG{* and Y. S. LIAO{ Grey relational analyses

More information

ADVANCES in NATURAL and APPLIED SCIENCES

ADVANCES in NATURAL and APPLIED SCIENCES ADVANCES in NATURAL and APPLIED SCIENCES ISSN: 1995-0772 Published BYAENSI Publication EISSN: 1998-1090 http://www.aensiweb.com/anas 2017 April 11(4): pages 260-269 Open Access Journal A Study On Wet And

More information

2. To compare results with a previous published work[6].

2. To compare results with a previous published work[6]. Predicting Material Removal Rate of EDM of 95WC/5NI Composites Fuzzy Logic Omar M Elmabrouk Industrial and Manufacturing Systems Engineering Department Benghazi University Benghazi, Libya omarelmabrouk@uobeduly

More information

DEVELOPMENT OF AN ELECTRO CHEMICAL MACHINE SET-UP AND EXPERIMENTATIONS

DEVELOPMENT OF AN ELECTRO CHEMICAL MACHINE SET-UP AND EXPERIMENTATIONS DEVELOPMENT OF AN ELECTRO CHEMICAL MACHINE SET-UP AND EXPERIMENTATIONS Aniket Jadhav 1, Kishor D. Patil, D. B. Jadhav 3, W. G. Kharche 4 1 M.Tech.Student, Mechanical Engineering Department, B.V.D.U.C.O.E.

More information

ELECTRIC DISCHARGE MACHINING AND MATHEMATICAL MODELING OF Al-ALLOY-20 % SiC p COMPOSITES USING COPPER ELECTRODE

ELECTRIC DISCHARGE MACHINING AND MATHEMATICAL MODELING OF Al-ALLOY-20 % SiC p COMPOSITES USING COPPER ELECTRODE International Journal of Mechanical and Production Engineering Research and Development (IJMPERD ) ISSN 2249-6890 Vol.2, Issue 2 June 2012 37-46 TJPRC Pvt. Ltd., ELECTRIC DISCHARGE MACHINING AND MATHEMATICAL

More information

Numerical Modeling and Multi-Objective Optimization of Micro-Wire EDM Process

Numerical Modeling and Multi-Objective Optimization of Micro-Wire EDM Process 5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 2014) December 12 th 14 th, 2014, IIT Guwahati, Assam, India Numerical Modeling and Multi-Objective

More information

Experimental Study of Effect of Parameter variations on output parameters for Electrochemical Machining of SS AISI 202

Experimental Study of Effect of Parameter variations on output parameters for Electrochemical Machining of SS AISI 202 IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684 Volume 5, Issue 5 (Mar. - Apr. 2013), PP 65-71 Experimental Study of Effect of Parameter variations on output parameters for

More information

Optimization of Machining Process Parameters in Drilling of

Optimization of Machining Process Parameters in Drilling of Optimization of Machining Process Parameters in Drilling of CFRP Using Multi-Objective Taguchi Technique, TOPSIS and RSA Optimization of Machining Process Parameters in Drilling of CFRP Using Multi-Objective

More information

S. S.Mahapatra National Institute of Technology Department of Mechanical Engineering Rourkela. INDIA. Amar Patnaik.

S. S.Mahapatra National Institute of Technology Department of Mechanical Engineering Rourkela. INDIA. Amar Patnaik. S. S.Mahapatra and Amar Patnaik S. S.Mahapatra ssm@nitrkl.ac.in National Institute of Technology Department of Mechanical Engineering Rourkela. INDIA Amar Patnaik amar_mech@sify.com G.I.E.T Department

More information

Determining Machining Parameters of Corn Byproduct Filled Plastics

Determining Machining Parameters of Corn Byproduct Filled Plastics Iowa State University From the SelectedWorks of Kurt A. Rosentrater 8 Determining Machining Parameters of Corn Byproduct Filled Plastics Kurt A. Rosentrater, United States Department of Agriculture Andrew

More information

Journal of Chemical and Pharmaceutical Research, 2017, 9(10): Research Article

Journal of Chemical and Pharmaceutical Research, 2017, 9(10): Research Article Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research, 2017, 9(10):59-69 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 Experimental Investigation of Surface Roughness of

More information

THere is a heavy demand of the advanced materials with

THere is a heavy demand of the advanced materials with Vol:3, No:9, 29 Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel M. K. Pradhan*, and C. K. Biswas, International Science Index, Mechanical

More information

Experimental Investigation of Micro-EDM Process on Brass using Taguchi Technique

Experimental Investigation of Micro-EDM Process on Brass using Taguchi Technique Experimental Investigation of Micro-EDM Process on Brass using Taguchi Technique Ananya Upadhyay ananya.upadhyay@gmail.com Vijay Pandey Vinay Sharma Ved Prakash CSIR- Central Mechanical Engineering Research

More information

Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel

Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel Neuro-fuzzy model and Regression model a comparison study of MRR in Electrical discharge machining of D2 tool steel M. K. Pradhan*, and C. K. Biswas, Abstract In the current research, neuro-fuzzy model

More information

Influence of Electrode Material and Process Parameters on Surface Quality and MRR in EDM of AISI H13 using ANN

Influence of Electrode Material and Process Parameters on Surface Quality and MRR in EDM of AISI H13 using ANN Influence of Electrode Material and Process Parameters on Surface Quality and MRR in EDM of AISI H13 using ANN Bhavesh A. Patel 1, D. S. Patel 2, Haresh A. Patel 3 1 (Assistant Professor, Department of

More information

OPTIMIZATION OF PROCESS PARAMETERS IN DIRECT METAL DEPOSITION TECHNIQUE USING TAGUCHI METHOD

OPTIMIZATION OF PROCESS PARAMETERS IN DIRECT METAL DEPOSITION TECHNIQUE USING TAGUCHI METHOD International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 3, May June 2016, pp.225 239, Article ID: IJMET_07_03_022 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=3

More information

MULTI-RESPONSE OPTIMIZATION OF EDM PERFORMANCE CHARACTERISTICS USING RESPONSE SURFACE METHODOLOGY AND DESIRABILITY FUNCTION

MULTI-RESPONSE OPTIMIZATION OF EDM PERFORMANCE CHARACTERISTICS USING RESPONSE SURFACE METHODOLOGY AND DESIRABILITY FUNCTION VOL. 9, NO. 1, DECEMBER 014 ISSN 1819-6608 006-014 Asian Research Publishing Network (ARPN). All rights reserved. MULTI-RESPONSE OPTIMIZATION OF EDM PERFORMANCE CHARACTERISTICS USING RESPONSE SURFACE METHODOLOGY

More information

Material removal characteristics of microslot (kerf) geometry

Material removal characteristics of microslot (kerf) geometry DOI 10.1007/s00170-010-2645-z ORIGINAL ARTICLE Material removal characteristics of microslot (kerf) geometry in μ-wedm on aluminum Kodalagara Puttanarasaiah Somashekhar & Nottath Ramachandran & Jose Mathew

More information

Mr. Harshit K. Dave 1, Dr. Keyur P. Desai 2, Dr. Harit K. Raval 3

Mr. Harshit K. Dave 1, Dr. Keyur P. Desai 2, Dr. Harit K. Raval 3 Investigations on Prediction of MRR and Surface Roughness on Electro Discharge Machine Using Regression Analysis and Artificial Neural Network Programming Mr. Harshit K. Dave 1, Dr. Keyur P. Desai 2, Dr.

More information

A Comparative Modeling and Multi- Objective Optimization in Wire EDM Process on H21 Tool Steel Using Intelligent Hybrid Approach

A Comparative Modeling and Multi- Objective Optimization in Wire EDM Process on H21 Tool Steel Using Intelligent Hybrid Approach A Comparative Modeling and Multi- Objective Optimization in Wire EDM Process on H21 Tool Steel Using Intelligent Hybrid Approach Bikash Choudhuri *, Ruma Sen, Subrata Kumar Ghosh, S. C. Saha Mechanical

More information

MULTI-RESPONSE ANALYSIS OF ELECTRO-CHEMICAL MACHINING PROCESS USING PRINCIPAL COMPONENT ANALYSIS

MULTI-RESPONSE ANALYSIS OF ELECTRO-CHEMICAL MACHINING PROCESS USING PRINCIPAL COMPONENT ANALYSIS MULTI-RESPONSE ANALYSIS OF ELECTRO-CHEMICAL MACHINING PROCESS USING PRINCIPAL COMPONENT ANALYSIS K P Maity*, N K Verma Department of Mechanical Engineering National Institute of Technology, Rourkela-798

More information

A Review Paper on Rotary Electro-Discharge Machining

A Review Paper on Rotary Electro-Discharge Machining A Review Paper on Rotary Electro-Discharge Machining 1 Mr. Ganesh Pandurang Jadhav, 2 Dr. Narendra Narve 1 P.G.Student, 2 Professor Department Of Mechanical Engineering, JSPM Bhagwant Institute of Technology,

More information

Study on Erosion Mechanism of Magnetic-field-assisted Micro-EDM

Study on Erosion Mechanism of Magnetic-field-assisted Micro-EDM Study on Erosion Mechanism of Magnetic-field-assisted Micro-EDM Xuyang Chu a, Kai Zhu b, Yiru Zhang c and Chunmei Wang d Department of mechanical and electrical engineering, Xiamen University, Xiamen 361005,

More information

Optimizing Feed and Radial Forces on Conventional Lathe Machine of En31b Alloy Steel through Taguchi s Parameter Design Approach

Optimizing Feed and Radial Forces on Conventional Lathe Machine of En31b Alloy Steel through Taguchi s Parameter Design Approach RESEARCH ARTICLE OPEN ACCESS Optimizing Feed and Radial Forces on Conventional Lathe Machine of En31b Alloy Steel through Taguchi s Parameter Design Approach Mohd. Rafeeq 1, Mudasir M Kirmani 2 1 Assistant

More information

OPTIMIZATION OF PROCESS PARAMETERS FOR MACHINING OF MILD STEEL EN18 BY RESPONSE SURFACE METHODOLOGY

OPTIMIZATION OF PROCESS PARAMETERS FOR MACHINING OF MILD STEEL EN18 BY RESPONSE SURFACE METHODOLOGY OPTIMIZATION OF PROCESS PARAMETERS FOR MACHINING OF MILD STEEL EN18 BY RESPONSE SURFACE METHODOLOGY Puneet Kumar 1*, Ashwani Kumar Dhingra 2 and Pankaj Kumar 3 1, 2 Department of Mechanical Engineering,

More information

EXPERIMENTAL ANALYSIS ON DE-LAMINATION IN DRILLING GFRP COMPOSITE MATERIAL

EXPERIMENTAL ANALYSIS ON DE-LAMINATION IN DRILLING GFRP COMPOSITE MATERIAL EXPERIMENTAL ANALYSIS ON DE-LAMINATION IN DRILLING GFRP COMPOSITE MATERIAL N.Parkunam 1, G.Gopi 2, Dr.D.Threshkumar 3 1 PG Scholar, PTR College of Engineering and Technology, Madurai, Tamilnadu, (India)

More information

Application of a Multi-Criteria-Decision-Making (MCDM) Method of TOPSIS in Drilling of AA6082

Application of a Multi-Criteria-Decision-Making (MCDM) Method of TOPSIS in Drilling of AA6082 Application of a Multi-Criteria-Decision-Making (MCDM) Method of TOPSIS in Drilling of AA6082 Abstract Penuganti Padma *, M. Chaitanya Mayee * M. Tech, Department of Mechanical Engineering, S.V.P. Engineering

More information

International Journal of ChemTech Research CODEN (USA): IJCRGG ISSN: Vol.7, No.6, pp ,

International Journal of ChemTech Research CODEN (USA): IJCRGG ISSN: Vol.7, No.6, pp , International Journal of ChemTech Research CODEN (USA): IJCRGG ISSN: 0974-4290 Vol.7, No.6, pp 2625-2631, 2014-2015 Response Surface Methodology and Desirability Analysis for OptimizingμWEDMParameters

More information

Application of Taguchi method in optimization of control parameters of grinding process for cycle time reduction Snehil A. Umredkar 1, Yash Parikh 2

Application of Taguchi method in optimization of control parameters of grinding process for cycle time reduction Snehil A. Umredkar 1, Yash Parikh 2 Application of Taguchi method in optimization of control parameters of grinding process for cycle time reduction Snehil A. Umredkar, Yash Parikh 2 (Department of Mechanical Engineering, Symbiosis Institute

More information

Drilling Mathematical Models Using the Response Surface Methodology

Drilling Mathematical Models Using the Response Surface Methodology International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS Vol:5 No:06 9 Drilling Mathematical Models Using the Response Surface Methodology Panagiotis Kyratsis, Nikolaos Taousanidis, Apostolos

More information

PARAMETRIC OPTIMIZATION OF EDM USING MULTI-RESPONSE SIGNAL-TO- NOISE RATIO TECHNIQUE

PARAMETRIC OPTIMIZATION OF EDM USING MULTI-RESPONSE SIGNAL-TO- NOISE RATIO TECHNIQUE JPE (2016) Vol.19 (2) Payal, H., Maheshwari, S., Bharti, S.P. Original Scientific Paper PARAMETRIC OPTIMIZATION OF EDM USING MULTI-RESPONSE SIGNAL-TO- NOISE RATIO TECHNIQUE Received: 31 October 2016 /

More information

OPTIMIZATION ON SURFACE ROUGHNESS OF BORING PROCESS BY VARYING DAMPER POSITION

OPTIMIZATION ON SURFACE ROUGHNESS OF BORING PROCESS BY VARYING DAMPER POSITION OPTIMIZATION ON SURFACE ROUGHNESS OF BORING PROCESS BY VARYING DAMPER POSITION Wasis Nugroho, Nor Bahiyah Baba and Adi Saptari Faculty of Manufacturing Engineering Technology, TATI University College,

More information

Determination of Machining Parameters of Corn Byproduct Filled Plastics

Determination of Machining Parameters of Corn Byproduct Filled Plastics Paper 99, IT 3 Determination of Machining Parameters of Corn Byproduct Filled Plastics Kurt A. osentrater, Ph.D. Lead Scientist, Agricultural and Bioprocess Engineer, USDA, Agricultural esearch Service,

More information

CHAPTER -6 ANALYSIS AND DISCUSSION OF RESULTS

CHAPTER -6 ANALYSIS AND DISCUSSION OF RESULTS CHAPTER -6 ANALYSIS AND DISCUSSION OF RESULTS This chapter presents the analysis and discussion of the results obtained from the experimental work conducted in Chapter-5. The effect of cryogenic treated

More information

A study to achieve a fine surface finish in Wire-EDM

A study to achieve a fine surface finish in Wire-EDM Journal of Materials Processing Technology 149 (24) 165 171 A study to achieve a fine surface finish in Wire-EDM Y.S. Liao a,, J.T. Huang b, Y.H. Chen a a Department of Mechanical Engineering, National

More information

Prediction and analysis of radial overcut in holes drilled by electrochemical machining process

Prediction and analysis of radial overcut in holes drilled by electrochemical machining process Cent. Eur. J. Eng. 3(3) 2013 466-474 DOI: 10.2478/s13531-011-0074-x Central European Journal of Engineering Prediction and analysis of radial overcut in holes drilled by electrochemical machining process

More information

Experimental Data Mining Techniques (Using Multiple Statistical Methods)

Experimental Data Mining Techniques (Using Multiple Statistical Methods) www.ijcsi.org 132 Experimental Data Mining Techniques (Using Multiple Statistical Methods) Mustafa Zaidi 1, Bushra A. Saeed 2, I. Amin 3 and Nukman Yusoff 4 1 Department of Computer Science, SZABIST Karachi,

More information

A CASE STUDY ON APPLICATION OF FUZZY LOGIC IN ELECTRICAL DISCHARGE MACHINING (EDM)

A CASE STUDY ON APPLICATION OF FUZZY LOGIC IN ELECTRICAL DISCHARGE MACHINING (EDM) A CASE STUDY ON APPLICATION OF FUZZY LOGIC IN ELECTRICAL DISCHARGE MACHINING (EDM) Thesis submitted in partial fulfillment of the requirements for the Degree of Bachelor of Technology (B. Tech.) In Mechanical

More information

OPTIMIZATION OF MACHINING PARAMETERS USING DESIRABILITY FUNCTION ANALYSIS AND ANOVA FOR THERMO-MECHANICAL FORM DRILLING

OPTIMIZATION OF MACHINING PARAMETERS USING DESIRABILITY FUNCTION ANALYSIS AND ANOVA FOR THERMO-MECHANICAL FORM DRILLING International Journal of Industrial Engineering & Technology (IJIET) ISSN(P): 2277-4769; ISSN(E): 2278-9456 Vol. 4, Issue 1, Feb 2014, 19-26 TJPRC Pvt. Ltd. OPTIMIZATION OF MACHINING PARAMETERS USING DESIRABILITY

More information

Study of the effect of machining parameters on material removal rate and electrode wear during Electric Discharge Machining of mild steel

Study of the effect of machining parameters on material removal rate and electrode wear during Electric Discharge Machining of mild steel Journal of Engineering Science and Technology Review 5 (1) (2012) 14-18 Research Article JOURNAL OF Engineering Science and Technology Review www.jestr.org Study of the effect of machining parameters on

More information

Artificial Neural Network Modelling for Wire-EDM Processing of Aluminium Silicon Carbide Metal Matrix Composite

Artificial Neural Network Modelling for Wire-EDM Processing of Aluminium Silicon Carbide Metal Matrix Composite Artificial Neural Network Modelling for Wire-EDM Processing of Aluminium Silicon Carbide Metal Matrix Composite R. A. Kapgate, V. H. Tatwawadi Abstract The complex phenomenon of wire electrical discharge

More information

Performance analysis of µed-milling process using various statistical techniques

Performance analysis of µed-milling process using various statistical techniques Int. J. Machining and Machinability of Materials, Vol. 11, No. 2, 2012 183 Performance analysis of µed-milling process using various statistical techniques G. Karthikeyan Department of Mechanical Engineering,

More information

A STUDY OF THE ACCURACY OF THE MICRO ELECTRICAL DISCHARGE MACHINING DRILLING PROCESS

A STUDY OF THE ACCURACY OF THE MICRO ELECTRICAL DISCHARGE MACHINING DRILLING PROCESS A STUDY OF TE ACCURACY OF TE MICRO ELECTRICAL DISCARGE MACINING DRILLING PROCESS D.T. Pham, S.S. Dimov, S. Bigot, A. Ivanov, and K. Popov Manufacturing Engineering Centre, School of Engineering, Cardiff

More information