Flow Generated by Fractal Impeller in Stirred Tank: CFD Simulations
|
|
- Leona Lamb
- 5 years ago
- Views:
Transcription
1 Flow Generated by Fractal Impeller in Stirred Tank: CFD Simulations Gunwant M. Mule and Amol A. Kulkarni* Chem. Eng. & Proc. Dev. Division, CSIR-National Chemical Laboratory, Pune , INDIA *Corresponding author Phone: , Fax: ,
2 Abstract: Stirred tank has been the research area for many decades due to its applicability in chemical, pharmaceuticals, polymers, food and paints industries for variety of operation. Most of the energy supplied by the impeller is dissipated in the impeller region which leads to nonuniformities in the energy dissipation throughout the reactor. In order to reduce the extent of non-uniformities we propose the use of Fractal Impeller (FI) for mixing and dispersion. Here we present the flow patterns generated by fractal impeller using CFD simulation (k-ε model). Mean velocities have been compared with the experimental data and show good agreement. But turbulent kinetic energy is under-predicted or over-predicted in some part of the vessel.
3 Introduction: Mixing using impeller in stirred tank is often used in the chemical and its allied industries. Design of impellers and stirred tank geometry is the key thing for mixing operations. Usually in the industries stirred tank reactors operate at the turbulent regime (expect for viscous fluid) and the most active zone of the stirred tank is considered to be the impeller region[1]. Uniformity in energy dissipation in the stirred tank with conventional impeller is hard to achieve. Wu and Patterson[2] studied the energy dissipation for Rushton turbine; authors concluded that about 30% of the total energy was dissipated in the impeller region, 30% in the impeller discharge region and rest in the bulk of the tank. Similarly, Zhou and Kresta[3] studied the maximum energy dissipation in the stirred tank for various geometry and impellers. They found the bulk of the energy dissipated in the impeller region and the impeller discharged stream. In order to reduce the non-uniformity and to make the entire reactor hydrodynamically active in a similar manner, here we propose the use of Fractal Impeller (FI) for mixing and dispersion. Fractal impeller occupies less than 0.4% of the total volume of the reactor which is nearly equal to the conventional impellers. The impeller does not have any blades that sweep the liquid with it but the arrangement of blades only allows to cut the fluid thereby lowering the friction throughout the tank. Performance of the present impeller design in terms of power consumption, mixing time, solid-liquid suspension and gas-liquid dispersion has been studied[4]. The power number (N P ) was found 0.38 which is lower than the conventional impellers (Ruston turbine = 6, PBTD = 1.84). Mixing performance was also relatively better than the conventional impellers. Bubble size distribution in gas-liquid dispersion was very much narrow which helps proving the self similarity hypothesis. Computational Modelling: In CFD model, three dimensional time averaged Reynolds transport equations were solved with the k-ε model for turbulence. The equations were solved using rotating frame of reference formulations. The transport equation for a generalized flow variable φ are written as = + (1) Here φ stands for u j, k, ε etc. The source terms for different flow variables (S Q ) are different.
4 Fig. 1 shows the computational domain of the stirred tank with Fractal Impeller (FI) along with the grid statistics. Post processing of the data has been done using MATLAB. Figure 1: Computational domain and grid statistics of stirred tank with fractal impeller Result and discussion: The design of the fractal impeller is such that it does not have fluid sweeping blades, therefore; large eddies induced due to fluid sweeping is avoided. Moreover, shear zones observed in the stirred tank with conventional impeller are also eliminated. The main branches of the fractal impeller induce radial discharge stream towards the wall of the tank. Near tank wall, the radial discharge divides into opposite streams forming several circulation loops. Moreover, the flow generated by the fractal impeller is largely a tangential flow as all blades simply cut the fluid in different planes. Thus, it helps the interaction of different mixing zones. In such situations, interaction of eddies in different zones helps obtain uniform mixing even at relatively low RPM especially in gas-liquid dispersion.
5 a) b) Figure 2: Flow pattern generated by Fractal Impeller a) CFD at 50 RPM b) UVP at 100 RPM Conclusion: Flow pattern generated by Fractal Impeller in a stirred tank has been studied using CFD simulations. Flow generated by Fractal Impeller was observed to have strong tangential flow and small circulating eddies. The interaction of eddies help obtain uniform mixing even at small RPM. References: 1. Alopaeus, V., P. Moilanen, and M. Laakkonen, Analysis of stirred tanks with twoâ zone models. Aiche Journal, (10): p Wu, H. and G.K. Patterson, Laser-Doppler measurements of turbulent-flow parameters in a stirred mixer. Chemical Engineering Science, (10): p Zhou, G. and S.M. Kresta, Impact of tank geometry on the maximum turbulence energy dissipation rate for impellers. AIChE journal, (9): p Kulkarni, A.A., et al., Fractal Impeller for Stirred Tank Reactors. Industrial & Engineering Chemistry Research. 50(12): p
Calculation of Power, Shear and Gas-liquid mass transfer in reactors for fermentation.
VISIMIX TURBULENT. GAS-LIQUID MIXING. FERMENTATION. Calculation of Power, Shear and Gas-liquid mass transfer in reactors for fermentation. 1. Subject of calculations and initial data. This example demonstrates
Application of the CFD method for modelling of floating particles suspension
Application of the CFD method for modelling of floating particles suspension Joanna Karcz, Lukasz Kacperski, Marcelina Bitenc Szczecin University of Technology, Dept. of Chem. Eng. al. Piastow 42, PL-7-65
PIV MEASUREMENTS AND CFD SIMULATION OF VISCOUS FLUID FLOW IN A STIRRED TANK AGITATED BY A RUSHTON TURBINE
Fifth International Conference on CFD in the Process Industries CSIRO, Melbourne, Australia 3-5 December 26 PIV MEASUREMENTS AND CFD SIMULATION OF VISCOUS FLUID FLOW IN A STIRRED TANK AGITATED BY A RUSHTON
Liquid Mixing in Agitated Vessels
100 5 Liquid Mixing in Agitated essels To express the degree of mixing in a stirred vessel, an expression is desirable to show how far the state of mixing deviates from the ideal complete mixing. The most
ENGG 199 Reacting Flows Spring Lecture 2b Blending of Viscous, Non-Newtonian Fluids
ENGG 199 Reacting Flows Spring 2006 Lecture 2b Blending of Viscous, Non-Newtonian Fluids Copyright 2000, A.. Etchells, R..Grenville & R.D. LaRoche All rights reserved. Re-Cap In turbulent regime, viscosity
MASS TRANSFER COEFFICIENTS DURING AERATION BY A SELF-ASPIRATING IMPELLER
th European Conference on Mixing Warszawa, - September MASS TRANSFER COEFFICIENTS DURING AERATION BY A SELF-ASPIRATING IMPELLER Czesław Kuncewicz, Jacek Stelmach Lodz University of Technology, Department
EVALUATION OF THE EFFECT OF PITCHED BLADE TURBINE ON MIXING IN AN ELECTROCHEMICAL REACTOR WITH ROTATING RING ELECTRODES.
EVALUATION OF THE EFFECT OF PITCHED BLADE TURBINE ON MIXING IN AN ELECTROCHEMICAL REACTOR WITH ROTATING RING ELECTRODES. Sergio A. Martinez, Universidad Autónoma Metropolitana, México D.F. Mex., Jorge
AGITATION AND AERATION
AGITATION AND AERATION Although in many aerobic cultures, gas sparging provides the method for both mixing and aeration - it is important that these two aspects of fermenter design be considered separately.
Experimental identification of the flow vortex structures generated in the agitated vessels
Experimental identification of the flow vortex structures generated in the agitated vessels D. JASIKOVA, B. KYSELA, M. KOTEK, V. KOPECKY Institute for Nanomaterials, Advanced Technologies and Innovation
CFD SIMULATION OF SOLID-LIQUID STIRRED TANKS
CFD SIMULATION OF SOLID-LIQUID STIRRED TANKS Divyamaan Wadnerkar 1, Ranjeet P. Utikar 1, Moses O. Tade 1, Vishnu K. Pareek 1 Department of Chemical Engineering, Curtin University Perth, WA 6102 r.utikar@curtin.edu.au
Chaos in mixing vessels
Chaos in mixing vessels Pavel Hasal and Ivan Fořt 2 Institute of Chemical Technology, Prague Department of Chemical Engineering CZ-66 28 Praha 6, Czech Republic (e-mail: Pavel.Hasal@vscht.cz) 2 Czech Technical
AN INVESTIGATION INTO DIFFERENT POWER CONSUMPTION PARAMETERS OF RUSHTON TURBINES: A COMPUTATIONAL SURVEY
Mohammad-Reza Ashory Farhad Talebi Heydar Roohi Ghadikolaei Morad Karimpour https://doi.org/10.21278/tof.41404 ISSN 1333-1124 eissn 1849-1391 AN INVESTIGATION INTO DIFFERENT POWER CONSUMPTION PARAMETERS
CFD SIMULATIONS OF SINGLE AND TWO-PHASE MIXING PROESSES IN STIRRED TANK REACTORS
CFD SIMULATIONS OF SINGLE AND TWO-PHASE MIXING PROESSES IN STIRRED TANK REACTORS Hristo Vesselinov Hristov, Stephan Boden, Günther Hessel, Holger Kryk, Horst-Michael Prasser, and Wilfried Schmitt. Introduction
Mixing Performance of Counter-Axial Flow Impeller using Computational Fluid Dynamics
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2018 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Mixing
THINK FLUID DYNAMIX Mixing, Homogenization & Blend Time. THINK Fluid Dynamix
THINK FLUID DYNAMIX Mixing, Homogenization & Blend Time Provided by: THINK Fluid Dynamix Am Pestalozziring 21 D-91058 Erlangen (Germany) Tel. +49 (0)9131 69098-00 http://www.think-fd.com CFD ENGINEERING
NUMERICAL STUDY OF THE EFFECT OF BLADE SZE ON PUMPING EFFECTIVENESS OF A PADDLE IMPELLER IN AN UNBAFFLED MIXING VESSEL
Third International Conference on CFD in the Minerals and Process Industries CSIRO, Melbourne, Australia 10-12 December 2003 NUMERICAL STUDY OF THE EFFECT OF BLADE SZE ON PUMPING EFFECTIVENESS OF A PADDLE
Numerical Comparison of Rushton Turbine and CD-6 Impeller in Non-Newtonian Fluid Stirred Tank Akhilesh Khapre, Basudeb Munshi
Vol:8, No:11, 014 Numerical Comparison of Rushton Turbine and CD-6 Impeller in Non-Newtonian Fluid Stirred Tan Ahilesh Khapre, Basudeb Munshi Abstract A computational fluid dynamics simulation is done
Effect of the Tank Design on the Flow Pattern Generated with a Pitched Blade Turbine
International Journal of Mechanics and Applications 2012, 2(1): 12-19 DOI: 10.5923/j.mechanics.20120201.03 Effect of the Tank Design on the Flow Pattern Generated with a Pitched Blade Turbine M. Ammar,
PIV Measurements to Study the Effect of the Reynolds Number on the Hydrodynamic Structure in a Baffled. Vessel Stirred by a Rushton Turbine
American Journal of Energy Research, 2014, Vol. 2, No. 3, 67-73 Available online at http://pubs.sciepub.com/ajer/2/3/4 Science and Education Publishing DOI:10.12691/ajer-2-3-4 PIV Measurements to Study
PLO MIXING AND RTD IN TANKS: RADIOTRACER EXPERIMENTS AND CFD SIMULATIONS
PLO522 MIXING AND RTD IN TANKS: RADIOTRACER EXPERIMENTS AND CFD SIMULATIONS A. R. Thatte and A. W. Patwardhan Institute of Chemical Techno lou Uiversity of Mumhai, Mumbai, India H. J. PantV. K. Sharma,
ARTICLE IN PRESS. chemical engineering research and design x x x ( ) xxx xxx. Contents lists available at ScienceDirect
chemical engineering research and design x x x (2 0 0 9) xxx xxx Contents lists available at ScienceDirect Chemical Engineering Research and Design journal homepage: www.elsevier.com/locate/cherd Ekman
Characterization of Laminar Flow and Power Consumption in a Stirred Tank by a Curved Blade Agitator
Proceedings of the International Conference on Heat Transfer and Fluid Flow Prague, Czech Republic, August 11-12, 2014 Paper No. 11 Characterization of Laminar Flow and Power Consumption in a Stirred Tank
CFD ANALYSIS OF TURBULENCE EFFECT ON REACTION IN STIRRED TANK REACTORS
CFD ANALYSIS OF TURBULENCE EFFECT ON REACTION IN STIRRED TANK REACTORS Udaya Bhaskar Reddy R*, Gopalakrishnan S, Ramasamy E Department of Chemical Engineering, Coimbatore Institute of Technology, Coimbatore-
THE DETAILS OF THE TURBULENT FLOW FIELD IN THE VICINITY OF A RUSHTON TURBINE
14 th European Conference on Mixing Warszawa, 10-13 September 2012 THE DETAILS OF THE TURBULENT FLOW FIELD IN THE VICINITY OF A RUSHTON TURBINE Harry E.A. Van den Akker Kramers Laboratorium, Dept. of Multi-Scale
Effect of Baffles Geometry on Hydrodynamics in a Mechanically Agitated System
Effect of Baffles Geometry on Hydrodynamics in a Mechanically Agitated System L. Benyamina 1, M. Bouanini 2 and R. Abdeldjebar 3 1 PhD in Physics Energetics, 2 Doctor in Energy Physics, 3 Magister Energy
Study on residence time distribution of CSTR using CFD
Indian Journal of Chemical Technology Vol. 3, March 16, pp. 114-1 Study on residence time distribution of CSTR using CFD Akhilesh Khapre*, Divya Rajavathsavai & Basudeb Munshi Department of Chemical Engineering,
An Overview of Impellers, Velocity Profile and Reactor Design
An Overview of s, Velocity Profile and Reactor Design Praveen Patel 1, Pranay Vaidya 1, Gurmeet Singh 2 1 Indian Institute of Technology Bombay, India 1 Indian Oil Corporation Limited, R&D Centre Faridabad
PIV Study of the Turbulent Flow in a Stirred Vessel Equipped by an Eight Concave Blades Turbine
Fluid Mechanics 2015; 1(2): 5-10 Published online August 31, 2015 (http://www.sciencepublishinggroup.com/j/fm) doi: 10.11648/j.fm.20150102.11 PIV Study of the Turbulent Flow in a Stirred Vessel Equipped
APPLICATION OF MODELS WITH DIFFERENT COMPLEXITY FOR A STIRRED TANK REACTOR
HUNGARIAN JOURNAL OF INDUSTRIAL CHEMISTRY VESZPRÉM Vol. 39(3) pp. 335-339 (011) APPLICATION OF MODELS WITH DIFFERENT COMPLEXITY FOR A STIRRED TANK REACTOR A. EGEDY, T. VARGA, T. CHOVÁN University of Pannonia,
We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors
We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists 3,500 108,000 1.7 M Open access books available International authors and editors Downloads Our
mixing of fluids MIXING AND AGITATION OF FLUIDS
Levenspiel [2] considered when two fluids are mixed together, the molecular behavior of the dispersed fluid falls between two extremes. If molecules are completely free to move about, the dispersed fluid
The experimental study of the coherent structures generated in the agitated vessels and effected by fluid viscosity
The experimental study of the coherent structures generated in the agitated vessels and effected by fluid viscosity D. Jasikova, B. Kysela, M. Kotek, and V. Kopecky Abstract This paper presents results
PARTICLE IMAGE VELOCIMETRY MEASUREMENTS IN AN AERATED STIRRED TANK
Chem. Eng. Comm., 189: 1208 1221, 2002 Copyright # 2002 Taylor & Francis 0098-6445/02 $12.00 +.00 DOI: 10.1080=00986440290012582 PARTICLE IMAGE VELOCIMETRY MEASUREMENTS IN AN AERATED STIRRED TANK NIELS
THE VELOCITY FIELD IN THE DISCHARGE STREAM FROM A RUSHTON TURBINE IMPELLER
4 th European Conference on Mixing Warszawa, September THE VELOCITY FIELD IN THE DISCHARGE STREAM FROM A RUSHTON TURBINE IMPELLER Jan Talaga a, Ivan Fořt b a Cracow University of Technology, Institute
PHEN 612 SPRING 2008 WEEK 12 LAURENT SIMON
PHEN 612 SPRING 28 WEEK 12 LAURENT SIMON Mixing in Reactors Agitation, Mixing of Fluids and Power requirements Agitation and mixing are two of the most common operations in the processing industries Agitation:
ASSESSMENT OF THE MINIMUM POWER REQUIREMENTS FOR COMPLETE SUSPENSION IN TOP-COVERED UNBAFFLED STIRRED TANKS
4 th European Conference on Mixing Warszawa, 0-3 September 202 ASSESSMENT OF THE MINIMUM POWER REQUIREMENTS FOR COMPLETE SUSPENSION IN TOP-COVERED UNBAFFLED STIRRED TANKS Alessandro Tamburini a, Andrea
Estimation of Agitator Flow Shear Rate
Estimation of Agitator Flow Shear Rate Jie Wu, Lachlan J. Graham, and Nabil Noui Mehidi Fluids Engineering Research Laboratory, Commonwealth Scientific and Industrial Research Organization (CSIRO), Highett
MASS TRANSFER EFFICIENCY IN SX MIXERS
MASS TRANSFER EFFICIENCY IN SX MIXERS By R. Sheinman, Y. Kootov, L. Braginsy, J. Riordan, M. Vancas Turbulent Technologies Ltd. Israel Tenova Bateman Advanced Technologies Ltd. Israel, Australia ABSTRACT
Characterization of Trailing Vortices Generated by a Rushton Turbine
Characterization of Trailing Vortices Generated by a Rushton Turbine Renaud Escudié, Denis Bouyer, and Alain Liné Laboratoire d Ingénierie des Procédés de l Environnement, Institut National des Sciences
Dynamic Effect of Discharge Flow of a Rushton Turbine Impeller on a Radial Baffle J. Kratěna, I. Fořt, O. Brůha
Dynamic Effect of Discharge Flow of a Rushton Turbine Impeller on a Radial Baffle J. Kratěna, I. Fořt, O. Brůha This paper presents an analysis of the mutual dynamic relation between the impeller discharge
Numerical Simulation of Flow Field in a Elliptic Bottom Stirred Tank with Bottom Baffles
Numerical Simulation of Flow Field in a Elliptic Bottom Stirred Tank with Bottom Baffles Liu Xuedong, Liu Zhiyan Abstract When the crisscross baffles and logarithmic spiral baffles are placed on the bottom
Comparison of Different Techniques for Modelling of Flow Field and Homogenization in Stirred Vessels*
Comparison of Different Techniques for Modelling of Flow Field and Homogenization in Stirred Vessels* M. MOŠTĚK**, A. KUKUKOVÁ, M. JAHODA, and V. MACHOŇ Department of Chemical Engineering, Faculty of Chemical
CFD Analysis of a Stirred Vessel Bioreactor with Double Pitch Blade and Rushton Type Impellers
CFD Analysis of a Stirred Vessel Bioreactor with Double Pitch Blade and Rushton Type Impellers A. Buss 1, 2, A. Suleiko 2, 3, K. Rugele 2, J. Vanags 3 1. Riga Biomaterials Innovation and Development Centre,
Blade Angle Effects on the Flow in a Tank Agitated by the Pitched-Blade Turbine
Yeng-Yung Tsui 1 Professor e-mail: yytsui@mail.nctu.edu.tw Jian-Ren Chou Graduate Student Yu-Chang Hu Graduate Student Department of Mechanical Engineering, National Chiao Tung University, Hsinchu 300,
Power requirements for yield stress fluids in a vessel with forward-reverse rotating impeller
Available online at www.sciencedirect.com Procedia Engineering 42 (2012 ) 1437 1444 20 th International Congress of Chemical and Process Engineering CHISA 2012 25 29 August 2012, Prague, Czech Republic
Turbulence Characteristics in a Rushton Stirring Vessel: A Numerical Investigation
urbulence Characteristics in a Rushton Stirring Vessel: A Numerical Investigation Mohammad Amin Rashidifar 1 and Ali Amin Rashidifar 2 1 Department of Mechanical Engineering, Islamic Azad University, Shadegan
CFD Analysis and Experimental Evaluation of the Effective Parameters on Paint Homogeneity in Mixing Tanks
ISTP-16, 2005, PRAGUE 16 TH INTERNATIONAL SYMPOSIUM ON TRANSPORT PHENOMENA CFD Analysis and Experimental Evaluation of the Effective Parameters on Paint Homogeneity in Mixing Tanks N. K. Mohtaram*, M.
ENGG 199 Reacting Flows Spring Lecture 4 Gas-Liquid Mixing Reactor Selection Agitator Design
ENGG 199 Reacting Flows Spring 2006 Lecture 4 Gas-Liquid Mixing Reactor Selection gitator Design Copyright 2000,.W. Etchells, R.K.Grenville & R.D. LaRoche ll rights reserved. Background Roughly 25 % of
Large eddy simulations of flow instabilities in a stirred tank generated by a Rushton turbine *
Large eddy simulations of flow instabilities in a stirred tank generated by a Rushton turbine * FAN Jianhua ( 樊建华 ) a,b, WANG undong ( 王运东 ) a, FEI Weiyang ( 费维扬 ) a a The State Key Laboratory of Chemical
Best Practice Guidelines for Computational Turbulent Dispersed Multiphase Flows. René V.A. Oliemans
Best Practice Guidelines for Computational Turbulent Dispersed Multiphase Flows René V.A. Oliemans ERCOFTAC Seminar, Innventia, Stockholm, June 7-8, 2011 1 Vermelding onderdeel organisatie Department of
Three-dimensional measurements in the baffle region of a turbulently stirred tank
Three-dimensional measurements in the baffle region of a turbulently stirred tank Proceedings of European Congress of Chemical Engineering (ECCE-6) Copenhagen, 16-20 September 2007 Three-dimensional measurements
Effect of Geometry on the Mechanisms for Off-Bottom Solids Suspension in a Stirred Tank
Effect of Geometry on the Mechanisms for Off-Bottom Solids Suspension in a Stirred Tank Inci Ayranci 1*, Márcio B. Machado 1, Adam M. Madej 2, Jos J. Derksen 1, David S. Nobes 2, and Suzanne M. Kresta
THINK Fluid Dynamix THINK FLUID DYNAMIX. CFD for Aeration Applications
THINK FLUID DYNAMIX Provided by: THINK Fluid Dynamix Am Pestalozziring 21 D-91058 Erlangen (Germany) Tel. +49 (0)9131 69098-00 http://www.think-fd.com CFD ENGINEERING & CONSULTING THINK Fluid Dynamix is
Separationsteknik / Separation technology
Separationsteknik / Separation technology 424105 9. Mixning, omrörning och blandning / Mixing, stirring and blending Ron Zevenhoven Åbo Akademi University Thermal and Flow Engineering Laboratory / Värme-
Assessing Mixing Sensitivities for Scale-up. Matthew Jörgensen Atlanta, 10/20/2014
Assessing Mixing Sensitivities for Scale-up Matthew Jörgensen Atlanta, 10/20/2014 Nalas: Solutions that Scale! Engineering Services Broad range of services & capabilities supporting chemical process development
Experiments at the University of Minnesota (draft 2)
Experiments at the University of Minnesota (draft 2) September 17, 2001 Studies of migration and lift and of the orientation of particles in shear flows Experiments to determine positions of spherical
Evaluation and accuracy of the local velocity data measurements in an agitated vessel
EPJ Web of Conferences 67, 02065 (2014) DOI: 10.1051/ epjconf/20146702065 C Owned by the authors, published by EDP Sciences, 2014 Evaluation and accuracy of the local velocity data measurements in an agitated
AN OVERVIEW OF IMPELLERS, VELOCITY PROFILES AND REACTOR DESIGN
AN OVERVIEW OF IMPELLERS, VELOCITY PROFILES AND REACTOR DESIGN Instructor: Gurmeet Singh (Department Manager of Polymer and Processing Department IOCL R&D center, Faridabad) 1 Presented by: Pranay. K.
INVESTIGATION OF TURBULENCE MODULATION IN SOLID- LIQUID SUSPENSIONS USING PARALLEL COMPETING REACTIONS AS PROBES FOR MICRO-MIXING EFFICIENCY
14 th European Conference on Mixing Warszawa, 1-13 eptember 212 INVETIGATION OF TURBULENCE MODULATION IN OLID- LIUID UPENION UING PARALLEL COMPETING REACTION A PROBE FOR MICRO-MIING EFFICIENCY H. Unadkat,
Modeling of turbulence in stirred vessels using large eddy simulation
Modeling of turbulence in stirred vessels using large eddy simulation André Bakker (presenter), Kumar Dhanasekharan, Ahmad Haidari, and Sung-Eun Kim Fluent Inc. Presented at CHISA 2002 August 25-29, Prague,
1. Starting of a project and entering of basic initial data.
PROGRAM VISIMIX TURBULENT SV. Example 1. Contents. 1. Starting of a project and entering of basic initial data. 1.1. Opening a Project. 1.2. Entering dimensions of the tank. 1.3. Entering baffles. 1.4.
ALTERNATE OPERATING METHODS FOR IMPROVING THE PERFORMANCE OF CONTINUOUS STIRRED TANK REACTORS
ALTERNATE OPERATING METHODS FOR IMPROVING THE PERFORMANCE OF CONTINUOUS STIRRED TANK REACTORS J. AUBIN a *, S.M. KRESTA b, J. BERTRAND a, C. XUEREB a and D.F. FLETCHER c a Laboratoire de Génie Chimique,
Oxygen transfer, mixing time and gas holdup characterization in a hybrid bioreactor
Oxygen transfer, mixing time and gas holdup characterization in a hybrid bioreactor Proceedings of European Congress of Chemical Engineering (ECCE-6) Copenhagen, 16-2 September 27 Oxygen transfer, mixing
AGITATION/GAS-LIQUID DISPERSION. CHEM-E Fluid Flow in Process Units
AGITATION/GAS-LIQUID DISPERSION CHEM-E7160 - Fluid Flow in Process Units 1. INTRODUCTION Agitation: Mixing: Blending: Suspension: Dispersion: Induced motion of a material in a specific way, usually in
We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors
We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists 4,000 116,000 120M Open access books available International authors and editors Downloads Our
PIV STUDY OF MIXING CHARACTERISTICS IN A STIRRED VESSEL WITH A NON-NEWTONIAN FLUID
4 th European Conference on Mixing Warszawa, - September PIV STUDY OF MIXING CHARACTERISTICS IN A STIRRED VESSEL WITH A NON-NEWTONIAN FLUID J.-C. Gabelle abce, A. Liné abc, J. Morchain abc, D. Anne-Archard
PIV measurement and study on turbulence generator flow field of medium consistency pump
IOP Conference Series: Earth and Environmental Science PAPER OPEN ACCESS PIV measurement and study on turbulence generator flow field of medium consistency pump To cite this article: D X Ye et al 018 IOP
The Role of Rheology in the Flow and Mixing of. Complex Fluids
The Role of Rheology in the Flow and Mixing of Complex Fluids by Sara Ghorbanian Farah Abadi A thesis submitted to The University of Birmingham for the degree of MASTER OF PHILOSOPHY School of Chemical
Numerical Simulation Analysis of Ultrafine Powder Centrifugal Classifier Bizhong XIA 1, a, Yiwei CHEN 1, b, Bo CHEN 2
5th International Conference on Information Engineering for Mechanics and Materials (ICIMM 2015) Numerical Simulation Analysis of Ultrafine Powder Centrifugal Classifier Bizhong XIA 1, a, Yiwei CHEN 1,
Dense Solid-Liquid Suspensions in Top-Covered Unbaffled Stirred Vessels
Dense Solid-Liquid Suspensions in Top-Covered Unbaffled Stirred Vessels Alessandro Tamburini*, Andrea Cipollina, Giorgio Micale, Alberto Brucato Dipartimento di Ingegneria Chimica, Gestionale, Informatica,
Effect of the Type of Impellers on Mixing in an Electrochemical Reactor
A publication of VOL. 35, 2013 CHEMICAL ENGINEERING TRANSACTIONS Guest Editors: Petar Varbanov, Jiří Klemeš, Panos Seferlis, Athanasios I. Papadopoulos, Spyros Voutetakis Copyright 2013, AIDIC Servizi
Principles of Convection
Principles of Convection Point Conduction & convection are similar both require the presence of a material medium. But convection requires the presence of fluid motion. Heat transfer through the: Solid
vector H. If O is the point about which moments are desired, the angular moment about O is given:
The angular momentum A control volume analysis can be applied to the angular momentum, by letting B equal to angularmomentum vector H. If O is the point about which moments are desired, the angular moment
Computer Life (CPL) ISSN: The Numerical Simulation on Internal Gas-liquid Two Phase Flow Field of. Three Layers of Air Stirred Reactor
Computer Life (CPL) ISSN: 1819-4818 DELIVERING QUALITY SCIENCE TO THE WORLD The Numerical Simulation on Internal Gas-liquid Two Phase Flow Field of Three Layers of Air Stirred Reactor Haiyue Wang*, Zhixi
Calculation of Power and Flow Capacity of Rotor / Stator Devices in VisiMix RSD Program.
Calculation of Power and Flow Capacity of Rotor / Stator Devices in VisiMix RSD Program. L.N.Braginsky, D.Sc. (Was invited to be presented on the CHISA 2010-13th Conference on Process Integration, Modelling
INVESTIGATIONS OF MASS TRANSFER AND MICROMIXING EFFECTS IN TWO-PHASE LIQUID-LIQUID SYSTEMS WITH CHEMICAL REACTION
14 th European Conference on Mixing Warszawa, 10-13 September 20 INVESTIGATIONS OF MASS TRANSFER AND MICROMIXING EFFECTS IN TWO-PHASE LIQUID-LIQUID SYSTEMS WITH CHEMICAL REACTION M. Jasińska a, J. Bałdyga
Investigation of Flow Profile in Open Channels using CFD
Investigation of Flow Profile in Open Channels using CFD B. K. Gandhi 1, H.K. Verma 2 and Boby Abraham 3 Abstract Accuracy of the efficiency measurement of a hydro-electric generating unit depends on the
Chemical Engineering Science
Chemical Engineering Science 79 (212) 163 176 Contents lists available at SciVerse ScienceDirect Chemical Engineering Science journal homepage: www.elsevier.com/locate/ces Effect of geometry on the mechanisms
Comparison of Agitators Performance for Particle Suspension in Top-Covered Unbaffled Vessels
585 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 43, 205 Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 205, AIDIC Servizi S.r.l., ISBN 978-88-95608-34-; ISSN 2283-926 The Italian Association
Effect of a Continuous Feed on the Fluid-Dynamics of a Mechanically Stirred Tank
1609 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 43, 2015 Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 2015, AIDIC Servizi S.r.l., ISBN 978-88-95608-34-1; ISSN 2283-9216 The Italian
Modelling and Simulation of a Batch Poly(Vinyl Chloride) Reactor
769 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 32, 23 Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 23, AIDIC Servizi S.r.l., ISBN 978-88-968-23-; ISSN 974-979 The Italian Association
COMPUTATIONAL FLOW ANALYSIS THROUGH A DOUBLE-SUCTION IMPELLER OF A CENTRIFUGAL PUMP
Proceedings of the Fortieth National Conference on Fluid Mechanics and Fluid Power December 12-14, 2013, NIT Hamirpur, Himachal Pradesh, India FMFP2013_141 COMPUTATIONAL FLOW ANALYSIS THROUGH A DOUBLE-SUCTION
CFD Modelling of the Fluid Flow Characteristics in an External-Loop Air-Lift Reactor
A publication of 145 CHEMICAL ENGINEERING TRANSACTIONS VOL. 2, 21 Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 21, AIDIC Servizi S.r.l., ISBN 978-88-958-2-5; ISSN 1974-9791 The Italian Association
THE COMPUTATIONAL-FLUID-DYNAMICS STUDY OF AN UNBAFFLED STIRRED VESSEL WITH ECCENTRICALLY POSITIONED IMPELLER
RYSZARD WÓJTOWICZ *, ANDREY A. LIPIN ** THE COMPUTATIONAL-FLUID-DYNAMICS STUDY OF AN UNBAFFLED STIRRED VESSEL WITH ECCENTRICALLY POSITIONED IMPELLER SYMULACJE CFD MIESZALNIKA BEZ PRZEGRÓD Z NIECENTRYCZNIE
RELATION BETWEEN PARTICLE RISING BEHAVIOR AND LIQUID FLOW AROUND THE BOTTOM OF A STIRRED VESSEL
14 th European Conference on Mixing Warszawa, 10-13 September 2012 RELATION BETWEEN PARTICLE RISING BEHAVIOR AND LIQUID FLOW AROUND THE BOTTOM OF A STIRRED VESSEL Ryuta Misumi a, Takuji Sasaki b, Hayato
Modeling Industrial Crystallizers
Modeling Industrial Crystallizers Kumar Dhanasekharan, Ph.D. Fluent Inc., 10 Cavendish Court, Lebanon, NH 03766 Phone: (603) 643-2600 x323; Email: kd@fluent.com One of the main challenges in industrial
NUMERICAL AND EXPERIMENTAL STUDIES OF LIQUID-LIQUID MIXING IN A KENICS STATIC MIXER
14 th European Conference on Mixing Warszawa, 10-13 September 2012 NUMERICAL AND EXPERIMENTAL STUDIES OF LIQUID-LIQUID MIXING IN A KENICS STATIC MIXER Zdzislaw Jaworski a, Halina Murasiewicz a, a Institute
Optimum Configuration of a Double Jet Mixer Using DOE
Optimum Configuration of a Double Jet Mixer Using DOE Manjula. P, Kalaichevi. P, Annadurai. G and Dheenathayalan. K Abstract Mixing is used for blending of liquids, flocculation, homogenization of mixtures,
Angular momentum equation
Angular momentum equation For angular momentum equation, B =H O the angular momentum vector about point O which moments are desired. Where β is The Reynolds transport equation can be written as follows:
Simulation of Flow Pattern through a Three-Bucket Savonius. Wind Turbine by Using a Sliding Mesh Technique
Simulation of Flow Pattern through a Three-Bucket Savonius Wind Turbine by Using a Sliding Mesh Technique Dr. Dhirgham AL-Khafaji Department of Mechanical engineering/college of Engineering, University
AIRLIFT BIOREACTORS. contents
AIRLIFT BIOREACTORS contents Introduction Fluid Dynamics Mass Transfer Airlift Reactor Selection and Design 1 INTRODUCTION airlift reactor (ALR) covers a wide range of gas liquid or gas liquid solid pneumatic
CFD Simulation in Helical Coiled Tubing
Journal of Applied Science and Engineering, Vol. 19, No. 3, pp. 267 272 (2016) DOI: 10.6180/jase.2016.19.3.04 CFD Simulation in Helical Coiled Tubing Z. Y. Zhu Department of Petroleum Engineering, China
Flow analysis in centrifugal compressor vaneless diffusers
348 Journal of Scientific & Industrial Research J SCI IND RES VOL 67 MAY 2008 Vol. 67, May 2008, pp. 348-354 Flow analysis in centrifugal compressor vaneless diffusers Ozturk Tatar, Adnan Ozturk and Ali
APPLICATION OF STIRRED TANK REACTOR EQUIPPED WITH DRAFT TUBE TO SUSPENSION POLYMERIZATION OF STYRENE
APPLICATION OF STIRRED TANK REACTOR EQUIPPED WITH DRAFT TUBE TO SUSPENSION POLYMERIZATION OF STYRENE Masato TANAKAand Takashi IZUMI Department of Chemical Engineering, Niigata University, Niigata 950-21
Numerical Evaluation of Mixing Time in a Tank Reactor Stirred by a Magnetically Driven Impeller
6836 Ind. Eng. Chem. Res. 2004, 43, 6836-6846 Numerical Evaluation of Mixing Time in a Tank Reactor Stirred by a Magnetically Driven Impeller Marina Campolo Instituto Pluridisciplinar, Universidad Complutense
Scale Up of Liquid and Semisolid Manufacturing Processes
Scale Up of Liquid and Semisolid Manufacturing Processes Lawrence H. Block The author points out some major obstacles to effective scale-up and describes methods available to pharmaceutical scientists
A study of mixing by PIV and PLIF in bioreactor of animal cell culture
Sixth International Symposium on Mixing in Industrial Process Industries ISMIP VI Niagara on the Lake, Niagara Falls, Ontario, Canada August 17-21, 2008 A study of mixing by PIV and PLIF in bioreactor
Review of the Main Mathematical Models Used in VisiMix
Review of the Main Mathematical Models Used in VisiMix Simulation of Mixing-Related Processes for Chemical Engineers Mixing in low viscosity fluids and multiphase systems. Flow pattern, phase distribution,
Reynolds Number Scaling of Flow in a Rushton Turbine Stirred Tank. Part I Mean Flow, Circular Jet and Tip Vortex Scaling
Reynolds Number Scaling of Flow in a Rushton Turbine Stirred Tank. Part I Mean Flow, Circular Jet and Tip Vortex Scaling H.S. Yoon 1, D.F. Hill 2, S. Balachandar 3*, R.J. Adrian 3, M.Y. Ha 1 1 School of
Flow structures in solid-liquid suspensions in mixing and confined jets
THESIS FOR THE DEGREE OF LICENTIATE OF ENGINEERING Flow structures in solid-liquid suspensions in mixing and confined jets MATTHIAS ENG Chemical Engineering Department of Chemical and Biological Engineering