Chemistry 151 Last Updated Dec Lab 10: The Neutralizing Ability of an Antacid (Titrations, Pt II)

Size: px
Start display at page:

Download "Chemistry 151 Last Updated Dec Lab 10: The Neutralizing Ability of an Antacid (Titrations, Pt II)"

Transcription

1 Chemistry 151 Last Updated Dec Lab 10: The Neutralizing Ability of an Antacid (Titrations, Pt II) Introduction The active ingredient of many antacids is a base that neutralizes excess stomach acid, hydrochloric acid (HCl) in a simple acid-base reaction. For example, Phillips Milk of Magnesia takes its name from its active ingredient, magnesium hydroxide. When reacted with stomach acid, the reaction is Mg(OH) 2(s) + 2HCl(aq) MgCl 2(aq) + H 2O(l) Other antacids use calcium carbonate (CaCO 3) as the active ingredient, which neutralizes the acid by the following reaction. CaCO 3(s) + 2HCl(aq) CaCl 2(aq) + CO 2(g) + H 2O(l) In this lab, you will perform a titration to determine the acid-neutralizing capability of a commercial antacid containing calcium carbonate. Unlike the KHP used in the previous week titration, though, most antacid tablets have poor solubility in water (see equations above), which can affect the accuracy of your titration. So instead of titrating the antacid directly, you will first neutralize the antacid with an excess amount of hydrochloric acid then determine the amount of excess HCl present by titrating it with sodium hydroxide (NaOH). NaOH(aq) + HCl(aq) NaCl(aq) + H 2O(l) This technique is often referred to as a back-titration. Once you know the amount of excess HCl, you can determine the amount required to neutralize the antacid tablet. In this lab You will be using the same 1M NaOH solutions you standardized during the previous lab, so unless notified by your instructor you should use your calculated concentration from that lab. The HCl solutions have already been standardized for you. The indicator used in this lab will be bromophenol blue, which is yellow in acidic solution and blue in basic. Ideally the solution will turn green at endpoint (yellow + blue = green), but the green range is narrow enough that it can be difficult to see this color. You ll most likely see it jump straight from yellow to blue with your final drop of titrant, but this won t adversely affect your calculations. Before you perform the titration, however, we must first boil the solution to remove any dissolved CO 2. If not removed, the CO 2 can react with water to form carbonic acid (H 2CO 3), which can react with calcium chloride to precipitate calcium carbonate and form additional HCl. When this occurs, the trial becomes unusable. CO 2(aq) + H 2O(l) H 2CO 3(aq) H 2CO 3(aq) + CaCl 2(aq) CaCO 3(s) + 2HCl(aq)

2 Procedure Part I: Preparing the Buret 1. Attach a buret clamp to a ring stand. 2. Add 20 ml 1 M sodium hydroxide (which you prepared as part of the previous lab) to a buret and place the buret in the clamp. Inspect the stopper for leaks. If you see any, inform your instructor before continuing. 3. Slowly pour the sodium hydroxide into the sink, rotating the buret as you do in order to clean as much of the inside as possible. Repeat this step with an additional 20mL of sodium hydroxide. 4. Clamp the buret and fill it to the 0.0 ml mark with sodium hydroxide. If air bubbles form, try to remove as many as you can by gently tapping the side of the buret. Part II: Neutralizing the Antacid 1. Obtain an antacid tablets from your instructor measure its mass. 2. Place a tablet in an Erlenmeyer flask and add 75 ml water. 3. Using a volumetric pipet, transfer ml of hydrochloric acid (approx. 0.6 M) to the flask and mix (the tablet may not completely dissolve). 4. Use a hot plate to boil the solution (vigorously) for 20 minutes. Part III: Performing the Back-titration 1. With the solution still warm, add 8 drops of bromophenol blue to the antacid solution. 2. Begin titrating sodium hydroxide to the solution. As soon as you see a green or blue color appear in the solution, turn off the valve. [Note: if you start to see a precipitate form, stop titrating immediately, as you re most likely forming calcium carbonate (see intro). Boil the solution for another ten minutes then continue with the titration.] 3. Swirl the flask to mix the solution then continue adding sodium hydroxide dropwise to flask. Continue swirling the flask as you add titrant until a green or blue color persists for 30 seconds. Repeat Parts II and III with a second tablet. Do not refill the buret unless it appears that you won t have enough to perform the next determination. Only perform a third trial if one of the first two becomes unusable because of excess CaCO 3 formation. Waste Disposal All waste can be poured down the sink with running water. Rinse you buret with water to remove any remaining traces of NaOH, which can dry up and clog the buret tip.

3 Name: Section: Data Standardized concentration of NaOH, M (from Lab 9) Standardized concentration of HCl, M (from label) Brand of antacid used Trial Mass of tablet, g Volume of HCl added Total moles of HCl added Initial buret reading, ml Final buret reading, ml Volume NaOH titrated, ml Moles NaOH titrated Moles of HCl neutralized by NaOH Moles of HCl neutralized by antacid Moles of CaCO 3 in antacid Mass of CaCO 3 in antacid Mass percentage of CaCO 3 in tablet, g Average mass percent

4 Show your work for each of the following calculations from Trial #1. 1) Volume of NaOH titrated 2) Moles of NaOH titrated 3) Moles of HCl neutralized by NaOH 4) Moles of HCl neutralized by antacid 5) Moles of CaCO 3 in antacid 6) Mass of CaCO 3 in antacid 7) Mass percentage of CaCO 3 in tablet.

5 Name: Section: Post-lab Questions 1. If a student forms CaCO 3 from the presence of carbon dioxide, but continued with the trial anyway, how would this affect his/her calculations (too high, too low, or no effect)? Explain your answers. a) The volume of NaOH required for the back titration. b) The calculated moles of HCl neutralized by the antacid. 2. A student performed Part II as outlined in the procedure, but when he added the bromophenol blue the solution turned blue. a) Why is the solution blue? b) What can the student do to correct for this error and salvage this trial? How should the data sheet be modified to reflect this correction? 3. Some antacid tablets actually contain a mixture of calcium carbonate and magnesium hydroxide (though they usually have the same strength as those that only contain CaCO 3). If this had been the case for the antacid you tested, but you still assumed it only contained CaCO 3, how would this have affected each of the following (too high, too low, or no effect)? Explain. a) Moles of HCl neutralized by the antacid b) Mass percentage of CaCO 3 in tablet.

6 Name: Section: Pre-lab Questions 1. What is meant by a back-titration? Why is it being performed in this lab instead of a direct (normal) titration? 2. The bubbling you see at the start of your heating isn t the solution bubbling. What is it? 3. What color should the solution at the start of the titration performed in this lab? What color should it be when endpoint is reached? 4. How much 1.0 M NaOH would be required to completely neutralize 40.0 ml of 0.60 M HCl? 4. A g antacid tablet, with CaCO 3 as the active ingredient, was mixed was 30.0 ml of M HCl. It took 15.3 ml of M NaOH to neutralize the excess acid. a) Calculate the volume of HCl neutralized by the NaOH. b) Calculate the amount of HCl (in ml) neutralized by the antacid. c) Calculate the mass of CaCO 3 (in g) that reacted with HCl. d) Calculate the mass percent of CaCO 3 present in the antacid.

NEUTRALIZATION TITRATION-2 TITRATION OF AN ANTACID (Exp. 4)

NEUTRALIZATION TITRATION-2 TITRATION OF AN ANTACID (Exp. 4) Objective NEUTRALIZATION TITRATION-2 TITRATION OF AN ANTACID (Exp. 4) The aim of this experiment is to carry out titration of antacid tablets and to determine acetic acid content of vinegar. a) Titration

More information

Name Partner Lab Section M Tu W Th F Chemistry 130 Experiment 6: Titration and Analysis

Name Partner Lab Section M Tu W Th F Chemistry 130 Experiment 6: Titration and Analysis Name Partner Lab Section M Tu W Th F Chemistry 130 Experiment 6: Titration and Analysis Introduction A neutralization reaction is one in which an acid (proton donor) and a base (proton acceptor) react

More information

Experiment #7. Titration of Vinegar

Experiment #7. Titration of Vinegar Experiment #7. Titration of Vinegar Goals 1. To determine the mass percent of acetic acid in a solution via titration. 2. To master the technique of titration. Introduction Vinegar is a common household

More information

The reaction between the metal hydroxides and the stomach acid is an acid base reaction very similar to that in the previous experiment:

The reaction between the metal hydroxides and the stomach acid is an acid base reaction very similar to that in the previous experiment: Experiment 3 Stoichiometry... Solution/Solution Evaluating Commercial Antacid's Lab Owl Announcement Upon completion of this lab go log onto OWL. A Lab Owl section should now appear in your courses and

More information

Experiment #10: Analysis of Antacids

Experiment #10: Analysis of Antacids Experiment #10: Analysis of Antacids Purpose: In this experiment you will prepare one solution that is approximately 0.1 M NaOH. Then you will standardize this solution, which means that you will experimentally

More information

CHM111 Lab Titration of Vinegar Grading Rubric

CHM111 Lab Titration of Vinegar Grading Rubric Name Team Name CHM111 Lab Titration of Vinegar Grading Rubric Criteria Points possible Points earned Lab Performance Printed lab handout and rubric was brought to lab 3 Safety and proper waste disposal

More information

TRATION: ANALYSIS OF VINE

TRATION: ANALYSIS OF VINE Experiment 10 Name: 22 Ti TRATION: ANALYSIS OF VINE 31 Ga R In this experiment, you will learn the concept and technique of titration. You will determine the concentration of acetic acid in commercial

More information

Chem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution, analysis of vinegar & antacid tablets

Chem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution, analysis of vinegar & antacid tablets Chem 2115 Experiment #7 Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution, analysis of vinegar & antacid tablets OBJECTIVE: The goals of this experiment are to learn titration

More information

1. The active ingredients are at best, only sparingly soluble in water. 3. The technique would have to be modified for every different antacid.

1. The active ingredients are at best, only sparingly soluble in water. 3. The technique would have to be modified for every different antacid. Experiment 3 Stoichiometry Solution/Solution Evaluating Commercial Antacid's Lab Owl Announcement: Upon completion of this lab, log onto OWL. Your second Lab Owl assignment, Lab Owl: Exp 3, should appear

More information

Ascorbic Acid Titration of Vitamin C Tablets

Ascorbic Acid Titration of Vitamin C Tablets Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,

More information

Ascorbic Acid Titration of Vitamin C Tablets

Ascorbic Acid Titration of Vitamin C Tablets Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,

More information

Chem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution and the analysis of antacid tablets

Chem 2115 Experiment #7. Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution and the analysis of antacid tablets Chem 2115 Experiment #7 Volumetric Analysis & Consumer Chemistry Standardization of an unknown solution and the analysis of antacid tablets OBJECTIVE: The goals of this experiment are to learn titration

More information

Experiment 7: Titration of an Antacid

Experiment 7: Titration of an Antacid 1 Experiment 7: Titration of an Antacid Objective: In this experiment, you will standardize a solution of base using the analytical technique known as titration. Using this standardized solution, you will

More information

Ascorbic Acid Titration of Vitamin C Tablets

Ascorbic Acid Titration of Vitamin C Tablets Ascorbic Acid Titration of Vitamin C Tablets Introduction This experiment illustrates how titration, the process of slowly adding one solution to another until the reaction between the two is complete,

More information

Experiment 7: ACID-BASE TITRATION: STANDARDIZATION OF A SOLUTION

Experiment 7: ACID-BASE TITRATION: STANDARDIZATION OF A SOLUTION Experiment 7: ACID-BASE TITRATION: STANDARDIZATION OF A SOLUTION Purpose: Determine molarity of a solution of unknown concentration by performing acid-base titrations Performance Goals: Apply the concepts

More information

Experiment 20: Analysis of Vinegar. Materials:

Experiment 20: Analysis of Vinegar. Materials: Experiment 20: Analysis of Vinegar Materials: graduated cylinder 6 M NaOH: Dilute Sodium Hydroxide 1000 ml Florence Flask & stopper KHC 8 H 4 O 4 : Potassium Hydrogen Phthalate (KHP) 125 ml Erlenmeyer

More information

Safety Note: Safety glasses and laboratory coats are required when performing this experiment

Safety Note: Safety glasses and laboratory coats are required when performing this experiment The Determination of Hypochlorite in Bleach Reading assignment: Burdge, Chemistry 4 th edition, section 4.6. We will study an example of a redox titration in order to determine the concentration of sodium

More information

Name: Date: AP Chemistry. Titrations - Volumetric Analysis. Steps for Solving Titration Problems

Name: Date: AP Chemistry. Titrations - Volumetric Analysis. Steps for Solving Titration Problems Name: Date: AP Chemistry Titrations - Volumetric Analysis Term Volumetric analysis Burette Pipette titrate titre aliquot end point equivalence point indicator primary standard standardisation secondary

More information

EXPERIMENT #8 Acid-Base I: Titration Techniques

EXPERIMENT #8 Acid-Base I: Titration Techniques EXPERIMENT #8 Acid-Base I: Titration Techniques OBJECTIVES: Dispense a precise volume of a solution with a buret Titrate a known volume of acid solution with a standard solution of base Reach a proper

More information

Titration of HCl with Sodium Hydroxide

Titration of HCl with Sodium Hydroxide Titration of HCl with Sodium Hydroxide Lab Report for the Subject of Advanced Chemistry Anon Durongpisitkul, Karis Katekovit, Varun Saketharam,Thanon Thamvorapol, Chanon Anektanasup- January 28, 2017 1

More information

NOTE: YOU WILL BE USING THIS SOLUTION IN BOTH, THIS EXPERIMENT AND EXP 12B. IF YOU WASTE THE SOLUTION YOU MAY RUN OUT BEFORE YOU HAVE FINISHED EXP 12B

NOTE: YOU WILL BE USING THIS SOLUTION IN BOTH, THIS EXPERIMENT AND EXP 12B. IF YOU WASTE THE SOLUTION YOU MAY RUN OUT BEFORE YOU HAVE FINISHED EXP 12B EXPERIMENT 12 A: STANDARDIZATION OF A SODIUM HYDROXIDE SOLUTION OBJECTIVE: Sodium hydroxide solution of about 0.2 M is prepared in order to be used in Exp 12B. The solution is then standardized, that is,

More information

Experiment 4, Calculation of Molarity of H 3 PO 4 by Titration with NaOH Chemistry 201, Wright College, Department of Physical Science and Engineering

Experiment 4, Calculation of Molarity of H 3 PO 4 by Titration with NaOH Chemistry 201, Wright College, Department of Physical Science and Engineering Name Date Experiment 4, Calculation of Molarity of H 3 PO 4 by Titration with NaOH Chemistry 201, Wright College, Department of Physical Science and Engineering Molarity is a common unit within the chemical

More information

Acid / Base Titrations

Acid / Base Titrations Acid / Base Titrations v051413_7pm Objectives: Determine the concentration of a base solution using an acid standard. Optional: Precipitate an ionic salt for percent yield determination using the standardized

More information

Ascorbic Acid Titration of Vitamin C Tablets

Ascorbic Acid Titration of Vitamin C Tablets Ascorbic Acid Titration of Vitamin C Tablets Part A. Preparation of Vitamin C Tablet Solutions 1. Obtain two vitamin C tablets. Place a plastic weighing boat on the balance, and press zero to tare the

More information

Chemistry 143 Acid Base Titration Dr. Caddell. Titrating Acid

Chemistry 143 Acid Base Titration Dr. Caddell. Titrating Acid Titrating Acid In this lab you will first determine the concentration of sodium hydroxide in a stock solution that you prepare. You will then use that stock sodium hydroxide solution to titrate a solution

More information

Acid Base Titration Experiment ACID - BASE TITRATION LAB

Acid Base Titration Experiment ACID - BASE TITRATION LAB ACID - BASE TITRATION LAB MATERIALS and CHEMICALS Burette 50 ml Burette clamp Ring stand Stirring rod Plastic funnel Beakers (50 ml, 100 ml, 400 ml) Graduated cylinder (25 ml, 50 ml) 0.10 M NaOH 0.10 M

More information

Synthesis of Benzoic Acid

Synthesis of Benzoic Acid E x p e r i m e n t 5 Synthesis of Benzoic Acid Objectives To use the Grignard reagent in a water free environment. To react the Grignard reagent with dry ice, CO 2(s). To assess the purity of the product

More information

EXPERIMENT #9 PRELAB EXERCISES. Redox Titration (Molarity Version) Name Section. 1. Balance the following redox reaction under acidic conditions.

EXPERIMENT #9 PRELAB EXERCISES. Redox Titration (Molarity Version) Name Section. 1. Balance the following redox reaction under acidic conditions. EXPERIMENT #9 PRELAB EXERCISES Redox Titration (Molarity Version) Name Section 1. Balance the following redox reaction under acidic conditions. C 2 O 2-4 (aq) + MnO - 4 (aq) CO 2 (g) + Mn 2+ (aq) 2. A

More information

Antacid Tables. How effective is that antacid tablet? We are going to use a technique called titration to find out how effective the tabs are.

Antacid Tables. How effective is that antacid tablet? We are going to use a technique called titration to find out how effective the tabs are. Antacid Tables How effective is that antacid tablet? We are going to use a technique called titration to find out how effective the tabs are. There are 4 stations. Each station has one type of antacid.

More information

Titrations Worksheet and Lab

Titrations Worksheet and Lab Titrations Worksheet and Lab Vocabulary 1. Buret: a piece of glassware used for dispensing accurate volumes, generally reads to two places of decimal. 2. Titrant: the substance of known concentration added

More information

+ H 2 O Equation 1. + NaOH CO 2 Na

+ H 2 O Equation 1. + NaOH CO 2 Na Experiment # 5 VINEGAR: AN FDA INVESTIGATION Objective In this experiment, you will play the role of an FDA analytical chemist, You will verify whether a vinegar manufacturer's quality control lab remains

More information

Chemical Reactions: Titrations

Chemical Reactions: Titrations 1 Chemical Reactions: Titrations ORGANIZATION Mode: laboratory work, work in pairs Grading: lab notes, lab performance (titration accuracy), and post-lab report Safety: goggles, lab coat, closed-toe shoes,

More information

Supernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs.

Supernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs. Limiting Reagent Introduction The quantities of substances involved in a chemical reaction represented by a balanced equation are often referred to as stoichiometric amounts. Solution stoichiometry is

More information

Chemistry 143 Experiment #11 Acid Base Titration Dr. Caddell. Titrating Acid

Chemistry 143 Experiment #11 Acid Base Titration Dr. Caddell. Titrating Acid Titrating Acid In this lab you will first determine the concentration of sodium hydroxide in a stock solution that you prepare. You will then use that stock sodium hydroxide solution to titrate a solution

More information

Volumetric Analysis: Analysis of antacid tablets Analysis of Cl - concentrations in IV solutions

Volumetric Analysis: Analysis of antacid tablets Analysis of Cl - concentrations in IV solutions Volumetric Analysis: Analysis of antacid tablets Analysis of Cl - concentrations in IV solutions OBJECTIVE: The goals of this experiment are to learn titration concepts and techniques. SKILLS: Titration,

More information

19.4 Neutralization Reactions > Chapter 19 Acids, Bases, and Salts Neutralization Reactions

19.4 Neutralization Reactions > Chapter 19 Acids, Bases, and Salts Neutralization Reactions Chapter 19 Acids, Bases, and Salts 19.1 Acid-Base Theories 19.2 Hydrogen Ions and Acidity 19.3 Strengths of Acids and Bases 19.4 Neutralization Reactions 19.5 Salts in Solution 1 Copyright Pearson Education,

More information

Experiment: Titration

Experiment: Titration Experiment: Titration INTRODUCTION In this experiment you will be determining the volume of sodium hydroxide solution of known concentration required to neutralize a known mass of an unknown acid in solution.

More information

Supernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs.

Supernatant: The liquid layer lying above the solid layer after a precipitation reaction occurs. Limiting Reagent Introduction The quantities of substances involved in a chemical reaction represented by a balanced equation are often referred to as stoichiometric amounts. Solution stoichiometry is

More information

CHEM 132 Lab 11 Western Carolina University

CHEM 132 Lab 11 Western Carolina University Name Lab Section Chemistry 132 Lab 11 How Effective is Your Antacid? Prelaboratory Exercise 1. How many grams of NaOH will you need to make 250 of 0.5 M NaOH solution? 2. What is the purpose of the first,

More information

Pre-lab: Read section 9.9 (pages ) on acid-base titrations in the textbook. Complete the attached pre-lab by Tuesday, June 2.

Pre-lab: Read section 9.9 (pages ) on acid-base titrations in the textbook. Complete the attached pre-lab by Tuesday, June 2. Chemistry 121 Lab 5: Titration of an unknown acid Objective: Determine the concentration of an unknown monoprotic acid by titration, the process that matches the number of moles of base with the number

More information

NaOH (aq) + HCl (aq) NaCl (aq) + H 2 O (l)

NaOH (aq) + HCl (aq) NaCl (aq) + H 2 O (l) EXPERIMENT 21 Molarity of a Hydrochloric Acid Solution by Titration INTRODUCTION Volumetric analysis is a general term meaning any method in which a volume measurement is the critical operation; however,

More information

Ascorbic Acid Titration of Vitamin C Tablets This lab will be completed individually! Make sure you come prepared!

Ascorbic Acid Titration of Vitamin C Tablets This lab will be completed individually! Make sure you come prepared! Ascorbic Acid Titration of Vitamin C Tablets This lab will be completed individually! Make sure you come prepared! This laboratory experiment has a formal report. Consult the guidelines for writing a formal

More information

TITRATION OF AN ACID WITH A BASE

TITRATION OF AN ACID WITH A BASE TITRATION OF AN ACID WITH A BASE 1 NOTE: You are required to view the podcast entitled Use of Burets for Titrations before coming to lab this week. To view the podcast, consisting of eight episodes, go

More information

CHEM 30A EXPERIMENT 8 & 9: ACID- BASE TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to:

CHEM 30A EXPERIMENT 8 & 9: ACID- BASE TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to: 1 Learning Outcomes CHEM 30A EXPERIMENT 8 & 9: ACID- BASE TITRATION Upon completion of this lab, the student will be able to: 1) Prepare a solution of primary standard 2) Determine the molar concentration

More information

# 12 ph-titration of Strong Acids with Strong Bases

# 12 ph-titration of Strong Acids with Strong Bases # 12 ph-titration of Strong Acids with Strong Bases Purpose: A strong acid solution is titrated with a strong base solution. A titration curve is then used to determine the endpoint and find the concentration

More information

Experiment 20-Acid-Base Titration: Standardization of KOH and Determination of the Molarity and/or Percent Composition of an Acid Solution

Experiment 20-Acid-Base Titration: Standardization of KOH and Determination of the Molarity and/or Percent Composition of an Acid Solution Experiment 20-Acid-Base Titration: Standardization of KOH and Determination of the Molarity and/or Percent Composition of an Acid Solution In this experiment, you will determine the molarity and percent

More information

In this laboratory exercise we will determine the percentage Acetic Acid (CH 3 CO 2 H) in Vinegar.

In this laboratory exercise we will determine the percentage Acetic Acid (CH 3 CO 2 H) in Vinegar. The titration of Acetic Acid in Vinegar In this laboratory exercise we will determine the percentage Acetic Acid (CH CO H) in Vinegar. We will do this by Titrating the Acetic Acid present with a Strong

More information

H 3 O + (aq) + P 2- (aq)

H 3 O + (aq) + P 2- (aq) PURPOSE: To standardize a solution of sodium hydroxide by titration with a primary standard, (KHC 8 H 4 O 4 ), potassium hydrogen phthalate (KHC 8 H 4 O 4 ) PRINCIPLES: Most shelf reagents, such as 0.10

More information

Titration of Vinegar

Titration of Vinegar EXPERIMENT 8 Prepared by Edward L. Brown, Lee University and Verrill M. Norwood, Cleveland State Community Collee The student will become familiar with the techniques of titration and expressin a solution

More information

The Thermodynamics of the Solubility of Borax

The Thermodynamics of the Solubility of Borax Experiment 10 Pre-Lab Assignment Before coming to lab: Read the lab thoroughly. Answer the pre-lab questions that appear at the end of this lab exercise. The questions should be answered on a separate

More information

ph Measurement and its Applications

ph Measurement and its Applications ph Measurement and its Applications Objectives: To measure the ph of various solutions using indicators and ph meters. To perform a ph titration. To create and study buffer solutions. To determine the

More information

EXPERIMENT 12B: TITRATION OF AN UNKNOWN ACID INTRODUCTION

EXPERIMENT 12B: TITRATION OF AN UNKNOWN ACID INTRODUCTION EXPERIMENT 12B: TITRATION OF AN UNKNOWN ACID INTRODUCTION In this experiment you will determine the molar mass of an unknown acid by titration with the sodium hydroxide you prepared and standardized in

More information

EXPERIMENT A7: VINEGAR TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to:

EXPERIMENT A7: VINEGAR TITRATION. Learning Outcomes. Introduction. Upon completion of this lab, the student will be able to: 1 Learning Outcomes EXPERIMENT A7: VINEGAR TITRATION Upon completion of this lab, the student will be able to: 1) Prepare a solution of primary standard 2) Determine the molar concentration of a solution

More information

Experiment 10 Acid-Base Titrimetry. Objectives

Experiment 10 Acid-Base Titrimetry. Objectives Experiment 10 Acid-Base Titrimetry Objectives 1. To standardize an acid, HCl, solution. 2. To determine the concentration of an unknown Na 2 CO 3, sodium carbonate solution. Introduction Alkaline conditions

More information

8 Titration of Acids and bases

8 Titration of Acids and bases 8 Titration of Acids and bases Name: Date: Section: Objectives Reinforce acid-base chemistry principles from chapter 4 in Silberberg Standardize a sodium hydroxide solution Determine the molarity of an

More information

Thermodynamics and the Solubility of Sodium Tetraborate Decahydrate

Thermodynamics and the Solubility of Sodium Tetraborate Decahydrate Thermodynamics and the Solubility of Sodium Tetraborate Decahydrate In this experiment you, as a class, will determine the solubility of sodium tetraborate decahydrate (Na 2 B 4 O 7 10 H 2 O or Na 2 [B

More information

TITRATION: STANDARDIZATION OF A BASE AND ANALYSIS OF STOMACH ANTACID TABLETS. Teacher Notes

TITRATION: STANDARDIZATION OF A BASE AND ANALYSIS OF STOMACH ANTACID TABLETS. Teacher Notes TITRATION: STANDARDIZATION OF A BASE AND ANALYSIS OF STOMACH ANTACID TABLETS Teacher Notes This experiment is designed for students working singly or in groups of two. The overall purpose of this experiment

More information

Reaction Stoichiometry

Reaction Stoichiometry Reaction Stoichiometry PURPOSE To determine the stoichiometry of acid-base reactions by measuring temperature changes which accompany them. GOALS To learn to use the MicroLab Interface. To practice generating

More information

Experimental Procedure. Lab 406

Experimental Procedure. Lab 406 Experimental Procedure Lab 406 Overview This experiment is to be complete in cooperation with other chemists/chemist groups in the laboratory. In PART A, a standardized solution of hydrochloric acid is

More information

EXPERIMENT 5 ACID-BASE TITRATION

EXPERIMENT 5 ACID-BASE TITRATION EXPERIMENT 5 ACID-BASE TITRATION INTRODUCTION Much of chemistry and biology is concerned with the behavior of acids and bases. Acids and bases are participants in many reactions in nature, and many reactions

More information

Molarity of Acetic Acid in Vinegar A Titration Experiment

Molarity of Acetic Acid in Vinegar A Titration Experiment Molarity of Acetic Acid in Vinegar A Titration Experiment Introduction Vinegar is prepared commercially in two steps, both requiring microorganisms. The first step is the production of ethyl alcohol, C

More information

Upon completion of this lab, the student will be able to:

Upon completion of this lab, the student will be able to: 1 Learning Outcomes EXPERIMENT 30A7: VINEGAR TITRATION Upon completion of this lab, the student will be able to: 1) Measure the amount of acetic acid in a solution of vinegar Introduction The molar concentration

More information

Learn to do quantitative titration reactions. Observe the mole ratios of several simple chemical reactions.

Learn to do quantitative titration reactions. Observe the mole ratios of several simple chemical reactions. CHAPTER 6 Stoichiometry of Reactions in Solution Objectives The objectives of this laboratory are to: Learn to do quantitative titration reactions. Observe the mole ratios of several simple chemical reactions.

More information

Chemistry 1B Experiment 17 89

Chemistry 1B Experiment 17 89 Chemistry 1B Experiment 17 89 17 Thermodynamics of Borax Solubility Introduction In this experiment, you will determine the values of H and S for the reaction which occurs when borax (sodium tetraborate

More information

CHM 130 Acid-Base Titration Molarity of Acetic Acid in Vinegar

CHM 130 Acid-Base Titration Molarity of Acetic Acid in Vinegar CHM 130 Acid-Base Titration Molarity of Acetic Acid in Vinegar INTRODUCTION One of the most important techniques for chemical analysis is titration to an equivalence point. To illustrate this procedure,

More information

DETERMINATION OF THE SOLUBILITY PRODUCT OF GROUPII HYDROXIDES

DETERMINATION OF THE SOLUBILITY PRODUCT OF GROUPII HYDROXIDES INTRODUCTION DETERMINATION OF THE SOLUBILITY PRODUCT OF GROUPII HYDROXIDES SOLUBILTY EQUILIBRIA Many systems in chemistry appear to be static when in fact they are in (dynamic) equilibrium. When a system

More information

Figure 1. Oxygen. (g) +... (g)... SO 3. The pressure of the reacting gases was increased.

Figure 1. Oxygen. (g) +... (g)... SO 3. The pressure of the reacting gases was increased. Q1. Figure 1 represents a reaction in the production of sulfuric acid. Figure 1 Oxygen Sulfur dioxide Sulfur trioxide (a) Complete and balance the equation for the reaction.... SO 2 (g) +... (g)... SO

More information

Acid-Base Titration Acetic Acid Content of Vinegar

Acid-Base Titration Acetic Acid Content of Vinegar Acid-Base Titration Acetic Acid Content of Vinegar Prelab Assignment Read the entire lab. Write an objective and any hazards associated with this lab in your laboratory notebook. On a separate sheet of

More information

$ % K st. K D [ I 2 ] Aqueous. [ I 2 ] Hexane. % Aqueous

$ % K st. K D [ I 2 ] Aqueous. [ I 2 ] Hexane. % Aqueous Determination of the Stability Constant of the Tri- Iodide Ion by Solvent Extraction Introduction Molecular iodine reacts with iodide to form a complex, called the tri- iodide ion, according to the reaction:

More information

Aqueous Chemical Reactions

Aqueous Chemical Reactions Aqueous Chemical Reactions Introduction Many chemical reactions occur in water and therefore they are considered aqueous chemical reactions. The reagents are typically dissolved or diluted in water and

More information

Acid-Base Titration Curves Using a ph Meter

Acid-Base Titration Curves Using a ph Meter Acid-Base Titration Curves Using a ph Meter Introduction: In this experiment you will use a ph sensor to collect volume and ph data as you titrate two acids with sodium hydroxide. You will obtain titration

More information

6 Acid Base Titration

6 Acid Base Titration E x p e r i m e n t Acid Base Titration Experiment : http://genchemlab.wordpress.com/-titration/ objectives To understand the concept of titration. To explain the difference between the analyte and standard

More information

Chemistry with Mr. Faucher. Acid-Base Titration

Chemistry with Mr. Faucher. Acid-Base Titration Chemistry with Mr. Faucher Name Date Acid-Base Titration 24 A titration is a process used to determine the volume of a solution needed to react with a given amount of another substance. In this experiment,

More information

Name Period Date. Lab 9: Analysis of Commercial Bleach

Name Period Date. Lab 9: Analysis of Commercial Bleach Name Period Date Lab 9: Analysis of Commercial Bleach Introduction Many common products are effective because they contain oxidizing agents. Some products, which contain oxidizing agents, are bleaches,

More information

When dealing with solids that one can weigh on a balance, determining the number of moles in a particular sample is simply:

When dealing with solids that one can weigh on a balance, determining the number of moles in a particular sample is simply: Experiment 2 Stoichiometry Solids and Solutions Determining the Molarity of a Solution Lab Owl Announcement: Upon completion of this lab, log onto OWL. A Lab Owl section should now appear in your courses

More information

Aqueous Chemical Reactions

Aqueous Chemical Reactions Aqueous Chemical Reactions Introduction Many chemical reactions occur in water and therefore they are considered aqueous chemical reactions. The reagents are typically dissolved or diluted in water and

More information

Chemistry 101 Experiment 12B-ANALYSIS OF COMMERCIAL VINEGARS

Chemistry 101 Experiment 12B-ANALYSIS OF COMMERCIAL VINEGARS Vinegar is a solution of acetic acid (HC2H3O2). The strength or concentration of the vinegar is usually given on the label of the bottle in percent by weight or percent acidity. The United States Food

More information

Acid-Base Titration Curves Using a ph Meter

Acid-Base Titration Curves Using a ph Meter Acid-Base Titration Curves Using a ph Meter Introduction: In this experiment you will use a ph sensor to collect volume and ph data as you titrate two acids with sodium hydroxide. You will obtain titration

More information

Acid-Base Titration. M M V a

Acid-Base Titration. M M V a Acid-Base Titration Pre-Lab Discussion In the chemistry laboratory, it is sometimes necessary to experimentally determine the concentration of an acid solution or a base solution. A procedure for making

More information

Titration with an Acid and a Base

Titration with an Acid and a Base Skills Practice Titration with an Acid and a Base Titration is a process in which you determine the concentration of a solution by measuring what volume of that solution is needed to react completely with

More information

Partner: Judy 29 March Analysis of a Commercial Bleach

Partner: Judy 29 March Analysis of a Commercial Bleach Partner: Judy 29 March 2012 Analysis of a Commercial Bleach Purpose: The purpose of this lab is to determine the amount of sodium hypochlorite (NaClO) in commercial bleach. This can be done by forming

More information

GETTING THE END POINT TO APPROXIMATE. Two hours

GETTING THE END POINT TO APPROXIMATE. Two hours Chem 1312 Handout Experiment ONE Laboratory Time Required Special Equipment and Supplies Objective Safety First Aid GETTING THE END POINT TO APPROXIMATE THE EQUIVALENCE POINT Two hours Balance Potassium

More information

Pre-lab: Read sections 10.6 in the textbook. Complete the attached pre-lab by Thursday, May 22.

Pre-lab: Read sections 10.6 in the textbook. Complete the attached pre-lab by Thursday, May 22. Lab 5: Titration of an unknown acid Objective: Determine the concentration of an unknown monoprotic acid by titration, the process that matches the number of moles of base with the number of moles of acid.

More information

Objectives To prepare a dilute solution of a weak acid. To prepare a buffer of a specific ph value.

Objectives To prepare a dilute solution of a weak acid. To prepare a buffer of a specific ph value. E x p e r i m e n t Chemistry Is phun! Objectives To prepare a dilute solution of a weak acid. To prepare a buffer of a specific ph value. To observe the effects of adding acid and base to a buffer solution.

More information

2002 D Required 2001 D Required

2002 D Required 2001 D Required 2002 D Required A student is asked to determine the molar enthalpy of neutralization, H neut, for the reaction represented above. The student combines equal volumes of 1.0 M HCl and 1.0 M NaOH in an open

More information

Read the lab thoroughly. Answer the pre-lab questions that appear at the end of this lab exercise.

Read the lab thoroughly. Answer the pre-lab questions that appear at the end of this lab exercise. Experiment 10 Stoichiometry- Gravimetric Analysis Pre-lab Assignment Read the lab thoroughly. Answer the pre-lab questions that appear at the end of this lab exercise. Purpose The purpose this experiment

More information

PreLAD: b. KHP is a monoprotic acid, what are the number of moles of ionizable H + in the approximately 0.25 g of KHP?

PreLAD: b. KHP is a monoprotic acid, what are the number of moles of ionizable H + in the approximately 0.25 g of KHP? LAD G.1 (pg! 1 of 6! ) What % of vinegar is really acetic acid? Name Per What part of the solution is really HC2H3O2 aka CH3COOH? What is the Ka of acetic acid? Introduction: The acid in vinegar is acetic

More information

Determination of the K a Value and Molar Mass of an Unknown Weak Acid

Determination of the K a Value and Molar Mass of an Unknown Weak Acid 10 Determination of the K a Value and Molar Mass of an Unknown Weak Acid Introduction In this experiment you will titrate a monoprotic weak acid with a strong base, and measure the titration curve with

More information

CHEM Practice to be done before the lab. Experiment 9 Introduction to Volumetric Techniques II. Objectives

CHEM Practice to be done before the lab. Experiment 9 Introduction to Volumetric Techniques II. Objectives 1 CHEM 0011 Experiment 9 Introduction to Volumetric Techniques II Objectives 1. To learn the proper technique to use a burette. 2. To learn the proper technique to carry out a titration. 3. To verify the

More information

Solubility of KHT and Common ion Effect

Solubility of KHT and Common ion Effect Solubility of KHT and Common ion Effect v010516 You are encouraged to carefully read the following sections in Tro (3 rd ed.) to prepare for this experiment: Sec 16.5, pp 783-788 (Solubility Equilibria

More information

By contrast, solubility equilibrium reactions are written from the perspective of the solid reactant dissolving into ions

By contrast, solubility equilibrium reactions are written from the perspective of the solid reactant dissolving into ions LAD F.2 (pg 1 of 8) Ksp Solubility Product for Calcium Hydroxide Name Per Introduction Most solubility equilibrium investigated in this course involve ionic compounds as opposed to molecular compounds.

More information

PURPOSE: To determine the Rate Law for the following chemical reaction:

PURPOSE: To determine the Rate Law for the following chemical reaction: PURPOSE: To determine the Rate Law for the following chemical reaction: H 2 O 2 (aq) + 2 I - (aq) + 2 H 3 O + (aq) 4 H 2 O(l) + I 2 (aq) Hydrogen Iodide Hydronium Water Iodine Peroxide Ion Ion PRINCIPLES:

More information

Synthesis and Analysis of a Coordination Compound

Synthesis and Analysis of a Coordination Compound Synthesis and Analysis of a Coordination Compound In addition to forming salts with anions, transition metal cations can also associate with neutral molecules (and ions) through a process called ligation.

More information

Section 10.3: Acid Base Stoichiometry

Section 10.3: Acid Base Stoichiometry Section 10.3: Acid Base Stoichiometry Tutorial 1 Questions, page 481 1. It is necessary to keep the volume of indicator used to a minimum because many acid base indicators are weak acids. Some of the base

More information

Acidity of Beverages Lab

Acidity of Beverages Lab Acidity of Beverages Lab Name: Introduction: Common beverages may be either acidic or basic. Fruit juices, for example, get their sweet taste from sugars and their sour or tart taste from weak acids such

More information

Chemistry 11 Unit 1:Stoichiometry 10/30/2016 /20

Chemistry 11 Unit 1:Stoichiometry 10/30/2016 /20 Lab #6 Reaction of a Metal with Hydrochloric Acid THE AIM OF THIS EXPERIMENT: Name: Partners: In this experiment, you will react hydrochloric acid with magnesium to produce H 2 gas, and to determine the

More information

POGIL LAB EXERCISE 15 HOW DO YOU STANDARDIZE AN ACID AND BASE?

POGIL LAB EXERCISE 15 HOW DO YOU STANDARDIZE AN ACID AND BASE? POGIL LAB EXERCISE 15 HOW DO YOU STANDARDIZE AN ACID AND BASE? POGIL LAB 15 Page 1 of 10 Each member should assume his or her role at this time. The new manager takes charge of the POGIL folder and hands

More information

Experiment 5 Titration of Acids and Bases

Experiment 5 Titration of Acids and Bases CEAC 103 GENERAL CHEMISTRY Experiment 5 Titration of Acids and Bases Purpose: To become familiar with the techniques of titration, a volumetric method of analysis; to determine the molarity and ph of an

More information

1. Base your answer to the following question on information below and on your knowledge of chemistry.

1. Base your answer to the following question on information below and on your knowledge of chemistry. 1. Base your answer to the following question on information below and on your knowledge of A sample of nitric acid contains both ions and ions. This sample has a ph value of 1. Write a name of the positive

More information

Aqueous Chemical Reactions

Aqueous Chemical Reactions Aqueous Chemical Reactions Introduction Many chemical reactions occur in water and therefore they are considered aqueous chemical reactions. The reagents are typically dissolved or diluted in water and

More information