VOCs Emissions and Structural Changes of Polypropylene During Multiple Melt Processing

Size: px
Start display at page:

Download "VOCs Emissions and Structural Changes of Polypropylene During Multiple Melt Processing"

Transcription

1 VOCs Emissions and Structural Changes of Polypropylene During Multiple Melt Processing Q. Xiang, M. Xanthos*, S. Mitra and S. H. Patel* Department of Chemical Engineering, Chemistry and Environmental Science *Also: Polymer Processing Institute, GITC Building, Suite 3901 New Jersey Institute of Technology, Newark, NJ Abstract Polypropylene, as a commodity recyclable thermoplastic, is studied in this research to evaluate the potential environmental impact resulting from volatile organic compounds (VOCs) emitted during multiple reprocessing. Unstabilized commercial polypropylene (PP) grade was processed several times by injection molding. Samples were examined after each cycle for total VOCs emissions with a flame ionization detector (FID) and cumulative VOCs emissions were obtained after each processing step. Corresponding structural changes were investigated with Fourier Transform Infrared (FTIR) Spectroscopy and results were correlated with rheological data that showed decreasing viscosity particularly after the 7 th processing cycle. Introduction Polypropylene is widely used in commodity as well as engineering applications, particularly when reinforced. Due to its high production volume, it is recycled for both economic and environmental purposes. For instance, PP scrap from molding operations can be mixed with virgin material at appropriate ratios, and then remolded into new parts. From an environmental point of view, with the increasing cost of landfill space and the growing concern about waste materials, an increasing number of techniques for recycling and reusing waste PP and other plastic products have been developed (1). With respect to recycling/reuse, a number of potential environmental problems related to emissions have been of concern to the Environmental Protection Agency (EPA) and the Occupation Safety and Health Administration (OSHA). Among the emissions which can be as high as 5% of the actual tonnage of resins processed annually in the U.S., (2), volatile organic compounds (VOCs) are receiving much attention. Many of these VOCs are hazardous air pollutants, which can cause serious health problems, and environmental effects such as the formation of smog and ground-level ozone. Therefore, they are regulated by the Clean Air Act Amendments (CAAA) of Title V of this Act also established a permit program for emission sources to ensure an eventual reduction in volatiles (3). As a result of long thermal exposure, oxidative and mechanical degradation and the presence of moisture and contaminants, reprocessing of scrap plastics may generate a significant amount of VOCs emissions. These degradation mechanisms may also result in structural changes with concomitant effects on properties. For PP, there exists a number of reports on chain scission and the corresponding changes in molecular weight, structure and mechanical properties as a result of degradation due to multiple melt reprocessing of stabilized or unstabilized grades (1,4-6). However, no work has been published to our knowledge on the effect of multiple melt reprocessing on the VOCs emissions from polymers. This research examines the total VOCs emissions generated from PP processed several times by injection molding. The measurement of total VOCs was carried out with an analytical system based on the non-isothermal heating of the polymer followed by a direct analysis with a FID (flame ionization detector). Since FID does not respond to H 2 O, CO and CO 2, this method gives a more accurate measure of VOCs emitted from polymers. Consequently, this method can measure the true harmful environmental impact level from polymer recycling. Another advantage of this system, based on its very low detection limit for organics, is its higher sensitivity versus traditional thermal analysis techniques such as TGA and DSC. The variations in the total VOCs were compared for PP s processed several times, while the changes in chemical structure were analyzed with FTIR and correlated with rheological data. Materials Experimental Commercial grade unstabilized polypropylene (Profax 6501, Montell) was injection molded up to cycles in a Toyo Ti-90G injection molder. Experimental conditions were: barrel temperature profile o C, nozzle

2 temperature 240 o C and mold temperature 25 o C. The 1 st cycle was carried out with the virgin powder polymer and the remaining 9 cycles with granules produced by grinding ASTM specimens obtained in the subsequent injection molding steps to less than 20 mesh size. Total VOCs emissions were measured on the virgin resin and materials obtained from a select number of reprocessing cycles. Total VOCs measurement A schematic diagram of the analytical system is shown in Fig. 1. The reactor is about 5"(length) x 1/4" (O. D.) stainless steel tubing blocked with glass fiber on both ends. About 2.5 mg of PP sample was placed in the reactor. After the system reached a steady state, with a flow of N 2 (carrier gas, ~30ml/min), the reactor was heated in a temperature-controlled oven from 36 o C to 180 o C, at a fixed ramp rate of 40 o C/min. To estimate the possible maximum amount of total VOCs, the sample was kept at the final temperature for an additional three minutes period. The VOCs emissions were measured with the FID as evolution profiles whose area could be determined by integrating at different time periods. Since this area is proportional to the amount of VOCs emitted from the polymer sample, it was calibrated with standard propane gas to calculate the total amount of VOCs emitted as a function of time. FTIR analysis Polypropylene films from each cycle were prepared by compression molding at 2 o C and 2268 kg (5,000 lb.) force. The thickness of the films ranged from 0 to 125 µm. A Perkin Elmer Spectrum One FT-IR Spectrometer was used to obtain the IR spectra of the films in the range of cm -1, with a resolution of 4 cm -1 and averaging 25 scans. Melt Flow Index (MFI) MFI was measured in a Tinius Olsen Extrusion Plastometer under standard PP conditions (2.16 kg, 230 o C) on samples containing additional antioxidant to prevent further degradation. Results and Discussion VOCs emissions from multiple processed PP Fig. 2(a) shows the thermally generated VOCs emissions from PP samples, selected among the virgin resin (0), 1 st, 3 rd, 4 th, 6 th, 8 th and th processing cycle. The two sets of data including averages of 3-6 determinations and standard deviations represent the emissions obtained when the sample was heated from 36 o C to 180 o C at a rate of 40 o C/min, and those emanated after the sample was held at 180 o C for three additional minutes. For both sets of data, and within the standard deviation range, the average value of total emissions does not appear to vary significantly among cycles. Standard deviations appear to increase after the first two cycles, (0 and 1), with the highest values shown for the th cycle. This may be attributed to equipment contamination that occurred during the time intervals between the multiple reprocessing and grinding steps of the samples produced in this work. The trends shown in Fig. 2(a) are not unexpected, since the data obtained here correspond to the possible maximum amount of VOCs generated under our particular experimental conditions. These values may not be equal to the VOCs amounts emitted during each processing cycle and lost in the atmosphere, or partly retained in the reprocessed granules. In addition, our experimental heating times, (in the absence of shear), are different from the residence times in the injection molder, (under shear). For example, it took 3.6 min to heat the sample from 36 o C to 180 o C at 40 o C/min, whereas in real processing, heating rate was higher, heating time shorter and processing temperature higher (240 o C). Experiments are under way to simulate more accurately times and temperatures between our static experiments and the actual processing conditions. Correlation between the VOCs emissions and the rheological data Fig. 2(b) presents the cumulative VOCs emissions as a function of processing cycle based on the subtotal of all the previous cycles. As the data in Fig. 2(a) represent the possible maximum amount of VOCs independent of the cycle number, Fig. 2(b) shows an increasing tendency of the maximum VOCs with increasing number of cycles. This trend of cumulative maximum VOCs versus number of cycles may be related to a similar trend of Melt Flow Index (MFI) versus number of cycles shown in Fig. 3. With increasing number of cycles, the increase in MFI indicates a decrease in melt viscosity, a corresponding reduction of MW and tendency towards further degradation. Comparison of Fig.2 (b) and Fig. 3 shows that both the cumulative VOCs and extent of degradation increase linearly up to the 6th cycle, and more rapidly thereafter. The enhanced increase of MFI and VOCs after the 7 th cycle is believed to be due to the combination of further degradation, higher contamination and changes in processing conditions, particularly cooling time, required to accommodate materials with increasingly lower melt viscosity. Changes in chemical structure of multiple processed PP Fig. 4(a) shows the FTIR spectra (wavenumber cm -1 ) of films obtained from reprocessed PP. With

3 increasing processing cycle number, the absorption increased in the range between 1800 and 1675 cm -1, which represents the region of carbonyl group (>C=O) absorption. The appearance of carbonyl group indicates that thermal/oxidative degradation took place during multiple injection molding. However, only after the 7 th cycle, oxidative degradation became more prominent as shown by a large increase in the absorption of carbonyl group at the 8 th cycle. This is more evident in Fig. 4(b), where the spectra were processed (subtracted) against that of the 0 cycle, (virgin resin), in order to eliminate the effect of film thickness (sample concentration). This remarkable increase in the concentration of carbonyl group indicates enhanced oxidative degradation, and thus, can be related to the rapid increase in the VOCs and MFI after the 7 th cycle. Fig. 4(b) also illustrates that with increasing number of processing cycle, the dominant carbonyl group absorption shifted to a higher wavenumber. Before the 8 th cycle, the carbonyl group showed a relatively strong absorption at 1722 cm -1 ; then the absorption at 1736cm -1 increased rapidly. Since the bands at cm -1 are assigned to aldehyde and ketone, and those at cm -1 are due to ester group (5), it appears that severe, further thermal/oxidative degradation occurred after the 8 th cycle accompanied by the formation of new functional groups. This is in agreement with the measured MFI and cumulative VOCs data after the 7 th cycle. Conclusions Polypropylene was evaluated for total VOCs emissions generated during multiple melt reprocessing. Results show that the maximum amount of total VOCs from each individual cycle did not significantly change, while the cumulative VOCs increased with increasing processing cycle. After the 7 th cycle, significant changes in chemical structure were observed, accompanied by prominent oxidative degradation shown as a strong FTIR absorption of ester group. The trends on cumulative VOCs emissions and FTIR analysis versus cycle number were in good agreement with changes in the rheological data (MFI). Acknowledgments Financial support for this work was provided by the Multi-Lifecycle Engineering Research Center (MERC) of NJIT, which is partially funded by the New Jersey Commission on Science and Technology (NJCST). Special thanks are due to Mr. J. Guo of PPI/NJIT for the injection molding experiments. Thanks are also due to Dr. V. Tan, Dr. S. Dey and Mr. D. Conti of PPI for the lab assistance. References 1. Guerrica-Echevarria, G., et al, Polym. Degrad. Stab., (1996). 2. Patel, S.H. and M. Xanthos, Adv. Polym. Technol., 14: (1995). 3. Adams, K., et al, J. Air & Waste Mange. Assoc., (1999). 4. Canevarolo, S. V., Chain scission distribution function for polypropylene degradation during multiple extrusions, Polym. Degrad. Stab., in press. 5. Hinsken, H., et al, Polym. Degrad. Stab., (1991). 6. Gonzalez-Gonzalez, V. A., et al, Polym. Degrad. Stab., (1998). Key words Volatile organic compounds (VOCs), emissions, polypropylene, multiple processing, degradation, FTIR spectroscopy N 2 Mass flow Controller Switching Valve Temperature Controlled oven Flame Ionization Detector Calibration standard Mass flow Controller Reactor Sample Computer Data Acquisition Figure 1. Direct FID measurement of the VOCs emissions thermally generated from PP

4 VOCs emissions as weight percentage (%) h e a t e d f r o m 3 6 o C t o o C h e ld a t o C f o r 3 m in n u m b e r o f c y c le Figure 2(a). Effect of multiple injection molding on the VOCs emissions generated from PP when heated from 36 o C to 180 o C at the rate of 40 o C/min Cumulative VOCs emissions (%) h e a t e d f r o m 3 6 o C t o o C h e ld a t o C f o r 3 m in n u m b e r o f c y c le Figure 2(b). Cumulative VOCs emissions as a function of processing cycle

5 40 MFI (g/min) number of cycle Figure 3. Melt flow index (MFI) of PP after multiple injection molding Cycle 0 Cycle %T 7 8 %T cm-1 (a) cm-1 (b) Figure 4 (a). FTIR spectra of unstabilized PP after different injection molding cycles (b). Comparison of the carbonyl group after different injection molding cycles

Title: Cesa-extend a User Friendly Technology to Enhance Reprocessing and Recycling of Condensation Plastics

Title: Cesa-extend a User Friendly Technology to Enhance Reprocessing and Recycling of Condensation Plastics GPEC 24 Paper Abstract #52: Title: Cesa-extend a User Friendly Technology to Enhance Reprocessing and Recycling of Condensation Plastics Author(s): V. Karayan, Clariant Masterbatches, and M. Villalobos,

More information

SILMALAB is a laboratory of analysis for plastics industry that takes advantage of the experience gained by our engineers in 30 years of work and

SILMALAB is a laboratory of analysis for plastics industry that takes advantage of the experience gained by our engineers in 30 years of work and SILMALAB is a laboratory of analysis for plastics industry that takes advantage of the experience gained by our engineers in 30 years of work and provides application s interpretations of the results of

More information

Atmospheric Analysis Gases. Sampling and analysis of gaseous compounds

Atmospheric Analysis Gases. Sampling and analysis of gaseous compounds Atmospheric Analysis Gases Sampling and analysis of gaseous compounds Introduction - External environment (ambient air) ; global warming, acid rain, introduction of pollutants, etc - Internal environment

More information

Physico-chemical characterization and comparison of fluorinated commercial Ski-Waxes.

Physico-chemical characterization and comparison of fluorinated commercial Ski-Waxes. SKI-WAX 2013. Physico-chemical characterization and comparison of fluorinated commercial Ski-Waxes. Luca Fambri, Riccardo Ceccato, Emanuela Callone and Denis Lorenzi Department of Industrial Engineering,

More information

Infrared Spectroscopy

Infrared Spectroscopy Reminder: These notes are meant to supplement, not replace, the laboratory manual. Infrared Spectroscopy History and Application: Infrared (IR) radiation is simply one segment of the electromagnetic spectrum

More information

Evolved gas analysis by simultaneous thermogravimetric differential thermal analysis-fourier transformation infrared spectroscopy (TG-DTA-FTIR)

Evolved gas analysis by simultaneous thermogravimetric differential thermal analysis-fourier transformation infrared spectroscopy (TG-DTA-FTIR) Technical articles Evolved gas analysis by simultaneous thermogravimetric differential thermal analysis-fourier transformation infrared spectroscopy (TG-DTA-FTIR) Tadashi Arii* 1. Introduction Simultaneous

More information

Introduction to IH Analytical Chemistry

Introduction to IH Analytical Chemistry Introduction to IH Analytical Chemistry Sampling and Analysis Manning, Eide, Van Etten (Apr 2013) Foreword Thank you for purchasing the Introduction to IH Analytical Chemistry self-study workbook. Course

More information

Polymer engineering syllabus (BSc)

Polymer engineering syllabus (BSc) Polymer engineering syllabus (BSc) First semester Math 1 Physics 1 Physics 1 lab General chemistry General chemistry lab workshop Second semester Math 2 Physics 2 Organic chemistry 1 Organic chemistry

More information

Overview of Maleic-Anhydride-Grafted Polyolefin Coupling Agents

Overview of Maleic-Anhydride-Grafted Polyolefin Coupling Agents Overview of Maleic-Anhydride-Grafted Polyolefin Coupling Agents A guide to understanding their uses, benefits, functions, selection, and developments Louis W. Martin, Addcomp North America Inc. Fundamentals

More information

Gas Chromatography (GC)

Gas Chromatography (GC) Gas Chromatography (GC) Ahmad Aqel Ifseisi Assistant Professor of Analytical Chemistry College of Science, Department of Chemistry King Saud University P.O. Box 2455 Riyadh 11541 Saudi Arabia Office: AA53

More information

Technical know-how in thermal analysis measurement

Technical know-how in thermal analysis measurement Technical articles Technical know-how in thermal analysis measurement Evolved gas analysis by thermogravimetry-differential thermal analysis-mass spectrometry (TG-DTA-MS) technique Kazuko Motomura* and

More information

Ch. 9 Atomic Absorption & Atomic Fluorescence Spectrometry

Ch. 9 Atomic Absorption & Atomic Fluorescence Spectrometry Ch. 9 Atomic Absorption & Atomic Fluorescence Spectrometry 9.1 9A. Atomization Most fundamental for both techniques. Typical types 1. flame - burner type 2. Electrothermal graphite furnace 3. Specialized

More information

STANDARD OPERATING PROCEDURES

STANDARD OPERATING PROCEDURES PAGE: 1 of 12 CONTENTS 1.0 SCOPE AND APPLICATION 2.0 METHOD SUMMARY 3.0 SAMPLE PRESERVATION, CONTAINERS, HANDLING, AND STORAGE 4.0 INTERFERENCES AND POTENTIAL PROBLEMS 5.0 EQUIPMENT/APPARATUS 6.0 REAGENTS

More information

How to Use Kinetic Modeling Analysis To Predict Profile Part Failure

How to Use Kinetic Modeling Analysis To Predict Profile Part Failure Tips and Techniques Reprinted From: PLASTICS TECHNOLOGY Magazine How to Use Kinetic Modeling Analysis To Predict Profile Part Failure Real-world project demonstrates how kinetic modeling can help estimate

More information

Alkaline Hydrolysis of Polyethylene Terephthalate at Lower Reaction Temperature

Alkaline Hydrolysis of Polyethylene Terephthalate at Lower Reaction Temperature THE SCIENCE AND ENGINEERING REVIEW OF DOSHISHA UNIVERSITY, VOL. 52, NO. 2 July 2011 Alkaline Hydrolysis of Polyethylene Terephthalate at Lower Reaction Temperature Masakazu YAMASHITA* and Hideyuki MUKAI*

More information

A new geomembrane for chlorinated water containment

A new geomembrane for chlorinated water containment A new geomembrane for chlorinated water containment Erich Rangel 1 *, Andrew Mills 2, David Beaumier 3, and Brian Fraser 4 1. Environmental Containment Division, Layfield Group Ltd., Canada 2. Environmental

More information

Method for Characterization of Gum Rosin by Capillary Gas Chromatography

Method for Characterization of Gum Rosin by Capillary Gas Chromatography PCA TEST METHOD PCTM 27 Published 1/1 2004 1. Scope Method for Characterization of Gum Rosin by Capillary Gas Chromatography 1.1 These test methods cover the determination of the amounts of certain rosin

More information

White Paper. Overview: NDIR Definition:

White Paper. Overview: NDIR Definition: Title: NDIR Technology Overview, Compliance, and Comparison to Other Generally Available Gas Measurement Technologies TSN Number: 06 File:\\MII- SRV1\Metron\Bridge_Analyzers\Customer_Service_Documentation\White_Papers\06

More information

ANALYTICAL METHOD DETERMINATION OF VOLATILE ALDEHYDES IN AMBIENT AIR Page 1 of 11 Air sampling and analysis

ANALYTICAL METHOD DETERMINATION OF VOLATILE ALDEHYDES IN AMBIENT AIR Page 1 of 11 Air sampling and analysis DETERMINATION OF VOLATILE ALDEHYDES IN AMBIENT AIR Page 1 of 11 Replaces: Dated: Author: Date: AM-No.: New New Nils Arne Jentoft 18.06.2014 0 CHANGES This procedure is new. 1 SCOPE This document describes

More information

DEPARTMENT OF ELECTRONICS AND INSTRUMENTATION ENGINEERING SRM NAGAR, KATTANKULATHUR-603203 EI 2302 ANALYTICAL INSTRUMENTS QUESTION BANK UNIT I COLORIMETRY AND SPECTROPHOTOMETRY Part A 1. State Lambert

More information

AN INTEGRATED SYSTEM USING TEMPERATURE BASED SAMPLING FOR POLYMER CHARACTERIZATION

AN INTEGRATED SYSTEM USING TEMPERATURE BASED SAMPLING FOR POLYMER CHARACTERIZATION AN INTEGRATED SYSTEM USING TEMPERATURE BASED SAMPLING FOR POLYMER CHARACTERIZATION Paper # 164-8P Pittsburgh Conference 24 T. Wampler, C. Zawodny, L. Mancini CDS Analytical, Inc 465 Limestone Road, Oxford,

More information

Determination of VOC in Artificial Runway by Multiple Headspace Extraction-GC/MS. Gas Chromatography/ Mass Spectrometry APPLICATION.

Determination of VOC in Artificial Runway by Multiple Headspace Extraction-GC/MS. Gas Chromatography/ Mass Spectrometry APPLICATION. APPLICATION NOTE Gas Chromatography/ Mass Spectrometry Author: Kira. Yang PerkinElmer, Inc. Shanghai, China Determination of VOC in Artificial Runway by Multiple Headspace Extraction-GC/MS Introduction

More information

Recycling of bio-based polyamides and polycarbonates

Recycling of bio-based polyamides and polycarbonates Recycling of bio-based polyamides and polycarbonates Peter Sommer-Larsen, Danish Technological Institute, Plastics and Packaging Technology, psl@dti.dk Recycling potential for three biopolymers Study performed

More information

Multiple mechanisms can attack polymer chains here s what can go wrong. By Jeffrey Jansen the Madison group, Madison, Wisconsin, Usa

Multiple mechanisms can attack polymer chains here s what can go wrong. By Jeffrey Jansen the Madison group, Madison, Wisconsin, Usa CONSULTANT S CORNER Plastic Failure Through Molecular Degradation Multiple mechanisms can attack polymer chains here s what can go wrong By Jeffrey Jansen the Madison group, Madison, Wisconsin, Usa [Note:

More information

THEORETICAL DETERMINATION OF THE SAMPLING RATES OF DIFFUSION SAMPLERS FOR VOCS AND ALDEHYDES

THEORETICAL DETERMINATION OF THE SAMPLING RATES OF DIFFUSION SAMPLERS FOR VOCS AND ALDEHYDES THEORETICAL DETERMINATION OF THE SAMPLING RATES OF DIFFUSION SAMPLERS FOR VOCS AND ALDEHYDES J Kouzaki 1*, S Sato 1, S Nakai 1, Y Shirasuna 2, K Hirano 2 1 Graduate School of Environmental and Information

More information

HexPly F655 Resin Systems for Advanced Composites

HexPly F655 Resin Systems for Advanced Composites HexPly F655 Resin Systems for Advanced Composites Product Data Description HexPly F655 is a bismaleimide resin that cures via an addition reaction in a toughened two-phase thermoset matrix with no condensation

More information

Change in physico-mechanical and thermal properties of polyamide / silica nanocomposite film

Change in physico-mechanical and thermal properties of polyamide / silica nanocomposite film International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 7, Issue 6 (June 2013), PP. 01-05 Change in physico-mechanical and thermal properties

More information

Chemistry Instrumental Analysis Lecture 27. Chem 4631

Chemistry Instrumental Analysis Lecture 27. Chem 4631 Chemistry 4631 Instrumental Analysis Lecture 27 Gas Chromatography Introduction GC covers all chromatographic methods in which the mobile phase is gas. It may involve either a solid stationary phase (GSC)

More information

The Influence of Processing-History on the Main Melting Temperature and Secondary Melting Temperature Using DSC. Stephen Sansoterra

The Influence of Processing-History on the Main Melting Temperature and Secondary Melting Temperature Using DSC. Stephen Sansoterra The Influence of Processing-History on the Main Melting Temperature and Secondary Melting Temperature Using DSC Abstract: Stephen Sansoterra Canfield High School, 100 Cardinal Drive, Canfield Ohio Polymers

More information

Gas Chromatography. Introduction

Gas Chromatography. Introduction Gas Chromatography Introduction 1.) Gas Chromatography Mobile phase (carrier gas) is a gas - Usually N 2, He, Ar and maybe H 2 - Mobile phase in liquid chromatography is a liquid Requires analyte to be

More information

Determination of Total Volatile Organic Compounds in Indoor Air Using Agilent 7667A mini TD and 7820A GC

Determination of Total Volatile Organic Compounds in Indoor Air Using Agilent 7667A mini TD and 7820A GC Determination of Total Volatile Organic Compounds in Indoor Air Using Agilent 77A mini TD and 70A GC Application Note Environmental Authors Tingting Bu, Xiaohua Li Agilent Technologies (Shanghai) Co.,

More information

IRRADIATION EFFECTS ON POLY (VINYL CHLORIDE)

IRRADIATION EFFECTS ON POLY (VINYL CHLORIDE) IRRADIATION EFFECTS ON POLY (VINYL CHLORIDE) L.COSTA, V. BRUNELLA, P. BRACCO Dipartimento di Chimica IFM, Università di Torino, Italy E-mail: brunella@ch.unito.it We have studied the electron beam effects

More information

Colombo, Sri Lanka) 3 (Department of Chemistry / University of Sri Jayewardenepura, Sri Lanka) (1)

Colombo, Sri Lanka) 3 (Department of Chemistry / University of Sri Jayewardenepura, Sri Lanka) (1) International Refereed Journal of Engineering and Science (IRJES) ISSN (Online) 2319-183X, (Print) 2319-1821 Volume 2, Issue 4(April 2013), PP.11-16 Mechanical Properties And Kinetics Of Weight Loss Of

More information

Experiment #9. Atomic Emission Spectroscopy

Experiment #9. Atomic Emission Spectroscopy Introduction Experiment #9. Atomic Emission Spectroscopy Spectroscopy is the study of the interaction of light with matter. This interaction can be in the form of the absorption or the emission of electromagnetic

More information

Application Note 032

Application Note 032 Application Note 3 Analysis of Sulfur Compounds Using On-line and Off line TD GC Application Note Abstract This application note shows how Markes TD technology is compatible with trace level sulfur compounds,

More information

Luminescence transitions. Fluorescence spectroscopy

Luminescence transitions. Fluorescence spectroscopy Luminescence transitions Fluorescence spectroscopy Advantages: High sensitivity (single molecule detection!) Measuring increment in signal against a dark (zero) background Emission is proportional to excitation

More information

Scheme 1: Reaction scheme for the synthesis of p(an-co-mma) copolymer

Scheme 1: Reaction scheme for the synthesis of p(an-co-mma) copolymer Electronic Supplementary Material (ESI) for RSC Advances. This journal is The Royal Society of Chemistry 2016 Design and Development of Poly (acrylonitrile-co-methyl methacrylate) Copolymer to Improve

More information

DSC AND TG/DTA AS PROBLEM-SOLVING TOOLS: CHARACTERIZATION OF PHARMACEUTICAL COMPOUNDS

DSC AND TG/DTA AS PROBLEM-SOLVING TOOLS: CHARACTERIZATION OF PHARMACEUTICAL COMPOUNDS DSC AND TG/DTA AS PROBLEM-SOLVING TOOLS: CHARACTERIZATION OF PHARMACEUTICAL COMPOUNDS Problem A scientist working for a major pharmaceutical R&D center is having difficulties in interpreting the DSC results

More information

HYPHENATED TECHNOLOGY GUIDE

HYPHENATED TECHNOLOGY GUIDE HYPHENATED TECHNOLOGY GUIDE TABLE OF CONTENTS TG-IR...3 Hiden Analytical MS Systems for TG-MS...4 TG-MS...5 TG-GC/MS...6 TG-IR-GC/MS...8 HYPHENATED TECHNOLOGY GUIDE Coupling, or hyphenating, two instruments

More information

Intertek Environmental VOC Emissions

Intertek Environmental VOC Emissions 4700 Broadmoor SE, Suite 200 Kentwood, MI 49512 Jesse.ondersma@intertek.com Telephone: 616-656-7401 Facsimile: 616-656-2022 www.intertek.com ELIZABETH FATIMA DO NASCIMENTO AIME P.O.: N.A. Page 1 of 8 Intertek

More information

Chapter 27: Gas Chromatography

Chapter 27: Gas Chromatography Chapter 27: Gas Chromatography Gas Chromatography Mobile phase (carrier gas): gas (He, N 2, H 2 ) - do not interact with analytes - only transport the analyte through the column Analyte: volatile liquid

More information

METHOD 8030A ACROLEIN AND ACRYLONITRILE BY GAS CHROMATOGRAPHY

METHOD 8030A ACROLEIN AND ACRYLONITRILE BY GAS CHROMATOGRAPHY METHOD 8030A ACROLEIN AND ACRYLONITRILE BY GAS CHROMATOGRAPHY 1.0 SCOPE AND APPLICATION 1.1 Method 8030 is used to determine the concentration of the following volatile organic compounds: Compound Name

More information

Supporting Information. High Selectivity of Supported Ru Catalysts in the Selective. CO Methanation - Water Makes the Difference

Supporting Information. High Selectivity of Supported Ru Catalysts in the Selective. CO Methanation - Water Makes the Difference S1 Supporting Information High Selectivity of Supported Ru Catalysts in the Selective CO Methanation - Water Makes the Difference Ali M. Abdel-Mageed,, Stephan Eckle, and R. Ju rgen Behm *, Institute of

More information

THE USE OF ESTERIFIED LIGNIN FOR SYNTHESIS OF DURABLE COMPOSITES

THE USE OF ESTERIFIED LIGNIN FOR SYNTHESIS OF DURABLE COMPOSITES THE USE OF ESTERIFIED LIGNIN FOR SYNTHESIS OF DURABLE COMPOSITES Olsson, S., 1 Östmark, E., 1,2, Ibach, R.E., 3 Clemons, C.M., 3 Segerholm, K.B., 1, 4 & Englund, F. 1 ABSTRACT Lignin is a natural polymer

More information

FTIR Spectrometer. Basic Theory of Infrared Spectrometer. FTIR Spectrometer. FTIR Accessories

FTIR Spectrometer. Basic Theory of Infrared Spectrometer. FTIR Spectrometer. FTIR Accessories FTIR Spectrometer Basic Theory of Infrared Spectrometer FTIR Spectrometer FTIR Accessories What is Infrared? Infrared radiation lies between the visible and microwave portions of the electromagnetic spectrum.

More information

STUDY OF RHEOLOGICAL BEHAVIOR OF REPROCESSING HIGH IMPACT POLYSTYRENE

STUDY OF RHEOLOGICAL BEHAVIOR OF REPROCESSING HIGH IMPACT POLYSTYRENE STUDY OF RHEOLOGICAL BEHAVIOR OF REPROCESSING HIGH IMPACT POLYSTYRENE Peydró M.A. 1, Juárez D., Selles M.A., Sánchez-Caballero S., Pla-Ferrando R. 1 Instituto de Tecnología de Materiales, Universidad Politécnica

More information

Polymer Chemistry Research Experience. Support: NSF Polymer Program NSF (PI: Chang Ryu)/RPI Polymer Center

Polymer Chemistry Research Experience. Support: NSF Polymer Program NSF (PI: Chang Ryu)/RPI Polymer Center Polymer Chemistry Research Experience. Support: NSF Polymer Program NSF-1308617 (PI: Chang Ryu)/RPI Polymer Center Student Name: Michael Hyams Student Affiliation (City, State): Mamaroneck, NY Picture

More information

Industrial Hygiene: Assessment and Control of the Occupational Environment

Industrial Hygiene: Assessment and Control of the Occupational Environment Industrial Hygiene: Assessment and Control of the Occupational Environment Main Topics Air Pollution Control Analytical Methods Ergonomics Gas and Vapour Sampling General Practice Heat and Cold Stress

More information

Analytical Testing Services Commercial Price List ManTech International Corporation January 2018

Analytical Testing Services Commercial Price List ManTech International Corporation January 2018 Analytical ing Services Commercial List ManTech International Corporation January 2018 TABLE OF CONTENTS MECHANICAL TENSILE TESTING... 1 DIFFERENTIAL SCANNING CALORIMETRY (DSC)... 2 THERMOMECHANICAL ANALYSIS

More information

Characterization. Chapter 3: Photo-oxidative degradation in Nylon 66 : Chemical. 3.1 Introduction

Characterization. Chapter 3: Photo-oxidative degradation in Nylon 66 : Chemical. 3.1 Introduction Chapter 3: Photo-oxidative degradation in Nylon 66 : Chemical Characterization 3.1 Introduction Aliphatic polyamides have got very good applications as engineering plastic as well as fiber material. During

More information

Experimental Study on FT-IR Analysis of Chemical Species from Wooden Materials in Pre-combustion Condition

Experimental Study on FT-IR Analysis of Chemical Species from Wooden Materials in Pre-combustion Condition Experimental Study on FT-IR Analysis of Chemical Species from Wooden Materials in Pre-combustion Condition Osami Sugawa, Kyoko Kamiya Department of Mechanical Engineering, Tokyo University of Science,

More information

Thermal Methods of Analysis

Thermal Methods of Analysis Thermal Methods of Analysis Calorie-something we know What is calorie? Can you see or touch a calorie? How is it measured? Working out in gym Change in weight Loss of calories-burning of fat? (10 km=500calories/9cal

More information

EFFECTS OF MOLECULAR STRUCTURE ON MACROSCOPIC MECHANICAL PROPERTIES OF AN ADVANCED POLYMER (LARC -SI)

EFFECTS OF MOLECULAR STRUCTURE ON MACROSCOPIC MECHANICAL PROPERTIES OF AN ADVANCED POLYMER (LARC -SI) EFFECTS OF MOLECULAR STRUCTURE ON MACROSCOPIC MECHANICAL PROPERTIES OF AN ADVANCED POLYMER (LARC -SI) Lee M. Nicholson, Jeffrey A. Hinkley, Karen S. Whitley and Thomas S. Gates National Research Council

More information

ABB MEASUREMENT & ANALYTICS DATA SHEET. PGC5000 Temperature programmed gas chromatograph

ABB MEASUREMENT & ANALYTICS DATA SHEET. PGC5000 Temperature programmed gas chromatograph ABB MEASUREMENT & ANALYTICS DATA SHEET PGC5000 Temperature programmed gas chromatograph 2 P G C 5 0 0 0 T E M P E R AT U R E P R O G R A M M E D D S/ P G C 5 0 0 0 T P - E N Measurement & Analytics The

More information

FTIR Spectrum Interpretation of Lubricants with Treatment of Variation Mileage

FTIR Spectrum Interpretation of Lubricants with Treatment of Variation Mileage FTIR Spectrum Interpretation of Lubricants with Treatment of Variation Mileage Diana Julaidy Patty 1* Richard R Lokollo 2 1.Solid State Physics Laboratory-Departmen of Physics University of Pattimura,

More information

All rights reserved, 2011, Century Extrusion. Why simulation? Limited availability and cost of API s

All rights reserved, 2011, Century Extrusion. Why simulation? Limited availability and cost of API s Evonik Industries 4 th International Symposium on Pharmaceutical Melt Extrusion Understanding Melt Extrusion Processes by Simulation Presented by Adam Dreiblatt Director, Process Technology All rights

More information

Electronic Supplementary Information. Enhanced Photocatalytic/photoelectrocatalytic Activities

Electronic Supplementary Information. Enhanced Photocatalytic/photoelectrocatalytic Activities Electronic Supplementary Material (ESI) for CrystEngComm. This journal is The Royal Society of Chemistry 2017 Electronic Supplementary Information Electrospun BiVO 4 Nanobelts with Tailored Structures

More information

Fast Determination of Impurities in Propane- Propylene Streams Using a Pulsed Flame Photometric Detector (PFPD) and a New Capillary.

Fast Determination of Impurities in Propane- Propylene Streams Using a Pulsed Flame Photometric Detector (PFPD) and a New Capillary. Application Note 36720111 Fast Determination of Impurities in Propane- Propylene Streams Using a Pulsed Flame Photometric Detector (PFPD) and a New Capillary PLOT Column Keywords Pulsed Flame Photometric

More information

New ZB-5HT Inferno The World s Highest Temperature Non-Metal GC Column

New ZB-5HT Inferno The World s Highest Temperature Non-Metal GC Column New ZB-5HT Inferno The World s Highest Temperature Non-Metal GC Column The World's First Non-metal 5% Phenyl Phase GC Column Rated to 430 C * Specially processed for thermal stability up to 430 C A true

More information

RS DYNAMICS ECOPROBE 5. Portable IR/PID Gas Analyzer PID. PID and IR Analyzers

RS DYNAMICS ECOPROBE 5. Portable IR/PID Gas Analyzer PID. PID and IR Analyzers RS DYNAMICS ECOPROBE 5 Portable IR/PID Gas Analyzer PID + IR PID and IR Analyzers General ECOPROBE 5 has two autonomous analyzers in one case. The combination of analyzers provides a set of data designed

More information

NON-METHANE ORGANIC CARBON ANALYZER (NMOC Method 25)

NON-METHANE ORGANIC CARBON ANALYZER (NMOC Method 25) Gas Chromatography NON-METHANE ORGANIC CARBON ANALYZER (NMOC Method 25) The Non-Methane Organic Compounds (NMOC) Analyzer is a gas chromatograph configured for analyzing gaseous samples for total organic

More information

Gamma Radiation Effects on Benzoxazine Monomer: Curing and Thermal Properties

Gamma Radiation Effects on Benzoxazine Monomer: Curing and Thermal Properties 2011 International Conference on Chemistry and Chemical Process IPCBEE vol.10 (2011) (2011) IACSIT Press, Singapore Gamma Radiation Effects on Benzoxazine Monomer: Curing and Thermal Properties Sunan Tiptipakorn

More information

Maximizing Performance Through GPC Column Selection

Maximizing Performance Through GPC Column Selection Maximizing Performance Through GPC Column Selection What Are Polymers? Polymers are long chain molecules produced by linking small repeat units (monomers) together There are many ways to link different

More information

Supplementary Material

Supplementary Material Supplementary Material Title: Optical Characterization of Non-Covalent Interaction between Non-Conjugated Polymers and Chemically Converted Graphene Author: Yufei Wang A, Xueliang Hou A, Chi Cheng A, Ling

More information

GPC/SEC Practical Tips and Tricks. Thomas Dent Applications Scientist Agilent Technologies. October, 2011 Gulf Coast Conference

GPC/SEC Practical Tips and Tricks. Thomas Dent Applications Scientist Agilent Technologies. October, 2011 Gulf Coast Conference GPC/SEC Practical Tips and Tricks Thomas Dent Applications Scientist Agilent Technologies October, 2011 Gulf Coast Conference 1 Section 1: Introduction Goals Brief introduction to GPC/SEC Highlight considerations

More information

Standard Operating Procedure for the Analysis of Dissolved Inorganic Carbon CCAL 21A.1

Standard Operating Procedure for the Analysis of Dissolved Inorganic Carbon CCAL 21A.1 Standard Operating Procedure for the Analysis of Dissolved Inorganic Carbon CCAL 21A.1 Cooperative Chemical Analytical Laboratory College of Forestry Oregon State University 321 Richardson Hall Corvallis,

More information

HYPHENATED TECHNOLOGY GUIDE

HYPHENATED TECHNOLOGY GUIDE HYPHENATED TECHNOLOGY GUIDE TABLE OF CONTENTS TG-IR...3 Hiden Analytical MS Systems for TG-MS...4 TG-MS...5 TG-GC/MS...6 TG-IR-GC/MS...8 HYPHENATED TECHNOLOGY GUIDE Coupling, or hyphenating, two instruments

More information

Material Testing Report SN 7131 ISOFIL HK 30 TTH0 WT0822

Material Testing Report SN 7131 ISOFIL HK 30 TTH0 WT0822 Material Testing Report SN 7131 ISOFIL HK 30 TTH0 WT0822 Prepared for: SIRMAX SPA Via Dell Artigianato 42 Cittadella 35013 Italy Prepared by: Autodesk Moldflow Plastics Labs 2353 N. Triphammer Rd. Ithaca,

More information

Monitoring Emulsion Polymerization by Raman Spectroscopy

Monitoring Emulsion Polymerization by Raman Spectroscopy An Executive Summary Monitoring Emulsion Polymerization by Raman Spectroscopy Why process analytical matters to process development R&D. Serena Stephenson, PhD Senior R&D Analytical Manager Kishori Deshpande,

More information

Research Equipment in the UCA Chemistry Department

Research Equipment in the UCA Chemistry Department Research Equipment in the UCA Chemistry Department Varian 220 Atomic Absorption Spectrometer Atomic Absorption spectroscopy is used to measure the amount of a metal ion present in a solution. It is particularly

More information

Supporting Information. T g [ºC] b) E at 23 ºC [MPa]

Supporting Information. T g [ºC] b) E at 23 ºC [MPa] Supporting Information α-amino Acid-Based Poly(Ester Urea)s as Multi-Shape Memory Pol-ymers for Biomedical Applications Gregory I. Peterson, Andrey V. Dobrynin, Matthew L. Becker* The University of Akron,

More information

Qualitative analysis of aramide polymers by FT-IR spectroscopy

Qualitative analysis of aramide polymers by FT-IR spectroscopy International Journal of Engineering Science Invention ISSN (Online): 2319 6734, ISSN (Print): 2319 6726 Volume 3 Issue 2 ǁ February 2014 ǁ PP.01-07 Qualitative analysis of aramide polymers by FT-IR spectroscopy

More information

Electronic Supporting Information for

Electronic Supporting Information for Electronic Supporting Information for Microporous metal-organic open framework containing uncoordinated carbonyl groups as postsynthetic modification sites for cation exchange and Tb 3+ sensor Jianwei

More information

Harris: Quantitative Chemical Analysis, Eight Edition CHAPTER 23: GAS CHROMATOGRAPHY

Harris: Quantitative Chemical Analysis, Eight Edition CHAPTER 23: GAS CHROMATOGRAPHY Harris: Quantitative Chemical Analysis, Eight Edition CHAPTER 23: GAS CHROMATOGRAPHY Chapter 23. Gas Chromatography What did they eat in the year 1,000? GC of Cholesterol and other lipids extracted from

More information

Thermal and mechanical properties of several phthalonitrile resin system

Thermal and mechanical properties of several phthalonitrile resin system Thermal and mechanical properties of several phthalonitrile resin system Heng Zhou, Feng Liu, Yuehai Li, Tong Zhao* Institute of Chemistry, Chinese Academy of Sciences, Beijing, 100190, China Abstract:An

More information

The DialPath Solution an Easier Way to Analyze Liquids By FTIR. Yanqia Wang, Ph.D. Application Engineer - FTIR Agilent Technologies May 7, 2015

The DialPath Solution an Easier Way to Analyze Liquids By FTIR. Yanqia Wang, Ph.D. Application Engineer - FTIR Agilent Technologies May 7, 2015 The DialPath Solution an Easier Way to Analyze Liquids By FTIR Yanqia Wang, Ph.D. Application Engineer - FTIR Agilent Technologies May 7, 2015 Outline Background of FTIR Transmission Technology Traditional

More information

Course Description. * LC: Lecture; LB: Laboratory; LL: Lecture/Lab; SM: Seminar; SP: Senior Project; IN: Internship; LI: Lecture/Internship

Course Description. * LC: Lecture; LB: Laboratory; LL: Lecture/Lab; SM: Seminar; SP: Senior Project; IN: Internship; LI: Lecture/Internship * : Lecture; LB: Laboratory; LL: Lecture/Lab; SM: Seminar; SP: Senior Project; IN: Internship; LI: Lecture/Internship ** FN: Foundation; UG: Undergraduate; DP: Diploma; : Master; CR: Certificate Course

More information

MODULE 4.3 Atmospheric analysis of particulates

MODULE 4.3 Atmospheric analysis of particulates MODULE 4.3 Atmospheric analysis of particulates Measurement And Characterisation Of The Particulate Content 1 Total particulate concentration 1 Composition of the particulate 1 Determination of particle

More information

SURFACE MODIFICATION OF POLYPROPYLENE BY PHOTOGRAFTING OF VINYL ACETATE MONOMERS

SURFACE MODIFICATION OF POLYPROPYLENE BY PHOTOGRAFTING OF VINYL ACETATE MONOMERS Bulletin of the Transilvania University of Braşov Series I: Engineering Sciences Vol. 4 (53) No. 1-2011 SURFACE MODIFICATION OF POLYPROPYLENE BY PHOTOGRAFTING OF VINYL ACETATE MONOMERS J. BALART 1 J.M.

More information

Final Report. Characterisation of Sample Report. Job No 2016/11/12-34 AS No. 1234A. Client Example Contact Sample. Signed Date 2017.

Final Report. Characterisation of Sample Report. Job No 2016/11/12-34 AS No. 1234A. Client Example Contact Sample. Signed Date 2017. Final Report Title Characterisation of Job No 2016/11/12-34 AS No. 1234A Client Contact Sample Author report Signed Date 2017 Easy Reach Report 2017 v2.docx 1 of 33 Contents 1. Study Summary Page 3 2.

More information

Hach Method Total Organic Carbon in Finished Drinking Water by Catalyzed Ozone Hydroxyl Radical Oxidation Infrared Analysis

Hach Method Total Organic Carbon in Finished Drinking Water by Catalyzed Ozone Hydroxyl Radical Oxidation Infrared Analysis Hach Method 1061 Total Organic Carbon in Finished Drinking Water by Catalyzed Ozone Hydroxyl Radical Oxidation Infrared Analysis Hach Company Method 1061 Revision 1. December 015 Organic Carbon in Finished

More information

Analysis of Polymers and Plastics. Innovation with Integrity. Quality Control & Failure Analysis FTIR

Analysis of Polymers and Plastics. Innovation with Integrity. Quality Control & Failure Analysis FTIR Analysis of Polymers and Plastics Quality Control & Failure Analysis Innovation with Integrity FTIR Quality Control for Cost-Efficiency Plastics are used in countless products such as automotive parts,

More information

Halogen Free Flame Retardant Based on Organophosphorus Compounds for Expandable Polystyrene Produced by Supension Polymerization

Halogen Free Flame Retardant Based on Organophosphorus Compounds for Expandable Polystyrene Produced by Supension Polymerization Halogen Free Flame Retardant Based on Organophosphorus Compounds for Expandable Polystyrene Produced by Supension Polymerization Silvia A.C. Abarca 1* ; Ricardo A.F. Machado 1 ; Mariana Bianchi 1 Chemical

More information

Nanotribology Application in the Coining Industry (II) Optimization of Lubricant Film Formation on Blanks

Nanotribology Application in the Coining Industry (II) Optimization of Lubricant Film Formation on Blanks Nanotribology Application in the Coining Industry (II) Optimization of Lubricant Film Formation on Blanks Extended Abstract As discussed in the Nanotribology surface thermodynamic model, the reaction rate

More information

I. 16. Coloration of Polyethylene Terephthalate (PET) Film by 3MeV Proton Beams

I. 16. Coloration of Polyethylene Terephthalate (PET) Film by 3MeV Proton Beams CYRIC Annual Report 2001 I. 16. Coloration of Polyethylene Terephthalate (PET) Film by 3MeV Proton Beams Matsuyama S., Ishii K., Yamazaki H., Endoh H., Yuki H., Satoh T., Sugihara S., Amartaivan Ts., Tanaka

More information

A Novel Additive Concept for the Stabilization of ABS

A Novel Additive Concept for the Stabilization of ABS A Novel Additive Concept for the Stabilization of ABS A Novel Additive Concept for the Stabilization of ABS Alex Wegmann Ciba Specialty Chemicals Inc., Plastic Additives Segment, CH-4002 Basel / Switzerland.

More information

Marine bio-inspired underwater contact adhesion

Marine bio-inspired underwater contact adhesion Marine bio-inspired underwater contact adhesion Sean K. Clancy, Antonio Sodano, Dylan J. Cunningham, Sharon S. Huang, Piotr J. Zalicki, Seunghan Shin, * and B. Kollbe Ahn * Marine Science Institute, University

More information

Rheology Of Reinforced Polypropylene Melt Flow

Rheology Of Reinforced Polypropylene Melt Flow Rheology Of Reinforced Polypropylene Melt Flow Dr. Sadek Rejeibi, Dr.Abdelati Elalem, Dr.Omer Algydi Department of Chemical Engineering, Faculty of Engineering -Tripoli University Abstract: Different techniques

More information

Surface Hydrophilic Treatment of Polyester Films via UV irradiation

Surface Hydrophilic Treatment of Polyester Films via UV irradiation Surface Hydrophilic Treatment of Polyester Films via UV irradiation Gwang Hoe Koo, Hae Sung Lee and Jinho Jang School of Advanced Materials and System Engineering, Kumoh National Institute of Technology,

More information

Supporting Information

Supporting Information 1 Supporting Information 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Materials and Methods Experiment In this study, an alloy IR probe which allowed us to get access to spectral

More information

Gas Chromatography (Chapter 2 and 3 in The essence of chromatography)

Gas Chromatography (Chapter 2 and 3 in The essence of chromatography) Gas Chromatography 1. Introduction. Stationary phases 3. Retention in Gas-Liquid Chromatography 4. Capillary gas-chromatography 5. Sample preparation and injection 6. Detectors (Chapter and 3 in The essence

More information

CARBON NANOTUBE-POLYMER COMPOSITES: AN OVERVIEW Brian Grady University of Oklahoma

CARBON NANOTUBE-POLYMER COMPOSITES: AN OVERVIEW Brian Grady University of Oklahoma CARBON NANOTUBE-POLYMER COMPOSITES: AN OVERVIEW Brian Grady University of Oklahoma Abstract Carbon nanotubes are in many ways similar to polymers. Both molecules have contour lengths typically on the order

More information

Chromatographic Methods of Analysis Section: 5 Gas Chromatography (GC) Prof. Tarek A. Fayed

Chromatographic Methods of Analysis Section: 5 Gas Chromatography (GC) Prof. Tarek A. Fayed Chromatographic Methods of Analysis Section: 5 Gas Chromatography (GC) Prof. Tarek A. Fayed Gas Chromatography (GC) In gas chromatography, the sample is vaporized and injected onto the head of a chromatographic

More information

Chapter 31 Gas Chromatography. Carrier Gas System

Chapter 31 Gas Chromatography. Carrier Gas System Chapter 31 Gas Chromatography GAS-LIQUID CHROMATOGRAPHY In gas chromatography, the components of a vaporized sample are fractionated as a consequence of being partitioned between a mobile gaseous phase

More information

SYNERGETIC EFFECT OF UV LIGHT ON TOLUENE DECOMPOSITION BY DIELECTRIC BARRIER DISCHARGE

SYNERGETIC EFFECT OF UV LIGHT ON TOLUENE DECOMPOSITION BY DIELECTRIC BARRIER DISCHARGE SYNERGETI EFFET OF UV LIGHT ON TOLUENE DEOMPOSITION Y DIELETRI ARRIER DISHARGE R. Pyagay, 1 J-S. Kim, 2. Ahn, 2 Y-S. Yim 2 1 hemistry department, Lomonosov Moscow State University, Moscow 119-992, Russia

More information

Advanced Pharmaceutical Analysis

Advanced Pharmaceutical Analysis Lecture 2 Advanced Pharmaceutical Analysis IR spectroscopy Dr. Baraa Ramzi Infrared Spectroscopy It is a powerful tool for identifying pure organic and inorganic compounds. Every molecular compound has

More information

Analysing Phenol-Formaldehyde Resin Reaction For Safe Process Scale Up

Analysing Phenol-Formaldehyde Resin Reaction For Safe Process Scale Up SYMPOSIUM SERIES NO 16 HAZARDS 25 215 IChemE Analysing Phenol-Formaldehyde Resin Reaction For Safe Process Scale Up David Dale, Process Safety Manager, SciMed/Fauske and Associates, Unit B4, The Embankment

More information

Fourier transform infrared spectroscopy (FTIR) is a method used to obtain an infrared

Fourier transform infrared spectroscopy (FTIR) is a method used to obtain an infrared Fourier Transform Infrared Spectroscopy: Low Density Polyethylene, High Density Polyethylene, Polypropylene and Polystyrene Eman Mousa Alhajji North Carolina State University Department of Materials Science

More information

Analysis of Trace (mg/kg) Thiophene in Benzene Using Two-Dimensional Gas Chromatography and Flame Ionization Detection Application

Analysis of Trace (mg/kg) Thiophene in Benzene Using Two-Dimensional Gas Chromatography and Flame Ionization Detection Application Analysis of Trace (mg/kg) Thiophene in Using Two-Dimensional Gas Chromatography and Flame Ionization Detection Application Petrochemical Authors James D. McCurry and Bruce D. Quimby Agilent Technologies

More information

Studies of the uptake of gaseous ethyl-3-ethoxy propionate onto ammonium sulfate and ammonium nitrate aerosol particles

Studies of the uptake of gaseous ethyl-3-ethoxy propionate onto ammonium sulfate and ammonium nitrate aerosol particles Air Pollution XIII 519 Studies of the uptake of gaseous ethyl-3-ethoxy propionate onto ammonium sulfate and ammonium nitrate aerosol particles K. D. Stewart & J. M. Andino Department of Environmental Engineering

More information